This reverts commit 53147c2237.
These config changes break booting on C2600 and probably other devices.
Signed-off-by: Josh Bendavid <joshbendavid@gmail.com>
Commit 9ff8928bb9 renamed the snd-soc-mt7620-i2s
driver and dropped snd-soc-mt7620-wm8960 which selected CONFIG_SND_SOC_WM8960
breaking all ramips builds due to undefined kernel config symbols.
Rework the kmod-sound-mt7620 package to explicitely select the
CONFIG_SND_SOC_WM8960 symbols and change it to bundle the renamed .ko file.
Also remove the @BROKEN flag and exclude it on the rt288x subtarget instead.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
DuZun DM06 is a develop board based on mt7628
64M RAM, 8M SPI Flash, 1 WAN, 1 LAN.
wm8960 codec with line out, line in and speaker output.
Signed-off-by: Michael Lee <igvtee@gmail.com>
* remove mt7620-wm8960.c use simple card and DTS to do it
* add old chips support
* add 12Mhz refclk setup. this is hard code. need use clock framework
rewrite it
* add interrupt error status support for debug. default disable it.
because it cause to many interrupts
* add setup bclk suport not hard code it
* add 24 bits support for mt7628. not verified
* use regmap api to control registers
* add txdma-req/rxdma-req DTS params for DMA use
Signed-off-by: Michael Lee <igvtee@gmail.com>
* add rt_i2c structure to store driver data
* rewrite read/write check function and add i2c error status check.
so we don't need to wait until time out.
* add 10 bits address support. according to the data sheet i think
it is possible. but i haven't verify it.
* the most important is start transfer only need once. otherwise
it cause I2C_STARTERR status.
* add set i2c clock speed register by dts options "clock-frequency".
not just hard code it.
* add mt7621 i2c driver. i just copy i2c-ralink.c and change register
names. and the hardware don't support error status. so i remove it.
but the logic is the same.
Signed-off-by: Michael Lee <igvtee@gmail.com>
* fix compiler error. device_control operation not support now.
* add old chips support 8 channels. new chips support 16 channels.
* add mt7621 hsdma driver. data sheet says it has two channels.
but after test only one channel support.
* add memory to memory DMA support. i use dmatest kernel module to
verify this function. on rt305x it will copy more data. on mt7621
only two channels can works at the same time. these two chips
maybe have hardware bugs. because on other chips don't have these bugs.
* use tasklet to handle remaining dma requests.
Signed-off-by: Michael Lee <igvtee@gmail.com>
In commit "regulator: qcom: Rework to single platform device" the smb208
regulator used in IPQ8064 was left out.
Add it to that new framework and update Docs and DT accordingly.
Signed-off-by: Adrian Panella <ianchi74@outlook.com>
this worked in 3.18 but broke at some point. the old code that loaded a
irq table was incorrewct anyhow as it mapped the irqs int he domain which
should really be done when the driver using them loads them and not the
irq driver itself.
Signed-off-by: John Crispin <john@phrozen.org>
The swconfig kernel infrastructure fails to do any permissions checks when
changing settings. As such an ordinary user account on a device with a
switch can change switch settings without any special permissions.
Routers generally have few non-admin users so this isn't a big hole, but it
is a security hole. Likely the greatest danger is for multifunction devices
which have a lot of extra daemons, compromising a low-security daemon would
allow one to modify switch settings and cause the router/switch to appear to
lock-up (or cause other sorts of troublesome nyetwork behavior).
Implement a check for CAP_NET_ADMIN in swconfig_set_attr() and deny any
requests originating from user contexts lacking this capability.
Reported-by: Elliott Mitchell <ehem+openwrt@m5p.com>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
kmod-sound-soc-digidac1-soundcard is also missing snd-soc-wm8804 dependency
for snd-soc-wm8804-i2c
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
As usual these patches were extracted from the raspberry pi repo:
https://github.com/raspberrypi/linux/tree/rpi-4.4.y
Also alphabetically order sound-soc kernel packages.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
- Use KERNEL_INITRAMFS_SUFFIX for customizing initramfs name.
- Modifying $(PROFILES) is no longer needed.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Now that deviations to the default /etc/config/system are registered via
board.d we can drop the target specific copy.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Now that deviations to the default /etc/config/system are registered via
board.d we can drop the target specific copy.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The system config file shipped by ath25 is now equivalent to the generic one
in base files, so drop the target specific copy.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The ath25 target has its own unique button action config support, which is not
used anywhere except for two example logger statements in UCI.
Since there is a generic /etc/rc.button facility since some time already there
is no reason at all to keep this target specific mechanism anymore, so simply
drop it.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This patch adds the target profile SOM9331 and configures hardware
functionality for the 3x Eth Ports & corresponding LED's, the USB Host,
the USART to USB bridge and the System LED.
Signed-off-by: Allan Nick Pedrana <nik9993@gmail.com>
Upstream dropped the `dapm` member of `struct snd_soc_component`, requiring
users to access it using `snd_soc_codec_get_dapm()` instead so change the
driver code to do just that.
Fixes the following build error spotted by the buildbots:
CC [M] sound/soc/gw-avila/gw-avila.o
sound/soc/gw-avila/gw-avila.c: In function 'avila_aic3x_init':
sound/soc/gw-avila/gw-avila.c:104:44: error: 'struct snd_soc_codec' has no member named 'dapm'
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* build for pentium4 instead of i486
* enable PAE
* enable EFI support
* enable KVM guest and host support
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use the DMI data available in sysfs to extract manufacturer and model info
and write it to /tmp/sysinfo/.
The data will be picked up by board_detect and can be used by e.g. LuCI to
display a more appropriate model description.
On an APU board the files will contain the following values:
# cat /tmp/sysinfo/model
PC Engines APU
# cat /tmp/sysinfo/board_name
pc-engines-apu
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Enable support for DMI decoding in the kernel so that we can access
manufacturer and model information via sysfs.
Also remove redundant per-subtarget DMI overrides and preset a few
previously unset symbols popping up due to the now enabled DMI support.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
most symbols should be in Kernel packages
depending on HW the removal of
CONFIG_REALTEK_PHY
and USB symbols might be wrong
compile tested only
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
Initially for ARC we were building vmlinux images because it
was both simpler and more convenient to debug Linux kernel
in runt-time via JTAG. Now when base system works quite nice
we may finally use U-Boot for loading the system image as
well. Still we keep building vmlinux images as some of our
boards are development boards and loading images with JTAG
could be at some points very beneficial.
Note for U-Boot header it's required to specify 2 values:
* loading address
* entry point (if it doesn't match loading address)
and in case of ARC entry point (EP) not only differs from
loading address but also changes from build to build due to
initramfs being placed between loading address and text section.
To accommodate that feature we have to calculate EP after
vmlinux gets built and before call to mkimage.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
even it's a little bit verbose, unmacrod board descriptions are much
easier to read and to understand.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
This patch adds support for the Netgear EVG2000 VoIP Gateway to the
bcm63xx targets.
This device was not sold to the general public, but rather is/was
provided by telcos to customers in Sweden, Australia, Singapore and
other parts of asia.
Known issues:
- Unable to detect 53115 switch. This appear to be a problem with
probing for the PHY using MDIO and results in error 5. Doesn't seem to
be a problem with the configuration, and could use someone with
experience to have a look at it.
- Uses the b43 driver as using the OpenWRT/LEDE broadcom-wl driver
fails to load the firmware for the 4322, so 802.11n is not supported.
More info on the device and the research can be found at:
https://wiki.openwrt.org/toh/netgear/evg2000https://wikidevi.com/wiki/Netgear_EVG2000https://github.com/Xotic750/mirror-lede/tree/evg2000https://forum.openwrt.org/viewtopic.php?id=63950
Signed-off-by: Graham Fairweather <xotic750@gmail.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Some devices with ath9k WiFi require changing the default active low
polarity to high in order to correctly operate the WiFi status LEDs.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
These scripts were causing ip issues in the latest version of LEDE:
https://gist.github.com/Noltari/6d20d8bcbe236caf516c0a73f5477d00
Fixes preinit iface script by making eth0 the default ifname and only changing
it to eth1 for the devices that specifically need it.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
- Use default number of uarts (2) for rt288x/rt305x/rt3883/mt7620.
- Allow up to 3 uarts on MT7621 and MT7628.
- Remove unneeded SERIAL_8250_RT288X for MT7628.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The Widora board is similar to the Linkit 7688 but features a larger flash
capacity.
Signed-off-by: Yuan Chenmang <771992497@qq.com>
[Jo-Philipp Wich: Reword commit message, cleanup initial PR]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The previous image creation code would have failed if the
unpadded kernel uImage size was less than 64 bytes from the
next erase block boundary. Fix that.
Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
The CPE210 was still described for the OEM upgrade as compatible,
even the wireless configuration isn't compatible anymore between
both series (2ghz and 5ghz).
Update the CPE210 image profile to use the new profile.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
The CPE210's ancestor is the CPE510 not the other way around. The device
profile is also named after the CPE510.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
The bootloader on this device expects the kernel partition to end
on a 64k boundary. The last 64 byte of the kernel partition must
contain a valid uImage header (the fakeroot partition).
Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
1)Changes
- Rebased the patches for linux-4.4.7
- Added patch to fix spi nor fifo and dma support
- Added patch to configure watchdog barktime
2)Testing
Tested on IPQ AP148 Board:
a. NOR boot and NAND boot
b. ethernet network and ath10k wifi
c. ubi sysupgrade
UnTested
dwc3 usb has not been validated on IPQ board(AP148)
3)Known Issues:
Once we flash ubi image on AP148, and if we reset the board, uboot on
first boot creates PEB and LEB for dynamic sized partitions, which is incorrect
and not what linux expects which causes errors when trying to mount rootfs.
In order to test this, we can use the below steps:
a. Flash the ubi image on board and don't reset the board
b. load the kernel fit image in RAM and boot from there.
Signed-off-by: Ram Chandra Jangir <rjangi@codeaurora.org>
The user benpicco in #openwrt reported that images are build which are
bigger that the available flash size.
He provided a proof of concept fix and gave permission to me to send it
for inclusion.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The RJ45 WAN port is used for xDSL as well as the IP101A.
The pins 1,2,3,6 of the RJ45 are connected to the IP101A and the
pins 4,5 are connected to the xdsl chip.
Drop the ip101a-rst node. It can't be controlled and is not required
at all.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The STP pinmux was initially added in assumption LAN2 led is driven by
it. It worked somehow because STP group and gphy0 led0 share the GPIO.
Do it the right way by adding the gphy0 led0 the gphy function.
According to the author, the SPI node is a copy & paste leftover. Which
makes sense since nothing is connected to the SPI bus on this device.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use the brnboot partition layout as it is listed in the OpenWrt wiki
article for this board.
Configure the brnboot root selector for this device as well.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Cleanup the pinmux configuration by removing the unused spi node. Nothing is connected to the SPI bus on devices.
The stp_out pinmux child node covers the same GPIOs as the already used
stp group.
The same applies to the gphy-leds_out pinmux node and the "gphy0
led1" as well as "gphy1 led0" groups.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This patch fixes the missing Lan interface config in the file
/etc/config/network for ARV4518PWR01/A which results in eth0 and br-lan
being down and therefore no way to access the router unless via UART-TTL.
Signed-off-by: Mohammed Berdai <mohammed.berdai@gmail.com>
RB912 has one usb shared between external USB and miniPCIe slot. GPIO52 can
reroute power to external USB (=1) or internal miniPCIe slot (=0)
Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
Commit d79f8909c1 introduced CONFIG_ALL,
CONFIG_ALL_KMODS and CONFIG_ALL_NONSHARED as menuconfig choices to the SDK,
therefor we can drop the hardcoded CONFIG_ALL symbol declaration now.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Now that the most important options are exposed via menuconfig in the SDK we
can stop shipping a (possibly outdated) copy of .config from the emitting
buildroot.
Leaving out .config has two positive side effects:
- A simple "make" run without any prior config will launch menuconfig, forcing
interactive users to make appropriate choices
- Buildbot systems (e.g. our phase2 builder) can issue a "make defconfig" to
obtain a .config enabling all packages by default
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The query for ARMADA_THERMAL is stalling the kconfig process and as long as we
do not package it, simply disable the symbol.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Generalize the partition discovery in sysupgrade in order to fix sysupgrade
and config backup/recovery on MMC block devices which use a different naming
scheme compared to mtdblock or sd* devices.
The change also adds the find applet to the ramdisk utilities so that upgrade
code can rely on it.
The commit is based on the initial submission by Russell Senior at
http://patchwork.ozlabs.org/patch/625440/ .
Signed-off-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
It is desirable to be able to use ./scripts/feeds install -a
when in the SDK without being forced to build a great number
of packages that are not actually wanted.
We therefore add the option of changing the various ALL package
build options so that we can default to packages not being built
unless we select them.
Signed-off-by: Daniel Dickinson <lede@daniel.thecshore.com>
The cpe510 has two calibration tables. The first calibration
table requires to modify ath9k driver to work (patched tx gain table).
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
The CE image format used by OpenMesh can contain extra blocks which
are not used for flashing. Only the first three embedded images
(fwupgrade.cfg, kernel, rootfs) are required in this order to successfully
flash an image via sysupgrade. All extra embedded images should be ignored
for the available devices.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
The platform_check_image_openmesh function used break statements to signal
that the board name matched the image target. This worked because the
sysupgrade binary checked the image inside a loop. The break statement
stopped the loop and skipped any additional check.
Instead the check should be done without such sideeffects by simply
combining the board names and image targets. Only a mismatch should cause a
negative result for the caller and skipping of the additional checks.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Some OpenWrt based firmwares like Gluon expect that a sysupgrade image
exists when a device firmware can be updated via sysupgrade. This image
wasn't created until now because OpenMesh devices use the same image for
factory and sysupgrade flash. Copying the image from *factory.bin to
*sysupgrade.bin is therefore enough to make the sysupgrade functionality
visible.
Reported-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Josh Bendavid
John Crispin
Dirk Neukirchen
Jo-Philipp Wich
Rafał Miłecki
Felix Fietkau
Arne Zachlod
Henryk Heisig
Michael Lee
Adrian Panella
Álvaro Fernández Rojas
Ben Whitten
Allan Nick Pedrana
Daniel Golle
KeLei Liang
Joseph C. Lehner
Alexey Brodkin
Alexander Couzens
Ash Benz
Ted Hess
Graham Fairweather
Yuan Chenmang
Stijn Segers
Daniel Gimpelevich
Ram Chandra Jangir
Mathias Kresin
Mohammed Berdai
Cezary Jackiewicz
Daniel Dickinson
Claudio Leite
Sven Eckelmann