fix inclusion of functions.sh in dsl_fs init script
without this, the following error is seen during build:
./etc/init.d/dsl_fs: line 4: /lib/functions.sh: No such file or directory
Signed-off-by: Thomas Langer <thomas.langer@lantiq.com>
SVN-Revision: 42575
The bb-rc3 image for the BTHOMEHUBV2B is too big for its
mtd partition. This patch corrects the partition sizes in
the device tree. This patch should really go in before
bb-final, otherwise the BTHOMEHUBV2B images won't be useable.
I do apologise for not spotting this straight away.
Many thanks,
Ben
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
SVN-Revision: 42316
- use full board name
- rename uboot-env partition
- add dsl_fw partition
- remove unneeded pinmux groups
- move gigabit ethernet to LAN
- load mac address from mtd
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 42180
Run lantiq_board_detect from lantiq_board_name and lantiq_board_model.
This was the one thing missing from r41474 for sysupgrade board
detection to work properly.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
SVN-Revision: 41567
Disables gluebi and enables ubiblock on lantiq xway. Squashfs
images on nand use ubifs instead of jffs2 for the overlay.
I'll leave the equivalent patch for xrx200 to someone who has a
board to test.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
SVN-Revision: 41565
New make target in lantiq to use UbinizeImage and SysupgradeNand.
Only enabled for BTHOMEHUBV2B for the moment but should be useable
for other lantiq nand boards.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
SVN-Revision: 41474
Enable LANTIQ_PHY and LANTIQ_XRX200 only in XRX200 subtarget.
These drivers are not needed for ASE, Danube and AR9.
As side effect PHY11G and PHY22F firmwares are not included in the
kernel image, which saves 64 KB.
Signed off by: José Vázquez Fernández <ppvazquezfer@gmail.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41449
205-fix-headers_install.patch is obseleted by upstream commit 3246a0352e3d58380b9386570f1db1faf7edf8a8
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41351
As far as I am aware, amongst the lantiq boards, jffs2_nand was
only used on the BTHOMEHUBV2B. Ubi-related modifications to the
device tree for that board mean that the resulting jffs2 images
no longer work, and are no longer required anyway. So I suggest
removing the related configuration, which this patch does.
If anyone else is using jffs2_nand on a lantiq target please speak
up!
Incidentally, for a jffs2 rootfs partition concatenated to the
kernel image to be recognised and mounted correctly on nand
this patch or something equivalent is required:
http://patchwork.openwrt.org/patch/5110/
It is marked as accepted in patchwork but doesn't seem to have
been committed. As far as I am concerned it too is deprecated.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
SVN-Revision: 41312
Setting this flag allows rootfs_data to expand on first boot
to fill remaining free space on nand.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
SVN-Revision: 41310
At the moment, an rootfs.ubi is copied over to bin/lantiq
but rootfs-overlay.ubi is not. This adds it.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
SVN-Revision: 41270
This patch adds factory image building for the DGN3500, all variants,
and fixes sysupgrade images to make them play nice with the sercomm
secondary boot loader.
The factory images can be used directly in the update dialog in the
interface of the stock firmware and via the special Sercomm bootmode
and a special windows flashing utility (allegedly present in the CD
that came with the device -- but it's also compatible with the NSLU2
Upgrade_207_XP utility.) The special bootmode can be activated by
turning the device on while holding the reset button pressed, then
releasing it when the power led starts blinking red and green. Please
notice that if using the 207 utility, it will always report that the
flashing failed even though it completed successfully. Just power
cycle the router manually after the utility reports the failure and
OpenWRT will boot. This same utility (despite reporting failure in
this case too) can revert a DGN3500 (any variant) to the appropriate
stock Netgear firmware.
This patch is a heavily modified version of a package I found on the
OpenWRT forum with a couple fixes and features added -- mainly the
generation of all the different image variants to support all known
models directly, atm known variants are AnnexA-WW, AnnexA-NA and
AnnexB-DE/GR.
I tested the patch successfully on my device.
Signed-off-by: Marco Antonio Mauro <marcus90@gmail.com>
SVN-Revision: 41236
This patches the BTHOMEHUB2B device tree to make use of the
new code for automatic detection of the ubi partition and the
rootfs type within it. Gets rid of the ugly alternative bootargs
lines.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
Acked-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 41214
ath5k fix in wifi and ethernet eeprom handling patch.
Without the line that adds the patch of_ath5k_eeprom_probe cause a
kernel panic, at least with the ARV4518PW.
Tested only in the modem-router mentioned above.
This patch is based in Bruno's hack present in patch #5454.
Signed off by: Bruno Rodríguez <bruno.rodriguez.1980@gmail.com>
Signed off by: José Vázquez Fernández <ppvazquezfer@gmail.com>
SVN-Revision: 40999
ARGC is a 'C-ism', but not known/valid in shell-syntax - insert the correct
var $# (=number of args) here. under normal conditions this had no impact,
but we should at least correct it. the error was observable like this:
root@box:~ [ -e "/etc/functions.sh" ] && . /etc/functions.sh
root@box:~ [ -e "/lib/functions.sh" ] && . /lib/functions.sh
root@box:~ . /lib/upgrade/platform.sh
root@box:~ . /lib/upgrade/common.sh
root@box:~ platform_check_image /tmp/myfirmware.bin
ash: bad number
root@box:~ echo $?
0
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
SVN-Revision: 40915
John Crispin
Gabor Juhos
Felix Fietkau