More device info at: http://wiki.openwrt.org/toh/tenda/w306r
Signed-off-by: David Pearce <David_18051985@hotmail.com.au>
[juhosg: fix checkpatch errors, remove kmod-phy and luci-ssl packages
from the profile, change broken GPIO number]
SVN-Revision: 31396
This patch adds support for the Accton WR6202 Mini 3G broadband router.
Full details for this device are available at
http://www.awbnetworks.com/products03.php?Fullkey=19.
This device is identical to the SMCWBR11S-3GN:
http://www.smc-asia.com/products03.php?Fullkey=210
It's also worth noting that this board has a GPIO line to control the
power to the USB port.
[juhosg:
- fix checkpatch warnings,
- reorder Kconfig entry,
- merge the sysupgrade patch,
- add GPL header]
Signed-off-by: Johnathan Boyce <jon.boyce@globalreach.eu.com>
SVN-Revision: 30434
This patch adds support for the Sitecom WL-341 v3 and other Sercomm
IP1006RRv2 based boards for sysupgrade support and for the initial
flash through pushbutton initiated recovery mode with the special
partition table and fixes for the quirks and things required by the
modified bootloader.
There is a known bug, Wi-Fi is not working on my board probably
because of the lack of RAM (the board only has 16MiB ram -- half of
the normal amount for non rebadged versions, but there is an empty
slot for another ram chip,) but I don't know for sure. The driver
loads but hostapd fails to load so I think it's not related to the
specific device except for the lack of RAM.
Moreover, only 7 of the 11 onboard leds are confirmed working, it
seems that one of the others is always on and the remaining ones are
connected to the wireless card leds already recognized by OpenWrt
[juhosg: reordered some parts in order to keep things sorted
alphabetically]
Signed-off-by: Marco Antonio Mauro <marcus90@gmail.com>
SVN-Revision: 29910
In this patch:
* rename Argus leds to avoid underscores
* rename Belkin F5D8235 v1 leds from f5d8234 to f5d8235
* remove Belkin F5D8235 v1 status led defined as storage led (it was
defined as usb led earlier, just in wrong place) - it should have
router led as in v2
* add Argus, Sparklan and Belkin F5D8235 v2 status leds
* add Belkin F5D8235 v1 and v2 usb leds
* fix Belkin F5D8235 v2 network config generation and mac address axtraction
* fix Sparklan board identification
* add Sparklan usb led (this board doesn't have usb connector by
default and the led is hidden also but if you are going to solder
the connector then you'll see the led too)
* add Sparklan network config generation and mac address extraction
* fix empty string test in network script and...
* ...sort case entries by the first board in the list
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 29871
This add support for the Sitecom WL-351 v1 002.
In principle the Engenius ESR9850 should also work with this, but I
don't have the hardware to test it.
Since an external gigabit switch (RTL8366RB) is used,
I had to modify the ramips_esw driver to add a 'bypass' mode, which
just configures it to not filter the vlan tags.
Also two initialization words (FCT2 and FPA2) are set to different
values by u-boot than what the driver is using and it only seems to
work correctly when they not overridden by the driver, so I
added them to the platform specific data as reg_initval_fct2 and
reg_initval_fpa2.
With this wired lan works as expected, however I'm still having some
trouble with the wireless lan:
It only works after I rmmod & re-insmod rt2800pci and then
reconfigure it in the webinterface, but not directly after
rebooting.
The symptom of this is wpad saying:
Dec 20 15:45:09 OpenWrt daemon.info hostapd: wlan1: STA <notebookmac> IEEE 802.11: associated (aid 1)
Dec 20 15:45:09 OpenWrt daemon.info hostapd: wlan1: STA <notebookmac> WPA: pairwise key handshake completed (RSN)
Dec 20 15:45:22 OpenWrt daemon.info hostapd: wlan1: STA <notebookmac> IEEE 802.11: authenticated
But wpa_supplicant on the client saying:
Authentication with <wl351mac> timed out.
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
SVN-Revision: 29604
Inspired by the patch from Roman Yeryomin. Thanks, Roman!
This removes unnecessary duplication and simplifies network setup for new
boards. It would be a one line change most likely.
[juhosg: setup lan and wan interfaces for unspecified rt3x0x based boards
in order to avoid regression]
Signed-off-by: Alexander Gordeev <lasaine@lvk.cs.msu.su>
SVN-Revision: 29376
The preconfiguration of the USB LED has benn move to the
/etc/uci-defaults/leds script. [juhosg]
Signed-off-by: Adam Porter <porter.adam at gmail.com>
SVN-Revision: 28571
This removes unnecessary duplication and simplifies led setup for new
boards. It would be a one line change most likely.
Signed-off-by: Alexander Gordeev <lasaine@lvk.cs.msu.su>
SVN-Revision: 28569
This change corrects expected CPU name of Ralink RT3050, which
describes itself as RT3350 (this name is ripped off chip and elevated
to user space via /proc/cpuinfo.)
This patch fixes wired network on DIR-300 rev B and DIR-600 rev B
Signed-off-by: Slawomir Cygan <wiewior@wiewior.eu.org>
SVN-Revision: 27804
Gabor Juhos
Jo-Philipp Wich
Florian Fainelli
John Crispin