67444c7795
ar71xx: pb44_spi: introduce pb44_spi_{en,dis}able helpers
...
SVN-Revision: 29708
2012-01-11 09:14:15 +00:00
0f566a376c
ar71xx: ar71xx_spi: add shutdown handler
...
This allows to access the flash from a kexec'd kernel.
SVN-Revision: 29707
2012-01-11 09:14:14 +00:00
09a6e3f662
ar71xx: ar71xx_spi: save and restore regs from probe/remove
...
SVN-Revision: 29706
2012-01-11 09:14:13 +00:00
714a9bd641
ar71xx: ar71xx_wdt: add shutdown handler
...
SVN-Revision: 29705
2012-01-11 09:14:11 +00:00
a1dcbc66a6
ar71xx: add initial support for the TL-WR2543N/ND board
...
The WLAN LEDs are not working yet.
SVN-Revision: 29680
2012-01-07 19:36:35 +00:00
67b2814842
ar71xx: local mac support on the wndr3700
...
The wndr3700 at least has no eth0 mac address and usually leverages
the first wireless device's mac when in a bridged scenario. If,
however, you want to route, and not bridge the interfaces, you
need a unique mac address for it.
This patch sets the local bit on the mac address pulled from the
wireless chip and uses the resulting address for eth0.
Patch-by: Dave Taht <dave.taht@gmail.com>
SVN-Revision: 29675
2012-01-07 17:24:44 +00:00
1e848b17ad
ar71xx: add support for Redwave RW2458N
...
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
SVN-Revision: 29669
2012-01-06 07:20:59 +00:00
8eb0b7ab3d
ar71xx: fix sections mismatch warnings in the nand drivers
...
SVN-Revision: 29667
2012-01-05 18:08:33 +00:00
b8f0d86115
ar71xx: add inital support for the ALFA Network AP96 board
...
The microSD slot and the Real Time Clock is not working yet.
The miniPCIe interface is not tested due to the lack of a
suitable card.
SVN-Revision: 29662
2012-01-04 21:13:54 +00:00
923f3e3752
ar71xx: allow to use the command line hack on compex devices
...
SVN-Revision: 29659
2012-01-04 17:30:58 +00:00
2f53f82203
ar71xx: use the TL-MR3x20 code for the TL-WR841N/ND v7
...
These models are based on the AP99 reference board,
and uses the AR7241 SoC.
SVN-Revision: 29658
2012-01-04 17:30:57 +00:00
90bfef9ec9
ar71xx: allow to use LAN LED on the TL-WA901N/ND boards
...
SVN-Revision: 29653
2012-01-04 17:30:50 +00:00
1045c83527
ar71xx: add support for TP-Link TL-MR3020
...
This patch adds support for the TP-Link device TL-MR3020 which is very
similiar to the TL-WR703N.
The TL-MR3020 uses 5 LEDs, 1 push button and a switch with 3 positions.
Only four LEDs can be controlled via GPIO. The power LED is connected to
the power supply.
The WPS push button has been mapped to KEY_WPS_BUTTON. The two GPIO signals
of the sliding switch have been mapped to BTN_0 and BTN_1.
I have also setup a wiki page with details here:
http://wiki.openwrt.org/toh/tp-link/tl-mr3020
USB is working and has been tested with USB mass storage and USB UMTS
stick.
Wifi also seems to work.
Ethernet is working too.
Signed-off-by: Christian Cier-Zniewski <c.cier@gmx.de>
SVN-Revision: 29651
2012-01-04 17:30:47 +00:00
1e68f10b87
ar71xx: add support for the ALFA Network N2/N5 boards
...
SVN-Revision: 29635
2012-01-01 19:30:25 +00:00
5c067db8a7
ar71xx: define LAN/WAN LEDs for the TL-WR741N/ND boards
...
SVN-Revision: 29631
2011-12-31 15:02:46 +00:00
8c2482f76e
ar71xx: ag71xx: implement get_port_{link,stats} callbacks
...
SVN-Revision: 29626
2011-12-31 15:02:26 +00:00
557009bbdb
ar71xx: fix LEDs on the WRT400N
...
SVN-Revision: 29624
2011-12-31 13:54:11 +00:00
db0a1db257
ar71xx: set a reserved bit that resets to 1 when writing the address table control register on the ar7240 switch (should fix #10547 )
...
SVN-Revision: 29598
2011-12-22 05:43:53 +00:00
ebefe1eb3a
the mach file of the WZR-HP-G300NH2 accidentally claimed the mach id of the WZR-HP-AG300H, correct the id ( #10649 )
...
SVN-Revision: 29593
2011-12-21 01:27:48 +00:00
11013ad947
ar71xx: add missing wireless led changes for wzr-hp-g300nh2
...
SVN-Revision: 29568
2011-12-19 09:04:15 +00:00
0cc056cb7e
ar71xx: add support for the wzr-hp-g300nh2
...
Signed-off-by: Mark Deneen <mdeneen@gmail.com>
SVN-Revision: 29567
2011-12-18 22:20:17 +00:00
67c7980290
ar71xx: connect GMAC0 to the internal switch on DB120
...
Because the external switch has no driver yet, connect GMAC0
to the PHY4 of the internal switch for now. This allows to
use the DB120 board as a router with 4LAN+1WAN ports.
SVN-Revision: 29557
2011-12-15 22:25:38 +00:00
5bbd416e38
ar71xx: add defines for the AR934X GMAC interface
...
SVN-Revision: 29556
2011-12-15 22:25:36 +00:00
e47a8c2bb2
ar71xx: fix GMAC1 interface speed on the DB120 board
...
SVN-Revision: 29555
2011-12-15 22:25:35 +00:00
36bc2c2c80
ar71xx: ag71xx: fix switch port setup for AR934X
...
SVN-Revision: 29554
2011-12-15 22:25:32 +00:00
00667c3846
ar71xx: ag71xx: allow to connect PHY4 to the CPU on AR934X
...
SVN-Revision: 29553
2011-12-15 22:25:30 +00:00
0540970345
ar71xx: ag71xx: setup switch interface mode on AR934X
...
SVN-Revision: 29552
2011-12-15 22:25:29 +00:00
44014110b8
ar71xx: ag71xx: detect the built-in switch of the AR934X SoCs
...
SVN-Revision: 29551
2011-12-15 22:25:28 +00:00
e2a546d475
ar71xx: allow to attach the internal switch for AR934x
...
SVN-Revision: 29550
2011-12-15 22:25:22 +00:00
9ae65588d8
ar71xx: introduce ar71xx_switch_data
...
SVN-Revision: 29549
2011-12-15 22:25:11 +00:00
850be54b72
ar71xx: tplinkpart: allow to detect JFFS2 as well
...
SVN-Revision: 29543
2011-12-15 22:03:40 +00:00
b7d7481b07
ar71xx: ag71xx: check PHY IDs before accessing the switch registers
...
SVN-Revision: 29541
2011-12-15 13:25:23 +00:00
0655552860
ar71xx: ag71xx: don't use port 4 of the switch, it is not connected on ar724x
...
SVN-Revision: 29540
2011-12-15 13:25:21 +00:00
204fc6bed5
ar71xx: ag71xx: nuke ar7240sw_init
...
SVN-Revision: 29539
2011-12-15 13:25:20 +00:00
d1f7783612
ar71xx: fix mac addresses on jjPlus devices
...
SVN-Revision: 29538
2011-12-15 13:25:18 +00:00
b9c5cb5c9a
ar71xx: add support for ALFA Network's Hornet-UB board
...
SVN-Revision: 29535
2011-12-14 20:54:10 +00:00
66c8cc0f6d
ar71xx: add GPIO function bit defines for AR933X
...
SVN-Revision: 29534
2011-12-14 20:54:07 +00:00
7076d74b21
ar71xx: fix gpio count for ar7241/ar7242
...
SVN-Revision: 29532
2011-12-14 20:47:24 +00:00
b878f4a927
ar71xx: register extra leds behind the wireless mac on wzr-hp-g450h
...
SVN-Revision: 29531
2011-12-14 20:21:42 +00:00
4a441570ca
kernel: move linux/ath9k_platform.h to generic files so that it can be reused from other targets
...
SVN-Revision: 29516
2011-12-13 15:14:59 +00:00
3806671fe5
ar71xx: fix wireless led on wzr-hp-g450h
...
SVN-Revision: 29515
2011-12-13 15:00:43 +00:00
2dd7dfb1c9
ar71xx: enable AR9341 support at setup.c
...
Patch-by: dyq <729650915@qq.com>
SVN-Revision: 29514
2011-12-13 14:59:43 +00:00
058998acdb
ar71xx: Build images for Netgear WNDRMAC and WNDRMACv2
...
The WNDRMAC is a WNDR3700v2 (64MB RAM, 16MB flash) in a white case. The
WNDRMACv2 is a WNDR3800 (128MB RAM, 16MB flash) in a WNDRMAC case.
The WNDRMAC case doesn't have "holes" or labels for the 2.4GHz LED or
switch ports 2-4. The stock firmware uses a single LED (in the 5GHz
position) to indicate the status of both radios, and a single LED (in the
switch port 1 position) to indicate the status of all LAN ports. The
"missing" LEDs are present on the board, and easily shine through the
case. Unlike the stock firmware, OpenWrt will use these "hidden" LEDs.
I've tested the WNDRMACv2 image. I don't have a v1 WNDRMAC, but assume
that this is sufficient to build a fully-functional image.
Signed-off-by: Mark Mentovai <mark@moxienet.com>
SVN-Revision: 29513
2011-12-13 14:59:40 +00:00
48f9717371
ar71xx: add gpios and usb for wzr-hp-g450h
...
SVN-Revision: 29509
2011-12-13 13:33:44 +00:00
4ca2d86493
ar71xx: use RedBoot parser on PB44
...
SVN-Revision: 29501
2011-12-11 15:52:47 +00:00
bdc2eca7de
ar71xx: use correct mac on the lan interface on several TP-LINK devices
...
SVN-Revision: 29458
2011-12-05 21:10:58 +00:00
0103069372
ar71xx: allow to pass negative offset values for ar71xx_init_mac
...
SVN-Revision: 29457
2011-12-05 21:10:55 +00:00
ada92aee62
ar71xx: don't register PCI controller on AR934x if PCIE_RC bit is not set
...
SVN-Revision: 29456
2011-12-05 18:21:15 +00:00
3e7a6d182a
ar71xx: check squashfs signature in TP-Link mtd parser
...
SVN-Revision: 29446
2011-12-05 14:52:33 +00:00
1f809532de
ar71xx: add preliminary support for wzr-hp-g450h
...
SVN-Revision: 29441
2011-12-05 14:20:51 +00:00
d1f63f8538
ar71xx: move multi-m25p80 concat code from wzr-hp-ag300h mach code to dev-m25p80.c, other buffalo routers use it as well
...
SVN-Revision: 29440
2011-12-05 14:20:44 +00:00
4cc2b9bb06
ar71xx: rewrite WNDR3700/3800 handling
...
SVN-Revision: 29434
2011-12-05 13:03:54 +00:00
7cfa39f032
ar71xx: use the tp-link parser on the tp-link boards
...
Also remove static partition maps.
SVN-Revision: 29416
2011-12-03 18:13:31 +00:00
514b1167c9
ar71xx: add mtd partition parser for the TP-Link boards
...
SVN-Revision: 29415
2011-12-03 18:13:27 +00:00
fc7fb29bae
ar71xx: run the RedBoot parser only on the RedBoot based boards
...
SVN-Revision: 29414
2011-12-03 18:13:25 +00:00
9cc28d5aa0
ar71xx: run the MyLoader parser only on the WP543 board
...
SVN-Revision: 29413
2011-12-03 18:13:23 +00:00
67a0b9aada
ar71xx: run the wrt160nl parser only on the WRT160NL board
...
Also remove static mtd partition definitions.
SVN-Revision: 29412
2011-12-03 18:13:20 +00:00
f188f1bad5
ar71xx: add support for Ubiquiti AirRouter
...
Signed-off-by: Gergely Barta <gergely.barta@printerfairkft.hu>
SVN-Revision: 29395
2011-12-01 22:49:02 +00:00
f20797306a
ar71xx: modify phy mask of the WP543 board
...
This fixes ethernet on newer boards. Based on a patch from #9702 .
SVN-Revision: 29328
2011-11-24 20:09:43 +00:00
c20d7378e5
ar71xx: fix wndr3800 machine name
...
This fixes the machine name in /proc/cpuinfo and luci status page machine name.
Signed-off-by: Petri Rosenström <petri.rosenstrom@gmail.com>
SVN-Revision: 29326
2011-11-24 20:09:38 +00:00
9990523a0f
ar71xx: set GE0 phy_mask for AR933x
...
SVN-Revision: 29274
2011-11-20 11:30:10 +00:00
f27548448b
ar71xx: fix USB LED on the DB120 board
...
SVN-Revision: 29126
2011-11-14 17:43:15 +00:00
6ebbb1329d
ar71xx: add a function for selecting output signal on a given GPIO pin
...
SVN-Revision: 29125
2011-11-14 17:43:14 +00:00
0c1d3617d7
ar71xx: fix GPIO function handling on AR934x
...
SVN-Revision: 29124
2011-11-14 17:43:13 +00:00
aa0c8c4885
ar71xx: add AR71XX_ prefix to GPIO_REG_* defines
...
SVN-Revision: 29123
2011-11-14 17:43:11 +00:00
62a7795afd
ar71xx: merge nand scan patch
...
SVN-Revision: 29122
2011-11-14 17:43:10 +00:00
12dae96097
ar71xx: fix a compiler warning
...
SVN-Revision: 29110
2011-11-14 13:07:47 +00:00
5ae0fd802c
ar71xx: fix GPIO count for AR934x
...
SVN-Revision: 29109
2011-11-14 13:07:45 +00:00
e52269364a
ar71xx: flush DDR writeback buffers for WMAC and PCIe on AR934X
...
SVN-Revision: 29108
2011-11-14 11:49:53 +00:00
3104d70552
ar71xx: use a dummy irq chip for WMAC and PCIe irq hadling
...
SVN-Revision: 29107
2011-11-14 11:49:51 +00:00
42e8ae09b5
ar71xx: add AR934X_RESET_REG_PCIE_WMAC_INT_STATUS defines
...
SVN-Revision: 29106
2011-11-14 11:49:49 +00:00
c15caea360
ar71xx: add an irq parameter for ar724x_pcibios_init
...
SVN-Revision: 29105
2011-11-14 11:49:47 +00:00
cf90b24bb9
ar71xx: remove hardwired interface parameters from mach-* files
...
SVN-Revision: 29103
2011-11-14 07:38:09 +00:00
defc79cb40
ar71xx: force hardwired interface parameters in ar71xx_add_device_eth
...
SVN-Revision: 29102
2011-11-14 07:38:07 +00:00
6f4bc1ce37
ar71xx: use if-else instead of conditional operators in ar71xx_add_device_eth
...
SVN-Revision: 29101
2011-11-14 07:38:05 +00:00
368bbc510b
ar71xx: enable has_gbit flag on AR724{0,1}
...
SVN-Revision: 29026
2011-11-13 17:36:36 +00:00
15d7016c9f
ar71xx: fixup onboard PCIe chip registration on the DB120 board
...
SVN-Revision: 29022
2011-11-13 12:48:03 +00:00
f623066e60
ar71xx: drop DB120_WMAC_MAC_OFFSET, it is not needed
...
SVN-Revision: 29021
2011-11-13 12:48:01 +00:00
d2316b2a45
ar71xx: ag71xx: add support for getting switch port link status
...
SVN-Revision: 29017
2011-11-13 11:27:04 +00:00
d0db89133c
ar71xx: remove mii_ctrl resources of the ethernet devices
...
SVN-Revision: 29016
2011-11-13 11:27:03 +00:00
34015ed6e8
ar71xx: ag71xx: remove unused mii_ctrl field from struct ag71xx
...
SVN-Revision: 29015
2011-11-13 11:27:01 +00:00
2d882cff23
ar71xx: ag71xx: remove unused mii_cfg related functions and defines
...
SVN-Revision: 29014
2011-11-13 11:27:00 +00:00
538a9493b9
ar71xx: set MII interface speed from the set_speed callbacks
...
SVN-Revision: 29013
2011-11-13 11:26:59 +00:00
93cd46be13
ar71xx: rename set_pll callback to set_speed in ag71xx_platform_data
...
Also rename the corresponding callback functions.
SVN-Revision: 29012
2011-11-13 11:26:57 +00:00
9579bb4267
ar71xx: ag71xx: remove MII interface setup code
...
SVN-Revision: 29011
2011-11-13 11:26:56 +00:00
da64ce8603
ar71xx: configure MII interface type from ar71xx_setup_phy_if_mode
...
SVN-Revision: 29010
2011-11-13 11:26:54 +00:00
5ad763075e
ar71xx: use the button for WPS control on the DB120
...
SVN-Revision: 28990
2011-11-12 12:50:20 +00:00
4555be2bec
ar71xx: register the second ethernet interface on the DB120 board
...
SVN-Revision: 28989
2011-11-12 12:50:19 +00:00
368c6605a0
ar71xx: implement SoC specific phy interface setup
...
SVN-Revision: 28988
2011-11-12 12:50:18 +00:00
21d317b9cc
ar71xx: move phy interface setup into a separate function
...
SVN-Revision: 28987
2011-11-12 12:50:16 +00:00
aff0c84ffa
ar71xx: register both MDIO bus on the DB120 board
...
SVN-Revision: 28986
2011-11-12 12:09:59 +00:00
b144249108
ar71xx: add AR934X specific MDIO registration code
...
SVN-Revision: 28985
2011-11-12 12:09:56 +00:00
f835106c8c
ar71xx: add a secondary mdio bus
...
SVN-Revision: 28984
2011-11-12 12:09:54 +00:00
90a42da270
ar71xx: rename ar71xx_mdio_* structures to ar71xx_mdio0_*
...
SVN-Revision: 28983
2011-11-12 12:09:50 +00:00
9daa2149fd
ar71xx: add an id argument to ar71xx_add_device_mdio
...
SVN-Revision: 28982
2011-11-12 12:09:48 +00:00
b07b687aec
ar71xx: pass netdev and miidev pointer to ar71xx_add_device_dsa
...
SVN-Revision: 28981
2011-11-12 12:09:42 +00:00
a9216bb76e
ar71xx: add AR934x specific USB setup
...
SVN-Revision: 28980
2011-11-12 10:54:20 +00:00
346e44105a
ar71xx: register the first ethernet interface on the DB120 board
...
SVN-Revision: 28979
2011-11-12 10:54:18 +00:00
b1ba5e2f3d
ar71xx: allow to register ethernet interfaces for AR934X
...
SVN-Revision: 28978
2011-11-12 10:54:17 +00:00
2f9e535e89
ar71xx: ag71xx: use fixed link parameters if the mii bus is not registered
...
SVN-Revision: 28977
2011-11-12 10:54:16 +00:00
e962b07c8b
ar71xx: add AR934X specific bootstrap and reset register bits
...
SVN-Revision: 28976
2011-11-12 10:54:15 +00:00
d8db8e94c8
ar71xx: fix GPIO direction setup for AR934x
...
SVN-Revision: 28974
2011-11-12 10:54:09 +00:00
43e993e5f5
ar71xx: fix AR934X clock frequency calculation
...
SVN-Revision: 28973
2011-11-12 10:54:08 +00:00
7a2efd8c28
ar71xx: remove dead code
...
SVN-Revision: 28851
2011-11-08 00:33:20 +00:00
94309039b7
ar71xx: on ar7240, exclude ports from their own port vlan destination mask
...
SVN-Revision: 28850
2011-11-08 00:33:15 +00:00
a801d620a7
ar71xx: add support for the Buffalo WHR-HP-GN board
...
SVN-Revision: 28805
2011-11-07 12:59:10 +00:00
4509af17ed
ar71xx: add support for the Buffalo WHR-G301N board
...
SVN-Revision: 28803
2011-11-07 12:59:07 +00:00
4aace1e2e3
ar71xx: fix WHR-HP-G300N MTD partitions
...
SVN-Revision: 28800
2011-11-07 12:59:03 +00:00
4c985724af
ar71xx: add missing AR71XX_MACH_TL_WR741ND_V4
...
SVN-Revision: 28709
2011-11-01 14:38:12 +00:00
91f08d47c2
ar71xx: add initial support for the TL-WR741ND v4 board
...
The ethernet port LEDs are not working yet.
SVN-Revision: 28706
2011-11-01 11:20:52 +00:00
21e651c9a1
ar71xx: add AR933X GMAC register defines
...
SVN-Revision: 28705
2011-11-01 11:20:50 +00:00
f372620ffa
ar71xx: unify LED names on Planex boards
...
SVN-Revision: 28703
2011-11-01 11:20:47 +00:00
66ab406d5a
ar71xx: unify LED names on Buffalo boards
...
SVN-Revision: 28702
2011-11-01 11:20:46 +00:00
e7586959df
ar71xx: unify LED names on TP-Link boards
...
SVN-Revision: 28701
2011-11-01 11:20:44 +00:00
1646346798
ar71xx: add initial support for the OpenMesh OM2P board
...
Based on a patch by Marek Lindner <marek@open-mesh.com>
SVN-Revision: 28617
2011-10-27 07:54:51 +00:00
d02f22fea1
ar71xx/all0258n: fix partition layout
...
A miscalculation in the original patch makes OpenWrt destroy the failsafe image.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
SVN-Revision: 28615
2011-10-27 07:54:47 +00:00
9d51cda2db
ar71xx: Buffalo WHR-HP-G300N kernel support
...
The initial support for the Buffalo WHR-HP-G300N box.
The code was confirmed to boot and run, but not tested in depth.
Known problem: iw phy phy0 info shows:
Coverage class: 0 (up to 0m)
Available Antennas: TX 0 RX 0
Signed-off-by: Yoichi Shinoda <shinoda@jaist.ac.jp>
SVN-Revision: 28567
2011-10-24 21:49:26 +00:00
d96e321bd1
ar71xx: add kernel support for the Allnet ALL0258N board
...
This patchs adds support for the Allnet ALL0258N outdoor AP/bridge.
The ALL0258N is based on the AR7240 SoC paired with an AR9285 radio,
it got 8MB of NOR and 32MB SDRAM.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
SVN-Revision: 28564
2011-10-24 21:49:21 +00:00
a136b67604
linux: ar71xx: add support for Mikrotik Routerboard RB493G
...
SVN-Revision: 28423
2011-10-11 23:05:16 +00:00
c674c874b7
ag71xx: close a race between the phy state machine and link state
...
A fast stop/start cycle could leave the ag71xx interrupts and tx engine
disabled when using a phy driver with a fixed link and the start/stop
happens between two phy state machine polls.
Prevent this by always forcing the link down on stop regardless of phy
state and having a phy connected.
SVN-Revision: 28380
2011-10-08 11:37:14 +00:00
6ac4156136
ar71xx: fix MAC addresses on the DIR-825-B1 board
...
Patch-by: Lukas Kuna
SVN-Revision: 28295
2011-09-23 19:56:39 +00:00
733399600f
ar71xx: add support for the TP-Link TL-WR703N v1 board
...
Based on a patch by dongyuqi <729650915@qq.com>
SVN-Revision: 28277
2011-09-21 11:47:53 +00:00
d3617ac7d3
ar71xx: add AR933x specific USB setup function
...
SVN-Revision: 28276
2011-09-21 11:47:51 +00:00
91340d8af7
ar71xx: add ar71xx_device_reset_rmw helper
...
SVN-Revision: 28275
2011-09-21 11:47:50 +00:00
079e746fc4
ar71xx: remove 'default [yn]' from machine Kconfig entries
...
SVN-Revision: 28273
2011-09-21 11:47:47 +00:00
73dac07c44
ar71xx: sort AR71XX_MACH_* entries
...
SVN-Revision: 28272
2011-09-21 11:47:45 +00:00
1bdf65f580
ar71xx: fix register range check for DMA stuck checks (thx, Frédéric Moulins)
...
SVN-Revision: 28213
2011-09-11 17:44:12 +00:00
65d809ef19
ar71xx: do not count normal interrupts as spurious ( fixes #10037 )
...
SVN-Revision: 28182
2011-09-06 05:38:23 +00:00
cd2c68501c
ar71xx: fix ethernet PLL setting on ar7242
...
SVN-Revision: 28124
2011-08-29 21:23:46 +00:00
12c84f8eeb
ar71xx: add some code to detect DMA stuck conditions on ar7240
...
SVN-Revision: 27975
2011-08-13 22:30:14 +00:00
85ccc74e1b
ar71xx: on ar724x only reset the link status in the restart handler, the fast reset takes care of DMA stuck issues
...
SVN-Revision: 27973
2011-08-13 21:49:46 +00:00
d26bb6c59c
ar71xx: adjust the mtd layout of tew-632brp and dir-615c to match the image layout ( fixes #9922 )
...
SVN-Revision: 27959
2011-08-11 13:52:40 +00:00
4b75394056
ar71xx: fix ethernet FIFO state corruption on ar7240
...
When starting/stopping DMA sometimes the FIFO state gets corrupted,
leading to wildly fluctuating latencies or packet data corruption.
Fix this by issuing a fast MAC reset as soon as the link is detected
as up. Fixes #9689 , #9405
SVN-Revision: 27896
2011-08-04 17:36:31 +00:00
d2aeca6b6d
ag71xx: fix memory corruption issues on ar7240 on ethernet start/stop
...
When the DMA engine state gets corrupted due to a hardware issues, it
often won't stop rx until a full reset is issued. In that case the hardware
must keep a valid descriptor, otherwise it will write to random places in
system RAM, triggering random crashes. To fix this, keep a dummy descriptor
without a buffer that keeps the DMA engine in a sane state until the reset
is done
SVN-Revision: 27895
2011-08-04 17:36:27 +00:00
500c3a1475
ar71xx: fix MAC/MDIO reset mask handling
...
SVN-Revision: 27894
2011-08-04 17:36:23 +00:00
e18ceb1dac
ar71xx: merge WZR-HP-G301NH support into WZR-HP-G300NH
...
Now that we can use a generic name for the switch there is no need for a
separate image for the WZR-HP-G301NH.
Update the default network config and remove the extra image.
SVN-Revision: 27814
2011-07-28 11:57:51 +00:00
9e4113b493
ar71xx: autodetect rtl8366s/rtl8366rb on wzr-hp-g300nh
...
SVN-Revision: 27756
2011-07-24 14:40:35 +00:00
1afe8a0726
rtl8366: unify rtl8366s and rtl8366rb platform data
...
SVN-Revision: 27754
2011-07-24 14:40:23 +00:00
9105dad418
ar71xx: enable the usb power regulator on the wzr-hp-ag300h through gpio 2 ( #9684 )
...
SVN-Revision: 27739
2011-07-24 08:02:20 +00:00
c7173a211d
ar71xx: reinitialize global switch settings after reset on ar7240
...
SVN-Revision: 27705
2011-07-20 14:39:47 +00:00
ca473833c4
ar71xx: configure address aging on ar7240
...
SVN-Revision: 27704
2011-07-20 14:39:42 +00:00
fefc79f3cb
ar71xx: reset the phy in the ethernet init on ar724x
...
SVN-Revision: 27703
2011-07-20 12:04:34 +00:00
005fe5d1fd
ar71xx: make sure that rx and interrupts are disabled before issuing the hardware reset
...
SVN-Revision: 27702
2011-07-20 12:04:29 +00:00
e7ab000008
ar71xx: increase the delay after the ethernet MAC reset
...
SVN-Revision: 27701
2011-07-20 12:04:25 +00:00
255dcaa3a6
ar71xx: fix an unused variable warning
...
SVN-Revision: 27700
2011-07-20 12:04:20 +00:00
f3d693c0ee
ar71xx: do not reset the hardware on transmit timeout - this would mess up the up the PHY state
...
SVN-Revision: 27568
2011-07-09 06:30:13 +00:00
2806c75c07
ag71xx: keep the rx engine stopped while the link is not up, should hopefully fix stability issues from #9405
...
SVN-Revision: 27567
2011-07-09 06:29:46 +00:00
f9e4619b97
ar71xx: remove CONFIG_MTD_CONCAT ifdefs from the WZR-HP-AG300H code
...
The config option has been removed in 2.6.39.
SVN-Revision: 27320
2011-06-30 12:15:33 +00:00
d98476c6bd
ar71xx: merge 2.6.39 patches
...
Also remove the old UART driver for ar933x.
SVN-Revision: 27314
2011-06-29 08:57:37 +00:00
6627574e57
ar71xx: add 2.6.39 support
...
SVN-Revision: 27310
2011-06-29 08:57:32 +00:00
1e138098cd
ar71xx: remove ar71xx_gpio_irq_set_type
...
SVN-Revision: 27309
2011-06-29 08:57:30 +00:00
055e317ed8
ar71xx: add separate handlers for IP3 interrupts
...
SVN-Revision: 27308
2011-06-29 08:57:29 +00:00
59bff8bf18
ar71xx: use separate handlers for IP2 interrupts
...
SVN-Revision: 27307
2011-06-29 08:57:28 +00:00
9d6af600e1
ar71xx: remove useless irq_desc.status initializations
...
SVN-Revision: 27306
2011-06-29 08:57:27 +00:00
ed7f41792a
ar71xx: bring up secondary radio on wzr-hp-ag300h ( fixes #9608 )
...
SVN-Revision: 27282
2011-06-25 13:48:47 +00:00
e6af77a1c8
ar71xx: cleanup AR933X UART driver
...
SVN-Revision: 27222
2011-06-19 13:17:51 +00:00
066e04d497
ar71xx: fix uart clock frequency for AR933X
...
SVN-Revision: 27221
2011-06-19 13:17:50 +00:00
b7e016ba42
ar71xx: use ar933x_uart.h in the AR933X serial driver
...
SVN-Revision: 27166
2011-06-13 08:12:40 +00:00
b58ede16a5
ar71xx: update early_printk code
...
SVN-Revision: 27165
2011-06-13 08:12:38 +00:00
13363d9129
ar71xx: setup wdt_clock for AR913X to avoid a kernel bug
...
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 27102
2011-06-04 12:30:10 +00:00
ae2cbfa1e8
ar71xx: select the internal antenna by default on the ZCN-1523H boards
...
SVN-Revision: 27101
2011-06-04 12:30:09 +00:00
31dd60689e
Revert "ar71xx: only enable the rx engine after the link is up..."
...
It messes up the DMA state when the link goes down
SVN-Revision: 27088
2011-06-01 18:15:43 +00:00
750af1522b
ar71xx: init external_reset for AR933X
...
SVN-Revision: 27083
2011-06-01 13:12:30 +00:00
af4cae4498
ar71xx: add external_reset field to ath9k_platform_data
...
SVN-Revision: 27082
2011-06-01 13:12:28 +00:00
f0c7b93e5d
ar71xx: init get_mac_revision on AR9330 rev 1
...
SVN-Revision: 27081
2011-06-01 13:12:27 +00:00
1a54e33c17
ar71xx: add get_mac_revision to ath9k_platform_data
...
SVN-Revision: 27080
2011-06-01 13:12:26 +00:00
34ff32a6eb
ar71xx: export SoC revision
...
SVN-Revision: 27079
2011-06-01 13:12:24 +00:00
4f06b8263a
ar71xx: add kernel support for the buffalo wzr-hp-ag300h
...
SVN-Revision: 27075
2011-06-01 02:23:26 +00:00
f332dbd7be
ar71xx: add support for the AP121/AP121-MINI reference boards
...
SVN-Revision: 27067
2011-05-31 22:53:43 +00:00
8beff081eb
ar71xx: register UART for the AR933X SoCs
...
SVN-Revision: 27066
2011-05-31 22:53:42 +00:00
b460bc6f12
ar71xx: add serial driver for the AR933X UART
...
SVN-Revision: 27065
2011-05-31 22:53:40 +00:00
c34e0cbc4c
ar71xx: add WMAC initialization code for the AR933X SoCs
...
SVN-Revision: 27064
2011-05-31 22:53:39 +00:00
e8a0aaf9a2
ar71xx: add ethernet initialization for the AR933X SoCs
...
SVN-Revision: 27063
2011-05-31 22:53:37 +00:00
e0a0f3796a
ar71xx: enable USB support for the AR933x SoCs
...
SVN-Revision: 27062
2011-05-31 22:53:36 +00:00
677c80ee17
ar71xx: add AR933x specific glue for ar71xx_device{start,stop}
...
SVN-Revision: 27061
2011-05-31 22:53:35 +00:00
88c45e3130
ar71xx: the watchdog uses the reference clock on the AR933x SoCs
...
SVN-Revision: 27060
2011-05-31 22:53:34 +00:00
7acbacab8c
ar71xx: add AR933x specific glue code for IRQ initialization
...
SVN-Revision: 27059
2011-05-31 22:53:32 +00:00
e6fde61bec
ar71xx: don't register 8250 UART on the AR933x SoCs
...
SVN-Revision: 27058
2011-05-31 22:53:31 +00:00
8f7541a044
ar71xx: enable GPIO support for the AR933x SoCs
...
SVN-Revision: 27057
2011-05-31 22:53:30 +00:00
e11b9c8371
ar71xx: add AR933x specific frequency initialization code
...
SVN-Revision: 27056
2011-05-31 22:53:29 +00:00
0bf4478d37
ar71xx: add AR933x specific early_printk support
...
SVN-Revision: 27055
2011-05-31 22:53:27 +00:00
6b3ca9ef0b
ar71xx: add preliminary support for the Atheros AR933x SoCs
...
SVN-Revision: 27054
2011-05-31 22:53:26 +00:00
0677e16248
ar71xx: Fix header offset for newer WRT160NL models
...
Newer WRT160NLs have a flash chip with 4K erase blocks instead of 64K,
resulting in miscalculated partition sizes.
Since the actual sizes did not change, hardcode them to their current
sizes, and make sure they are at least one erase block big (in case Cisco
decides to start to use chips with 128K erase blocks).
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 27049
2011-05-31 22:53:20 +00:00
be97e2a043
ar71xx: add SOC_AR{71XX,724X,913X,934X} config symbols
...
SVN-Revision: 27048
2011-05-31 22:53:19 +00:00
5d5f72415e
ar71xx: initialize is_clk_25mhz field for AR9340 WMAC
...
SVN-Revision: 27045
2011-05-31 22:53:15 +00:00
f7b3c3dfd1
ar71xx: sync ath9k_platform_data.h with compat-wireless
...
SVN-Revision: 27044
2011-05-31 22:53:14 +00:00
60d5abbc27
ar71xx: ag71xx: make ring sizes configurable via ethtool
...
SVN-Revision: 27041
2011-05-31 22:53:10 +00:00
7a2651f633
ar71xx: ag71xx: prepare to make ring sizes configurable
...
SVN-Revision: 27040
2011-05-31 22:53:09 +00:00
669aba3871
ar71xx: ag71xx: nuke unused AG71XX_TX_FIFO_LEN define
...
Reported-by: Dave Täht <dave.taht@gmail.com>
SVN-Revision: 27039
2011-05-31 22:53:07 +00:00
2b5402d128
ar71xx: only enable the rx engine after the link is up, fixes a race condition that got rx stuck when the interface is brought up during lots of inbound traffic (thx, matteo)
...
SVN-Revision: 27035
2011-05-30 23:08:01 +00:00
0ebc93831f
ar71xx: disable flow control for ar724x, it can get stuck in a loop of continously sending MAC pause frames
...
SVN-Revision: 27034
2011-05-30 23:07:57 +00:00
17e257925f
ar71xx: don't probe the LAN PHY
...
SVN-Revision: 26924
2011-05-17 11:15:24 +00:00
4deecea26b
ar71xx: detect link on LAN ports
...
SVN-Revision: 26922
2011-05-17 11:12:56 +00:00
2ea528d1d0
ar71xx: add link detection on Ubiquiti devices WAN port
...
SVN-Revision: 26891
2011-05-14 23:31:50 +00:00
c0c2e18452
use correct macros and frame size in ag71xx
...
SVN-Revision: 26890
2011-05-14 23:10:06 +00:00
99d1d4f795
ar71xx: cosmetic fixes
...
SVN-Revision: 26889
2011-05-14 23:08:00 +00:00
9b5036a29d
ar71xx: populate LED3 on the JA76PF board
...
Patch-by: Cezary Jackiewicz <cezary@eko.one.pl>
SVN-Revision: 26862
2011-05-08 21:38:51 +00:00
869f3cb718
ar71xx: remove superfluous fifo_cfg overrides
...
SVN-Revision: 26859
2011-05-08 21:38:46 +00:00
5d77f370d6
ar71xx: ag71xx: make switch register access atomic
...
Reading of the PHY registers occasionally returns with bogus values
under heavy load. This misleads the PHY driver and thus causes false
link/speed change notifications which leads to performance loss.
This is easily noticable during an iperf session:
...
[ 3] 52.0-53.0 sec 11.3 MBytes 94.4 Mbits/sec
[ 3] 53.0-54.0 sec 11.4 MBytes 95.4 Mbits/sec
eth1: link down
br-lan: port 2(eth1) entering forwarding state
eth1: link up (100Mbps/Full duplex)
br-lan: port 2(eth1) entering forwarding state
br-lan: port 2(eth1) entering forwarding state
[ 3] 54.0-55.0 sec 6.75 MBytes 56.6 Mbits/sec
[ 3] 55.0-56.0 sec 0.00 Bytes 0.00 bits/sec
[ 3] 56.0-57.0 sec 10.5 MBytes 88.1 Mbits/sec
...
[ 3] 169.0-170.0 sec 11.4 MBytes 95.4 Mbits/sec
[ 3] 170.0-171.0 sec 11.4 MBytes 95.4 Mbits/sec
eth1: link up (10Mbps/Half duplex)
[ 3] 171.0-172.0 sec 7.63 MBytes 64.0 Mbits/sec
[ 3] 172.0-173.0 sec 9.38 MBytes 78.6 Mbits/sec
eth1: link up (100Mbps/Full duplex)
[ 3] 173.0-174.0 sec 11.3 MBytes 94.4 Mbits/sec
[ 3] 174.0-175.0 sec 11.4 MBytes 95.4 Mbits/sec
SVN-Revision: 26856
2011-05-08 16:32:53 +00:00
3711658281
ar71xx: ag71xx: fix section mismatch warnings
...
The function __devinit ag71xx_probe() references
a function __devexit ag71xx_phy_disconnect().
This is often seen when error handling in the init function
uses functionality in the exit path.
The fix is often to remove the __devexit annotation of
ag71xx_phy_disconnect() so it may be used outside an exit section.
The function ag71xx_phy_disconnect() references a function in an exit
section.
Often the function ag71xx_ar7240_cleanup() has valid usage outside the
exit section
and the fix is to remove the __devexit annotation of
ag71xx_ar7240_cleanup.
SVN-Revision: 26855
2011-05-08 13:30:36 +00:00
ef53029870
ar71xx: ag71xx: fix build error if debugfs is enabled
...
SVN-Revision: 26854
2011-05-08 13:30:26 +00:00
8b67d748cb
ar71xx: ag71xx: add debugfs entry for [rt]x_ring
...
SVN-Revision: 26845
2011-05-07 12:40:34 +00:00
2166432ba0
ar71xx: ag71xx: add timestamps to ag71xx_buf
...
SVN-Revision: 26844
2011-05-07 12:40:28 +00:00
896e1d1ab4
ar71xx: ag71xx: use dynamically allocated buffer for napi_stats
...
SVN-Revision: 26843
2011-05-07 12:40:26 +00:00
a6708d20d1
ar71xx: ag71xx: use debugfs_remove_recursive
...
SVN-Revision: 26842
2011-05-07 12:40:25 +00:00
c39e5b9360
ar71xx: override wmac device name for the AR934x SoCs
...
SVN-Revision: 26840
2011-05-07 09:23:32 +00:00
cbc75a9c70
ar71xx: use the ar8316 switch driver on the PB92 board and add a matching default network config
...
SVN-Revision: 26779
2011-04-28 21:27:42 +00:00
36aecb08b8
ar71xx: fix MDIO access on ar7242 (based on a patch by Jess Zhu)
...
SVN-Revision: 26777
2011-04-28 19:30:49 +00:00
fa9f45f345
ar71xx: fix build error w/o CONFIG_PCI
...
SVN-Revision: 26606
2011-04-12 13:14:56 +00:00
e193547733
ar71xx: use the gpio_keys_polled driver instead of gpio_buttons
...
SVN-Revision: 26603
2011-04-12 09:29:21 +00:00
54ede24829
ar71xx: Add support for WZR-HP-G301NH
...
Add support for the Buffalo WZR-HP-G301NH. The only difference between it
and the WZR-HP-G00NH is that it has a RTL8366RB instead of a RTL8366S.
Since we don't do runtime detection of the switch, we need a separate
machine definition for it.
While we are at it, also rename the profile to reflect that it now is for
more than one device.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 26601
2011-04-12 09:29:10 +00:00
ef4c1d49a6
ar71xx: merge dev-ar9{13,34}x-wmac into dev-ar9xxx-wmac
...
SVN-Revision: 26595
2011-04-11 17:37:08 +00:00
4711dea8ff
ar71xx: fix AR934X_WMAC_SIZE
...
SVN-Revision: 26594
2011-04-11 17:37:03 +00:00
8586e61b00
ar71xx: fix section mismatch
...
SVN-Revision: 26562
2011-04-09 18:47:55 +00:00
a8bf5e3cdb
ar71xx: rename ar934x_ref_freq to ar71xx_ref_freq
...
Also initialize that for each SoC and print its value along with the
other frequencies.
SVN-Revision: 26561
2011-04-09 18:47:52 +00:00
5573d6eb28
ar71xx: show the SoC type earlier
...
SVN-Revision: 26560
2011-04-09 18:47:50 +00:00
ab4c3b3a1c
ar71xx: cleanup SoC detection code
...
SVN-Revision: 26559
2011-04-09 18:47:49 +00:00
3310c70702
ar71xx: Fix mac address offset for AR934x
...
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
SVN-Revision: 26557
2011-04-09 18:47:42 +00:00
8f889f9250
ar71xx: add DB120 board specific PCI initialization
...
Signed-off-by: Jaiganesh Narayanan <jnarayanan@atheros.com>
SVN-Revision: 26523
2011-04-07 20:53:41 +00:00
a0c3d49064
ar71xx: register WMAC device on the DB120 board
...
Signed-off-by: Jaiganesh Narayanan <jnarayanan@atheros.com>
SVN-Revision: 26522
2011-04-07 20:53:37 +00:00
428888faec
ar71xx: add support for the built-in WMAC of the AR934x
...
Signed-off-by: Jaiganesh Narayanan <jnarayanan@atheros.com>
SVN-Revision: 26521
2011-04-07 20:53:34 +00:00
14b42c44ec
ar71xx: add initial support for the Atheros DB120 board
...
Signed-off-by: Jaiganesh Narayanan <jnarayanan@atheros.com>
SVN-Revision: 26518
2011-04-07 20:53:19 +00:00
2b064bb398
ar71xx: add support for the watchdog of the AR934x SoCs
...
Signed-off-by: Jaiganesh Narayanan <jnarayanan@atheros.com>
SVN-Revision: 26516
2011-04-07 20:53:10 +00:00
e4555809c7
ar71xx: enable PCI for the AR934[24] SoCs
...
Signed-off-by: Jaiganesh Narayanan <jnarayanan@atheros.com>
SVN-Revision: 26515
2011-04-07 20:53:05 +00:00
4f395745af
ar71xx: enable USB support for the AR934x SoCs
...
Signed-off-by: Jaiganesh Narayanan <jnarayanan@atheros.com>
SVN-Revision: 26514
2011-04-07 20:53:03 +00:00
25693b4769
ar71xx: enable GPIO support for the AR934x SoCs
...
Signed-off-by: Jaiganesh Narayanan <jnarayanan@atheros.com>
SVN-Revision: 26513
2011-04-07 20:53:00 +00:00
334a5ec36e
ar71xx: add AR934x specific glue for ar7100_device{start,stop}
...
Signed-off-by: Jaiganesh Narayanan <jnarayanan@atheros.com>
SVN-Revision: 26512
2011-04-07 20:52:57 +00:00
ccd3ebd309
ar71xx: add AR934x specific UART clock initialization
...
Signed-off-by: Jaiganesh Narayanan <jnarayanan@atheros.com>
SVN-Revision: 26511
2011-04-07 20:52:53 +00:00
91470edada
ar71xx: add AR934x specific glue for IRQ initialization
...
Signed-off-by: Jaiganesh Narayanan <jnarayanan@atheros.com>
SVN-Revision: 26510
2011-04-07 20:52:49 +00:00
3b209880bc
ar71xx: add initial support for the AR934x SoCs
...
Signed-off-by: Jaiganesh Narayanan <jnarayanan@atheros.com>
SVN-Revision: 26509
2011-04-07 20:52:45 +00:00
98c78c13db
ar71xx: enable access to the WAN port PHY on a few devices, adds WAN link detection
...
SVN-Revision: 26394
2011-04-02 00:47:33 +00:00
41ee4a283c
ar71xx: only allow internal access to the ar7240 switch, export the MDIO bus behind the switch instead
...
SVN-Revision: 26393
2011-04-02 00:47:29 +00:00
acbb3e50e7
ar71xx: frequent ethernet mac resets upset the MDIO bus on ar7240, so do not run them on every device open, only on tx timeouts
...
SVN-Revision: 26392
2011-04-02 00:47:25 +00:00
8eb616de82
ar71xx: add support for the TP-Link TL-WA901ND v2 board
...
Patch-by: Jonathan Benett <jbscience87@gmail.com>
SVN-Revision: 26119
2011-03-13 15:08:31 +00:00
5bddd70a37
Revert "ar71xx: add missing gpio_set_debounce function" - wrong target
...
SVN-Revision: 25854
2011-03-03 16:21:23 +00:00
57a14f4e15
ar71xx: add missing gpio_set_debounce function
...
SVN-Revision: 25848
2011-03-03 10:33:35 +00:00
256169cbd0
ar71xx: add rtl8366s initvals for the DIR-825 board
...
SVN-Revision: 25121
2011-01-26 20:35:47 +00:00
67c3e0bf7e
ar71xx: add support for the WNDR3700v2 board
...
Based on a patch by Mark Mentovai <mark@moxienet.com>
SVN-Revision: 25118
2011-01-26 20:35:42 +00:00
18ed5bca9b
fix null pointer access in mach-dir-600-a1.c machine setup ( #8671 )
...
SVN-Revision: 25043
2011-01-18 18:04:50 +00:00
b67bbfe287
ar71xx: fix wlan LED on the TL-WR741 board
...
* Patch from #8630
SVN-Revision: 24963
2011-01-11 08:20:47 +00:00
dd53effe15
ar71xx: fix wrong names of the WPS LED/button
...
Reported-by: Nuno Gonçalves
SVN-Revision: 24961
2011-01-10 18:15:47 +00:00
23a6173099
ar71xx: use gpio_*_cansleep calls in the rb4xx NAND driver
...
SVN-Revision: 24944
2011-01-09 09:29:45 +00:00
0de8689b70
ar71xx: use spinlock in ar71xx_device_{start,stop}
...
SVN-Revision: 24929
2011-01-08 11:28:32 +00:00
6acfae9379
ar71xx: enable ar7240 switch support on the UBNT NanoStation M Fixes broadcast frames on the second ethernet MAC
...
Signed-off-by: Alexander Couzens <lynxis@c-base.org>
SVN-Revision: 24723
2010-12-19 11:56:42 +00:00
cafe08a1b2
ar71xx: remove stray semicolons
...
SVN-Revision: 24651
2010-12-17 17:57:20 +00:00
01c76bf128
ar71xx: fix WLAN LEDs on the DIR-825 board
...
SVN-Revision: 24650
2010-12-17 17:10:21 +00:00
c1d3a23d19
ar71xx: add helper function to setup ath9k LED/GPIO on the AP94 based boards
...
SVN-Revision: 24649
2010-12-17 17:10:19 +00:00
8390b7dc9b
ar71xx: UBNT Secondary MAC address duplicate fix
...
There is Secondary MAC address duplicate problem with some UBNT
RouterStation and RouterStation Pro HW batches as Primary MAC addresses
are not increased by 2 per device in board data. Fix is to use 'Locally
Administrated bit' for Secondary MAC address instead of increasing
Primary MAC addresses by 1 which could overlap with other device
Primary MAC address.
Signed-off-by: Kestutis Barkauskas<keba@devint.net>
SVN-Revision: 24643
2010-12-17 17:10:01 +00:00
a2a5598c00
ar71xx: add wlan led for the TL-WR941ND
...
SVN-Revision: 24612
2010-12-15 19:55:50 +00:00
e421d2575f
ar71xx: UBNT M-Series MAC address fix
...
UBNT M-Series devices have 2 MAC addresses in board data.
Fix is to use both entries from board data instead of one entry.
Signed-off-by: Kestutis Barkauskas<keba@devint.net>
SVN-Revision: 24611
2010-12-15 19:55:47 +00:00
Gabor Juhos
Felix Fietkau
Jo-Philipp Wich
Jonas Gorski
Matteo Croce