The GPIO buttons of ARV752DPW are active low.
Treating them as active high caused a reboot loop as a reset-button
press is detected by gpio-button-hotplug/gpio-keys-polled on startup.
This fixes: https://dev.openwrt.org/ticket/12642
Signed-off-by: Rafael Gieschke <rafael@gieschke.de>
SVN-Revision: 36783
On linux 3.8 the switch is named as "switch0", but the network configuration script names it as "eth0", causing no communication over ethernet due to no proper VLAN config.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 36782
This requires all the preceding patches and finishes support for the
DGN3500, also removing an obsolete file.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
SVN-Revision: 36781
This patch is a device tree enhancement that IMHO is worthy of mainline.
It allows the bootloader's commandline to be preserved even when the
device tree specifies one.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
SVN-Revision: 36780
This patch enables retrieving the wifi calibration data from an MTD
partition. It requires the previous patch.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
SVN-Revision: 36779
This postpones the initialization of PCI and wifi until after the MTD
initialization, so that calibration data may be loaded from there.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
SVN-Revision: 36778
This reassigns the PPPoE status to the LED that was intended to indicate
it, rather than the DSL sync light.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
SVN-Revision: 36777
* add support for rcS
* logread can relay log via tcp
* make sure directories are created before mknod is called
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 36776
- allows building without IPv6 support
- uses more robust rules to cope with missing libext.a
- uses better linking strategy to avoid symbol clashes with older iptables
- introduces source compatiblity layer for different libxtables versions
SVN-Revision: 36736
At offset 0x40, signature for TL-MR10U/TL-MR11U begin
from 0x00, not 0x10/0x11.
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36727
MR10U is closer to MR3040 than WR703N. This changes also
enable USB power on GPIO18.
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 36726
- allows symbolic notation for src_ip, src_dip and dest_ip options, e.g. option src_ip 'lan' to automatically resolve to "192.168.1.0/24"
- automatically infer destination zone for redirects from target ip, this makes 'dest' optional and nat reflection setup more robust
- properly support output rules with dest '*' to hook directly into delegate_output
- fixes crash when processing rules with unresolved targets
SVN-Revision: 36721
Tested on Buffalo WZR-600DHP with ar8316 switch. Commands used to mirror both
RX and TX traffic from LAN port 1 to LAN port 4:
$ swconfig dev switch0 set enable_mirror_rx 1
$ swconfig dev switch0 set enable_mirror_tx 1
$ swconfig dev switch0 set mirror_monitor_port 4
$ swconfig dev switch0 set mirror_source_port 1
Signed-off-by: Colin Leitner <colin.leitner@googlemail.com>
Tested-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 36713
- Use weak references for instantiating libext*.a matches, makes fw3 independant from the compile time features of iptables
- Do not leak memory when processing rules with unknown targets or matches
SVN-Revision: 36698
Gabor Juhos
John Crispin
Steven Barth
Felix Fietkau
Jo-Philipp Wich
Luka Perkov