Make wpan depend on not kernel 3.18 so it will get activated on all
other kernel versions like 4.0 and 4.1.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 46276
Internal GPIO pins are used for PoE passthrough setups in multi-port
routers. This patch implemnets control over this hardware feature for
Ubiquiti Nanostations and TP-Link CPE510.
Signed-off-by: Lars Kruse <lists@sumpfralle.de>
SVN-Revision: 46271
This reverts commit r45579.
With the latest change r46251 ("nvram: fix "Segmentation fault" caused
by setting memory out of buffer") nvram utility shouldn't crash anymore.
It was tested on 3 brcm47xx devices:
1) Unknown with 0x10000 NVRAM size (0x8000 offset)
2) Linksys E1000 V2.1 with 0x10000 (0x8000 offset)
3) Linksys WRT300N V1 with 0x10000 (0x8000 offset)
And 3 bcm53xx devices:
1) Buffalo WZR-600DHP2 with 0x160000 NVRAM size
2) Buffalo WZR-1750DHP with 0x10000 NVRAM size
3) Netgear R6250 V1 with 0x180000 NVRAM size
(all using 0 offset)
This is an important change as it allows reading whole NVRAM. This may
critical when reading some basic configuration (e.g. switch ports).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 46253
Some MTD partitions with NVRAM have content starting in the middle. In
such case offset is set and nvram_header returns pointer to the middle.
It means we have to respect offset when calculating remaining space.
By the way use real MTD partition size (nvram_part_size variable) as we
may want to bump NVRAM_SPACE in the (very near) future.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 46251
This patch adds support for the Cisco WAP4410N, an access point that uses the
AR9132 SoC. Web upgrades from stock are not yet possible, UART access required
for the initial flash.
Signed-off-by: Ryan A Young <rayoung@utexas.edu>
SVN-Revision: 46250
The mips reloc patch introduced new allocations which were done before
add_unformed_module but never freed them in case of an error. A new hook in
Linux 3.19 called module_arch_freeing_init can be used for freeing memory
which were allocated during this init phase.
The problem can be seen when trying to load a module (via busybox insmod)
when it was already loaded.
free -m
for i in `seq 1 100`; do
/sbin/insmod /lib/modules/*/ath9k.ko >& /dev/null
done
free -m
This simple loop would leak ~3.2 MB.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 46247
Ath10k has now a proper method of providing calibration data via
the kernel firmware API. This patch can be dropped as all boards
now use the proper method.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 46245
Currently one board uses the "proper" way of providing firmware
with the name ath10k/cal-pci-<pci address>.bin, whereas other
boards patch board.bin template in preinit and rely on a custom
ath10k patch to use calibration data from the template.
This patch makes all boards use the first method.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 46244
This changes makes it possible to store custom settings
in individual files inside the directory /etc/sysctl.d/.
Signed-off-by: Stefan Tomanek <stefan.tomanek+openwrt@wertarbyte.de>
SVN-Revision: 46239
This device is identical to the TL-WR740N v5, it even uses the same HWID (which
wasn't the case for older TL-WR741ND revisions).
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 46238
Backport for the Spansion S25FL164K
It's a 8 MiB flash chip with 4 KiB erase sectors.
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
SVN-Revision: 46237
This patch adds support for the Bitmain Antminer S3 Cryptocurrency Miner
http://wiki.openwrt.org/toh/bitmain/s3
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
SVN-Revision: 46236
rocket-m titanium is a device based on ar9344 with 802.11af poe.
It doesn't use the SoC wifi, instead it's using an ar9280 connected to
the pci bus. The gps version of the rocket-m ti is working, but
gps is untested. The gps is connected to the first serial port.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 46234
Add features ext4 targz to target x86/xen_domu in order to
generate images in defconfig.
This fixes#18074.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
SVN-Revision: 46233
Basically the only error I am seeing is "Correctable Error". Also newer
lantiq PCIe drivers have this message wrapped in a "if debug enabled"
block. So it should be safe to disable this warning.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 46222
Rafał Miłecki
Hauke Mehrtens
Felix Fietkau
John Crispin
Steven Barth