Commit Graph

127 Commits (31697f92a25f8a6700978eedc658cadaacd2e5f2)

Author SHA1 Message Date
Adrian Schmutzler 0130022bae ath79: split base-files into subtargets
While most of the target's contents are split into subtargets, the
base-files are maintained for the target as a whole.

However, OpenWrt already implements a mechanism that will use (and
even prefer) files in the subtargets' directories. This can be
exploited to make several scripts subtarget-specific and thus save
some space (especially helpful for the tiny devices).

The only script remaining in parent base-files is
/etc/hotplug.d/ieee80211/00-wifi-migration, everything else is
moved/split.

Note that this will increase overall code lines, but reduce code
per subtarget.

base-files ipk size reduction:
master (generic)   49135 B
split (generic)    48533 B (- 0.6 kiB)
split (tiny)       43337 B (- 5.7 kiB)
split (nand)       44423 B (- 4.6 kiB)

Tested on TL-WR1043ND v4 (generic) and TL-WR841N v12 (tiny).

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-27 14:24:22 +01:00
André Valentin 99835e0999 ath79: add support for ZyXEL NBG6716
Attention: Kernel partition size has been enlarged to 4MB.
To switch, you must update to latest ar71xx-nand snapshort and flash the
sysupgrade-4M-Kernel.bin:

zcat openwrt-ath79-nand-zyxel_nbg6716-squashfs-sysupgrade-4M-Kernel.bin | mtd -r -e ubi write - firmware; reboot -f
You will end up with a fresh config if you do not inject config into the image.

The NBG6716 may come with 128MB or 256MB NAND. ar71xx was able to use all, but
ath79 can only use the first 128MB. Therefore the complete NAND needs to be
overwritten. If not, the old UBI may make problems and lead to reboot loop.

Access the real u-boot shell:
ZyXEL uses a proprietary loader/shell on top of u-boot: "ZyXEL zloader v2.02"
When the device is starting up, the user can enter the the loader shell
by simply pressing a key within the 3 seconds once the following string
appears on the serial console:

|   Hit any key to stop autoboot:  3

The user is then dropped to a locked shell.

|NBG6716> HELP
|ATEN    x[,y]     set BootExtension Debug Flag (y=password)
|ATSE    x         show the seed of password generator
|ATSH              dump manufacturer related data in ROM
|ATRT    [x,y,z,u] RAM read/write test (x=level, y=start addr, z=end addr, u=iterations)
|ATGO              boot up whole system
|ATUR    x         upgrade RAS image (filename)
|NBG6716>

In order to escape/unlock a password challenge has to be passed.
Note: the value is dynamic! you have to calculate your own!

First use ATSE $MODELNAME (MODELNAME is the hostname in u-boot env)
to get the challange value/seed.

|NBG6716> ATSE NBG6716
|012345678901

This seed/value can be converted to the password with the help of this
bash script (Thanks to http://www.adslayuda.com/Zyxel650-9.html authors):

- tool.sh -
ror32() {
  echo $(( ($1 >> $2) | (($1 << (32 - $2) & (2**32-1)) ) ))
}
v="0x$1"
a="0x${v:2:6}"
b=$(( $a + 0x10F0A563))
c=$(( 0x${v:12:14} & 7 ))
p=$(( $(ror32 $b $c) ^ $a ))
printf "ATEN 1,%X\n" $p
- end of tool.sh -

|# bash ./tool.sh 012345678901
|
|ATEN 1,879C711

copy and paste the result into the shell to unlock zloader.

|NBG6716> ATEN 1,0046B0017430

If the entered code was correct the shell will change to
use the ATGU command to enter the real u-boot shell.

|NBG6716> ATGU
|NBG6716#

Signed-off-by: André Valentin <avalentin@marcant.net>
2019-10-27 13:38:49 +01:00
Adrian Schmutzler 8c36fd3105 ath79: apply alphabetical sorting to entries in 10_fix_wifi_mac
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-21 14:22:47 +02:00
Adrian Schmutzler 244745d7fc ath79: remove empty default case in 10_fix_wifi_mac
This removes a useless empty default case.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-21 14:22:33 +02:00
Adrian Schmutzler 44da2e0344 ath79: fix whitespaces in 10_fix_wifi_mac
This converts leading whitespaces to tabs and removes a double
newline at the end of the file.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-21 14:22:19 +02:00
Adrian Schmutzler 6b53033783 ath79: fix patching ath9k MAC address for MyNet WiFi Range Extender
The code line patching ath9k MAC address for this device contains
a wrong number of arguments including an unset "$mac", which
looks like a typo or copy/paste mistake.

This has been introduced already in the device support commit
745dee11ac ("ath79: add support for WD My Net Wi-Fi Range
Extender").

This patch just removes the "$mac" argument, leaving a formally
valid line. (No on-device test has been performed.)

Cc: Christian Lamparter <chunkeey@gmail.com>

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-21 13:20:24 +02:00
Michal Cieslakiewicz 09f46c6b54 ath79: add support for Netgear WNR1000 v2
This patch adds ath79 support for Netgear WNR1000v2.
Router was previously supported by ar71xx target only.
Note: this is a 4_32 device with limited upgrade capabilities.

Specification
=============
  * Description: Netgear WNR1000 v2
  * Loader: U-boot
  * SOC: Atheros AR7240 (340 MHz)
  * RAM: 32 MiB
  * Flash: 4 MiB (SPI NOR)
	- U-boot binary: 256 KiB
	- U-boot environment: 64 KiB
	- Firmware: 3712 KiB
	- ART: 64 KiB
  * Ethernet: 4 x 10/100 LAN + 1 x 10/100 WAN
  * Wireless: 2.4 GHz b/g/n (Atheros AR9285)
  * USB: no
  * Buttons:
	- Reset
	- WiFi (rfkill)
	- WPS
  * LEDs:
	- Power (amber/green)
	- WAN (amber/green)
	- WLAN (blue)
	- 4 x LAN (amber/green)
	- WPS (green)
  * UART: 4-pin connector JP2, 3.3V (Vcc, TX, RX, GND), 115200 8N1
  * Power supply: DC 12V 1A
  * MAC addresses: LAN on case label, WAN +1, WLAN +2

Installation
============
  * TFTP recovery
  * TFTP via U-boot prompt
  * sysupgrade
  * Web interface

Test build configuration
========================
CONFIG_TARGET_ath79=y
CONFIG_TARGET_ath79_tiny=y
CONFIG_TARGET_ath79_tiny_DEVICE_netgear_wnr1000-v2=y
CONFIG_ALL_KMODS=y
CONFIG_DEVEL=y
CONFIG_CCACHE=y
CONFIG_COLLECT_KERNEL_DEBUG=y
CONFIG_IMAGEOPT=y
CONFIG_KERNEL_DEBUG_INFO=y
CONFIG_KERNEL_DEBUG_KERNEL=y

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
2019-10-21 13:15:46 +02:00
Michal Cieslakiewicz 12719ce37a ath79: add support for Netgear WNR2000 v3
This patch adds ath79 support for Netgear WNR2000v3.
Router was previously supported by ar71xx target only.
Note: this is a 4_32 device with limited upgrade capabilities.

Specification
=============
  * Description: Netgear WNR2000 v3
  * Loader: U-boot
  * SOC: Atheros AR7241 (360 MHz)
  * RAM: 32 MiB
  * Flash: 4 MiB (SPI NOR)
	- U-boot binary: 256 KiB
	- U-boot environment: 64 KiB
	- Firmware: 3712 KiB
	- ART: 64 KiB
  * Ethernet: 4 x 10/100 LAN + 1 x 10/100 WAN
  * Wireless: 2.4 GHz b/g/n (Atheros AR9287)
  * USB: no
  * Buttons:
	- Reset
	- WiFi (rfkill)
	- WPS
  * LEDs:
	- Power (amber/green)
	- WAN (amber/green)
	- WLAN (blue)
	- 4 x LAN (amber/green)
	- WPS (green)
  * UART: 4-pin connector JP1, 3.3V (Vcc, TX, RX, GND), 115200 8N1
  * Power supply: DC 12V 1A
  * MAC addresses: LAN on case label, WAN +1, WLAN +2

Installation
============
  * TFTP recovery
  * TFTP via U-boot prompt
  * sysupgrade
  * Web interface

Test build configuration
========================
CONFIG_TARGET_ath79=y
CONFIG_TARGET_ath79_tiny=y
CONFIG_TARGET_ath79_tiny_DEVICE_netgear_wnr2000-v3=y
CONFIG_ALL_KMODS=y
CONFIG_DEVEL=y
CONFIG_CCACHE=y
CONFIG_COLLECT_KERNEL_DEBUG=y
CONFIG_IMAGEOPT=y
CONFIG_KERNEL_DEBUG_INFO=y
CONFIG_KERNEL_DEBUG_KERNEL=y

Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
2019-10-21 13:15:19 +02:00
Tomasz Maciej Nowak 1bc921f419 ath79: add support for Sitecom WLR-7100
Sitecom WLR-7100 v1 002 (marketed as X7 AC1200) is a dual band wireless
router.

Specification
SoC: Atheros AR1022
RAM: 64 MB DDR2
Flash: 8 MB SPI NOR
WIFI: 2.4 GHz 2T2R integrated
      5 GHz 2T2R QCA9882 integrated (connected to PCIe lane)
Ethernet: 5x 10/100/1000 Mbps QCA8337N
USB: 1x 2.0
LEDS: 4x GPIO controlled, 5x switch
Buttons: 2x GPIO controlled
UART: row of 4 unpopulated holes near USB port, starting count from
      white triangle on PCB
      1. VCC 3.3V, 2. GND, 3. TX, 4. RX
      baud: 115200, parity: none, flow control: none

Installation
1. Connect to one of LAN (yellow) ethernet ports,
2. Open router configuration interface,
3. Go to Toolbox > Firmware,
4. Browse for OpenWrt factory image with dlf extension and hit Apply,
5. Wait few minutes, after the Power LED will stop blinking, the router
   is ready for configuration.

Known issues
5GHz LED doesn't work

Additional information
When TX line on UART is connected, and board is switched on from power
off state, the DDR memory training may fail.
If connected to UART, when prompted for number on boot, one can enter
number 4 to open bootloader (U-Boot) command line.
OEM firmware shell password is: SitecomSenao
useful for creating backup of original firmware.
There is also another revision of this device (v1 001), which may or may
not work with introduced images.

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
2019-10-21 13:01:10 +02:00
Adrian Schmutzler 48b5d08a48 treewide: use a single ath10k MAC patching function with checksum
While all ath10k eeproms have a checksum field, so far two
functions for patching ath10k MAC address have been present (and
been used).

This merges code to provide a single function ath10k_patch_mac
in caldata.sh, having its name in accordance with ath9k functions.
By doing so, correct MAC patching for current and future ath10k
devices should be ensured.

This patch adds checksum adjustments for several targets on
ath79 and lantiq.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-15 18:13:54 +02:00
Andreas Ziegler 07c1ddf522 ath79: add support for UniFi AC-LR
The Unifi AC-LR has identical hardware to the Unifi AC-Lite.
The antenna setup is different according to the vendor,
which explains the thicker enclosure.

Therefore, it is helpful to know the exact device variant,
instead of having "Ubiquiti UniFi-AC-LITE/LR".

Signed-off-by: Andreas Ziegler <dev@andreas-ziegler.de>
[fix legacy name in commit message; add old boardname to
SUPPORTED_DEVICES]
Signed-off-by: David Bauer <mail@david-bauer.net>
2019-10-15 18:13:54 +02:00
Adrian Schmutzler 2c60de0e3f treewide: move MAC address patch functions to common library
This unifies MAC address patch functions and moves them to a
common script. While those were implemented differently for
different targets, they all seem to do the same. The number of
different variants is significantly reduced by this patch.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-14 12:36:02 +02:00
Adrian Schmutzler 5b6a809092 treewide: move calibration data extraction function to library
This moves the almost identical calibration data extraction
functions present multiple times in several targets to a single
library file /lib/functions/caldata.sh.

Functions are renamed with more generic names to merge different
variants that only differ in their names.

Most of the targets used find_mtd_chardev, while some used
find_mtd_part inside the extraction code. To merge them, the more
abundant version with find_mtd_chardev is used in the common code.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[rebase on latest master; add mpc85xx]
Signed-off-by: David Bauer <mail@david-bauer.net>
2019-10-13 21:48:58 +02:00
Adrian Schmutzler c1388a2deb base-files: move xor() from caldata extraction to functions.sh
The xor() function is defined in each of the caldata extraction
scripts for several targets. Move it to functions.sh to reduce
duplicate code.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-10-13 19:03:57 +02:00
Roger Pueyo Centelles bba6646b5c ath79: add support for COMFAST CF-E313AC
This patch adds support for the COMFAST CF-E313AC, an  outdoor wireless
CPE with two Ethernet ports and a 802.11ac radio.

Specifications:

 - QCA9531 SoC
 - 650/400/216 MHz (CPU/DDR/AHB)
 - 1x 10/100 Mbps WAN Ethernet, 48V PoE-in
 - 1x 10/100 Mbps LAN Ethernet, pass-through 48V PoE-out
 - 1x manual pass-through PoE switch
 - 64 MB RAM (DDR2)
 - 16 MB FLASH
 - QCA9886 2T2R 5 GHz 802.11ac, 23 dBm
 - 12 dBi built-in antenna
 - POWER/LAN/WAN/WLAN green LEDs
 - 4x RSSI LEDs (2x red, 2x green)
 - UART (115200 8N1)

Flashing instructions:

 The original firmware is based on OpenWrt so a sysupgrade image can be
 installed via the stock web GUI. Settings from the original firmware
 will be saved and restored on the new one, so a factory reset will be
 needed. To do so, once the new firmware is flashed, enter into failsafe
 mode by pressing the reset button several times during the boot
 process, while the WAN LED flashes, until it starts flashing faster.
 Once in failsafe mode, perform a factory reset as usual.

 Alternatively, the U-boot bootloader contains a recovery HTTP server
 to upload the  firmware. Push the reset button while powering the
 device on and keep it pressed for >10 seconds. The device's LEDs will
 blink several times and the recovery page will be at
 http://192.168.1.1; use it to upload the sysupgrade image.

Note:

 Four MAC addresses are stored in the "art" partition (read-only):
  - 0x0000: 40:A5:EF:AA:AA:A0
  - 0x0006: 40:A5:EF:AA:AA:A2
  - 0x1002: 40:A5:EF:AA:AA:A1
  - 0x5006: 40:A5:EF:AA.AA:A3 (inside the 5 GHz calibration data)

 The stock firmware assigns MAC addresses to physical and virtual
 interfaces in a very particular way:
  - eth0 corresponds to the physical Ethernet port labeled as WAN
  - eth1 corresponds to the physical Ethernet port labeled as LAN

  - eth0 belongs to the bridge interface br-wan
  - eth1 belongs to the bridge interface br-lan

  - eth0 is assigned the MAC from 0x0 (*:A0)
  - eth1 is assigned the MAC from 0x1002 (*:A1)

  - br-wan is forced to use the MAC from 0x1002 (*:A1)
  - br-lan is forced to use the MAC from 0x0 (*:A0)

  - radio0 uses the calibration data from 0x5000 (which contains
    a valid MAC address, *:A3). However, it is overwritten by the
    one at 0x6 (*:A2)

 This commit preserves the LAN/WAN roles of the physical Ethernet
 ports (as labeled on the router) and the MAC addresses they expose
 by default (i.e., *:A0 on LAN, *:A1 on WAN), but swaps the position
 of the eth0/eth1 compared to the stock firmware:
  - eth0 corresponds to the physical Ethernet port labeled as LAN
  - eth1 corresponds to the physical Ethernet port labeled as WAN

  - eth0 belongs to the bridge interface br-lan
  - eth1 is the interface at @wan

  - eth0 is assigned the MAC from 0x0 (*:A0)
  - eth1 is assigned the MAC from 0x1002 (*:A1)

  - br-lan inherits the MAC from eth0 (*:A0)
  - @wan inherits the MAC from eth1 (*:A1)

  - radio0's MAC is overwritten to the one at 0x6

This way, eth0/eth1's positions differ from the stock firmware, but
the weird MAC ressignations in br-lan/br-wan are avoided while the
external behaviour of the router is maintained. Additionally, WAN
port is connected to the PHY gmac, allowing to monitor the link
status (e.g., to restart DHCP negotiation when plugging a cable).

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2019-10-13 20:34:57 +08:00
Adrian Schmutzler 0aab49d234 treewide: fix hex2dec conversion for MAC address checksum offset
If chksum_offset is converted by $(($...)) at the beginning, the
check [ -n "$chksum_offset" ] will always return true, as the
conversion yields "0" for an empty argument, and [ -n "0" ] is
true.

With this patch, the variable is not converted before the check,
but only when it's used in dd.

No conversion is done for use in hexdump, as this can deal with
hex value offsets.

Fixes: b133e466b0 ("treewide: convert WiFi caldata size and offset to hexadecimal")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-09-29 00:46:13 +02:00
Dmitry Tunin 00ed75f47f ath79: add support of Netgear WNDR3800CH
Add support for the ar71xx supported Netgear WNDR3800CH to ath79.
The device is identical to WNDR3800 except NETGEAR_BOARD_ID.

Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-09-21 23:41:31 +02:00
Adrian Schmutzler f8d8b3f85d ath79: remove invalid uses of ath9k_patch_fw_mac_crc
Some ar9344-based devices are using ath9k_patch_fw_mac_crc, which
is meant to generate a checksum, for fixing their ath9k MAC
addresses.
However, those do not have a checksum field, and the calculated
checksum offset would be negative.

This patch will use ath9k_patch_fw_mac function for those devices.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-09-21 23:41:31 +02:00
Keith Maika 4cb5f29625 ath79: add support for TP-Link Archer C59v2
Add ath79 support for Archer C59v2, previously supported by ar71xx.

TP-Link Archer C59v2 is a dual-band AC1350 router based on
Qualcomm/Atheros QCA9561+QCA9886 chips.

Specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- USB 2.0 port
- UART header on PCB

Flash instruction:
  - via web UI:
    1. Download openwrt-ath79-generic-tplink_archer-c59-v2-squashfs-factory.bin
    2. Login to router and open the Advanced tab
    3. Navigate to System Tools -> Firmware Upgrade
    4. Upload firmware using the Manual Upgrade form
  - via TFTP:
    1. Set PC to fixed ip address 192.168.0.66
    2. Download openwrt-ath79-generic-tplink_archer-c59-v2-squashfs-factory.bin
       and rename it to tp_recovery.bin
    3. Start a tftp server with the file tp_recovery.bin in its root directory
    4. Turn off the router
    5. Press and hold Reset button
    6. Turn on router with the reset button pressed and wait ~15 seconds
    7. Release the reset button and after a short time
       the firmware should be transferred from the tftp server
    8. Wait ~30 second to complete recovery.

Signed-off-by: Keith Maika <keithm@aoeex.com>
2019-09-16 21:40:06 +02:00
Adrian Schmutzler fbbb4eb8b4 ath79: add support for TP-Link WDR3500 v1
Hardware:
SoC:      AR9344
CPU:      560 MHz
Flash:    8 MiB
RAM:      128 MiB
WiFi:     Atheros AR9340 2.4GHz 802.11bgn
          Atheros AR9300 5GHz 802.11an
Ethernet: AR934X built-in switch, WAN on separate physical interface
USB:      1x 2.0

Flash instruction (WebUI):
Download *-factory.bin image and upload it via the firmwary upgrade
function of the stock firmware WebUI.

Flash instruction (TFTP):
1. Set PC to fixed ip address 192.168.0.66
2. Download *-factory.bin image and rename it to
   wdr3500v1_tp_recovery.bin
3. Start a tftp server with the image file in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[removed stray newline]
Signed-off-by: David Bauer <mail@david-bauer.net>
2019-09-03 18:43:27 +02:00
Luochongjun 921675a2d1 ath79: add support for gl-ar750
This patch supports gl-ar750, which was previously supported by ar71xx.

Specification:
- SOC: QCA9531 (650MHz)
- Flash: 16 MiB (W25Q128FVSG)
- RAM: 128 MiB DDR2
- Ethernet: 10/100: 2xLAN + 10/100: 1xWAN
- Wireless: 2.4GHz (bgn) and 5GHz (ac)
- USB: 1x USB 2.0 port
- Switch: 1x switch
- Button: 1x reset button
- LED: 3x LEDS (white)

Flash instruction:
Support for sysupgrade directive upgrades, as well as luci upgrades.

Signed-off-by: Luochongjun <luochongjun@gl-inet.com>
2019-08-24 08:55:33 +08:00
Adrian Schmutzler b133e466b0
treewide: convert WiFi caldata size and offset to hexadecimal
This changes size and offset set for WiFi caldata extraction and
MAC address adjustment to hexadecimal notation.

This will be much clearer for the reader when numbers are big, and
will also match the style used for mtd-cal-data in DTS files.

Since dd cannot deal with hexadecimal notation, one has to convert
back to decimal by simple $(($hexnum)).

Acked-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-08-14 12:36:37 +02:00
Adrian Schmutzler 75bfc393ba treewide: convert MAC address location offsets to hexadecimal
This changes the offsets for the MAC address location in
mtd_get_mac_binary* and mtd_get_mac_text to hexadecimal notation.

This will be much clearer for the reader when numbers are big, and
will also match the style used for mtd-mac-address in DTS files.

(e.g. 0x1006 and 0x5006 are much more useful than 4102 and 20486)

Acked-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-08-14 12:10:12 +02:00
Adrian Schmutzler 2758dd332c ath79: fix whitespace errors from adding D-Link DIR-842 C3
We completely overlooked whitespace errors when reviewing
796ad2f7ef ("ath79: add support for D-Link DIR-842 C3").

Fix them and and also fix Makefile indent for C1/C2.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-08-09 17:08:46 +02:00
Joan Moreau 9ed272fe95 ath79: add support for Comfast WR650AC v1/v2
This is a dual band 11a/11n router with 1x wan and 4x gig lan ports.

There are two versions of this router which can be identified through
the factory web interface, v1 has 128mb ram and a uboot size of 128k,
v2 has 256mb ram and a uboot size of 256k, the remaining hardware and
PCB markings are the same.

Short specification:

    SoC: Qualcomm Atheros QCA9558 - 720 MHz
    Switch: Atheros AR8327
    Second radio : Qualcomm Atheros QCA9880 802.11ac
    4 LAN/1 WAN 1000Mps Ethernet
    256 MB of RAM (DDR2)
    16 MB of FLASH
    3x2.4 GHz, 3x5GHz antennas

Steps to install :

Option A : Use vendor UI

Option B (if A is not working) :
(a) Download 'backup' from vendor UI and rename it backup.tar.gz
(b) Open the archive, and update the root password in /etc/shadow by
    '$1$9wX3HGfB$X5Sb3kqzzBLdKRUR2kfFd0'
(c) 'Restore' from the archive using the vendor UI. Root password is now
    'aaa'
(d) Scp the firwmware to the device:
    $ scp <openwrt-sysupgrade>.bin root@192.168.1.1:/
(d) ssh to the device and flash the firmware:
    $ cd /
    $ mtd -e firmware -r write <openwrt-sysupgrade>.bin firmware

Signed-off-by: Gareth Parker <gareth41@orcon.net.nz>
Signed-off-by: Ding Tengfei <dtf@comfast.cn>
Signed-off-by: Joan Moreau <jom@grosjo.net>
[reformatted commit message]
Signed-off-by: David Bauer <mail@david-bauer.net>
2019-08-09 17:07:07 +02:00
Perry Melange 796ad2f7ef ath79: add support for D-Link DIR-842 C3
Hardware spec of DIR-842 C3:
SoC: QCA9563
DRAM: 128MB DDR2
Flash: 16MB SPI-NOR
Switch: QCA8337N
WiFi 5.8GHz: QCA9888
WiFi 2.4Ghz: QCA9563
USB: circuit onboard, but components are not soldered

Flash instructions:

1. Upgrade the factory.bin through the factory web interface or
   the u-boot failsafe interface.
   The firmware will boot up correctly for the first time.
   Do not power off the device after OpenWrt has booted.
   Otherwise the u-boot will enter failsafe mode as the checksum
   of the firmware has been changed.
2. Upgrade the sysupgrade.bin in OpenWrt.
   After upgrading completes the u-boot won't complain about the
   firmware checksum and it's OK to use now.
3. If you powered off the device before upgrading the sysupgrade.bin,
   just upgrade the factory.bin through the u-boot failsafe interface
   and then goto step 2.

Signed-off-by: Perry Melange <isprotejesvalkata@gmail.com>
2019-08-07 21:17:40 +02:00
Jackson Lim 030fc6ab6c ath79: add support for D-Link DIR-842 C1
Hardware spec of DIR-842 C1:
SoC: QCA9563
DRAM: 128MB DDR2
Flash: 16MB SPI-NOR
Switch: QCA8337N
WiFi 5.8GHz: QCA9888
WiFi 2.4Ghz: QCA9563
USB: circuit onboard, but components are not soldered

Flash instructions:

1. Upgrade the factory.bin through the factory web interface or
   the u-boot failsafe interface.
   The firmware will boot up correctly for the first time.
   Do not power off the device after OpenWrt has booted.
   Otherwise the u-boot will enter failsafe mode as the checksum
   of the firmware has been changed.
2. Upgrade the sysupgrade.bin in OpenWrt.
   After upgrading completes the u-boot won't complain about the
   firmware checksum and it's OK to use now.
3. If you powered off the device before upgrading the sysupgrade.bin,
   just upgrade the factory.bin through the u-boot failsafe interface
   and then goto step 2.

Signed-off-by: Jackson Lim <jackcolentern@gmail.com>
[fix whitespace issues]
Signed-off-by: David Bauer <mail@david-bauer.net>
2019-08-05 10:54:11 +02:00
Jackson Lim 209b368254 ath79: add support for D-Link DIR-842 C2
Hardware spec of DIR-842 C2:
SoC: QCA9563
DRAM: 128MB DDR2
Flash: 16MB SPI-NOR
Switch: QCA8337N
WiFi 5.8GHz: QCA9888
WiFi 2.4Ghz: QCA9563
USB: 2.0

Flash instructions:

1. Upgrade the factory.bin through the factory web interface or
   the u-boot failsafe interface.
   The firmware will boot up correctly for the first time.
   Do not power off the device after OpenWrt has booted.
   Otherwise the u-boot will enter failsafe mode as the checksum
   of the firmware has been changed.
2. Upgrade the sysupgrade.bin in OpenWrt.
   After upgrading completes the u-boot won't complain about the
   firmware checksum and it's OK to use now.
3. If you powered off the device before upgrading the sysupgrade.bin,
   just upgrade the factory.bin through the u-boot failsafe interface
   and then goto step 2.

Signed-off-by: Jackson Lim <jackcolentern@gmail.com>
[Reword reset-hog comment, fix formatting]
Signed-off-by: David Bauer <mail@david-bauer.net>
2019-07-24 11:36:02 +02:00
Adrian Schmutzler 974d6958a7 ath79: Add support for TP-Link Archer C60 v2
TP-Link Archer C60 v2 is a dual-band AC1350 router,
based on Qualcomm/Atheros QCA9561 + QCA9886.

Specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 7x LED, 2x button
- UART header on PCB

Flash instruction (WebUI):
Download *-factory.bin image and upload it via the firmwary upgrade
function of the stock firmware WebUI.

Flash instruction (TFTP):
1. Set PC to fixed IP address 192.168.0.66
2. Download *-factory.bin image and rename it to tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root
   directory
4. Turn off the router
5. Press and hold reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time the firmware should
   be transferred from the tftp server
8. Wait ~30 second to complete recovery

Flash instruction (under U-Boot, using UART):
tftp 0x81000000 ...-sysupgrade.bin
erase 0x9f030000 +$filesize
cp.b $fileaddr 0x9f030000 $filesize
reset

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-18 00:06:55 +02:00
Adrian Schmutzler 6d313da6dc ath79: Add support for TP-Link Archer C60 v1
TP-Link Archer C60v1 is a dual-band AC1350 router,
based on Qualcomm/Atheros QCA9561+QCA9886.

Specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 7x LED, 2x button
- UART header on PCB

Flash instruction (WebUI):
Download *-factory.bin image and upload it via the firmwary upgrade
function of the stock firmware WebUI.

Flash instruction (TFTP):
1. Set PC to fixed ip address 192.168.0.66
2. Download *-factory.bin image and rename it to tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.

Flash instruction under U-Boot, using UART:
1. tftp 0x81000000 ...-sysupgrade.bin
2. erase 0x9f020000 +$filesize
3. cp.b $fileaddr 0x9f020000 $filesize
4. reset

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-18 00:06:55 +02:00
Pramod Pancha 8e384ba830 ath79: add support for Trendnet TEW-823DRU
Trendnet TEW-823DRU is a dual-band AC1750 router.
The router is based on Qualcomm/Atheros QCA9558 + QCA9880.

Specification:

720 MHz CPU
256 MB of RAM
16 MB of FLASH
3T3R 2.4 GHz
3T3R 5 GHz
5x 10/100/1000 Mbps Ethernet

Firmware can be flashed from the web interface. Tested on 3 routers
with no issues.

Signed-off-by: Pramod Pancha <pancha@vill.com>
[whitespace fixes]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-07-18 00:06:55 +02:00
Christoph Krapp 6fde0b735c ath79: add support for TP-Link RE355 v1 and RE450 v1
Specification:

SoC: Qualcomm Atheros QCA9558
RAM: 64/128MiB
Flash: 8MiB SPI-NOR
Wifi:
  - 2.4GHz: 3T3R (QCA9558)
  - 5GHz: 3T3R (QCA9880)
LAN: 1x 10/100/1000 Mbps
UART:
  - TP1: Tx
  - TP2: Rx
  - TP3: Gnd
  - TP4: 3v3

Flash instructions:
Flash factory image through stock firmware WEB UI.

Signed-off-by: Christoph Krapp <achterin@googlemail.com>
2019-07-17 23:14:23 +02:00
Daniel Gimpelevich bc18c2bfe7 ath79: add support for Bluesocket BSAP1880 board
This board was used in dual-band 802.11n enterprise access points, models
BSAP-1800v2 and BSAP-1840, introduced in 2010 by Bluesocket, which was
acquired by Adtran in 2011, who has now EOL'ed them. They differed only in
that the BSAP-1840's antennae were detachable, while the BSAP-1800v2's were
inside the case. They have an external RJ-45 console port, which works with
standard Cisco 72-3383-01 console cables.

Specification:
- System-On-Chip: AR7161
- CPU/Speed: 600 MHz
- Flash-Chip: Macronix MX25L12845E
- Flash size: 16 MiB
- RAM: 64 MiB
- Wireless No1: Lite-On WN2601A card: AR9160/AR9103 2.4GHz 802.11bgn
- Wireless No2: Lite-On WN2502A card: AR9160/AR9106 5GHz 802.11an
- PHY: Vitesse VSC8601, Rev. B

Installation:
1. Connect to the serial console using a terminal that supports YMODEM at
   115200 bps, 8 data bits, no parity, 1 stop bit
2. Interrupt the bootloader using its password, which is: r00t
3. Issue the "fis init" command, confirming if prompted
4. Look at the length of the openwrt-ath79-generic-*-squashfs-kernel.bin
   file, and substitute it below, instead of where I have "LeNgTh"
5. Issue the following command, and upload this file using YMODEM protocol
   load -r -v -b 0x80060000 -m ymodem
6. Issue the following commands, substituting as mentioned above:
   fis create -b 0x80060000 -l LeNgTh vmlinux_2
   load -r -v -b 0x80100000 -m ymodem
7. Using YMODEM, upload openwrt-ath79-generic-*-squashfs-rootfs.bin
8. Issue the "fis free" command, and for the first range in its response,
   use a hexadecimal calculator to subtract the start from the end in order
   to substitute it below, with the leading "0x" to specify it in
   hexadecimal, instead of where I have "LeNgTh"
9. Issue the following commands, substituting as mentioned above:
   fis create -b 0x80100000 -l LeNgTh -e 0 -r 0 rootfs
   reset
10.Wait for the status LED to go solid green

Tested-by: Brian Gonyer <bgonyer@gmail.com>
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
[fixed obsolete $ARGV in platform_do_upgrade]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-07-17 22:59:29 +02:00
Chuanhong Guo d08b5bb344 ath79: add wmac migration for all ar93xx/qca95xx SoCs
Add migration for all ar71xx device path as well as previously
incorrect ath79 path.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-07-16 09:55:29 +08:00
Chuanhong Guo a9360452f0 ath79: add support for Qihoo C301
Specifications:
- SoC: AR9344
- RAM: 128MB
- Flash: 2 * 16MB (MX25L12845)
- Ethernet: 2 * FE LAN & 1 * FE WAN
- WiFi: 2.4G: AR9344 5G: QCA9882

Flash instruction:
1. Hold reset and power up the router
2. Set your IP to 192.168.1.x
3. Open 192.168.1.1 and upload the generated *factory* firmware

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2019-07-16 09:51:03 +08:00
David Bauer cb3cd52694 ath79: add support for devolo WiFi pro 1750x
Hardware
--------
CPU:   Qualcomm Atheros QCA9558
RAM:   128M DDR2
FLASH: 16MiB
ETH:   1x Atheros AR8035 (PoE in)
WiFi2: QCA9558 3T3R
WiFi5: QCA9880 3T3R
BTN:   1x Reset
LED:   1x LED Power (non-controllable)
       1x LED Status (internal)
       1x LED LAN (controlled by PHY)
       1x LED WLAN
BEEP:  1x GPIO attached piezo beeper
UART:  3.3V GND TX RX (115200-N-8) (3.3V is square pad)
       Header is located next to external-LED header.

Installation
------------
Make sure you set a password for the root user as prompted on first
setup!

1. Upload OpenWRT sysupgrade image via SSH to the device.
Use /tmp as the destination folder on the device.
User is root, password the one set in the web interface.

2. Install OpenWRT with

> sysupgrade -n -F /tmp/<openwrt-image-name>

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-07-14 16:20:53 +02:00
Adrian Schmutzler 1174b94bc9 ath79: Fix whitespace errors in 11-ath10k-caldata
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-09 23:05:51 +02:00
Adrian Schmutzler ab02584685 ath79: Use -v1 suffix for TP-Link WDR3600/4300
In ath79, identifiers tplink_tl-wdr3600 and tplink_tl-wdr4300 have
been used while most other TP-Link devices include the revision.

Although there actually is only one major revision of these
devices, they bear the revision on their bottom (v1.x). TP-Link
also refers to the devices as V1 on its web page.

This patch thus adds -v1 to both so it is more consistent
with other devices and with what you would expect from reading
the on-device sticker and the support pages.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-07-03 07:45:00 +02:00
Adrian Schmutzler b16faf9bc7 ath79: Code style improvements in 10_fix_wifi_mac
This fixes one comparison and several useless echos.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-06-25 00:52:35 +02:00
Adrian Schmutzler 28baaaae82 ath79: Merge cases in 11-ath10k-caldata
Cosmetical patch that just merges two cases.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-06-15 19:55:32 +02:00
Adrian Schmutzler fde0abf267 ath79: Add support for TP-Link Archer C25 v1
The TP-Link Archer C25 is a low-cost dual-band router.

Specification:

- CPU: Atheros QCA9561 775 MHz
- RAM: 64 MB
- Flash: 8 MB
- Wifi: 3x3 2.4 GHz (integrated), 1x1 5 GHz QCA9887
- NET: 5x 10/100 Mbps Ethernet

Some LEDs are controlled by an additional 74HC595 chip, but not
all of them as e.g. for the C59.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-06-10 11:25:47 +02:00
David Santamaría Rogado e19506f206 ath79: migrate Archer C7 5GHz radio device paths
When upgrading a TP-Link Archer C7 v2 from ar71xx to ath79,
the 5ghz radio stops working because the device path changed.

Some people subtitute the unsupported QCA9880v1 in the Archer v1
with supported QCA9880v2 radio. Since the stock radio doesn't
work, so it's safe to apply the change also for the Archer v1
images as well.

Also this patch renames the migration file and variables from
wmac to wifi.

Signed-off-by: David Santamaría Rogado <howl.nsp@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[removed comment, added return 0 (not that it matters since uci is
clever, see 00-wmac-migration thread), reworded commit message]
2019-06-10 11:25:46 +02:00
Adrian Schmutzler fcb920ffe7 ath79: Consistently label art partition with lower case
This patch harmonizes the label and alias for art partitions
across ath79. Since lower case seems to be more frequent, use that
consistently.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-06-10 11:25:41 +02:00
Adrian Schmutzler 4d807ad2d9 ath79: Read MAC addresses from flash in 11-ath10k-caldata
In commit c3a8518 eth0 and eth1 have been swapped for some devices,
but 11-ath10k-caldata has not been updated.
Instead of fixing this by swapping eth0/eth1, this patch will read
addresses from flash (as done for several devices already) so
adjustments due to eth order become obsolete.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2019-06-10 11:25:41 +02:00
Ryan Mounce 6d6985ff0e ath79: add support for WD My Net N750
SoC: AR9344
RAM: 128MB
Flash: 16MiB Winbond 25Q128BVFG SPI NOR
5GHz WiFi: AR9380 PCIe 3x3:3 802.11n
2.4GHz WiFi: AR9344 (SoC) AHB 2x2:2 802.11n

5x Gigabit ethernet via AR8327N switch (green + amber LEDs)
2x USB 2.0 via GL850G hub
4x front LEDs from SoC GPIO
1x front WPS button from SoC GPIO
1x bottom reset button from SoC GPIO

Known issues:
AR8327N LEDs only have default functionality, not presented in sysfs.
This is a regression from ar71xx.

UART header JP1, 115200 no parity 1 stop
TX
GND
VCC
(N/P)
RX

See https://openwrt.org/toh/wd/n750 for flashing detail.
Procedures unchanged from ar71xx.

Tested sysupgrade + factory flash from WD Emergency Recovery

Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
2019-05-27 22:44:08 +02:00
Davide Fioravanti f5d2c91415 ath79: add support for TP-Link Archer D50 V1
TP-Link Archer D50 v1 is a dual-band AC1200 router + modem.
The router section is based on Qualcomm/Atheros QCA9531 + QCA9882.
The "DSL" section is based on BCM6318 but it's currently not supported.

Internally eth0 is connected to the Broadcom CPU.

Router section - Specification:

CPU: QCA9531 650/600/200 MHz (CPU/DDR/AHB)
RAM: 64 MB (DDR2)
Flash: 8 MB (SPI NOR)
Wifi 2.4GHz: QCA9531 2T2R
Wifi 5GHz: QCA9982 2T2R
4x 10/100 Mbps Ethernet
8x LED, 3x button
UART header on PCB

Known issues:
DSL not working (eth0) (WIP)

UART connection
---------------
J2 HEADER (Qualcomm CPU)
. TX
. RX
. GND
O VCC

J16 HEADER (Broadcom CPU)
O VCC
. GND
. RX
. TX

The following instructions require a connection to the J2 UART header.

Flash instruction under U-Boot, using UART
------------------------------------------
 1. Press any key to stop autobooting and obtain U-Boot CLI access.
 2. Setup ip addresses for U-Boot and your tftp server.
 3. Issue below commands:
	tftpboot 0x81000000 openwrt-ath79-generic-tplink_archer-d50-v1-squashfs-sysupgrade.bin
	erase 0x9f020000 +$filesize
	cp.b 0x81000000 0x9f020000 $filesize
	reset

Initramfs instruction under U-Boot for testing, using UART
----------------------------------------------------------
 1. Press any key to stop autobooting and obtain U-Boot CLI access.
 2. Setup ip addresses for U-Boot and your tftp server.
 3. Issue below commands:
	tftpboot 0x81000000 openwrt-ath79-generic-tplink_archer-d50-v1-initramfs-kernel.bin
	bootm 0x81000000

Restore the original firmware
-----------------------------
 0. Backup every partition using the OpenWrt web interface
 1. Download the OEM firmware from the TP-Link website
 2. Extract the bin file in a folder (eg. Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin)
 3. Remove the U-Boot and the Broadcom image part from the file.
    Issue the following command:
	dd if="Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin" of="Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin.mod" skip=257 bs=512 count=15616
 4. Double check the .mod file size. It must be 7995392 bytes.
 5. Flash it using the OpenWrt web interface. Force the update if needed.
    WARNING: Remember to NOT keep settings.

 5b. (Alternative to 5.) Flash it using the U-Boot and UART connection.
     Issue below commands in the U-Boot:
        tftpboot 0x81000000 Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin.mod
        erase 0x9f020000 +$filesize
        cp.b 0x81000000 0x9f020000 $filesize
        reset

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [removed
default-state = "off", it's already the default, added pcie node,
fixed typo]
2019-05-18 17:59:49 +02:00
sven friedmann 30dcbc741d ath79: add support for EnGenius ECB1750
Specification:

- Qualcomm Atheros SoC QCA9558
- 720/600/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 1x 10/100/1000 Mbps Ethernet
- 3T3R 2.4 GHz (QCA9558 WMAC)
- 3T3R 5.8 Ghz (QCA9880-BR4A, Senao PCE4553AH)

https://fccid.io/A8J-ECB1750

Tested and working:

- lan, wireless, leds, sysupgrade (tftp)

Flash instructions:

1.) tftp recovery

- use a 1GbE switch or direct attached 1GbE link
- setup client ip address 192.168.1.10 and start tftpd
- save "openwrt-ath79-generic-engenius_ecb1750-initramfs-kernel.bin" as "ap.bin" in tfpd root directory
- plugin powercord and hold reset button 10secs.. "ap.bin" will be downloaded and executed
- afterwards login via ssh and do a sysuprade

2.) oem webinterface factory install (not tested)

Use normal webinterface upgrade page und select "openwrt-ath79-generic-engenius_ecb1750-squashfs-factory.bin".

3.) oem webinterface command injection

OEM Firmware already running OpenWrt (Attitude Adjustment 12.09).
Use OEM webinterface and command injection. See wiki for details.

https://openwrt.org/toh/engenius/engenius_ecb1750_1

Signed-off-by: sven friedmann <sf.openwrt@okay.ms>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[use interrupt-driven "gpio-keys" binding]
2019-05-18 13:43:55 +02:00
Daniel Gimpelevich f61e754522 ath79: add support for Netgear EX6400 and EX7300
This is sold as a dual-band 802.11ac range extender. It has a sliding
switch for Extender mode or Access Point mode, a WPS button, a recessed
Reset button, a hard-power button, and a multitude of LED's, some
multiplexed via an NXP 74AHC164D chip. The internal serial header pinout is
Vcc, Tx, Rx, GND, with GND closest to the corner of the board. You may
connect at 115200 bps, 8 data bits, no parity, 1 stop bit.

Specification:
- System-On-Chip: QCA9558
- CPU/Speed: 720 MHz
- Flash-Chip: Winbond 25Q128FVSG
- Flash size: 16 MiB
- RAM: 128 MiB
- Wireless No1: QCA9558 on-chip 2.4GHz 802.11bgn, 3x3
- Wireless No2: QCA99x0 chip 5GHz 802.11an+ac, 4x4
- PHY: Atheros AR8035-A

Installation:
If you can get to the stock firmware's firmware upgrade option, just feed
it the factory.img and boot as usual. As an alternative, TFTP the
factory.img to the bootloader.

Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
[whitespace fix in DTS and reorder of make variables]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-04-09 11:09:26 +02:00
Markus Scheck de2f888024 ath79: add support for OCEDO Ursus
SOC:   Qualcomm Atheros QCA9558
RAM:   128MB
FLASH: 16MB (Macronix MX25L12845EMI-10G)
WLAN1: QCA9558 2.4GHz 802.11bgn 3SS
WLAN2: QCA9880 5GHz 802.11ac 3SS
LED:   Power, LAN1, LAN2, 2.4GHz, 5GHz
Serial:Next to SPI Flash,
       Pinout is 3V3 - GND - TX - RX (Square Pin is 3V3)
       The Serial setting is 115200-8-N-1

INSTALLATION:

1. Serve an OpenWrt ramdisk image named "ursus.bin".
   Set your IP-address to 192.168.100.8/24.
2. Connect to the serial. Power up the device and interrupt
   the boot process.
3. Set the correct bootcmd with
   > setenv bootcmd run bootcmd_1
   > saveenv
4. Run
   > tftpboot 0x81000000 ursus.bin
   > bootm 0x81000000
5. Wait for OpenWrt to boot up.
6. Transfer OpenWrt sysupdate image and flash via sysupgrade.

Signed-off-by: Markus Scheck <markus.scheck1@gmail.com>
Tested-by: David Bauer <mail@david-bauer.net>
[whitespace fix, renamed LED labels and SoC type fix]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-04-08 18:37:04 +02:00
INAGAKI Hiroshi 643fcfc8d6 ath79: add support for NEC Aterm WG1200CR
NEC Aterm WG1200CR is a 2.4/5 GHz band 11ac router,
based on Qualcomm Atheros QCA9563.

Specification:

- SoC		: Qualcomm Atheros QCA9563
- RAM		: DDR2 128 MiB
- Flash		: SPI-NOR 8 MiB
- WLAN		: 2.4/5 GHz 2T2R
  - 2.4 GHz	: QCA9563 (SoC)
  - 5 GHz	: QCA9888
- Ethernet	: 2x 10/100/1000 Mbps
  - Switch	: QCA8334
- LEDs/Input	: 12x/4x (2x buttons, 1x slide-switch)
- UART		: through-hole on PCB
  - JP1: Vcc, GND, NC, TX, RX from power connector side
  - 115200 bps

Flash instruction using factory image:

1. Boot WG1200CR normaly
2. Access to "http://192.168.10.1/" and open firmware update page
("ファームウェア更新")
3. Select the OpenWrt factory image and click update ("更新") button
to perform firmware update
4. Wait ~150 seconds to complete flashing

Known issues:

- cannot be controlled LEDs other than Power (Green/Red)
  - only Power LEDs are connected to SoC GPIO; other LEDs
    connected to the gpiochip on ath10k chip (QCA9888)

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [commit
message formatting]
2019-04-06 19:14:06 +02:00