mirror of https://github.com/hak5/openwrt.git
ath79: add support for Qihoo C301
Specifications: - SoC: AR9344 - RAM: 128MB - Flash: 2 * 16MB (MX25L12845) - Ethernet: 2 * FE LAN & 1 * FE WAN - WiFi: 2.4G: AR9344 5G: QCA9882 Flash instruction: 1. Hold reset and power up the router 2. Set your IP to 192.168.1.x 3. Open 192.168.1.1 and upload the generated *factory* firmware Signed-off-by: Chuanhong Guo <gch981213@gmail.com>master
Chuanhong Guo
parent
fae125781e
commit
a9360452f0
|
|
@ -29,6 +29,9 @@ openmesh,om5p-ac-v2|\
|
|||
yuncore,a770)
|
||||
ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x10000" "0x10000"
|
||||
;;
|
||||
qihoo,c301)
|
||||
ubootenv_add_uci_config "/dev/mtd9" "0x0" "0x10000" "0x10000"
|
||||
;;
|
||||
esac
|
||||
|
||||
config_load ubootenv
|
||||
|
|
|
|||
|
|
@ -104,6 +104,9 @@ pcs,cr3000)
|
|||
ucidef_set_led_switch "lan3" "LAN3" "pcs:blue:lan3" "switch0" "0x10"
|
||||
ucidef_set_led_switch "lan4" "LAN4" "pcs:blue:lan4" "switch0" "0x02"
|
||||
;;
|
||||
qihoo,c301)
|
||||
ucidef_set_led_wlan "wlan" "WLAN" "$boardname:green:wlan" "phy0tpt"
|
||||
;;
|
||||
tplink,archer-a7-v5|\
|
||||
tplink,archer-c7-v4|\
|
||||
tplink,archer-c7-v5)
|
||||
|
|
|
|||
|
|
@ -184,6 +184,11 @@ ath79_setup_interfaces()
|
|||
ucidef_add_switch "switch0" \
|
||||
"0@eth0" "3:lan:1" "5:lan:2" "4:wan"
|
||||
;;
|
||||
qihoo,c301)
|
||||
ucidef_set_interface_wan "eth1"
|
||||
ucidef_add_switch "switch0" \
|
||||
"0@eth0" "2:lan" "3:lan"
|
||||
;;
|
||||
rosinson,wr818)
|
||||
ucidef_add_switch "switch0" \
|
||||
"0@eth0" "1:lan" "2:lan" "3:wan"
|
||||
|
|
@ -328,6 +333,10 @@ ath79_setup_macs()
|
|||
lan_mac=$(k2t_get_mac "lan_mac")
|
||||
wan_mac=$(k2t_get_mac "wan_mac")
|
||||
;;
|
||||
qihoo,c301)
|
||||
lan_mac=$(mtd_get_mac_ascii devdata lanmac)
|
||||
wan_mac=$(mtd_get_mac_ascii devdata wanmac)
|
||||
;;
|
||||
rosinson,wr818)
|
||||
wan_mac=$(mtd_get_mac_binary factory 0)
|
||||
lan_mac=$(macaddr_setbit_la "$wan_mac")
|
||||
|
|
|
|||
|
|
@ -127,6 +127,10 @@ case "$FIRMWARE" in
|
|||
ath9k_eeprom_extract "art" 4096 1088
|
||||
ath9k_patch_fw_mac $(mtd_get_mac_text board_data 1664) 2
|
||||
;;
|
||||
qihoo,c301)
|
||||
ath9k_eeprom_extract "radiocfg" 4096 1088
|
||||
ath9k_patch_fw_mac $(mtd_get_mac_ascii devdata "wlan24mac") 2
|
||||
;;
|
||||
*)
|
||||
ath9k_eeprom_die "board $board is not supported yet"
|
||||
;;
|
||||
|
|
|
|||
|
|
@ -138,6 +138,10 @@ case "$FIRMWARE" in
|
|||
ath10kcal_extract "art" 20480 2116
|
||||
ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +16)
|
||||
;;
|
||||
qihoo,c301)
|
||||
ath10kcal_extract "radiocfg" 20480 2116
|
||||
ath10kcal_patch_mac_crc $(mtd_get_mac_ascii devdata wlan5mac)
|
||||
;;
|
||||
tplink,archer-a7-v5|\
|
||||
tplink,archer-c2-v3|\
|
||||
tplink,archer-c7-v4|\
|
||||
|
|
|
|||
|
|
@ -0,0 +1,11 @@
|
|||
#!/bin/sh /etc/rc.common
|
||||
START=99
|
||||
|
||||
boot() {
|
||||
case $(board_name) in
|
||||
qihoo,c301)
|
||||
local n=$(fw_printenv activeregion | cut -d = -f 2)
|
||||
fw_setenv "image${n}trynum" 0
|
||||
;;
|
||||
esac
|
||||
}
|
||||
|
|
@ -167,6 +167,7 @@ CONFIG_MTD_PARSER_CYBERTAN=y
|
|||
CONFIG_MTD_PHYSMAP=y
|
||||
CONFIG_MTD_SPI_NOR=y
|
||||
CONFIG_MTD_SPLIT_LZMA_FW=y
|
||||
CONFIG_MTD_SPLIT_SEAMA_FW=y
|
||||
CONFIG_MTD_SPLIT_TPLINK_FW=y
|
||||
CONFIG_MTD_SPLIT_UIMAGE_FW=y
|
||||
CONFIG_MTD_TPLINK_PARTS=y
|
||||
|
|
|
|||
|
|
@ -0,0 +1,236 @@
|
|||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
/dts-v1/;
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
#include "ar9344.dtsi"
|
||||
|
||||
/ {
|
||||
model = "Qihoo 360 C301";
|
||||
compatible = "qihoo,c301";
|
||||
|
||||
aliases {
|
||||
led-boot = &led_wlan_g;
|
||||
led-failsafe = &led_wlan_o;
|
||||
led-upgrade = &led_wlan_o;
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&jtag_disable_pins>;
|
||||
|
||||
led_wlan_g: wlan_g {
|
||||
label = "c301:green:wlan";
|
||||
gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led_wlan_o: wlan_o {
|
||||
label = "c301:orange:wlan";
|
||||
gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
|
||||
linux,default-trigger = "phy1tpt";
|
||||
};
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
reset {
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
};
|
||||
|
||||
reg_eth_led_vbus {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "eth_led_vbus";
|
||||
regulator-min-microvolt = <3300000>;
|
||||
regulator-max-microvolt = <3300000>;
|
||||
regulator-always-on;
|
||||
gpio = <&gpio 18 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
reg_usb_vbus {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "usb_vbus";
|
||||
regulator-min-microvolt = <5000000>;
|
||||
regulator-max-microvolt = <5000000>;
|
||||
enable-active-high;
|
||||
regulator-always-on;
|
||||
gpio = <&gpio 19 GPIO_ACTIVE_HIGH>;
|
||||
};
|
||||
};
|
||||
|
||||
&pinmux {
|
||||
pmx_spi_cs1: pinmux_spi_cs1 {
|
||||
pinctrl-single,bits = <0xc 0x07 0xff>;
|
||||
};
|
||||
|
||||
pmx_led_switch: pinmux_led_switch {
|
||||
pinctrl-single,bits = <0x0 0x2b2a2d00 0xffffff00>;
|
||||
};
|
||||
};
|
||||
|
||||
&ref {
|
||||
clock-frequency = <40000000>;
|
||||
};
|
||||
|
||||
&uart {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&gpio {
|
||||
status = "okay";
|
||||
|
||||
gpio_ext_lna0 {
|
||||
gpio-hog;
|
||||
gpios = <14 0>;
|
||||
output-high;
|
||||
line-name = "c301:ext:lna0";
|
||||
};
|
||||
|
||||
gpio_ext_lna1 {
|
||||
gpio-hog;
|
||||
gpios = <15 0>;
|
||||
output-high;
|
||||
line-name = "c301:ext:lna1";
|
||||
};
|
||||
};
|
||||
|
||||
&builtin_switch {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pmx_led_switch>;
|
||||
};
|
||||
|
||||
&spi {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pmx_spi_cs1>;
|
||||
status = "okay";
|
||||
|
||||
num-cs = <2>;
|
||||
cs-gpios= <0>, <0>;
|
||||
|
||||
flash@0 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-max-frequency = <25000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
uboot: partition@0 {
|
||||
label = "u-boot";
|
||||
reg = <0x0 0x40000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@40000 {
|
||||
label = "u-boot-env";
|
||||
reg = <0x40000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@50000 {
|
||||
label = "devdata";
|
||||
reg = <0x50000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@60000 {
|
||||
label = "devconf";
|
||||
reg = <0x60000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@70000 {
|
||||
compatible = "seama";
|
||||
label = "firmware";
|
||||
reg = <0x70000 0xf60000>;
|
||||
};
|
||||
|
||||
partition@fd0000 {
|
||||
label = "warm_start";
|
||||
reg = <0xfd0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@fe0000 {
|
||||
label = "action_image_config";
|
||||
reg = <0xfe0000 0x10000>;
|
||||
};
|
||||
|
||||
partition@ff0000 {
|
||||
label = "radiocfg";
|
||||
reg = <0xff0000 0x10000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
flash@1 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <1>;
|
||||
spi-max-frequency = <25000000>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "firmware2";
|
||||
reg = <0x0 0xf00000>;
|
||||
};
|
||||
|
||||
partition@f00000 {
|
||||
label = "privatedata";
|
||||
reg = <0xf00000 0x100000>;
|
||||
read-only;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&usb {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pcie {
|
||||
status = "okay";
|
||||
|
||||
wifi@0,0 {
|
||||
compatible = "qcom,ath10k";
|
||||
reg = <0 0 0 0 0>;
|
||||
};
|
||||
};
|
||||
|
||||
&wmac {
|
||||
status = "okay";
|
||||
qca,no-eeprom;
|
||||
};
|
||||
|
||||
ð1 {
|
||||
status = "okay";
|
||||
gmac-config {
|
||||
device = <&gmac>;
|
||||
switch-phy-swap = <1>;
|
||||
switch-only-mode = <1>;
|
||||
};
|
||||
};
|
||||
|
||||
ð0 {
|
||||
status = "okay";
|
||||
phy-handle = <&swphy0>;
|
||||
};
|
||||
|
|
@ -728,6 +728,18 @@ define Device/phicomm_k2t
|
|||
endef
|
||||
TARGET_DEVICES += phicomm_k2t
|
||||
|
||||
define Device/qihoo_c301
|
||||
$(Device/seama)
|
||||
ATH_SOC := ar9344
|
||||
DEVICE_VENDOR := Qihoo
|
||||
DEVICE_MODEL := C301
|
||||
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca988x-ct uboot-envtools
|
||||
IMAGE_SIZE := 15744k
|
||||
SEAMA_SIGNATURE := wrgac26_qihoo360_360rg
|
||||
SUPPORTED_DEVICES += qihoo-c301
|
||||
endef
|
||||
TARGET_DEVICES += qihoo_c301
|
||||
|
||||
define Device/rosinson_wr818
|
||||
ATH_SOC := qca9563
|
||||
DEVICE_VENDOR := Rosinson
|
||||
|
|
|
|||
Loading…
Reference in New Issue