This allows some basic region switching on Netgear R8000. More devices &
codes may be added. Ideally it should be converted into DT info & patch.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This makes use of cfg80211 feature backported & described in
188626f17c ("mac80211: backport cfg80211 support for
ieee80211-freq-limit DT property").
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Fixes build failure for kmod-can-c-can-platform which depends on
kmod-regmap for kernel 4.1 and 4.4.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This patch updates the QCA988X firmware to the latest revision
firmware-5.bin_10.2.4-1.0-00016
found in the official ath10k-firmware repository.
Tested on TP-Link Archer C7 v2.
Signed-off-by: Timo Sigurdsson <public_timo.s@silentcreek.de>
Host files installed in Build/InstallDev are target-specific and will stay
in $(STAGING_DIR)/host after the STAGING_DIR_HOSTPKG unification.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Packets which are merely forwarded by the router and which are neither
involved in any DNAT/SNAT nor originate locally, are considered INVALID
from a conntrack point of view, causing them to get dropped in the
zone_*_dest_ACCEPT chains, since those only allow stream with state NEW
or UNTRACKED.
Remove the ctstate restriction on dest accept chains to properly pass-
through unrelated 3rd party traffic.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Use ubus process signalling instead of 'kill pidof dnsmasq' for
SIGHUP signalling to dnsmasq when ntp says time is valid.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Most mac80211 drivers leave the SMPS field in the HT capabilities
uninitialized (unfortunately defaults to static SMPS), which leads to
some devices limiting themselves to single-stream rates in some modes
(mostly mesh and IBSS).
Signed-off-by: Felix Fietkau <nbd@nbd.name>
For 988X, 9980, 9984 CT firmware.
This should allow IBSS + RSN on at least the 988X firmware,
and includes recent stability fixes for all firmware.
Signed-off-by: Ben Greear <greearb@candelatech.com>
This at least makes it harder to hit some txq related
crashes on firmware restart, a potential memory leak,
and some other fixes.
Signed-off-by: Ben Greear <greearb@candelatech.com>
This causes problem when a FQDN is configured in /etc/config/system. The
domain name will appear twice in reverse DNS.
Next to that, there seems to be a bug in dnsmasq. From the manual page:
--interface-name=<name>,<interface>[/4|/6]
Return a DNS record associating the name with the primary address
on the given interface. This flag specifies an A or AAAA record for the
given name in the same way as an /etc/hosts line, except that the address
is not constant, but taken from the given interface. The interface may be
followed by "/4" or "/6" to specify that only IPv4 or IPv6 addresses
of the interface should be used. If the interface is down, not configured
or non-existent, an empty record is returned. The matching PTR record is
also created, mapping the interface address to the name. More than one name
may be associated with an interface address by repeating the flag; in that
case the first instance is used for the reverse address-to-name mapping.
It does not just create an A/AAAA record for the primary address, it creates
one for all addresses. And what is worse, it seems to actually resolve to the
non-primary address first. This is quite annoying when you use floating IP
addresses (e.g. VRRP), because when the floating IP is on the other device,
SSH failes due to incorrect entry in the known hosts file.
I know that this is not a common setup, but it would be nice if there was an
option to restore the previous behaviour, rather than just forcing this new
feature on everybody.
Reported-by: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Delete the map-t device when tearing down the map-t interface; as such
there's no conflict when the map-t interface comes up again when trying
to add the map-t device as the map-t device was still present
(Can not add: device 'map-wan6_4' already exists!).
Only call ifdown in teardown for map-e and lw6o4 map interfaces types
in order to suppress the trace "wan6_4 (6652): Interface wan6_4_ not found"
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
This reverts the following commits:
fbe522d120278ad007ee863888e44f96daf6352fcfd83555fc
This seems to trigger some mconf bugs when built with all feeds
packages, so I will try to find a less intrusive solution before the
release.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
wpa_supplicant allows only SAE as the key management
type for mesh mode. The recent key_mgmt rework unconditionally
added WPA-PSK - this breaks interface bringup and wpa_s
throws this error message:
Line 10: key_mgmt for mesh network should be open or SAE
Line 10: failed to parse network block.
Failed to read or parse configuration '/var/run/wpa_supplicant-wlan0.conf
Fix this by making sure that only SAE is used for mesh.
Signed-off-by: Sujith Manoharan <m.sujith@gmail.com>
The gettext-full host build might pick up iconv-stub host build headers
during the build, leading to stray linker errors with unresolved references
to libiconv_open(), libiconv() and libiconv_close().
Since we're not needing iconv support on the host, pass the appropriate
cache variables to configure to prevent detection and linking of iconv.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Cleanup to prepare for changing STAGING_DIR_HOSTPKG. The actual change of
STAGING_DIR_HOSTPKG (i.e., moving the host packages back into a common, not
target-specific directory) will be done after the first LEDE release, but
the cleanup will also be useful for projects like Gluon.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
This code was marked as incompatible to Linux 4.4 well over a year ago
and nobody cared, and now it's breaking builds.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Current board-2.bin file for qca9984 in Kvalo's repo is from branch
10.4-3.2, while board-2.bin file in code-aurora repo is newer and
corresponds to the branch 10.4-3.3, the same as recently updated firmware.
Considering that it's better to have all parts from the same branch
we are updating board-2.bin as well.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
It has never been used by default (due to being too bloated), and it is
properly replaced by usign (which has been the default for a long time
now).
Remove this feature to simplify the build system
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Rafał Miłecki
Stijn Tintel
Florian Fainelli
Timo Sigurdsson
Felix Fietkau
Matthias Schiffer
Koen Vandeputte
Hauke Mehrtens
Jo-Philipp Wich
Kevin Darbyshire-Bryant
Ben Greear
Hans Dedecker
Kabuli Chana
Sujith Manoharan
John Crispin
Pavel Kubelun