This patch adds support for the Accton WR6202 Mini 3G broadband router.
Full details for this device are available at
http://www.awbnetworks.com/products03.php?Fullkey=19.
This device is identical to the SMCWBR11S-3GN:
http://www.smc-asia.com/products03.php?Fullkey=210
It's also worth noting that this board has a GPIO line to control the
power to the USB port.
[juhosg:
- fix checkpatch warnings,
- reorder Kconfig entry,
- merge the sysupgrade patch,
- add GPL header]
Signed-off-by: Johnathan Boyce <jon.boyce@globalreach.eu.com>
SVN-Revision: 30434
This patch adds support for the Sitecom WL-341 v3 and other Sercomm
IP1006RRv2 based boards for sysupgrade support and for the initial
flash through pushbutton initiated recovery mode with the special
partition table and fixes for the quirks and things required by the
modified bootloader.
There is a known bug, Wi-Fi is not working on my board probably
because of the lack of RAM (the board only has 16MiB ram -- half of
the normal amount for non rebadged versions, but there is an empty
slot for another ram chip,) but I don't know for sure. The driver
loads but hostapd fails to load so I think it's not related to the
specific device except for the lack of RAM.
Moreover, only 7 of the 11 onboard leds are confirmed working, it
seems that one of the others is always on and the remaining ones are
connected to the wireless card leds already recognized by OpenWrt
[juhosg: reordered some parts in order to keep things sorted
alphabetically]
Signed-off-by: Marco Antonio Mauro <marcus90@gmail.com>
SVN-Revision: 29910
This add support for the Sitecom WL-351 v1 002.
In principle the Engenius ESR9850 should also work with this, but I
don't have the hardware to test it.
Since an external gigabit switch (RTL8366RB) is used,
I had to modify the ramips_esw driver to add a 'bypass' mode, which
just configures it to not filter the vlan tags.
Also two initialization words (FCT2 and FPA2) are set to different
values by u-boot than what the driver is using and it only seems to
work correctly when they not overridden by the driver, so I
added them to the platform specific data as reg_initval_fct2 and
reg_initval_fpa2.
With this wired lan works as expected, however I'm still having some
trouble with the wireless lan:
It only works after I rmmod & re-insmod rt2800pci and then
reconfigure it in the webinterface, but not directly after
rebooting.
The symptom of this is wpad saying:
Dec 20 15:45:09 OpenWrt daemon.info hostapd: wlan1: STA <notebookmac> IEEE 802.11: associated (aid 1)
Dec 20 15:45:09 OpenWrt daemon.info hostapd: wlan1: STA <notebookmac> WPA: pairwise key handshake completed (RSN)
Dec 20 15:45:22 OpenWrt daemon.info hostapd: wlan1: STA <notebookmac> IEEE 802.11: authenticated
But wpa_supplicant on the client saying:
Authentication with <wl351mac> timed out.
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
SVN-Revision: 29604
This patch adds support for the Omnima MiniEMBWiFi
Ralink RT3050F based board.
Based on a patch by Ivan Ignjatic <ivan at omnima.co.uk>
SVN-Revision: 29533
The preconfiguration of the USB LED has benn move to the
/etc/uci-defaults/leds script. [juhosg]
Signed-off-by: Adam Porter <porter.adam at gmail.com>
SVN-Revision: 28571
This patch adds initial board support for the MoFi Network MOFI3500-3GN
(Ralink RT3052F SoC, 8MB flash, 32MB ram, wireless N, USB-OTG). This
router is basically the NA version of the HW550-3G.
Signed-off-by: Layne Edwards <ledwards76@gmail.com>
SVN-Revision: 26466
This patch adds initial support for the Aztech HW550-3G (Ralink
RT3052f SoC, 8MB flash, 32MB dram). Ethernet is not working yet.
Wireless appears to work fine. USB does not work yet (as with other
Ralink boards).
Signed-off-by: Layne Edwards <ledwards76@gmail.com>
SVN-Revision: 26123
The attached patch adds a preliminary support for Prolink PWH2004 board
(Ralink RT305x based). LAN and flash appear to work. However, the USB
port and WLAN I have not managed to activate properly yet, but that
problem appears to be present with other rt305x targets as well(?).
Signed-off-by: Esa Hyytia <esa at netlab.tkk.fi>
SVN-Revision: 23129
This patch adds support for Sparklan WCR-150GN board.
Network configuration should be tweaked to make it work fully. The
reason it's not in this patch is that ramips target should be modified
to support different /etc/config/network files for different boards.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 22658
Gabor Juhos
John Crispin
Jo-Philipp Wich