In most cases it allows reverting back to the vendor firmware (as they
usually don't use UBI). If users wants to do that we can't do anything
anyway. Erease counters will be just lost. The only thing we do is warn:
"Flashing firmware without UBI for rootfs. All erase counters will be
lost."
It still requires forcing sysupgrade.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45392
We can now detect that provided firmware contains kernel and UBI image
partitions. Flashing it in a sane way (keeping erase counters) still
needs to be implemented.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45391
With previous version of patch info about need of erasing blocks was
stored once per boot. It was breaking in following scenario:
1) First boot after installation (erasing blocks after 0xdeadc0de)
2) Doing sysupgrade (with ubidetach & ubiformat)
3) Attaching UBI again (it caused all blocks to be erased)
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45387
It currently does not seem to make a difference anymore, except by
increasing compressed kernel image size
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 45385
* properly enclose macro arguments in paranthesis on use
* remove trailing white space
* convert C99 // comments
* add missing blank lines after declaration
* remove braces from single statement blocks
* split lines > 80 chars (except for one)
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45356
Having CONFIG_XZ_DEC_ARMTHUMB enabled breaks squashfs when ARM BCJ
filter was used to create the filesystem (and that's what we do on
all ARM targets). Thus unset CONFIG_XZ_DEC_ARMTHUMB to fix
squashfs on sunxi.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 45347
kmod-usb-phy-qcom-dwc3 is required to get USB working on ipq806x. It was
missed in previous commit so let's enable it automatically.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45345
MicroWRT is an wireless router with 2 USB,1 ethernet port. It
has a 16M flash and 64M DDR2 RAM. You can use most interface, such as
i2c, SPI, i2s and PCIe. Besides that there are three expansion borad to
combine with the core board. The detailed information, please refer to
https://www.microduino.cc/wiki/index.php?title=Main_Page
This patch adds support for it.
Because there is only one port,so disabled VLAN and use eth0 as lan
port. and only a power LED control by power pin.
Signed-off-by: 盛凯 <shengkai81@gmail.com>
SVN-Revision: 45331
None of the LEDs are enabled by default on the Hornet-UB X2 board
(the 16/64MB version of the Hornet-UB), because it uses a different
board-name ("hornet-ub-x2"); but hornet-ub and hornet-ub-x2 boards
are equivalent WRT their LEDs.
SIgned-off-by: Joshua Judson Rosen <jrosen@harvestai.com>
SVN-Revision: 45328
On newer Mikrotik boards, the radio calibration data
is stored differently and uses LZO compression instead
of RLE.
Update the RouterBOOT helper code to support the new
format.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 45297
First of all this patch was affecting other devices, not just Netgear
WNR834B. E.g. Linksys WRT300N v1 also has boardtype 0x0472.
This was breaking PCI on WRT300N, ssb couldn't detect core working in
hostmode (due to mips_busprobe32 failing).
Secondly this patch should not be needed for years now. From the analyze
of #8861 it seems it was needed just to make devices at slots other than
0 discoverable. Setting cardbus to 0 was simply making ssb allow access
to PCI config for devices other than bridge.
With the upstream commit a6c8462 (ssb: fix cardbus slot in hostmode) we
allow accessing device at slot 1 which should be enough for CardBus.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45293
SCHED_AUTOGROUP was turned on by default which forces the use of
CGROUPS, conflicting with the options we offer from menuconfig, remove
that.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 45275
Default profile already enables usb2 so we'll do the same for usb3 now
that we have support for it.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45262
This change adds DWC3 QCOM USB phys and TCSR drivers. These are
cherry-picked from the following LKML threads:
*dwc3 qcom: https://lkml.org/lkml/2014/9/12/599
*tcsr: https://lkml.org/lkml/2015/2/9/579
We're also adding an additional patch to add the corresponding dev nodes
in the IPQ806x and AP148 dts files.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45261
This change doesn't make USB functional but it does make it selectable
from a configuration perspective.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45259
These missing options have been noticed while enabling the following
configuration options on ipq806x, but they're available in the standard
kernel:
*ARCH_QCOM
*CONFIG_USB_SUPPORT
*CONFIG_USB_DWC3
*CONFIG_MFD_SYSCON
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45256
Options that used to be in target config have been added to the generic
config file, so remove them.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45255
original BeagleBoard has no Ethernet
provide a profile with all available USB Ethernet adapters
EBVBeagle comes with a kmod-usb-net-mcs7830 compatible device
tested with BeagleBoard C4
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 45237
- does not compile with 3.18
compile error: 'struct wl12xx_platform_data' has no member named 'gpio'
- different version was sent 2015 but cannot be tested by me
see "[PATCH v7 0/6] wlcore: add device-tree support" series
in linux-omap
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 45235
ZTE Q7 is a wireless router with SD Card,USB,1 ethernet port and a battery.It used MT7620a SoC.
I can,t find any information about this router on ZTE's website.
But I found this : http://en.cctairmobi.com/plus/list.php?tid=40
This router is the same as ZTE Q7 and later I found that both routers are made by the same company:-D
This patch adds support for it.
Because there is only one port,I disabled VLAN and use eth0 as lan port.
I could only create a sysupgrade firmware because I don't know how the orignal webpage check the uploaded image:-(
Signed-off-by: 郭传鈜 <gch981213@gmail.com>
SVN-Revision: 45208
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
v2: changes in input.mk broke the patch, some of the CONFIG_SND_*
stuff was added already
SVN-Revision: 45205
Platform device support has been removed from the gpio-74x164
driver in 3.14. Restore that.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 45203
Enabling this option renames the bootloader supplied root=
and rootfstype= variables, which might have to be know but
would break the automatisms OpenWrt uses.
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 45196
Use the latest version of the yaffs code. Fetched from the
yaffs2 git tree and it is based on the following commit:
commit 7e5cf0fa1b694f835cdc184a8395b229fa29f9ae
Author: Charles Manning <cdhmanning@gmail.com>
Date: Thu Aug 7 11:25:05 2014 +1200
yaffs-direct: Basic tests. Add lpthread flag for background gc support
Signed-off-by: Charles Manning <cdhmanning@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 45188
Accidentally left over development artifact.
Reported-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45179
KERNEL_IMAGE is used as target rule so reusing the same name causes:
Makefile:326: warning: overriding recipe for target `bin/brcm47xx/vmlinux.lzma'
Makefile:326: warning: ignoring old recipe for target `bin/brcm47xx/vmlinux.lzma'
Makefile:326: warning: overriding recipe for target `build_dir/target-mipsel_74kc+dsp2_uClibc-0.9.33.2/linux-brcm47xx_mips74k/vmlinux.lzma'
Makefile:326: warning: ignoring old recipe for target `build_dir/target-mipsel_74kc+dsp2_uClibc-0.9.33.2/linux-brcm47xx_mips74k/vmlinux.lzma'
Unfortunately this will cause copying vmlinux.lzma over and over like:
cp vmlinux.lzma FOO-kernel.bin
which is redundant on brcm47xx where we never modify kernel image.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45178
This makes sysupgrade reject firmware images for different devices.
Right now only support for 2 sample devices is implemented.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45170
Now that all supported boards have an dts there is no need for a
dtb free kernel anymore.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45169
Appearently the kernel only uses kernel above it, so moving it to an
higher address causes a lot of unavailable memory (#19327).
Also move the on-flash kernel to 0x80a0000, as newer CFEs don't like
uncompressing there (net-booting an ELF kernel is fine, though).
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45164
The setting has been lost during the transition to 3.18.
The CONFIG_M25PXX_PREFER_SMALL_SECTOR_ERASE option is not
available anymore, so use CONFIG_MTD_SPI_NOR_USE_4K_SECTORS
instead.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
SVN-Revision: 45161
There were a few issues with the existing code to detect the model string:
* Always using the string starting with byte 56 would cut off the W of WNDR when
the ID starts with 29763654+16+64 instead of 29763654+16+128
* The string contained garbage after the zero byte instead of cutting it off
after the zero (which wasn't always visible using busybox tools, but could
confuse other scripts)
Tested on a WNDR3700v1 and a WNDR3700v2 using the new 29763654+16+64 ID in the
ART. Furthermore, tested against ART dumps of a WNDR3700v2 using the old
$'\xff...' value and a WNDR3800.
The [ -z "$model" ] check was dropped as there is no way to actually hit this
unless no ART partition is found at all.
The awk command was carefully crafted to work both with gawk and the (horribly
broken) busybox awk.
Fixes#18992.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 45140
Update the xburst target to kernel version 3.18 and also remove the broken 3.10 support.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
SVN-Revision: 45031
ralink i2c driver is not working on MT7621 platform. Porting a new drivers from MTK's source code.
Last time i got some mess . This is new version.
Signed-off-by: Jay Weng <fl.service@t-firefly.com>
SVN-Revision: 45018
Should fix pcmcia on BCM6348 and BCM6358 after switching to DT-probed
gpio controllers.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44995
Fixes the following issue:
drivers/gpio/gpio-bcm63xx.c: In function 'bcm63xx_gpio_probe':
drivers/gpio/gpio-bcm63xx.c:80:4: error: implicit declaration of function 'devm_kasprintf' [-Werror=implicit-function-declaration]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44986
Support for the BT HomeHub 2.0 Type A.
This router was manufactured by Thomson, and it's BCM6358 based.
The leds are controled by two chained HC594, all working ok. The BCM5325
switch has the RESET# pin wired to the GPIO15, but currently there is no
way to tell the b53 driver how to get this gpio number in brcm63xx,
therefore swconfig won't use it when performing a switch reset.
The patch was tested with several firmwares, and all except unsupported
stuff (i.e xDSL) works pretty well.
Tested-by: Tahir <tahir00ali@gmail.com>
Signed-off-by: Daniel Gonzalez <dgcbueu@gmail.com>
SVN-Revision: 44985
Currently there isn't images ready for flashing liveboxes boards. This
patch adds a script and the code to call it in the bcm63xx images
builder makefile to generate the livebox 1 firmware.
I removed some lines to avoid generating unneded files in the bin/ dir
for this board. And added code to generate a squashed rootfs aligned to
64 kB since the current one in the /bin dir is 128 kB aligned and
doesn't work. Still no sysupgrade support for this board. Upgrading from
within openwrt can be done writing with mtd the kernel, and then the 64k
aligned rootfs.
Regards
Signed-off-by: Daniel Gonzalez <dgcbueu@gmail.com>
[jogo: use sed instead of a separate shell script for the boot script, make it
respect the load address]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44982
This backports upstream commit 702131e2a393b45174be326f1dbe20b658b4f157
bcma: move PCI IRQ control function to host specific code
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 44969
This changes the x86 image generation to match x86_64, using the PARTUUID for
the rootfs instead of explicitly configuring the device.
It unbreaks KVM with VirtIO, which uses /dev/vda2 instead of /dev/sda2.
Tested in QEMU/KVM with VirtIO, VirtualBox and VMware.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 44966
Otherwise the root device won't be found in 1/16 of the generated images
(whenever the signature starts with a zero digit).
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 44959
It depends on obsolete compilers and only works on one device (an
evaluation board).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 44956
also refresh generic patches for 3.14, 3.18, 3.19 and 4.0
targets might need a minor refresh as well, however, it looks
like everything still applies cleanly with occasional small
offsets.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 44876
There are two versions of the GL.iNet, the 6408A and the 6416A. The only
difference is the flash size.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 44860
Ensure gpio chips are always labeled the same; this allows simplifying
any arch setup gpio lookups.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44846
Now that we have converted all users of global variables to use
brcm63xx_board_name, we can savely convert the implicit call to detect
in brcm63xx.sh to a single, explicit call in preinit.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44840
r37000 made button kmods loaded from generic code, so we don't use
it anymore for deciding to load them.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44838
Instead of setting them up on invocation of brcm63xx_detect, set them
when calling diag.sh based.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44837
Board IDs are not unique, so in preparation for depricating them, always
use board_name for any (default) configuration decisions.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44836
Use the device tree model property for detecting the board instead
of board id from nvram if present.
Since we can now directly detect the DVA-G3810BN, we can remove the
extra check for it.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44834
Take full board name from devicetree, if present. Provide a method
for retrieving the board name.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44833
Rename board_name to board_id to prepare for using board_name as a
proper name for the board.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44832
This adds support for the Netgear DGND3700 v1 and DGND3800B.
DGND3700 v1 and DGND3800B are exactly the same router, only one difference,
the factory firmware. This patch produces two factory firmwares for each router.
The router includes an onboard NAND flash for extra storage. NAND is currently
not supported in bcm63xx, so no code added for this part. The NOR flash (32MB)
is enough for storing an openwrt firmware.
Signed-off-by: Daniel Gonzalez <dgcbueu@gmail.com>
[jogo: Add back commit message from v1]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44831
Build all geode platform drivers into the kernel
Remove kmod-* packages for these drivers
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 44809
While the switch positions aren't explicitly labeled as on and off, we've heard
complaints about them being wrong. This patch changes the handling to match the
stock firmware.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 44795
This patch allows AP148 to boot from NOR flash.
As we're using a FIT image as kernel (which includes kernel bin + DTB)
we enable the MTD_SPLIT_FIT_FW kernel option, which will detect the FIT
image and automatically split the "firmware" partition into 2 MTD parts
(kernel + rootfs).
The rootfs will then be parsed and split between rootfs + rootfs_data,
as usual.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 44794
Only one bootargs is really needed: the tty port. All the other
information will use the OpenWrt mechanisms.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 44793
If this option is enabled, the FIT image format will be detected and
split by the mtdsplit code. Detection is based upon the FDT magic, which
will trigger the parsing and detection of the rootfs, ending-up in the
creation of the 2 new partitions.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 44792
My previous patch regarding the Hornet-UB board
(commit: beed4d82d6a0154b0cd5f7b84e2180215ace6718) actually
causes the WPS led state to be inverted. Practically this meant
that value 0 in /sys/class/led/alfa:blue:wps/brightness would
turn the LED on and any positive value (1-255) would turn it off.
The above of course is confusing and hence reverting this value
back to the way it was before beed4d82d6a0154b0cd5f7b84e2180215ace6718.
Signed-off-by: Janne Cederberg <janne.cederberg@gmail.com>
SVN-Revision: 44791
It will now actually enable the mib counters instead of enabling rx/tx for
the first switch port.
Reported-by: Daniel Gonzalez <dgcbueu@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 44788
copied target/linux/x86/config-3.14 and target/linux/x86/patches-3.14 to
3.18 equivalents and then tweaked until it built.
Tested on alix2, soekris net4826 and soekris net4521.
Still having trouble with net4826 booting from Grub, alix2 and net4521
are fine.
Signed-off-by: Russell Senior <russell@personaltelco.net>
SVN-Revision: 44758
Move first 3 patches to 0xx numbers range to denote that this is
backported code and they should be removed when we update
kernel to version >= 3.19
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44732
To finally sync code with upsream cleanup registers headers, and update
several comments and kernel config symbols descriptions. No functional
changes.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44731
Cleanup board patch by moving code to specific patches, and factor out
leds to separate patch. No functional changes.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44729
Move GPIO patches behind PCI patch, since they are not yet merged
upstream.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44728
Make register names more consistent, mostly add appropriate prefix
(AR5312_ or AR2315_) or _BASE suffix. Also add macro to simplify mask
and shift operation.
No functional changes.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44726
There are no external users (last one was PCI driver) for these headers,
so move them to arch directory. Few macroses from ar231x.h header moved
to devices.h and file was removed.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44724
Honestly remap main SoC MMR mem and use accessor functions to
interact with registers. Now registers defined relatively to base
address (e.g. SDRAM controller base address).
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44723
AFAIK, no one AR2315+ chip (AR2315, AR2316, AR2317, AR2318) does not
contain IR block, so remove IR registers definitions. Also remove few
unused macroses.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44722
Pass PCI IRQ and I/O memory ranges via platform device resources, this
change makes PCI controller driver independed from arch headers, so
also remove few includes.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44721
Honestly remap PCI controller MMR and use accessor functions to interact
with registers.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44720
Add container and place all context specific variables and structure to
it.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44719
Put AR2315_PCI_HOST_SDRAM_BASEADDR macro to DMA header, since this is
arbitrary value and not some hw specific constant. Also this relocation
decouples dma from HW specific header.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44716
Do not use prom_init() callback, do memory initialization in
plat_mem_setup() callback and move serial port configuration to
arch_initcall stage.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44715
Check SoC family (AR5312+ or AR2315+) before call instead of checking it
inside the called function. Also convert ar{5312,2315}_init_device()
function to void, since they both return zero and nobody care about
return value.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44713
Sync functions, variables and enums names with upstream. Mostly replace
'ar231x_' prefix by 'ath25_'.
No functional changes, except few 'int' -> 'unsigned' changes.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44712
Ethernet controller driver don't use boarddata directly, so remove
corresponding field from its platform device structure.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
SVN-Revision: 44710
This problem has existed at least since Attitude Adjustment and
is also present in trunk. Basically on the Hornet-UB board the
functionality of RESET and WPS have "switched places".
There are two tickets about the issue at dev.openwrt.org,
The solution suggested on them both is incomplete though
and introduces the following proglem:
Patching as suggested on #14136/#15282 will result in a situation
where simply pressing the RESET button on the bottom will cause
FACTORY RESET to be run. This is due to GPIO high/low state being
incorrect as a result of the above change and virtually the RESET
button is in the pressed-down state the entire time. When it is
then physically pressed, that causes the opposite, release, to be
triggered and since to the board it seemed that the button was
pressed long before it was released, the FACTORY RESET results.
The attached patch works as expected. I have verified both the
incorrect functionality as well as after fixing the issue as
described in the patch and flashing the resulting firmware to a
Hornet-UB board.
Signed-off-by: Janne Cederberg <janne.cederberg@gmail.com>
SVN-Revision: 44692
ralink i2c driver is not working on MT7621 platform. Porting a new drivers from MTK's source code.
Signed-off-by: daixj <fl.service@t-firefly.com>
SVN-Revision: 44690
Here the device tree entry for ifxhcd is listed as compatible with one
supported in dwc2 (after patching the dwc driver appropriately).
A second entry is added to support the second core of the hcd. This
entry is listed to be compatible with only dwc2. Done this way there
should be backwards support for both hcd drivers (ltq-hcd and dwc2)
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
SVN-Revision: 44676
This patch switches calls to readl/writel to their
dwc2_readl/dwc2_writel equivalents which preserve platform endianness.
This patch is necessary to access dwc2 registers correctly on big
endian systems such as the mips based SoCs made by Lantiq. Then dwc2
can be used to replace ifx-hcd driver for Lantiq platforms found e.g.
in OpenWrt.
The patch was autogenerated with the following commands:
$EDITOR core.h
sed -i "s/\<readl\>/dwc2_readl/g" *.c hcd.h hw.h
sed -i "s/\<writel\>/dwc2_writel/g" *.c hcd.h hw.h
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
SVN-Revision: 44675
Lantiq driver does not work with autodetected fifo sizes so use ones
from original ltq-hcd driver in dwc2. Other values can be
autodetected.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
SVN-Revision: 44674
Port gpio code from original ltq-hcd driver to dwc2.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
SVN-Revision: 44673
Add VR9 specific usb initialization bits from ltq-hcd to platform
initialization.
This patch is more of a proof-of-concept than production quality
since the initialization registers are different on other lantiq
platforms.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
SVN-Revision: 44672
Previously, the generated images for the My Net Wi-fi Range Extender
wouldn't always work (and panic) due to the fixed mtd offsets and
sizes for the kernel and rootfs. This patch fixes the problem by
utilizing the shared Cybertan's partition parser to recalculate
the mtd partitions for every image dynamically everytime.
Reported-by: Pascal Paradis <peparadis@yahoo.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
SVN-Revision: 44665
By removing the NL16 signature check, the parser can be
utilized by other devices like the WD My Net Wi-fi Range
Extender.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
SVN-Revision: 44664
Felix Fietkau
Imre Kaloz
Rafał Miłecki
Luka Perkov
Zoltan Herpai
John Crispin
Jonas Gorski
Gabor Juhos
Florian Fainelli
Steven Barth
Lars-Peter Clausen
Jo-Philipp Wich
Nicolas Thill
Michael Büsch