This is a backport from the dnsmasq master which should fix a bug which
could cause a crash in dnsmasq.
I saw the following crashes in my log:
[522413.117215] do_page_fault(): sending SIGSEGV to dnsmasq for invalid read access from 2a001450
[522413.124464] epc = 004197f1 in dnsmasq[400000+23000]
[522413.129459] ra = 004197ef in dnsmasq[400000+23000]
This is happening in blockdata_write() when block->next is
dereferenced, but I am not sure if this is related to this problem or if
this is a different problem. I am unable to reproduce this problem.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
ipTIME A8004T is a 2.4/5GHz band AC2600 router, based on Mediatek
MT7621A.
Specifications:
- SoC: MT7621A
- RAM: DDR3 256M
- Flash: SPI NOR 16MB
- WiFi:
- 2.4GHz: MT7615E
- 5GHz: MT7615E
- Ethernet: 5x 10/100/1000Mbps
- Switch: SoC internal
- USB: 1 * USB3.0 port
- UART:
- J4: 3.3V, TX, RX, GND (3.3V is the square pad) / 57600 8N1
- Other info:
- J9: Unknown unpopulated header.
Installation via web interface:
1. Flash **initramfs** image through the stock web interface.
2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.
Revert to stock firmware:
1. Perform sysupgrade with stock image.
Signed-off-by: Yong-hyu Ban <perillamint@quendi.moe>
[do not enable xhci node in DTS which is already enabled in DTSI]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The MAC address on the label of this device corresponds to the
2.4 GHz and ethernet MAC address.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Add call to fclose for file pointer fp in function t_openpw.
The resource leak could happen during an error handling.
Signed-off-by: Andrea Dalla Costa <andrea@dallacosta.me>
Currently this device fails to boot with the OpenWrt snapshot images
(release images are unaffected). The error message is:
"LZMA ERROR 1 - must RESET board to recover".
This happens because the kernel image is too big for the bootloader
to boot. This commit works around this by decreasing the lzma dictionary
size option from the default 23 to 10.
Before this change the current OpenWrt snapshot image (uncompressed
kernel size 4875139 bytes) failed to boot, while now an even bigger
image (kernel 4.19 with snapshot default config; uncompressed kernel
size 5162833 bytes) boots just fine.
The highest lzma dictionary size option this image booted with was 11.
10 was chosen to have a bit more room for growth.
An unavoidable side-effect of this change is that the compressed kernel
image will take up more space.
Total image size with different dictionary size options:
D23 - 3973903 bytes (base)
D16 - 4113167 bytes (+3.5% - +139264 bytes)
D12 - 4317967 bytes (+8.7% - +344064 bytes)
D11 - 4383503 bytes (+10.3% - +409600 bytes)
D10 - 4461327 bytes (+12.3% - +487424 bytes)
Fixes: FS#1484
Signed-off-by: Mason Clarke <mclarke2355@gmail.com>
78cd384 Update README and patchlevel.h for 2.4.8 release
5d03403 pppd: Avoid use of strnlen (and strlen) in vslprintf
a1e950a pppd: Fix IPv6 default route code for Solaris
ca5e61b plugins/rp-pppoe: Make tag parsing loop condition more accurate
c10c3c7 pppd: Make sure word read from options file is null-terminated
b311e98 pppd: Limit memory accessed by string formats with max length specified
3ea9de9 pppd: Eliminate some more compiler warnings
57edb1a pppd: Include time.h header before using time_t
09f695f pppd: Don't free static string
03104ba pppd.h: Add missing headers
388597e pppd: Add defaultroute6 and related options
66ce4ba pppd: Avoid declarations within statements in main.c
5637180 pppd: Fix `ifname` option in case of multilink (#105)
d00f8a0 pppd: Fix variable reference syntax in Makefile.linux
b6b4d28 pppd: Check tdb pointer before closing
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
If CONFIG_DROPBEAR_ZLIB is set, building fails at the packaging stage
due to an undeclared dependency on libz.so.1.
As is already done for the main dropbear package, conditionally add a
dependency on zlib.
Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
Both devices are available in 64M and 128M RAM configurations but there
is no visial indication which configuration one might get.
So just to be sure we properly support both configurations switch to
kmod-atk10k-ct-smallbuffers.
Signed-off-by: Christoph Krapp <achterin@googlemail.com>
It seems the buildbots can't handle it.
Added a cmake option to find the cxxabi files as they are part of the
toolchain and not in the normal path. It doesn't seem to make a
difference, just gets rid of cmake warnings.
Added another small GCC warning fix. It's fairly minor.
This has no change in compiled size, and most likely no change in
behavior. Bumped the PKG_RELEASE anyway.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Currently the patch only changes break to use goto statement instead.
But not necessary acutually since the ret value checked after the for loop.
So it is okay for the break case before changed by the patch also.
This patch only reverts the following commit partially.
https://github.com/openwrt/openwrt/commit/ddc11c3932c7b7b7df7d5fbd48f207e7
Note: The changes are mainly applied into the linux kernel upstream.
Signed-off-by: Tokunori Ikegami <ikegami.t@gmail.com>
Cc: Koen Vandeputte <koen.vandeputte@ncentric.com>
Currently the patch only changes break to use goto statement instead.
But not necessary acutually since the ret value checked after the for loop.
So it is okay for the break case before changed by the patch also.
This patch only reverts the following commit partially.
ddc11c3932
Note: The changes are mainly applied into the linux kernel upstream.
Signed-off-by: Tokunori Ikegami <ikegami.t@gmail.com>
Cc: Koen Vandeputte <koen.vandeputte@ncentric.com>
These two hacks are no longer necessary as they've
been moved to a special variant of kmod-ath10k-ct.
So, if you have a device suffering from low-memory
situation and getting applications crashes due to
the OOM reaper or kernel panics with ath10k, please
use the "kmod-ath10k-ct-smallbuffers" package from
now on.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Images generated for the TP-Link RE200v1 cannot be updated using
sysupgrade, because a necessary call to append-metadata was missing.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Edimax RA21S is a dual band 11ac router,
based on MediaTek MT7621A and MT7615N chips.
Specification:
- SoC: MediaTek MT7621A dual-core @ 880MHz
- RAM: 256M (Nanya NT5CC128M16IP)
- FLASH: 16MB (Macronix MX25L12835F)
- WiFi: 2.4/5 GHz 4T4R
- 2.4GHz MediaTek MT7615N bgn
- 5GHz MediaTek MT7615N nac
- Switch: SoC integrated Gigabit Switch (4 x LAN, 1 x WAN)
- USB: No
- BTN: Reset, WPS
- LED: 4 red LEDs, indistinguishable when case closed
- UART: through-hole on PCB.
J1: 3.3V - RX - GND - TX / 57600-8N1. 3.3V is the square pad
Installation:
Update the factory image via the OEM web-interface
(by default: http://192.168.2.1/)
User: admin
Password: 1234
The sysupgrade image can be installed via TFTP
from the U-Boot bootloader. Connect via ethernet port 2.
Tested on device by @UAb5eSMn
Signed-off-by: Maksym Medvedev <redrathnure@gmail.com>
[split DTS and take over improvements from RG21S, extend commit
message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
330-MIPS-kexec-Accept-command-line-parameters-from-users.patch causes
problems when building with -Werror=unused-result.
arch/mips/kernel/machine_kexec.c: In function 'machine_kexec_init_argv':
arch/mips/kernel/machine_kexec.c:76:2: error: ignoring return value of 'copy_from_user', declared with attribute warn_unused_result [-Werror=unused-result]
copy_from_user(kexec_argv_buf, buf, size);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Fix this by handling the return value in an appropriate way.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
iperf2 is useful for testing UDP over multicast, add an option to permit
the enabling/disabling of multicast support.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
CONFIG_PINCTRL_SUN4I_A10 controls both the A10 and the A20 enablong of
the pinctrl driver, this is necessary since upstream commit
5d8d349618a9464714c07414c5888bfd9416638f ("pinctrl: sunxi: add A20
support to A10 driver") which has been included in v4.13 and onwards.
Fixes: ad2b3bf310 ("sunxi: Add support for kernel 4.14")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Shared base-files package contains functions for LED migration that
are already used by several targets. Apply those also to lantiq and
drop the (redundant) local code.
While at it, reorder board names in file.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The only device in samsung target is meant to be built with s5pv210
subtarget. Thus, though this won't make a difference for a
one-subtarget target, already add the condition to the Makefile to
make the assignment obvious.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch changes the samsung target to calculate the DTS file name
from vendor and device name and the SOC (i.e. subtarget) following
the common scheme:
soc_vendor_model.dts
This also updates the device definition name to make compatible,
image name, menuconfig name and DTS name consistent.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The TP-Link Archer C20i previously had a generic Ralink MAC address set
for both radios, as the caldata does only contain a generic MAC address.
Set the MAC address from the vendor firmware for both radios to assign
unique MAC addresses to every device.
Signed-off-by: David Bauer <mail@david-bauer.net>
Daniel Golle
Hauke Mehrtens
Yong-hyu Ban
Adrian Schmutzler
Jack Chen
Andrea Dalla Costa
Mason Clarke
DENG Qingfang
Matt Merhar
Christoph Krapp
Rosen Penev
Bjørn Mork
Josef Schlehofer
Tokunori Ikegami
Christian Lamparter
Jo-Philipp Wich
Petr Štetiar
Andreas Böhler
Maksym Medvedev
Florian Fainelli
David Bauer
Moritz Warning