Without the model-based devicename for LEDs, there are still cases
where a third component is required, typically when it refers to
internal "devices" like phys etc. An example are the following two
found on ramips:
- rt2800soc-phy0::radio
- rt2800pci-phy0::radio
So far, the rt2800*-phy: prefixes would be removed by the devicename
removal ("migration") script, and the configuration for these LEDs
would be broken.
To address this, this patch allows to add arguments to a call of
remove_devicename_leds, which will be compared against the first
part of the LED names/labels, and then be ignored by the routine,
and thus not removed:
remove_devicename_leds "rt2800soc-phy0" "rt2800pci-phy0"
This mechanism is supposed to be used when a "devicename" applies
to several devices. If only a single device is affected, it might
be more effective to use a case statement and exclude the device
from migration by that entirely.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Currently, we request LED labels in OpenWrt to follow the scheme
modelname:color:function
However, specifying the modelname at the beginning is actually
entirely useless for the devices we support in OpenWrt. In patches
subsequent to this one, we will thus remove the modelname from
the label definitions on various targets.
To migrate the existing definitions from older installations,
a migration script needs to be deployed that does
modelname:color:function -> color:function
e.g.
dir-789:green:status -> green:status
This patch introduces two functions that do exactly that:
For each entry in /etc/config/system, the routine will check whether
two (or more) colons are present, and then remove everything up to
(and including) the first colon.
For now, this will be applied unconditionally, i.e. if the function
is called for a device, all labels will be cut like this.
However, for a future case of mixed three-part and two-part labels,
it should not be too hard to provide a function argument with
exceptions to the removal.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
vconfig has been disabled by default since 2015 [1] and there are
no remaining uses in entire OpenWrt trunk. However, we still set up
a specific name_type for it during boot.
While this setup is properly implemented to be only triggered when
vconfig is present, it still seems anachronistic and unnecessary
to set up a standard for a tool that is not used anymore.
Therefore, this removes the set_name_type initialization and leaves
it for those people actually using the tool to configure it as needed.
[1] 899a23227e ("busybox: improve applets & deprecate ifconfig, route")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Set the default state for LEDs to off. When a trigger is set, the
trigger will turn the LED automatically on.
Currently LEDs might stay on, e.g. when the LED trigger is set to a
netdev trigger and the interface is never activated or the 'none'
trigger is selected without setting the 'default' option to 0 and it's
set for the LED indicating the system running state.
Using off as a default value is also consistent with the documentation
in the OpenWrt wiki.
Signed-off-by: David Bauer <mail@david-bauer.net>
The LED's "label" property has been deprecated in upstream by:
|commit c5d18dd6b64e09dd6984bda9bdd55160af537a8c
|Author: Jacek Anaszewski <jacek.anaszewski@gmail.com>
|Date: Sun Jun 9 20:19:04 2019 +0200
|
| dt-bindings: leds: Add properties for LED name construction
|
| Introduce dedicated properties for conveying information about
| LED function and color. Mark old "label" property as deprecated.
|
| Additionally function-enumerator property is being provided
| for the cases when neither function nor color can be used
| for LED differentiation.
in order to be somewhat prepared, this patch adds a fallback
as a last resort to make the current led code work by falling
back to the node-name as the "label".
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Fix typo in comment.
Signed-off-by: Walter Sonius <walterav1984@gmail.com>
[commit title/message facelift]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The variable VERSION_REPO is used by opkg to download package(list)s.
Now that the default installation support encrypted HTTP opkg should
make use of it.
Suggested-by: Petr Štetiar <ynezz@true.cz>
Suggested-by: Baptiste Jonglez <baptiste@bitsofnetworks.org>
Signed-off-by: Paul Spooren <mail@aparcar.org>
Acked-by: Baptiste Jonglez <baptiste@bitsofnetworks.org>
Bump PKG_RELEASE for the affected packages as replacing "which" by
"command -v" represents a content change.
Fixes: 1fdf6b745c ("treewide: replace `which` with `command -v`")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Fix shellcheck SC2230
> which is non-standard. Use builtin 'command -v' instead.
Using `command -v` is POSIX compliant while `which` is not. Also to
mention, `command -v` is a shell builtin whereas `which` is a separate
busybox applet.
Once applied to everything concerning OpenWrt we can disable the busybox
feature `which` and save 3.8kB.
Acked-by: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Paul Spooren <mail@aparcar.org>
[also replace cases in zram-swap]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
When passing a section or option value to config_get() which contains
characters that happen to be valid variable interpolation expressions,
the function returns a nonsensical expression result instead of the
expected empty string.
When the passed section or option name contains other characters which
are not valid within a shell variable name, a substitution error is
occuring instead.
The issue can be easily reproduced by one of the following examples:
root@OpenWrt:~# . /lib/functions.sh
root@OpenWrt:~# config load system
root@OpenWrt:~# config_get variable invalid-section option
root@OpenWrt:~# echo "$variable"
section_option:-
root@OpenWrt:~# . /lib/functions.sh
root@OpenWrt:~# config load system
root@OpenWrt:~# config_get variable section invalid-option
root@OpenWrt:~# echo "$variable"
option:-
root@OpenWrt:~# . /lib/functions.sh
root@OpenWrt:~# config load system
root@OpenWrt:~# config_get variable section invalid@option
-ash: eval: syntax error: bad substitution
Fix this issue by only performing interpolations when the given section
and option arguments are free of illegal characters.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Explicitly mount the BPF filesystem if available. This is used for pinning
eBPF programs and maps, making them accessible to other eBPF programs or
from userspace with the help of libbpf or bpftool.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
[daniel@makrotopia.org: bumped PKG_RELEASE]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
So far, the compatibility mechanism only works if both device and
image are already updated to the new routines. This patch extends
the sysupgrade metadata and fwtool_check_image() to account for
"older" images as well:
The basic mechanism for older devices to check for image compatibility
is the supported_devices entry. This can be exploited by putting
a custom message into this variable of the metadata, so older FW
will produce a mismatch and print the message as it thinks it's the
list of supported devices. So, we have two cases:
device 1.0, image 1.0:
The metadata will just contain supported_devices as before.
device 1.0, image 1.1:
The metadata will contain:
"new_supported_devices":["device_string1", "device_string2", ...],
"supported_devices":["Image version 1.1 incompatible to device: ..."]
If the device is "legacy", i.e. does not have the updated fwtool.sh,
it will just fail with image check and print the content of
supported_devices. If DEVICE_COMPAT_MESSAGE is set, this will be
printed on old devices as well through the same mechanism. Otherwise
a generic "Please check documentation ..." is appended.
Upgrade can still be performed with -F like when
SUPPORTED_DEVICES has been removed to prevent bricking.
If the device has updated fwtool.sh (but is 1.0), it will just use
the new_supported_devices instead, and work as intended (flashing
with -n will work, flashing without will print the appropriate
warning).
This mechanism should provide a fair tradeoff between simplicity
and functionality.
Since we touched a lot of fields in metadata, this also bumps
metadata_version to 1.1.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
We regularly encounter the situation that devices are subject to
changes that will make them incompatible to previous versions.
Removing SUPPORTED_DEVICES will not really be helpful in most of these
cases, as this only helps after a rename.
To solve this situation, this patchset introduces a compatibility
version for devices. In this patch, the actual checks are implemented
into fwtool_check_image():
If an incompatible change is introduced, one can increase either
the minor version (1.0->1.1) or the major version (1.0->2.0).
Minor version increment:
This will still allow sysupgrade, but require to reset config
(-n or SAVE_CONFIG=0). If sysupgrade is called without -n, a
corresponding message will be printed. If sysupgrade is called
with -n, it will just pass, with supported devices being checked
as usual. (Which will allow us to add back SUPPORTED_DEVICES for
many cases.)
Major version increment:
This is meant for potential (rare) cases where sysupgrade is
not possible at all, because it would break the device.
In this case, a warning will be printed, and -n won't help.
If image check fails because of one of the versions parts not
matching, the content of DEVICE_COMPAT_MESSAGE is printed in
addition to the generic message (if set).
For both cases, upgrade can still be forced with -F as usual.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
We regularly encounter the situation that devices are subject to
changes that will make them incompatible to previous versions.
Removing SUPPORTED_DEVICES will not really be helpful in most of these
cases, as this only helps after a rename.
To solve this situation, this patchset introduces a compatibility
version for devices. To complement the DEVICE_COMPAT_VERSION set
for the image to be flashed, this implements a compat_version on
the device, so it will have something to compare with the image.
The only viable way to achieve this seems to be via board.d files,
i.e. this is technically adding a compat version for the device's
config.
Like for the network setup, this will set up a command
ucidef_set_compat_version to set the compat_version in board.d.
This will then add a string to /etc/board.json, which will be
translated into uci system config by bin/config_generate.
By this, the compat_version, being a version of the config, will
also be exposed to the user.
As with DEVICE_COMPAT_VERSION, missing uci entry will be assumed
as compat_version "1.0", so we only need to add this if a device
needs to be bumped, e.g.
ucidef_set_compat_version "1.1"
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This adds a function for generating a valid random MAC address (unset MC
bit / set locally administered bit).
It is necessary for devices which do not have a MAC address programmed
by the manufacturer.
Signed-off-by: David Bauer <mail@david-bauer.net>
This replaces deprecated backticks by more versatile $(...) syntax.
This does not touch lib/upgrade/nand.sh, as there replacement is
not trivial.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Some devices (e.g. Arduino Yun) need bitwise operations during MAC address
setup. This commit adds generalized versions of macaddr_setbit_la(), which
are helpful when manipulating a single bit in a MAC address.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
With package "coreutil-sha256sum" installed "sysupgrade" fails to perform 'sha256sum -s' and instead returns 'invalid option -- 's''.
This is caused due to:
different syntax for a sha256sum status check ('sha256sum --status' with "coreutil-sha256sum")
'/usr/bin/sha256sum' being symlinked to '/usr/bin/gnu-sha256sum' (after installation of "coreutil-sha256sum")
"coreutil-sha256sum" package from the packages feed replaces the Busybox sha256sum
This patch restores for 'sysupgrade' the busybox call to its sha256sum applet.
Signed-off-by: Huangbin Zhan <zhanhb88@gmail.com>
urandom-seed has a separate Makefile, we can safely remove the definition here.
Fixes: 27bfde9c9f ("base-files: move urandom seed bits into separate package")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Previously, gpio_switch only accepts GPIO pin number as input. Once a
GPIO pin is exported and named by device tree, its pin state cannot be
configured and saved across reboots by UCI.
This patch adds support for named GPIO pins. Thus GPIO pin can be
exported by device tree with active high/low correctly configured,
having human-readable name in /sys/class/gpio/ is also now possible.
More importantly, GPIO pins which are referenced by name will be immune
from pin mapping breakage while unintentional pin number changes are
introduced by kernel or driver updates.
Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
Due to filesystem write caching the old configuration data could stay
out of flash for a long time during a first boot after the sysupgrade.
Power loss during this period could damage the overlay data and even
make device inaccessable via the network.
Fix this by syncing data to a flash as soon as the previous
configuration will be unpacked after the sysupgrade. Also sync the FS
state after the sysupgrade.tgz archive removing to prevent duplicative
extraction of a previous configuration.
Tested with AMD Geode based board.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
This changes the ide-disk LED trigger to the generic disk-activity as
ide-disk trigger was removed in upstream commit eb25cb9956cc ("leds:
convert IDE trigger to common disk trigger").
Signed-off-by: Thomas Albers <thomas.gameiro@googlemail.com>
[split into separate commit, commit description facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
tl;dr: dd will silently truncate the output if reading from special
files (e.g. sysfs attributes) with a too large bs parameter.
This problem was exposed on some RouterBOARD ipq40xx devices which use a
caldata payload which is larger than PAGE_SIZE, contrary to all other
currently supported RouterBOARD devices: the caldata would fail to
properly load with the current scripts.
Background: dd doesn't seem to correctly handle read() results that
return less than requested data. sysfs attributes have a kernel exchange
buffer which is at most PAGE_SIZE big, so only 1 page can be read() at a
time. In this case, if bs is larger than PAGE_SIZE, dd will silently
truncate blocks to PAGE_SIZE. With the current scripts using bs=<size>
count=1, the data is truncated to PAGE_SIZE as soon as the requested
<size> exceeds this value.
This commit works around this problem by using `cat` in the caldata
routines that can read from a file (routines that read from mtd devices
are untouched). cat correctly handles partial read requests. The output
is then piped to dd with the same parameters as before, to ensure that
the resulting file remains exactly the same.
This is a simple workaround, the downside is that it uses a pipe and one
more executable, and therefore has a larger memory footprint and is
slower. This is deemed acceptable considering these routines are only
used at boot time.
Tested-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Use same indent as for the rest of the file.
Signed-off-by: Javier Marcet <javier@marcet.info>
[add commit description]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This will enable platforms to extract caldata to an arbitrary file,
or patch mac in an abitrary file.
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
As touch creates files with permission 0644 use umask to create
config files with permission 0600 to be inline with INSTALL_CONF
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Including the local build key in /etc/opkg/keys isn't feasible when
building on the buildbot: The included key collides with its copy
already in openwrt-keyring which breaks the ImageBuilder.
Not including a locally generated key also makes the base-files package
more reproducible.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
current preinit code in base-files doesn't config switch when there are
no port roles defined. But this kind of configuration exists on single
port devices where switch vlan is simply disabled.
configure reset and enable_vlan property when a switch node exist.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
The file /lib/functions/system.sh depends on find_mtd_index() and
find_mtd_part() located in /lib/function.sh, so let's source that
file.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The default_postinst() function in /lib/functions.sh sources
/lib/functions/system.sh before cycling through uci-defaults files.
This creates a pseudo-cyclic dependency as system.sh also uses
functions that are located in functions.sh. Despite that, there
is actually only one uci-defaults file in the entire repo that needs
system.sh, and this one contains an explicit source for system.sh
anyway.
Consequently, this patch removes the sourcing of system.sh in
functions.sh. There are no relevant uses in packages, routing and
luci repositories.
This may require adjustments for downstream, though.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Add EFI platform bootable images for x86 platforms. These images can
also boot from legacy BIOS platform.
EFI System Partition need to be fat12/fat16/fat32 (not need to load
filesystem drivers), so the first partition of EFI images are not ext4
filesystem any more.
GPT partition table has an alternate partition table, we did not
generate it. This may cause problems when use these images as qemu disk
(kernel can not find rootfs), we pad enough sectors will be ok.
Signed-off-by: 李国 <uxgood.org@gmail.com>
[part_magic_* refactoring, removed genisoimage checks]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Because /etc/profile (and ~/.profile) are read by login shells only,
aliases and functions defined there are not available to non-login
shells, e.g. when using screen or tmux.
If the ENV environment variable exists (exported by /etc/profile or
~/.profile) and references an existing file, then all interactive shells
(login or non-login) will read that file as well.
This sets the ENV environment variable in /etc/profile, pointing to
/etc/shinit.
This also adds /etc/shinit, which:
* Contains alias and function definitions originally in /etc/profile
* Sources /etc/mkshrc if the user is using mksh (also originally in
/etc/profile), as /etc/mkshrc is meant for all interactive shells
* Sources ~/.mkshrc if the user is using mksh, to compensate for the
fact that mksh will not read ~/.mkshrc if ENV is set
* Sources ~/.shinit if the user is not using mksh
This also removes the shebang from /etc/profile, as the file is sourced,
not executed.
Signed-off-by: Jeffery To <jeffery.to@gmail.com>
CONFIG_INCLUDE_CONFIG option is helpful for being able to rebuild the
exact same firmware as you see on a live OpenWRT instance, but it's
crucially missing feeds information, so we can't rebuild the exact same
package versions. This commit fixes this by adding the remaining feeds
(and version) buildinfo files to the image.
Signed-off-by: Xu Wang <xwang1498@gmx.com>
For devices without a dedicated 'diag' LED, we use sometimes one of
other LEDs for indicating at least 'boot', 'failsafe' and 'upgrade'
stages. In some cases, at the same time these LEDs have defined default
triggers in DTS using 'linux,default-trigger' property. Current 'diag'
setup removes the trigger and turns off 'boot' LED after bootup.
One of the examples of such device is TP-Link TL-WR841N v14 (ramips)
which uses 'wlan' LED with defined 'linux,default-trigger' for 'diag':
aliases {
led-boot = &led_wlan;
led-failsafe = &led_wlan;
led-upgrade = &led_wlan;
};
[...]
led_wlan: wlan {
label = "tl-wr841n-v14:green:wlan";
gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
linux,default-trigger = "phy0tpt";
};
This patch extends 'diag.sh' and 'leds.sh' scripts to make sure default
trigger defined in DTS is restored for 'diag' LED which isn't used for
indicating 'running' stage.
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This change makes the names of Broadcom targets consistent by using
the common notation based on SoC/CPU ID (which is used internally
anyway), bcmXXXX instead of brcmXXXX.
This is even used for target TITLE in make menuconfig already,
only the short target name used brcm so far.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
"[[" is a bash extension for test. As the ash-implementation is
not fully compatible we drop its usage.
Also change to "=" for simple test, which is sufficient. (see d6ac8ca76c)
Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
[split patch, removed shebang]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
It's cleaner and faster as it does not need to do extra work.
Also removed $() to avoid executing the output. The shell can handle it.
https://github.com/koalaman/shellcheck/wiki/SC2143
Signed-off-by: Rosen Penev <rosenp@gmail.com>
[correct || to && for one conversion]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler
David Bauer
Christian Lamparter
Walter Sonius
Paul Spooren
Jo-Philipp Wich
Tony Ambardar
Rosen Penev
Sungbo Eo
Huangbin Zhan
Kuan-Yi Li
Sergey Ryazanov
Thomas Albers
Thibaut VARÈNE
Álvaro Fernández Rojas
Javier Marcet
Hans Dedecker
Alexander Couzens
Daniel Golle
Chuanhong Guo
Florian Eckert
Kevin Darbyshire-Bryant
李国
Jeffery To
Xu Wang
Piotr Dymacz
Sven Roederer