ath79: add support for Buffalo WZR-HP-AG300H
Buffalo WZR-HP-AG300H is a dual band router based on
Qualcom Atheros AR7161 rev 2
Specification:
- 680 MHz CPU (Qualcomm Atheros AR7161)
- 128 MiB RAM (2x Samsung K4H511638G-LCCC)
- 32 MiB Flash (2x Winbond 25Q128BVFG)
- WiFi 5 GHz a/n (Atheros AR9220)
- WiFi 2.4 GHz b/g/n (Atheros AR9223)
- 1000Base-T WAN (Atheros AR7161)
- 4x 1000Base-T Switch (Atheros AR8316)
- 1x USB 2.0
- 3 Buttons (AOSS/WPS, Reset, USB Eject)
- 2 Slide switches (Router (on/off/auto), Movie Engine (on/off))
- 9 LEDs (Power green, WLAN 2GHz green, WLAN 2GHz amber,
WLAN 5GHz green, WLAN 5GHz LED amber, Router green,
Diag red, Movie Engine blue, USB green)
It is already supported by the ar71xx target.
For more information on the device visit the wiki:
<https://openwrt.org/toh/buffalo/wzr-hp-ag300h>
Serial console:
- The UART Header is next to Movie Engine Switch.
- Pinout is RX - TX - GND - 3.3V (Square Pad is 3.3V)
- The Serial setting is 115200-8-N-1.
Installation of OpenWRT from vendor firmware:
- Connect to the Web-interface at http://192.168.11.1
- Go to “Administration” → “Firmware Upgrade”
- Upload the OpenWrt factory image
Tested:
- Ethernet (LAN, WAN)
- WiFi
- Installation
- via TFTP rescue
- via factory image
- on firmware v1.77 (28-05-2012)
- on pro firmware v24SP2 r30356 (26-03-2018)
- via sysupgrade from ar71xx
(wlan devices don't work because of new names)
- via sysupgrade from itself
- Buttons
- LEDS
- USB (Power control and device recognition)
Signed-off-by: Bernhard Frauendienst <openwrt@nospam.obeliks.de>
2018-08-18 16:28:02 +00:00
|
|
|
include ./common-buffalo.mk
|
2018-06-13 08:51:51 +00:00
|
|
|
include ./common-netgear.mk
|
2018-03-02 18:28:50 +00:00
|
|
|
|
2018-09-04 21:27:02 +00:00
|
|
|
DEVICE_VARS += ADDPATTERN_ID ADDPATTERN_VERSION
|
2018-12-29 09:22:32 +00:00
|
|
|
DEVICE_VARS += SEAMA_SIGNATURE SEAMA_MTDBLOCK
|
2018-12-31 15:41:07 +00:00
|
|
|
DEVICE_VARS += KERNEL_INITRAMFS_PREFIX
|
2018-09-04 21:27:02 +00:00
|
|
|
|
|
|
|
define Build/cybertan-trx
|
|
|
|
@echo -n '' > $@-empty.bin
|
|
|
|
-$(STAGING_DIR_HOST)/bin/trx -o $@.new \
|
|
|
|
-f $(IMAGE_KERNEL) -F $@-empty.bin \
|
|
|
|
-x 32 -a 0x10000 -x -32 -f $@
|
|
|
|
-mv "$@.new" "$@"
|
|
|
|
-rm $@-empty.bin
|
|
|
|
endef
|
|
|
|
|
|
|
|
define Build/addpattern
|
|
|
|
-$(STAGING_DIR_HOST)/bin/addpattern -B $(ADDPATTERN_ID) \
|
|
|
|
-v v$(ADDPATTERN_VERSION) -i $@ -o $@.new
|
|
|
|
-mv "$@.new" "$@"
|
|
|
|
endef
|
|
|
|
|
2018-12-31 15:41:07 +00:00
|
|
|
define Build/add-elecom-factory-initramfs
|
|
|
|
$(eval edimax_model=$(word 1,$(1)))
|
|
|
|
$(eval product=$(word 2,$(1)))
|
2018-09-10 07:30:28 +00:00
|
|
|
|
2018-12-31 15:41:07 +00:00
|
|
|
$(STAGING_DIR_HOST)/bin/mkedimaximg \
|
|
|
|
-b -s CSYS -m $(edimax_model) \
|
|
|
|
-f 0x70000 -S 0x01100000 \
|
|
|
|
-i $@ -o $@.factory
|
|
|
|
|
|
|
|
( \
|
|
|
|
echo -n -e "ELECOM\x00\x00$(product)" | dd bs=40 count=1 conv=sync; \
|
|
|
|
echo -n "0.00" | dd bs=16 count=1 conv=sync; \
|
|
|
|
dd if=$@.factory; \
|
|
|
|
) > $@.factory.new
|
|
|
|
|
|
|
|
if [ "$$(stat -c%s $@.factory.new)" -le $$(($(subst k,* 1024,$(subst m, * 1024k,$(IMAGE_SIZE))))) ]; then \
|
|
|
|
mv $@.factory.new $(BIN_DIR)/$(KERNEL_INITRAMFS_PREFIX)-factory.bin; \
|
|
|
|
else \
|
|
|
|
echo "WARNING: initramfs kernel image too big, cannot generate factory image" >&2; \
|
|
|
|
fi
|
2018-09-10 07:30:28 +00:00
|
|
|
endef
|
|
|
|
|
2018-12-08 06:18:17 +00:00
|
|
|
define Build/nec-fw
|
|
|
|
( stat -c%s $@ | tr -d "\n" | dd bs=16 count=1 conv=sync; ) >> $@
|
|
|
|
( \
|
|
|
|
echo -n -e "$(1)" | dd bs=16 count=1 conv=sync; \
|
|
|
|
echo -n "0.0.00" | dd bs=16 count=1 conv=sync; \
|
|
|
|
dd if=$@; \
|
|
|
|
) > $@.new
|
|
|
|
mv $@.new $@
|
|
|
|
endef
|
|
|
|
|
2018-12-29 09:22:32 +00:00
|
|
|
define Device/seama
|
|
|
|
KERNEL := kernel-bin | append-dtb | relocate-kernel | lzma
|
|
|
|
KERNEL_INITRAMFS := $$(KERNEL) | seama
|
|
|
|
IMAGES += factory.bin
|
|
|
|
SEAMA_MTDBLOCK := 1
|
|
|
|
|
|
|
|
# 64 bytes offset:
|
|
|
|
# - 28 bytes seama_header
|
|
|
|
# - 36 bytes of META data (4-bytes aligned)
|
|
|
|
IMAGE/default := append-kernel | pad-offset $$$$(BLOCKSIZE) 64 | append-rootfs
|
|
|
|
IMAGE/sysupgrade.bin := \
|
|
|
|
$$(IMAGE/default) | seama | pad-rootfs | append-metadata | check-size $$$$(IMAGE_SIZE)
|
|
|
|
IMAGE/factory.bin := \
|
|
|
|
$$(IMAGE/default) | pad-rootfs -x 64 | seama | seama-seal | check-size $$$$(IMAGE_SIZE)
|
|
|
|
SEAMA_SIGNATURE :=
|
|
|
|
endef
|
|
|
|
|
2018-03-02 18:28:50 +00:00
|
|
|
define Device/avm_fritz300e
|
|
|
|
ATH_SOC := ar7242
|
|
|
|
DEVICE_TITLE := AVM FRITZ!WLAN Repeater 300E
|
|
|
|
KERNEL := kernel-bin | append-dtb | lzma | eva-image
|
|
|
|
KERNEL_INITRAMFS := $$(KERNEL)
|
|
|
|
IMAGE_SIZE := 15232k
|
|
|
|
IMAGE/sysupgrade.bin := append-kernel | pad-to 64k | \
|
|
|
|
append-squashfs-fakeroot-be | pad-to 256 | \
|
|
|
|
append-rootfs | pad-rootfs | append-metadata | check-size $$$$(IMAGE_SIZE)
|
|
|
|
DEVICE_PACKAGES := fritz-tffs rssileds -swconfig
|
|
|
|
endef
|
|
|
|
TARGET_DEVICES += avm_fritz300e
|
|
|
|
|
ath79: add support for Fritz!Box 4020
This commit adds support for the AVM Fritz!Box 4020 WiFi-router.
SoC: Qualcomm Atheros QCA9561 (Dragonfly) 750MHz
RAM: Winbond W971GG6KB-25
FLASH: Macronix MX25L12835F
WiFi: QCA9561 b/g/n 3x3 450Mbit/s
USB: 1x USB 2.0
IN: WPS button, WiFi button
OUT: Power LED green, Internet LED green, WLAN LED green,
LAN LED green, INFO LED green, INFO LED red
UART: Header Next to Black metal shield
Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V)
The Serial setting is 115200-8-N-1.
Tested and working:
- Ethernet (LAN + WAN)
- WiFi (correct MAC)
- Installation via EVA bootloader
- OpenWRT sysupgrade
- Buttons
- LEDs
The USB port doesn't work. Both Root Hubs are detected as having 0 Ports:
[ 3.670807] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 3.723267] usbcore: registered new interface driver usbfs
[ 3.729058] usbcore: registered new interface driver hub
[ 3.734616] usbcore: registered new device driver usb
[ 3.744181] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.758357] SCSI subsystem initialized
[ 3.766026] ehci-platform: EHCI generic platform driver
[ 3.771548] ehci-platform ehci-platform.0: EHCI Host Controller
[ 3.777708] ehci-platform ehci-platform.0: new USB bus registered, assigned bus number 1
[ 3.788169] ehci-platform ehci-platform.0: irq 48, io mem 0x1b000000
[ 3.816647] ehci-platform ehci-platform.0: USB 2.0 started, EHCI 0.00
[ 3.824001] hub 1-0:1.0: USB hub found
[ 3.828219] hub 1-0:1.0: config failed, hub doesn't have any ports! (err -19)
[ 3.835825] ehci-platform ehci-platform.1: EHCI Host Controller
[ 3.842009] ehci-platform ehci-platform.1: new USB bus registered, assigned bus number 2
[ 3.852481] ehci-platform ehci-platform.1: irq 49, io mem 0x1b400000
[ 3.886631] ehci-platform ehci-platform.1: USB 2.0 started, EHCI 0.00
[ 3.894011] hub 2-0:1.0: USB hub found
[ 3.898190] hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19)
[ 3.908928] usbcore: registered new interface driver usb-storage
[ 3.915634] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
A few words about the shift-register:
AVM used a trick to control the shift-register for the LEDs with only 2
pins, SERCLK and MOSI. Q7S, normally used for daisy-chaining multiple
shift-registers, pulls the latch, moving the shift register-state to
the storage register. It also pulls down MR (normally pulled up) to
clear the storage register, so the latch gets released and will not be
pulled by the remaining bits in the shift-register. Shift register is
all-zero after this.
For that we need to make sure output 7 is set to high on driver probe.
We accomplish this by using gpio-hogging.
Installation via EVA:
In the first seconds after Power is connected, the bootloader will
listen for FTP connections on 169.254.157.1 (Might also be 192.168.178.1).
Firmware can be uploaded like following:
ftp> quote USER adam2
ftp> quote PASS adam2
ftp> binary
ftp> debug
ftp> passive
ftp> quote MEDIA FLSH
ftp> put openwrt-sysupgrade.bin mtd1
Note that this procedure might take up to two minutes. After transfer is
complete you need to powercycle the device to boot OpenWRT.
Signed-off-by: David Bauer <mail@david-bauer.net>
2018-08-18 16:30:46 +00:00
|
|
|
define Device/avm_fritz4020
|
|
|
|
ATH_SOC := qca9561
|
|
|
|
DEVICE_TITLE := AVM FRITZ!Box 4020
|
|
|
|
IMAGE_SIZE := 15232k
|
|
|
|
KERNEL := kernel-bin | append-dtb | lzma | eva-image
|
|
|
|
KERNEL_INITRAMFS := $$(KERNEL)
|
|
|
|
IMAGE/sysupgrade.bin := append-kernel | pad-to 64k | \
|
|
|
|
append-squashfs-fakeroot-be | pad-to 256 | \
|
|
|
|
append-rootfs | pad-rootfs | append-metadata | check-size $$$$(IMAGE_SIZE)
|
|
|
|
DEVICE_PACKAGES := fritz-tffs
|
2019-02-23 12:12:49 +00:00
|
|
|
SUPPORTED_DEVICES += fritz4020
|
ath79: add support for Fritz!Box 4020
This commit adds support for the AVM Fritz!Box 4020 WiFi-router.
SoC: Qualcomm Atheros QCA9561 (Dragonfly) 750MHz
RAM: Winbond W971GG6KB-25
FLASH: Macronix MX25L12835F
WiFi: QCA9561 b/g/n 3x3 450Mbit/s
USB: 1x USB 2.0
IN: WPS button, WiFi button
OUT: Power LED green, Internet LED green, WLAN LED green,
LAN LED green, INFO LED green, INFO LED red
UART: Header Next to Black metal shield
Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V)
The Serial setting is 115200-8-N-1.
Tested and working:
- Ethernet (LAN + WAN)
- WiFi (correct MAC)
- Installation via EVA bootloader
- OpenWRT sysupgrade
- Buttons
- LEDs
The USB port doesn't work. Both Root Hubs are detected as having 0 Ports:
[ 3.670807] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 3.723267] usbcore: registered new interface driver usbfs
[ 3.729058] usbcore: registered new interface driver hub
[ 3.734616] usbcore: registered new device driver usb
[ 3.744181] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.758357] SCSI subsystem initialized
[ 3.766026] ehci-platform: EHCI generic platform driver
[ 3.771548] ehci-platform ehci-platform.0: EHCI Host Controller
[ 3.777708] ehci-platform ehci-platform.0: new USB bus registered, assigned bus number 1
[ 3.788169] ehci-platform ehci-platform.0: irq 48, io mem 0x1b000000
[ 3.816647] ehci-platform ehci-platform.0: USB 2.0 started, EHCI 0.00
[ 3.824001] hub 1-0:1.0: USB hub found
[ 3.828219] hub 1-0:1.0: config failed, hub doesn't have any ports! (err -19)
[ 3.835825] ehci-platform ehci-platform.1: EHCI Host Controller
[ 3.842009] ehci-platform ehci-platform.1: new USB bus registered, assigned bus number 2
[ 3.852481] ehci-platform ehci-platform.1: irq 49, io mem 0x1b400000
[ 3.886631] ehci-platform ehci-platform.1: USB 2.0 started, EHCI 0.00
[ 3.894011] hub 2-0:1.0: USB hub found
[ 3.898190] hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19)
[ 3.908928] usbcore: registered new interface driver usb-storage
[ 3.915634] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
A few words about the shift-register:
AVM used a trick to control the shift-register for the LEDs with only 2
pins, SERCLK and MOSI. Q7S, normally used for daisy-chaining multiple
shift-registers, pulls the latch, moving the shift register-state to
the storage register. It also pulls down MR (normally pulled up) to
clear the storage register, so the latch gets released and will not be
pulled by the remaining bits in the shift-register. Shift register is
all-zero after this.
For that we need to make sure output 7 is set to high on driver probe.
We accomplish this by using gpio-hogging.
Installation via EVA:
In the first seconds after Power is connected, the bootloader will
listen for FTP connections on 169.254.157.1 (Might also be 192.168.178.1).
Firmware can be uploaded like following:
ftp> quote USER adam2
ftp> quote PASS adam2
ftp> binary
ftp> debug
ftp> passive
ftp> quote MEDIA FLSH
ftp> put openwrt-sysupgrade.bin mtd1
Note that this procedure might take up to two minutes. After transfer is
complete you need to powercycle the device to boot OpenWRT.
Signed-off-by: David Bauer <mail@david-bauer.net>
2018-08-18 16:30:46 +00:00
|
|
|
endef
|
|
|
|
TARGET_DEVICES += avm_fritz4020
|
|
|
|
|
2018-09-11 11:50:35 +00:00
|
|
|
define Device/buffalo_bhr-4grv
|
|
|
|
ATH_SOC := ar7242
|
|
|
|
DEVICE_TITLE := Buffalo BHR-4GRV
|
|
|
|
DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-usb-ledtrig-usbport
|
|
|
|
IMAGE_SIZE := 32256k
|
|
|
|
IMAGES += factory.bin tftp.bin
|
|
|
|
IMAGE/default := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | check-size $$$$(IMAGE_SIZE)
|
2018-10-07 11:37:42 +00:00
|
|
|
IMAGE/factory.bin := $$(IMAGE/default) | buffalo-enc BHR-4GRV 1.99 | buffalo-tag BHR-4GRV 3
|
2018-09-11 11:50:35 +00:00
|
|
|
IMAGE/tftp.bin := $$(IMAGE/default) | buffalo-tftp-header
|
|
|
|
SUPPORTED_DEVICES += wzr-hp-g450h
|
|
|
|
endef
|
|
|
|
TARGET_DEVICES += buffalo_bhr-4grv
|
|
|
|
|
ath79: modify mtd partitions for Buffalo BHR-4GRV2
This commit modifies mtd partitions define for Buffalo BHR-4GRV2 and
move it to generic subtarget.
In Buffalo BHR-4GRV2, "kernel" partition is located behined "rootfs"
partition in the stock firmware. This causes the size of the kernel
to be limited by the fixed value.
0x50000 0xe80000 0xff0000
+-------------------------------+--------------+
| rootfs | kernel |
| (14528k) | (1472k) |
+-------------------------------+--------------+
After ar71xx was updated to Kernel 4.14, the kernel size of BHR-4GRV2
exceeded the limit, and it breaks builds on official buildbot.
Since this issue was also confirmed in ath79, I modified the mtd
partitions to get rid of that limitation.
0x50000 0xff0000
+----------------------------------------------+
| firmware |
| (16000k) |
+----------------------------------------------+
However, this commit breaks compatibility with ar71xx firmware, so I
dropped "SUPPORTED_DEVICES += bhr-4grv2".
This commit requires new flash instruction instead of the old one.
Flash instruction using initramfs image:
1. Connect the computer to the LAN port of BHR-4GRV2
2. Set the IP address of the computer to 192.168.12.10
3. Rename the OpenWrt initramfs image to
"bhr4grv2-uImage-initramfs-gzip.bin" and place it into the TFTP
directory
4. Start the tftp server on the computer
5. While holding down the "ECO" button, connect power cable to
BHR-4GRV2 and turn on it
6. Flashing (orange) diag LED and release the finger from the button,
BHR-4GRV2 downloads the intiramfs image from TFTP server and boot
with it
7. On the initramfs image, create "/etc/fw_env.config" file with
following contents
/dev/mtd1 0x0 0x10000 0x10000
8. Execute following commands to add environment variables for
u-boot
fw_setenv ipaddr 192.168.12.1
fw_setenv serverip 192.168.12.10
fw_setenv ethaddr 00:aa:bb:cc:dd:ee
fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000"
9. Perform sysupgrade with squashfs-sysupgrade image
10. Wait ~150 seconds to complete flashing
And this commit includes small fix; BHR-4GRV2 has QCA9557 as a SoC,
not QCA9558.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
2018-11-06 13:37:43 +00:00
|
|
|
define Device/buffalo_bhr-4grv2
|
|
|
|
ATH_SOC := qca9557
|
|
|
|
DEVICE_TITLE := Buffalo BHR-4GRV2
|
|
|
|
IMAGE_SIZE := 16000k
|
|
|
|
endef
|
|
|
|
TARGET_DEVICES += buffalo_bhr-4grv2
|
|
|
|
|
ath79: add support for Buffalo WZR-HP-AG300H
Buffalo WZR-HP-AG300H is a dual band router based on
Qualcom Atheros AR7161 rev 2
Specification:
- 680 MHz CPU (Qualcomm Atheros AR7161)
- 128 MiB RAM (2x Samsung K4H511638G-LCCC)
- 32 MiB Flash (2x Winbond 25Q128BVFG)
- WiFi 5 GHz a/n (Atheros AR9220)
- WiFi 2.4 GHz b/g/n (Atheros AR9223)
- 1000Base-T WAN (Atheros AR7161)
- 4x 1000Base-T Switch (Atheros AR8316)
- 1x USB 2.0
- 3 Buttons (AOSS/WPS, Reset, USB Eject)
- 2 Slide switches (Router (on/off/auto), Movie Engine (on/off))
- 9 LEDs (Power green, WLAN 2GHz green, WLAN 2GHz amber,
WLAN 5GHz green, WLAN 5GHz LED amber, Router green,
Diag red, Movie Engine blue, USB green)
It is already supported by the ar71xx target.
For more information on the device visit the wiki:
<https://openwrt.org/toh/buffalo/wzr-hp-ag300h>
Serial console:
- The UART Header is next to Movie Engine Switch.
- Pinout is RX - TX - GND - 3.3V (Square Pad is 3.3V)
- The Serial setting is 115200-8-N-1.
Installation of OpenWRT from vendor firmware:
- Connect to the Web-interface at http://192.168.11.1
- Go to “Administration” → “Firmware Upgrade”
- Upload the OpenWrt factory image
Tested:
- Ethernet (LAN, WAN)
- WiFi
- Installation
- via TFTP rescue
- via factory image
- on firmware v1.77 (28-05-2012)
- on pro firmware v24SP2 r30356 (26-03-2018)
- via sysupgrade from ar71xx
(wlan devices don't work because of new names)
- via sysupgrade from itself
- Buttons
- LEDS
- USB (Power control and device recognition)
Signed-off-by: Bernhard Frauendienst <openwrt@nospam.obeliks.de>
2018-08-18 16:28:02 +00:00
|
|
|
define Device/buffalo_wzr-hp-ag300h
|
|
|
|
ATH_SOC := ar7161
|
|
|
|
DEVICE_TITLE := Buffalo WZR-HP-AG300H
|
|
|
|
IMAGE_SIZE := 32256k
|
|
|
|
IMAGES += factory.bin tftp.bin
|
|
|
|
IMAGE/default := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | check-size $$$$(IMAGE_SIZE)
|
2018-10-07 11:37:42 +00:00
|
|
|
IMAGE/factory.bin := $$(IMAGE/default) | buffalo-enc WZR-HP-AG300H 1.99 | buffalo-tag WZR-HP-AG300H 3
|
ath79: add support for Buffalo WZR-HP-AG300H
Buffalo WZR-HP-AG300H is a dual band router based on
Qualcom Atheros AR7161 rev 2
Specification:
- 680 MHz CPU (Qualcomm Atheros AR7161)
- 128 MiB RAM (2x Samsung K4H511638G-LCCC)
- 32 MiB Flash (2x Winbond 25Q128BVFG)
- WiFi 5 GHz a/n (Atheros AR9220)
- WiFi 2.4 GHz b/g/n (Atheros AR9223)
- 1000Base-T WAN (Atheros AR7161)
- 4x 1000Base-T Switch (Atheros AR8316)
- 1x USB 2.0
- 3 Buttons (AOSS/WPS, Reset, USB Eject)
- 2 Slide switches (Router (on/off/auto), Movie Engine (on/off))
- 9 LEDs (Power green, WLAN 2GHz green, WLAN 2GHz amber,
WLAN 5GHz green, WLAN 5GHz LED amber, Router green,
Diag red, Movie Engine blue, USB green)
It is already supported by the ar71xx target.
For more information on the device visit the wiki:
<https://openwrt.org/toh/buffalo/wzr-hp-ag300h>
Serial console:
- The UART Header is next to Movie Engine Switch.
- Pinout is RX - TX - GND - 3.3V (Square Pad is 3.3V)
- The Serial setting is 115200-8-N-1.
Installation of OpenWRT from vendor firmware:
- Connect to the Web-interface at http://192.168.11.1
- Go to “Administration” → “Firmware Upgrade”
- Upload the OpenWrt factory image
Tested:
- Ethernet (LAN, WAN)
- WiFi
- Installation
- via TFTP rescue
- via factory image
- on firmware v1.77 (28-05-2012)
- on pro firmware v24SP2 r30356 (26-03-2018)
- via sysupgrade from ar71xx
(wlan devices don't work because of new names)
- via sysupgrade from itself
- Buttons
- LEDS
- USB (Power control and device recognition)
Signed-off-by: Bernhard Frauendienst <openwrt@nospam.obeliks.de>
2018-08-18 16:28:02 +00:00
|
|
|
IMAGE/tftp.bin := $$(IMAGE/default) | buffalo-tftp-header
|
|
|
|
DEVICE_PACKAGES := kmod-usb-core kmod-usb-ohci kmod-usb2 kmod-usb-ledtrig-usbport kmod-leds-reset kmod-owl-loader
|
|
|
|
SUPPORTED_DEVICES += wzr-hp-ag300h
|
|
|
|
endef
|
|
|
|
TARGET_DEVICES += buffalo_wzr-hp-ag300h
|
|
|
|
|
2018-10-02 13:28:45 +00:00
|
|
|
define Device/buffalo_wzr-hp-g302h-a1a0
|
|
|
|
ATH_SOC := ar7242
|
|
|
|
DEVICE_TITLE := Buffalo WZR-HP-G302H A1A0
|
|
|
|
DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-usb-ledtrig-usbport
|
|
|
|
IMAGE_SIZE := 32128k
|
|
|
|
IMAGES += factory.bin tftp.bin
|
|
|
|
IMAGE/default := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | check-size $$$$(IMAGE_SIZE)
|
|
|
|
IMAGE/factory.bin := $$(IMAGE/default) | buffalo-enc WZR-HP-G302H 1.99 | buffalo-tag WZR-HP-G302H 4
|
|
|
|
IMAGE/tftp.bin := $$(IMAGE/default) | buffalo-tftp-header
|
|
|
|
SUPPORTED_DEVICES += wzr-hp-g300nh2
|
|
|
|
endef
|
|
|
|
TARGET_DEVICES += buffalo_wzr-hp-g302h-a1a0
|
|
|
|
|
2018-08-02 07:14:10 +00:00
|
|
|
define Device/buffalo_wzr-hp-g450h
|
|
|
|
ATH_SOC := ar7242
|
2018-09-11 11:13:17 +00:00
|
|
|
DEVICE_TITLE := Buffalo WZR-HP-G450H/WZR-450HP
|
2018-08-02 07:14:10 +00:00
|
|
|
DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-usb-ledtrig-usbport
|
|
|
|
IMAGE_SIZE := 32256k
|
2018-09-11 11:13:17 +00:00
|
|
|
IMAGES += factory.bin tftp.bin
|
|
|
|
IMAGE/default := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs | check-size $$$$(IMAGE_SIZE)
|
2018-10-07 11:37:42 +00:00
|
|
|
IMAGE/factory.bin := $$(IMAGE/default) | buffalo-enc WZR-HP-G450H 1.99 | buffalo-tag WZR-HP-G450H 3
|
2018-09-11 11:13:17 +00:00
|
|
|
IMAGE/tftp.bin := $$(IMAGE/default) | buffalo-tftp-header
|
2018-08-02 07:14:10 +00:00
|
|
|
SUPPORTED_DEVICES += wzr-hp-g450h
|
|
|
|
endef
|
|
|
|
TARGET_DEVICES += buffalo_wzr-hp-g450h
|
|
|
|
|
ath79: add support for COMFAST CF-E110N
This patch adds support for the COMFAST CF-E110N, an outdoor wireless
CPE with two Ethernet ports and a 802.11bgn radio.
Specifications:
- 650/400/216 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, both with PoE-in support
- 64 MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz, up to 26 dBm
- 11 dBi built-in antenna
- POWER/LAN/WAN/WLAN green LEDs
- 4x RSSI LEDs (2x red, 2x green)
- UART (115200 8N1) and GPIO (J9) headers on PCB
Flashing instructions:
The original firmware is based on OpenWrt so a sysupgrade image can be
installed via the stock web GUI. Settings from the original firmware
will be saved and restored on the new want, so a factory reset will be
needed: once the new firmware is flashed, perform the factory reset by
pushing the reset button several times during the boot process, while the
WAN LED flashes, until it starts flashing quicker.
The U-boot bootloader contains a recovery HTTP server to upload the
firmware. Push the reset button while powering the device on and keep it
pressed for >10 seconds. The recovery page will be at http://192.168.1.1
Notes:
The device is advertised, sold and labeled as "CF-E110N", but the
bootloader and the stock firmware identify it as "v2".
Acknowledgments:
Petr Štetiar <ynezz@true.cz>
Sebastian Kemper <sebastian_ml@gmx.net>
Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
[drop unused labels from devicetree source file]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-10 14:44:56 +00:00
|
|
|
define Device/comfast_cf-e110n-v2
|
|
|
|
ATH_SOC := qca9533
|
|
|
|
DEVICE_TITLE := COMFAST CF-E110N v2
|
|
|
|
DEVICE_PACKAGES := rssileds kmod-leds-gpio -swconfig -uboot-envtools
|
|
|
|
IMAGE_SIZE := 16192k
|
|
|
|
endef
|
|
|
|
TARGET_DEVICES += comfast_cf-e110n-v2
|
|
|
|
|
2018-12-27 01:32:38 +00:00
|
|
|
define Device/devolo_dvl1200e
|
|
|
|
ATH_SOC := qca9558
|
|
|
|
DEVICE_TITLE := devolo WiFi pro 1200e
|
|
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
|
|
IMAGE_SIZE := 15936k
|
|
|
|
endef
|
|
|
|
TARGET_DEVICES += devolo_dvl1200e
|
|
|
|
|
2019-01-01 18:17:23 +00:00
|
|
|
define Device/devolo_dvl1200i
|
|
|
|
ATH_SOC := qca9558
|
|
|
|
DEVICE_TITLE := devolo WiFi pro 1200i
|
|
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
|
|
IMAGE_SIZE := 15936k
|
|
|
|
endef
|
|
|
|
TARGET_DEVICES += devolo_dvl1200i
|
|
|
|
|
2018-12-27 01:32:39 +00:00
|
|
|
define Device/devolo_dvl1750c
|
|
|
|
ATH_SOC := qca9558
|
|
|
|
DEVICE_TITLE := devolo WiFi pro 1750c
|
|
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
|
|
IMAGE_SIZE := 15936k
|
|
|
|
endef
|
|
|
|
TARGET_DEVICES += devolo_dvl1750c
|
|
|
|
|
2019-01-20 16:46:42 +00:00
|
|
|
define Device/devolo_dvl1750e
|
|
|
|
ATH_SOC := qca9558
|
|
|
|
DEVICE_TITLE := devolo WiFi pro 1750e
|
|
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
|
|
IMAGE_SIZE := 15936k
|
|
|
|
endef
|
|
|
|
TARGET_DEVICES += devolo_dvl1750e
|
|
|
|
|
2019-01-01 18:17:22 +00:00
|
|
|
define Device/devolo_dvl1750i
|
|
|
|
ATH_SOC := qca9558
|
|
|
|
DEVICE_TITLE := devolo WiFi pro 1750i
|
|
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
|
|
IMAGE_SIZE := 15936k
|
|
|
|
endef
|
|
|
|
TARGET_DEVICES += devolo_dvl1750i
|
|
|
|
|
2018-08-09 17:49:29 +00:00
|
|
|
define Device/dlink_dir-825-b1
|
|
|
|
ATH_SOC := ar7161
|
|
|
|
DEVICE_TITLE := D-LINK DIR-825 B1
|
|
|
|
IMAGE_SIZE := 6208k
|
|
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata | check-size $$$$(IMAGE_SIZE)
|
|
|
|
DEVICE_PACKAGES := kmod-usb-core kmod-usb-ohci kmod-usb2 kmod-usb-ledtrig-usbport kmod-leds-reset kmod-owl-loader
|
|
|
|
SUPPORTED_DEVICES += dir-825-b1
|
|
|
|
endef
|
|
|
|
TARGET_DEVICES += dlink_dir-825-b1
|
|
|
|
|
2018-12-01 18:41:34 +00:00
|
|
|
define Device/dlink_dir-825-c1
|
|
|
|
ATH_SOC := ar9344
|
|
|
|
DEVICE_TITLE := D-LINK DIR-825 C1
|
|
|
|
DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-usb-ledtrig-usbport kmod-leds-reset kmod-owl-loader
|
|
|
|
SUPPORTED_DEVICES += dir-825-c1
|
|
|
|
IMAGE_SIZE := 15936k
|
|
|
|
IMAGES := factory.bin sysupgrade.bin
|
|
|
|
IMAGE/default := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs
|
2018-12-17 20:56:56 +00:00
|
|
|
IMAGE/factory.bin := $$(IMAGE/default) | pad-offset $$$$(IMAGE_SIZE) 26 | \
|
|
|
|
append-string 00DB120AR9344-RT-101214-00 | check-size $$$$(IMAGE_SIZE)
|
2018-12-01 18:41:34 +00:00
|
|
|
IMAGE/sysupgrade.bin := $$(IMAGE/default) | append-metadata | check-size $$$$(IMAGE_SIZE)
|
|
|
|
endef
|
|
|
|
TARGET_DEVICES += dlink_dir-825-c1
|
|
|
|
|
|
|
|
define Device/dlink_dir-835-a1
|
|
|
|
ATH_SOC := ar9344
|
|
|
|
DEVICE_TITLE := D-LINK DIR-835 A1
|
|
|
|
DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-leds-reset kmod-owl-loader
|
|
|
|
SUPPORTED_DEVICES += dir-835-a1
|
|
|
|
IMAGE_SIZE := 15936k
|
|
|
|
IMAGES := factory.bin sysupgrade.bin
|
|
|
|
IMAGE/default := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | pad-rootfs
|
2018-12-17 20:56:56 +00:00
|
|
|
IMAGE/factory.bin := $$(IMAGE/default) | pad-offset $$$$(IMAGE_SIZE) 26 | \
|
|
|
|
append-string 00DB120AR9344-RT-101214-00 | check-size $$$$(IMAGE_SIZE)
|
2018-12-01 18:41:34 +00:00
|
|
|
IMAGE/sysupgrade.bin := $$(IMAGE/default) | append-metadata | check-size $$$$(IMAGE_SIZE)
|
|
|
|
endef
|
|
|
|
TARGET_DEVICES += dlink_dir-835-a1
|
|
|
|
|
2018-12-29 09:22:32 +00:00
|
|
|
define Device/dlink_dir-859-a1
|
|
|
|
$(Device/seama)
|
|
|
|
ATH_SOC := qca9563
|
|
|
|
DEVICE_TITLE := D-LINK DIR-859 A1
|
|
|
|
IMAGE_SIZE := 15872k
|
|
|
|
DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
|
|
SEAMA_SIGNATURE := wrgac37_dlink.2013gui_dir859
|
|
|
|
SUPPORTED_DEVICES += dir-859-a1
|
|
|
|
endef
|
|
|
|
TARGET_DEVICES += dlink_dir-859-a1
|
|
|
|
|
2018-12-29 15:55:35 +00:00
|
|
|
define Device/elecom_wrc-1750ghbk2-i
|
|
|
|
ATH_SOC := qca9563
|
|
|
|
DEVICE_TITLE := ELECOM WRC-1750GHBK2-I/C
|
|
|
|
IMAGE_SIZE := 15808k
|
|
|
|
KERNEL_INITRAMFS := $$(KERNEL) | pad-to 2 | \
|
2018-12-31 15:41:07 +00:00
|
|
|
add-elecom-factory-initramfs RN68 WRC-1750GHBK2
|
2018-12-29 15:55:35 +00:00
|
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
|
|
endef
|
|
|
|
TARGET_DEVICES += elecom_wrc-1750ghbk2-i
|
|
|
|
|
2018-09-10 07:30:28 +00:00
|
|
|
define Device/elecom_wrc-300ghbk2-i
|
|
|
|
ATH_SOC := qca9563
|
|
|
|
DEVICE_TITLE := ELECOM WRC-300GHBK2-I
|
|
|
|
IMAGE_SIZE := 7616k
|
|
|
|
KERNEL_INITRAMFS := $$(KERNEL) | pad-to 2 | \
|
2018-12-31 15:41:07 +00:00
|
|
|
add-elecom-factory-initramfs RN51 WRC-300GHBK2-I
|
2018-09-10 07:30:28 +00:00
|
|
|
endef
|
|
|
|
TARGET_DEVICES += elecom_wrc-300ghbk2-i
|
|
|
|
|
2018-05-08 05:22:38 +00:00
|
|
|
define Device/embeddedwireless_dorin
|
2018-05-06 08:20:11 +00:00
|
|
|
ATH_SOC := ar9331
|
|
|
|
DEVICE_TITLE := Embedded Wireless Dorin
|
|
|
|
DEVICE_PACKAGES := kmod-usb-chipidea2
|
2018-05-07 19:09:44 +00:00
|
|
|
IMAGE_SIZE := 16000k
|
2018-05-06 08:20:11 +00:00
|
|
|
endef
|
2018-05-08 05:22:38 +00:00
|
|
|
TARGET_DEVICES += embeddedwireless_dorin
|
2018-05-06 08:20:11 +00:00
|
|
|
|
2018-12-18 08:35:30 +00:00
|
|
|
define Device/engenius_ews511ap
|
|
|
|
ATH_SOC := qca9531
|
|
|
|
DEVICE_TITLE := EnGenius EWS511AP
|
|
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9887-ct
|
|
|
|
IMAGE_SIZE := 16000k
|
|
|
|
endef
|
|
|
|
TARGET_DEVICES += engenius_ews511ap
|
|
|
|
|
2018-08-02 07:14:10 +00:00
|
|
|
define Device/etactica_eg200
|
2018-05-07 16:08:00 +00:00
|
|
|
ATH_SOC := ar9331
|
|
|
|
DEVICE_TITLE := eTactica EG200
|
|
|
|
DEVICE_PACKAGES := kmod-usb-chipidea2 kmod-ledtrig-oneshot \
|
|
|
|
kmod-usb-serial kmod-usb-serial-ftdi kmod-usb-storage kmod-fs-ext4
|
2018-08-02 07:14:10 +00:00
|
|
|
SUPPORTED_DEVICES += rme-eg200
|
2018-05-07 16:08:00 +00:00
|
|
|
endef
|
2018-08-02 07:14:10 +00:00
|
|
|
TARGET_DEVICES += etactica_eg200
|
2018-05-07 16:08:00 +00:00
|
|
|
|
2018-12-30 20:37:50 +00:00
|
|
|
define Device/glinet_gl-ar150
|
2018-05-06 08:20:11 +00:00
|
|
|
ATH_SOC := ar9330
|
|
|
|
DEVICE_TITLE := GL.iNet GL-AR150
|
|
|
|
DEVICE_PACKAGES := kmod-usb-chipidea2
|
|
|
|
IMAGE_SIZE := 16000k
|
2018-05-07 20:41:04 +00:00
|
|
|
SUPPORTED_DEVICES += gl-ar150
|
2018-05-06 08:20:11 +00:00
|
|
|
endef
|
2018-12-30 20:37:50 +00:00
|
|
|
TARGET_DEVICES += glinet_gl-ar150
|
2018-05-06 08:20:11 +00:00
|
|
|
|
2018-12-31 12:45:29 +00:00
|
|
|
define Device/glinet_gl-ar300m-nor
|
2018-10-29 03:56:46 +00:00
|
|
|
ATH_SOC := qca9531
|
2018-05-27 05:37:22 +00:00
|
|
|
DEVICE_TITLE := GL.iNet GL-AR300M
|
|
|
|
DEVICE_PACKAGES := kmod-usb-core kmod-usb2
|
|
|
|
IMAGE_SIZE := 16000k
|
|
|
|
SUPPORTED_DEVICES += gl-ar300m
|
|
|
|
endef
|
2018-12-31 12:45:29 +00:00
|
|
|
TARGET_DEVICES += glinet_gl-ar300m-nor
|
2018-05-27 05:37:22 +00:00
|
|
|
|
2019-01-01 12:03:20 +00:00
|
|
|
define Device/glinet_gl-ar750s
|
2018-12-30 16:36:22 +00:00
|
|
|
ATH_SOC := qca9563
|
|
|
|
DEVICE_TITLE := GL.iNet GL-AR750S
|
|
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
|
|
IMAGE_SIZE := 16000k
|
|
|
|
SUPPORTED_DEVICES += gl-ar750s
|
|
|
|
endef
|
2019-01-01 12:03:20 +00:00
|
|
|
TARGET_DEVICES += glinet_gl-ar750s
|
2018-12-30 16:36:22 +00:00
|
|
|
|
2018-11-26 14:39:25 +00:00
|
|
|
define Device/glinet_gl-x750
|
2018-10-29 03:56:46 +00:00
|
|
|
ATH_SOC := qca9531
|
2018-11-26 14:39:25 +00:00
|
|
|
DEVICE_TITLE := GL.iNet GL-X750
|
2018-12-17 00:58:49 +00:00
|
|
|
DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca9887-ct
|
2018-11-05 02:03:05 +00:00
|
|
|
IMAGE_SIZE := 16000k
|
|
|
|
endef
|
2018-11-26 14:39:25 +00:00
|
|
|
TARGET_DEVICES += glinet_gl-x750
|
2018-11-05 02:03:05 +00:00
|
|
|
|
2018-08-20 07:32:42 +00:00
|
|
|
define Device/iodata_etg3-r
|
|
|
|
ATH_SOC := ar9342
|
|
|
|
DEVICE_TITLE := I-O DATA ETG3-R
|
|
|
|
IMAGE_SIZE := 7680k
|
|
|
|
endef
|
|
|
|
TARGET_DEVICES += iodata_etg3-r
|
|
|
|
|
2018-08-16 08:08:28 +00:00
|
|
|
define Device/iodata_wn-ac1167dgr
|
|
|
|
ATH_SOC := qca9557
|
|
|
|
DEVICE_TITLE := I-O DATA WN-AC1167DGR
|
|
|
|
IMAGE_SIZE := 14656k
|
|
|
|
IMAGES += factory.bin
|
|
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
|
|
|
append-rootfs | pad-rootfs | check-size $$$$(IMAGE_SIZE) | \
|
|
|
|
senao-header -r 0x30a -p 0x61 -t 2
|
2018-09-05 12:51:44 +00:00
|
|
|
DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
2018-08-16 08:08:28 +00:00
|
|
|
endef
|
|
|
|
TARGET_DEVICES += iodata_wn-ac1167dgr
|
|
|
|
|
2019-02-05 08:23:58 +00:00
|
|
|
define Device/iodata_wn-ac1600dgr
|
|
|
|
ATH_SOC := qca9557
|
|
|
|
DEVICE_TITLE := I-O DATA WN-AC1600DGR
|
|
|
|
IMAGE_SIZE := 14656k
|
|
|
|
IMAGES += factory.bin
|
|
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
|
|
|
append-rootfs | pad-rootfs | check-size $$$$(IMAGE_SIZE) | \
|
|
|
|
senao-header -r 0x30a -p 0x60 -t 2 -v 200
|
|
|
|
DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
|
|
|
endef
|
|
|
|
TARGET_DEVICES += iodata_wn-ac1600dgr
|
|
|
|
|
2018-08-10 00:07:53 +00:00
|
|
|
define Device/iodata_wn-ac1600dgr2
|
|
|
|
ATH_SOC := qca9557
|
|
|
|
DEVICE_TITLE := I-O DATA WN-AC1600DGR2
|
|
|
|
IMAGE_SIZE := 14656k
|
|
|
|
IMAGES += factory.bin
|
|
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
|
|
|
append-rootfs | pad-rootfs | check-size $$$$(IMAGE_SIZE) | \
|
|
|
|
senao-header -r 0x30a -p 0x60 -t 2 -v 200
|
2018-09-05 12:51:44 +00:00
|
|
|
DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
2018-08-10 00:07:53 +00:00
|
|
|
endef
|
|
|
|
TARGET_DEVICES += iodata_wn-ac1600dgr2
|
|
|
|
|
2018-11-30 10:04:23 +00:00
|
|
|
define Device/iodata_wn-ag300dgr
|
|
|
|
ATH_SOC := ar1022
|
|
|
|
DEVICE_TITLE := I-O DATA WN-AG300DGR
|
|
|
|
IMAGE_SIZE := 15424k
|
|
|
|
IMAGES += factory.bin
|
|
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
|
|
|
append-rootfs | pad-rootfs | check-size $$$$(IMAGE_SIZE) | \
|
|
|
|
senao-header -r 0x30a -p 0x47 -t 2
|
|
|
|
DEVICE_PACKAGES := kmod-usb-core kmod-usb2
|
|
|
|
endef
|
|
|
|
TARGET_DEVICES += iodata_wn-ag300dgr
|
|
|
|
|
2018-12-08 06:18:17 +00:00
|
|
|
define Device/nec_wg800hp
|
|
|
|
ATH_SOC := qca9563
|
|
|
|
DEVICE_TITLE := NEC Aterm WG800HP
|
|
|
|
IMAGE_SIZE := 7104k
|
|
|
|
IMAGES += factory.bin
|
|
|
|
IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
|
|
|
|
append-rootfs | pad-rootfs | check-size $$$$(IMAGE_SIZE) | \
|
|
|
|
xor-image -p 6A57190601121E4C004C1E1201061957 -x | \
|
|
|
|
nec-fw LASER_ATERM
|
|
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9887-ct-htt
|
|
|
|
endef
|
|
|
|
TARGET_DEVICES += nec_wg800hp
|
|
|
|
|
2018-08-08 20:13:44 +00:00
|
|
|
define Device/ocedo_koala
|
|
|
|
ATH_SOC := qca9558
|
|
|
|
DEVICE_TITLE := OCEDO Koala
|
2018-09-05 12:51:44 +00:00
|
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
|
2018-08-08 20:13:44 +00:00
|
|
|
SUPPORTED_DEVICES += koala
|
|
|
|
IMAGE_SIZE := 7424k
|
|
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata | check-size $$$$(IMAGE_SIZE)
|
|
|
|
endef
|
|
|
|
TARGET_DEVICES += ocedo_koala
|
|
|
|
|
2018-07-06 16:23:31 +00:00
|
|
|
define Device/ocedo_raccoon
|
|
|
|
ATH_SOC := ar9344
|
|
|
|
DEVICE_TITLE := OCEDO Raccoon
|
|
|
|
IMAGE_SIZE := 7424k
|
|
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata | check-size $$$$(IMAGE_SIZE)
|
|
|
|
endef
|
|
|
|
TARGET_DEVICES += ocedo_raccoon
|
|
|
|
|
2018-05-08 05:22:38 +00:00
|
|
|
define Device/openmesh_om5p-ac-v2
|
2018-05-06 08:20:11 +00:00
|
|
|
ATH_SOC := qca9558
|
2018-05-08 05:22:38 +00:00
|
|
|
DEVICE_TITLE := OpenMesh OM5P-AC v2
|
2018-09-05 12:51:44 +00:00
|
|
|
DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct om-watchdog
|
2018-05-07 19:09:44 +00:00
|
|
|
IMAGE_SIZE := 7808k
|
2018-05-07 20:41:04 +00:00
|
|
|
SUPPORTED_DEVICES += om5p-acv2
|
2018-05-06 08:20:11 +00:00
|
|
|
endef
|
2018-05-08 05:22:38 +00:00
|
|
|
TARGET_DEVICES += openmesh_om5p-ac-v2
|
2018-05-06 08:20:11 +00:00
|
|
|
|
2018-07-28 12:52:39 +00:00
|
|
|
define Device/pcs_cap324
|
|
|
|
ATH_SOC := ar9344
|
|
|
|
DEVICE_TITLE := PowerCloud Systems CAP324
|
|
|
|
IMAGE_SIZE := 16000k
|
|
|
|
SUPPORTED_DEVICES += cap324
|
|
|
|
endef
|
|
|
|
TARGET_DEVICES += pcs_cap324
|
|
|
|
|
2018-07-28 12:57:22 +00:00
|
|
|
define Device/pcs_cr3000
|
|
|
|
ATH_SOC := ar9341
|
|
|
|
DEVICE_TITLE := PowerCloud Systems CR3000
|
|
|
|
IMAGE_SIZE := 7808k
|
|
|
|
SUPPORTED_DEVICES += cr3000
|
|
|
|
endef
|
|
|
|
TARGET_DEVICES += pcs_cr3000
|
|
|
|
|
2018-07-20 20:52:46 +00:00
|
|
|
define Device/pcs_cr5000
|
|
|
|
ATH_SOC := ar9344
|
|
|
|
DEVICE_TITLE := PowerCloud Systems CR5000
|
2018-08-16 07:53:26 +00:00
|
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-usb-core
|
2018-07-20 20:52:46 +00:00
|
|
|
IMAGE_SIZE := 7808k
|
|
|
|
SUPPORTED_DEVICES += cr5000
|
|
|
|
endef
|
|
|
|
TARGET_DEVICES += pcs_cr5000
|
|
|
|
|
2018-08-11 11:47:21 +00:00
|
|
|
define Device/netgear_wndr3x00
|
2018-05-06 08:20:11 +00:00
|
|
|
ATH_SOC := ar7161
|
2018-05-07 19:09:44 +00:00
|
|
|
KERNEL := kernel-bin | append-dtb | lzma -d20 | netgear-uImage lzma
|
2018-12-06 11:07:56 +00:00
|
|
|
IMAGES += factory.img
|
2018-05-07 19:09:44 +00:00
|
|
|
IMAGE/default := append-kernel | pad-to $$$$(BLOCKSIZE) | netgear-squashfs | append-rootfs | pad-rootfs
|
2018-05-07 20:41:04 +00:00
|
|
|
IMAGE/sysupgrade.bin := $$(IMAGE/default) | append-metadata | check-size $$$$(IMAGE_SIZE)
|
2018-05-07 19:09:44 +00:00
|
|
|
IMAGE/factory.img := $$(IMAGE/default) | netgear-dni | check-size $$$$(IMAGE_SIZE)
|
2018-08-13 20:10:47 +00:00
|
|
|
DEVICE_PACKAGES := kmod-usb-core kmod-usb-ohci kmod-usb2 kmod-usb-ledtrig-usbport kmod-leds-reset kmod-owl-loader
|
2018-08-11 11:47:21 +00:00
|
|
|
endef
|
|
|
|
|
2018-08-11 22:18:53 +00:00
|
|
|
define Device/netgear_wndr3700
|
|
|
|
$(Device/netgear_wndr3x00)
|
|
|
|
DEVICE_TITLE := NETGEAR WNDR3700
|
|
|
|
NETGEAR_KERNEL_MAGIC := 0x33373030
|
|
|
|
NETGEAR_BOARD_ID := WNDR3700
|
|
|
|
IMAGE_SIZE := 7680k
|
|
|
|
IMAGES += factory-NA.img
|
|
|
|
IMAGE/factory-NA.img := $$(IMAGE/default) | netgear-dni NA | check-size $$$$(IMAGE_SIZE)
|
|
|
|
SUPPORTED_DEVICES += wndr3700
|
|
|
|
endef
|
|
|
|
TARGET_DEVICES += netgear_wndr3700
|
|
|
|
|
|
|
|
define Device/netgear_wndr3700v2
|
|
|
|
$(Device/netgear_wndr3x00)
|
|
|
|
DEVICE_TITLE := NETGEAR WNDR3700v2
|
|
|
|
NETGEAR_KERNEL_MAGIC := 0x33373031
|
|
|
|
NETGEAR_BOARD_ID := WNDR3700v2
|
|
|
|
NETGEAR_HW_ID := 29763654+16+64
|
|
|
|
IMAGE_SIZE := 15872k
|
|
|
|
SUPPORTED_DEVICES += wndr3700v2
|
|
|
|
endef
|
|
|
|
TARGET_DEVICES += netgear_wndr3700v2
|
|
|
|
|
2018-08-12 14:32:01 +00:00
|
|
|
define Device/pisen_wmm003n
|
|
|
|
$(Device/tplink-8mlzma)
|
|
|
|
ATH_SOC := ar9331
|
|
|
|
DEVICE_TITLE := Pisen WMM003N (Cloud Easy Power)
|
|
|
|
DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-usb-chipidea2
|
|
|
|
TPLINK_HWID := 0x07030101
|
|
|
|
endef
|
|
|
|
TARGET_DEVICES += pisen_wmm003n
|
|
|
|
|
2018-08-11 11:47:21 +00:00
|
|
|
define Device/netgear_wndr3800
|
|
|
|
$(Device/netgear_wndr3x00)
|
|
|
|
DEVICE_TITLE := NETGEAR WNDR3800
|
|
|
|
NETGEAR_KERNEL_MAGIC := 0x33373031
|
|
|
|
NETGEAR_BOARD_ID := WNDR3800
|
|
|
|
NETGEAR_HW_ID := 29763654+16+128
|
|
|
|
IMAGE_SIZE := 15872k
|
2018-05-07 20:41:04 +00:00
|
|
|
SUPPORTED_DEVICES += wndr3800
|
2018-05-06 08:20:11 +00:00
|
|
|
endef
|
|
|
|
TARGET_DEVICES += netgear_wndr3800
|
|
|
|
|
2018-08-02 07:14:10 +00:00
|
|
|
define Device/phicomm_k2t
|
2018-06-13 13:14:49 +00:00
|
|
|
ATH_SOC := qca9563
|
|
|
|
DEVICE_TITLE := Phicomm K2T
|
|
|
|
IMAGE_SIZE := 15744k
|
2018-12-06 11:07:56 +00:00
|
|
|
IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata | check-size $$$$(IMAGE_SIZE)
|
2018-09-05 12:51:44 +00:00
|
|
|
DEVICE_PACKAGES := kmod-leds-reset kmod-ath10k-ct ath10k-firmware-qca9888-ct
|
2018-06-13 13:14:49 +00:00
|
|
|
endef
|
2018-08-02 07:14:10 +00:00
|
|
|
TARGET_DEVICES += phicomm_k2t
|
2018-09-04 21:27:02 +00:00
|
|
|
|
ath79: add support for ROSINSON WR818 board
This commit adds support for the ROSINSON WR818 WiFi-Router
SoC: Qualcomm Atheros QCA9563,
FLASH: Winbond W25Q128FV 16MBytes,
WiFi: QCA9563 b/g/n 3x3 450Mbit/s,
USB: 1x USB 2.0 Type A, 1x USB2.0 Type C,
IN: WPS/Reset button GPIO1,
OUT: Power LED red, Internet LED red, WLAN LED red,
LAN1 LED red, LAN2 LED red, System LED red,
UART: RX-GPIO18, TX-GPIO22,
Tested and working:
- Ethernet (LAN + WAN)
- WiFi
- OpenWRT sysupgrade
- Button
- LEDs
Installation of OpenWRT from vendor firmware:
- Connect to the Web-interface at http://192.168.1.1
- Go to "Administration" -> "Firmware Upgrade"
- Upload the OpenWrt sysupgrade image
Signed-off-by: Rosy Song <rosysong@rosinson.com>
2018-10-07 04:04:54 +00:00
|
|
|
define Device/rosinson_wr818
|
|
|
|
ATH_SOC := qca9563
|
|
|
|
DEVICE_TITLE := ROSINSON WR818
|
|
|
|
IMAGE_SIZE := 15872k
|
|
|
|
DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-usb-ledtrig-usbport
|
|
|
|
endef
|
|
|
|
TARGET_DEVICES += rosinson_wr818
|
|
|
|
|
2018-09-04 21:27:02 +00:00
|
|
|
define Device/wd_mynet-wifi-rangeextender
|
|
|
|
ATH_SOC := ar9344
|
|
|
|
DEVICE_TITLE := Western Digital My Net Wi-Fi Range Extender
|
|
|
|
DEVICE_PACKAGES := rssileds nvram -swconfig
|
|
|
|
IMAGE_SIZE := 7808k
|
|
|
|
ADDPATTERN_ID := mynet-rext
|
|
|
|
ADDPATTERN_VERSION := 1.00.01
|
|
|
|
IMAGE/sysupgrade.bin := append-rootfs | pad-rootfs | cybertan-trx | \
|
|
|
|
addpattern | append-metadata
|
|
|
|
SUPPORTED_DEVICES += mynet-rext
|
|
|
|
endef
|
|
|
|
TARGET_DEVICES += wd_mynet-wifi-rangeextender
|
2018-10-30 16:05:43 +00:00
|
|
|
|
|
|
|
define Device/winchannel_wb2000
|
|
|
|
ATH_SOC := ar9344
|
|
|
|
DEVICE_TITLE := Winchannel WB2000
|
|
|
|
IMAGE_SIZE := 15872k
|
|
|
|
DEVICE_PACKAGES := kmod-i2c-core kmod-i2c-gpio kmod-rtc-ds1307 kmod-usb2 kmod-usb-ledtrig-usbport
|
|
|
|
endef
|
|
|
|
TARGET_DEVICES += winchannel_wb2000
|
2019-02-01 19:48:41 +00:00
|
|
|
|
|
|
|
define Device/xiaomi_mi-router-4q
|
|
|
|
ATH_SOC := qca9561
|
|
|
|
DEVICE_TITLE := Xiaomi Mi Router 4Q
|
|
|
|
IMAGE_SIZE := 14336k
|
|
|
|
endef
|
|
|
|
TARGET_DEVICES += xiaomi_mi-router-4q
|