2016-04-01 07:11:48 +00:00
|
|
|
#
|
2017-08-26 01:49:45 +00:00
|
|
|
# MT76x8 Profiles
|
2016-04-01 07:11:48 +00:00
|
|
|
#
|
|
|
|
|
|
2017-12-17 09:44:41 +00:00
|
|
|
define Device/tplink
|
|
|
|
|
TPLINK_FLASHLAYOUT :=
|
|
|
|
|
TPLINK_HWID :=
|
|
|
|
|
TPLINK_HWREV :=
|
|
|
|
|
TPLINK_HWREVADD :=
|
|
|
|
|
TPLINK_HVERSION :=
|
|
|
|
|
KERNEL := $(KERNEL_DTB)
|
|
|
|
|
KERNEL_INITRAMFS := $(KERNEL_DTB) | tplink-v2-header -e
|
|
|
|
|
IMAGES += tftp-recovery.bin
|
|
|
|
|
IMAGE/factory.bin := tplink-v2-image -e
|
|
|
|
|
IMAGE/tftp-recovery.bin := pad-extra 128k | $$(IMAGE/factory.bin)
|
|
|
|
|
IMAGE/sysupgrade.bin := tplink-v2-image -s -e | append-metadata | \
|
|
|
|
|
check-size $$$$(IMAGE_SIZE)
|
|
|
|
|
endef
|
2017-10-03 10:46:09 +00:00
|
|
|
DEVICE_VARS += TPLINK_FLASHLAYOUT TPLINK_HWID TPLINK_HWREV TPLINK_HWREVADD TPLINK_HVERSION
|
ramips: add support for TP-Link TL-WR840N v4 and TL-WR841N v13
TP-Link TL-WR840N v4 and TL-WR841N v13 are simple N300 routers with
5-port FE switch and non-detachable antennas. Both are very similar
and are based on MediaTek MT7628NN (aka MT7628N) WiSoC.
The difference between these two models is in number of available
LEDs, buttons and power input switch.
This work is partially based on GitHub PR#974.
Specification:
- MT7628N/N (580 MHz)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- TL-WR840N v4: 5x LED (GPIO-controlled), 1x button
- TL-WR841N v13: 8x LED (GPIO-controlled*), 2x button, power input
switch
* WAN LED in TL-WR841N v13 is a dual-color, dual-leads type which isn't
(fully) supported by gpio-leds driver. This type of LED requires both
GPIOs state change at the same time to select color or turn it off.
For now, we support/use only the green part of the LED.
Factory image notes:
These devices use version 3 of TP-Link header, fortunately without RSA
signature (at least in case of devices sold in Europe). The difference
lays in the requirement for a non-zero value in "Additional Hardware
Version" field. Ideally, it should match the value stored in vendor
firmware header on device ("0x4"/"0x13" for these devices) but it seems
that anything other than "0" is correct.
We are able to prepare factory firwmare file which is accepted and
(almost) correctly flashed from the vendor GUI. As it turned out, it
accepts files without U-Boot image with second header at the beginning
but due to some kind of bug in upgrade routine, flashed image gets
corrupted before it's written to flash.
Tests showed that the GUI upgrade routine copies value of "Additional
Hardware Version" from existing firmware into offset "0x2023c" in
provided file, _before_ storing it in flash. In case of vendor firmware
upgrade files (which all include U-Boot image and two headers), this
offset points to the matching field in kernel+rootfs firmware part
header. Unfortunately, in case of LEDE factory image file which contains
only one header, it points to the offset "0x2023c" in kernel image. This
leads to a corrupted kernel and ends up with a "soft-bricked" device.
The good news is that U-Boot in these devices contains well known tftp
recovery mode, which can be triggered with "reset" button. What's more,
in comparison to some of older MediaTek based TP-Link devices, this
recovery mode doesn't write whole file at offset "0x0" in flash, without
verifying provided file in advance. In case of recovery mode in these
devices, first "0x20000" bytes are always skipped and "0x7a0000" bytes
from rest of the file are stored in flash at offset "0x20000".
Flash instruction:
Until (if at all) TP-Link fixes described problem, the only way to flash
LEDE image in these devices is to use tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "lede-ramips-mt7628-tl-wr84...-squashfs-tftp-recovery.bin"
to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed for around 6-7 seconds, until
device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.
To access U-Boot CLI, keep pressed "4" key during boot.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-21 12:16:15 +00:00
|
|
|
|
2017-12-17 09:44:41 +00:00
|
|
|
|
2018-01-26 15:21:34 +00:00
|
|
|
define Device/alfa-network_awusfree1
|
|
|
|
|
DTS := AWUSFREE1
|
|
|
|
|
IMAGE_SIZE := $(ralink_default_fw_size_8M)
|
|
|
|
|
DEVICE_TITLE := ALFA Network AWUSFREE1
|
|
|
|
|
DEVICE_PACKAGES := uboot-envtools
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += alfa-network_awusfree1
|
|
|
|
|
|
ramips: add CUDY WR1000 support
Cudy WR1200 is an AC1200 AP with 3-port FE and 2 non-detachable antennas
Specifications:
MT7628 (580 MHz)
64 MB of RAM (DDR2)
8 MB of FLASH
2T2R 2.4 GHz (MT7628)
2T2R 5 GHz (MT7612E)
3x 10/100 Mbps Ethernet (2 LAN + 1 WAN)
2x external, non-detachable antennas (5dbi)
UART header on PCB (57600 8n1)
7x LED, 2x button
Known issues:
The Power LED is always ON, probably because it is connected
directly to power.
Flash instructions
------------------
Load the ...-factory.bin image via the stock web interface.
Openwrt upgrade instructions
----------------------------
Use the ...-sysupgrade.bin image for future upgrades.
Revert to stock FW
------------------
Warning! This tutorial will work only with the following OEM FW:
WR1000_EU_92.122.2.4987.201806261618.bin
WR1000_US_92.122.2.4987.201806261609.bin
If in the future these firmwares will not be available anymore,
you have to find the new XOR key.
1) Download the original FW from the Cudy website.
(For example WR1000_EU_92.122.2.4987.201806261618.bin)
2) Remove the header.
dd if="WR1000_EU_92.122.2.4987.201806261618.bin" of="WR1000_EU_92.122.2.4987.201806261618.bin.mod" skip=8 bs=64
3) XOR the new file with the region key.
FOR EU: 7B76741E67594351555042461D625F4545514B1B03050208000603020803000D
FOR US: 7B76741E675943555D5442461D625F454555431F03050208000603060007010C
You can use OpenWrt's tools/firmware-utils/src/xorimage.c tool for this:
xorimage -i WR1000..bin.mod -o stock-firmware.bin -x -p 7B767..
Or, you can use this tool (CHANGE THE XOR KEY ACCORDINGLY!):
https://gchq.github.io/CyberChef/#recipe=XOR(%7B'option':'Hex','string':''%7D,'',false)
4) Check the resulting decrypted image.
Check if bytes from 0x20 to 0x3f are:
4C 69 6E 75 78 20 4B 65 72 6E 65 6C 20 49 6D 61 67 65 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Alternatively, you can use u-boot's tool dumpimage tool to check
if the decryption was successful. It should look like:
# dumpimage -l stock-firmware.bin
Image Name: Linux Kernel Image
Created: Tue Jun 26 10:24:54 2018
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 4406635 Bytes = 4303.35 KiB = 4.20 MiB
Load Address: 80000000
Entry Point: 8000c150
5) Flash it via forced firmware upgrade and don't "Keep Settings"
CLI: sysupgrade -F -n stock-firmware.bin
LuCI: make sure to click on the "Keep settings" checkbox
to disable it. You'll need to do this !TWICE! because
on the first try, LuCI will refuse the image and reset
the "Keep settings" to enable. However a new
"Force upgrade" checkbox will appear as well.
Make sure to do this very carefully!
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[added wifi compatible, spiffed-up the returned to stock instructions]
2019-05-20 03:20:37 +00:00
|
|
|
define Device/cudy_wr1000
|
|
|
|
|
DTS := WR1000
|
|
|
|
|
IMAGE_SIZE := $(ralink_default_fw_size_8M)
|
|
|
|
|
IMAGES += factory.bin
|
|
|
|
|
IMAGE/factory.bin := \
|
|
|
|
|
$$(sysupgrade_bin) | check-size $$$$(IMAGE_SIZE) | jcg-header 92.122
|
|
|
|
|
JCG_MAXSIZE := 8060928
|
|
|
|
|
DEVICE_TITLE := Cudy WR1000
|
|
|
|
|
DEVICE_PACKAGES := kmod-mt76x2
|
|
|
|
|
SUPPORTED_DEVICES += wr1000
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += cudy_wr1000
|
|
|
|
|
|
2018-02-19 05:35:42 +00:00
|
|
|
define Device/tama_w06
|
|
|
|
|
DTS := W06
|
|
|
|
|
IMAGE_SIZE := 15040k
|
|
|
|
|
DEVICE_TITLE := Tama W06
|
|
|
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ohci
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += tama_w06
|
|
|
|
|
|
2017-08-26 01:49:45 +00:00
|
|
|
define Device/duzun-dm06
|
|
|
|
|
DTS := DUZUN-DM06
|
|
|
|
|
DEVICE_TITLE := DuZun DM06
|
2016-10-19 10:09:45 +00:00
|
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ohci kmod-usb-ledtrig-usbport
|
2016-05-11 10:21:45 +00:00
|
|
|
endef
|
2017-08-26 01:49:45 +00:00
|
|
|
TARGET_DEVICES += duzun-dm06
|
|
|
|
|
|
|
|
|
|
define Device/gl-mt300n-v2
|
|
|
|
|
DTS := GL-MT300N-V2
|
|
|
|
|
IMAGE_SIZE := 16064k
|
|
|
|
|
DEVICE_TITLE := GL-iNet GL-MT300N-V2
|
|
|
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ohci
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += gl-mt300n-v2
|
2016-04-01 07:11:48 +00:00
|
|
|
|
2019-04-12 22:05:47 +00:00
|
|
|
define Device/glinet_vixmini
|
|
|
|
|
DTS := VIXMINI
|
|
|
|
|
IMAGE_SIZE := 7872k
|
|
|
|
|
DEVICE_TITLE := GL.iNet VIXMINI
|
|
|
|
|
SUPPORTED_DEVICES += vixmini
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += glinet_vixmini
|
|
|
|
|
|
2017-02-24 23:19:15 +00:00
|
|
|
define Device/hc5661a
|
|
|
|
|
DTS := HC5661A
|
|
|
|
|
IMAGE_SIZE := $(ralink_default_fw_size_16M)
|
|
|
|
|
DEVICE_TITLE := HiWiFi HC5661A
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += hc5661a
|
|
|
|
|
|
2019-05-05 02:54:52 +00:00
|
|
|
define Device/hilink_hlk-7628n
|
|
|
|
|
DTS := HLK-7628N
|
|
|
|
|
IMAGE_SIZE := $(ralink_default_fw_size_32M)
|
|
|
|
|
DEVICE_TITLE := HILINK HLK7628N
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += hilink_hlk-7628n
|
|
|
|
|
|
2018-08-09 17:22:46 +00:00
|
|
|
define Device/hiwifi_hc5861b
|
|
|
|
|
DTS := HC5861B
|
|
|
|
|
IMAGE_SIZE := 15808k
|
|
|
|
|
DEVICE_TITLE := HiWiFi HC5861B
|
2018-11-30 10:10:29 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt76x2
|
2018-08-09 17:22:46 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += hiwifi_hc5861b
|
|
|
|
|
|
2017-08-26 01:49:45 +00:00
|
|
|
define Device/LinkIt7688
|
|
|
|
|
DTS := LINKIT7688
|
|
|
|
|
IMAGE_SIZE := $(ralink_default_fw_size_32M)
|
|
|
|
|
SUPPORTED_DEVICES := linkits7688 linkits7688d
|
|
|
|
|
DEVICE_TITLE := MediaTek LinkIt Smart 7688
|
|
|
|
|
DEVICE_PACKAGES:= kmod-usb2 kmod-usb-ohci uboot-envtools
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += LinkIt7688
|
|
|
|
|
|
|
|
|
|
define Device/mac1200r-v2
|
|
|
|
|
DTS := MAC1200RV2
|
|
|
|
|
DEVICE_TITLE := Mercury MAC1200R v2.0
|
|
|
|
|
SUPPORTED_DEVICES := mac1200rv2
|
2018-11-30 10:10:29 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt76x2
|
2017-08-26 01:49:45 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += mac1200r-v2
|
|
|
|
|
|
2016-05-11 10:21:45 +00:00
|
|
|
define Device/miwifi-nano
|
|
|
|
|
DTS := MIWIFI-NANO
|
|
|
|
|
IMAGE_SIZE := $(ralink_default_fw_size_16M)
|
|
|
|
|
DEVICE_TITLE := Xiaomi MiWiFi Nano
|
2016-10-19 10:09:45 +00:00
|
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ohci kmod-usb-ledtrig-usbport
|
2016-04-01 07:11:48 +00:00
|
|
|
endef
|
2016-05-11 10:21:45 +00:00
|
|
|
TARGET_DEVICES += miwifi-nano
|
2016-04-01 07:11:48 +00:00
|
|
|
|
2017-08-26 01:49:45 +00:00
|
|
|
define Device/mt7628
|
|
|
|
|
DTS := MT7628
|
|
|
|
|
BLOCKSIZE := 64k
|
|
|
|
|
IMAGE_SIZE := $(ralink_default_fw_size_4M)
|
|
|
|
|
DEVICE_TITLE := MediaTek MT7628 EVB
|
|
|
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ohci kmod-usb-ledtrig-usbport
|
|
|
|
|
endef
|
2018-04-23 17:36:02 +00:00
|
|
|
TARGET_DEVICES += mt7628
|
2017-08-26 01:49:45 +00:00
|
|
|
|
2018-06-12 19:17:23 +00:00
|
|
|
define Device/netgear_r6120
|
|
|
|
|
DTS := R6120
|
|
|
|
|
BLOCKSIZE := 64k
|
|
|
|
|
IMAGE_SIZE := $(ralink_default_fw_size_16M)
|
2019-01-21 00:00:49 +00:00
|
|
|
DEVICE_TITLE := Netgear R6120
|
2018-11-30 10:10:29 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt76x2 kmod-usb2 kmod-usb-ohci
|
2018-06-12 19:17:23 +00:00
|
|
|
SERCOMM_HWID := CGQ
|
|
|
|
|
SERCOMM_HWVER := A001
|
2018-11-08 11:46:37 +00:00
|
|
|
SERCOMM_SWVER := 0x0040
|
2018-06-12 19:17:23 +00:00
|
|
|
IMAGES += factory.img
|
|
|
|
|
IMAGE/default := append-kernel | pad-to $$$$(BLOCKSIZE)| append-rootfs | pad-rootfs
|
|
|
|
|
IMAGE/sysupgrade.bin := $$(IMAGE/default) | append-metadata | check-size $$$$(IMAGE_SIZE)
|
2019-05-09 16:04:06 +00:00
|
|
|
IMAGE/factory.img := pad-extra 576k | $$(IMAGE/default) | pad-to $$$$(BLOCKSIZE) | \
|
2019-01-12 19:18:52 +00:00
|
|
|
sercom-footer | pad-to 128 | zip R6120.bin | sercom-seal
|
2018-06-12 19:17:23 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += netgear_r6120
|
|
|
|
|
|
2017-08-26 01:49:45 +00:00
|
|
|
define Device/omega2
|
|
|
|
|
DTS := OMEGA2
|
|
|
|
|
IMAGE_SIZE := $(ralink_default_fw_size_16M)
|
|
|
|
|
DEVICE_TITLE := Onion Omega2
|
|
|
|
|
DEVICE_PACKAGES:= kmod-usb2 kmod-usb-ohci uboot-envtools
|
|
|
|
|
endef
|
2017-12-10 22:45:20 +00:00
|
|
|
TARGET_DEVICES += omega2
|
2017-08-26 01:49:45 +00:00
|
|
|
|
|
|
|
|
define Device/omega2p
|
|
|
|
|
DTS := OMEGA2P
|
|
|
|
|
IMAGE_SIZE := $(ralink_default_fw_size_32M)
|
|
|
|
|
DEVICE_TITLE := Onion Omega2+
|
|
|
|
|
DEVICE_PACKAGES:= kmod-usb2 kmod-usb-ohci uboot-envtools kmod-sdhci-mt7620
|
|
|
|
|
endef
|
2017-12-10 22:45:20 +00:00
|
|
|
TARGET_DEVICES += omega2p
|
2017-08-26 01:49:45 +00:00
|
|
|
|
|
|
|
|
define Device/pbr-d1
|
|
|
|
|
DTS := PBR-D1
|
|
|
|
|
IMAGE_SIZE := $(ralink_default_fw_size_16M)
|
|
|
|
|
DEVICE_TITLE := PBR-D1
|
|
|
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ohci
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += pbr-d1
|
|
|
|
|
|
2019-02-26 22:04:53 +00:00
|
|
|
define Device/rakwireless_rak633
|
|
|
|
|
DTS := RAK633
|
|
|
|
|
DEVICE_TITLE := Rakwireless RAK633
|
|
|
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ohci
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += rakwireless_rak633
|
|
|
|
|
|
2018-11-26 11:34:48 +00:00
|
|
|
define Device/skylab_skw92a
|
ramips: add support for Skylab SKW92A in EVB
Specifically, SKW92A_E16, described here:
http://www.skylabmodule.com/wp-content/uploads/SkyLab_SKW92A_V1.04_datasheet.pdf
Specification:
- MediaTek MT7628N/N (580 Mhz)
- 64 MB of RAM
- 16 MB of FLASH
- 2T2R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x u.FL
- Power by micro-USB connector at USB1 on EVB
- UART via micro-USB connector at USB3 on EVB (57600 8n1)
- 5x Ethernet LEDs
- 1x WLAN LEDs
- 1x WPS LED connected by jumper wire from I2S_CK on J20 to WPS_LED pin hole next
to daughter board on EVB
- WPS/Reset button (S2 on EVB)
- RESET button (S1 on EVB) is *not* connected to RST hole next to daughter board
Flash instruction:
>From Skylab firmware:
1. Associate with SKYLAP_AP
2. In a browser, load: http://10.10.10.254/
3. Username/password: admin/admin
4. In web admin interface: Administration / Upload Firmware, browse to
sysupgrade image, apply, flash will fail with a message:
Not a valid firmware. *** Warning: "/var/tmpFW" has corrupted data!
5. Telnet to 10.10.10.254, drops you into a root shell with no credentials
6. # cd /var
7. # mtd_write -r write tmpFW mtd4
Unlocking mtd4 ...
Writing from tmpFW to mtd4 ... [e]
8. When flash has completed, you will have booted into your firmware.
>From U-boot via TFTP and initramfs:
1. Place openwrt-ramips-mt76x8-skw92a-initramfs-kernel.bin on a TFTP server
2. Connect to serial console at USB3 on EVB
3. Connect ethernet between port 1 (not WAN) and your TFTP server (e.g.
192.168.11.20)
4. Start terminal software (e.g. screen /dev/ttyUSB0 57600) on PC
5. Apply power to EVB
6. Interrupt u-boot with keypress of "1"
7. At u-boot prompts:
Input device IP (10.10.10.123) ==:192.168.11.21
Input server IP (10.10.10.3) ==:192.168.11.20
Input Linux Kernel filename (root_uImage) ==:openwrt-ramips-mt76x8-skw92a-initramfs-kernel.bin
8. Move ethernet to port 0 (WAN) on EVB
9. At new OpenWrt console shell, fetch squashfs-sysupgrade image and flash
with sysupgrade.
>From U-boot via TFTP direct flash:
1. Place openwrt-ramips-mt76x8-skw92a-squashfs-sysupgrade.bin on a TFTP server
2. Connect to serial console at USB3 on EVB (57600 8N1)
3. Connect ethernet between port 1 (not WAN) an your TFTP server (e.g.
192.168.11.20)
4. Start terminal software (e.g. screen /dev/ttyUSB0 57600) on PC
5. Apply power to EVB
6. Interrupt u-boot with keypress of "2"
7. At u-boot prompts:
Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N) Y
Input device IP (10.10.10.123) ==:192.168.11.21
Input server IP (10.10.10.3) ==:192.168.11.20
Input Linux Kernel filename (root_uImage) ==:openwrt-ramips-mt76x8-skw92a-squashfs-sysupgrade.bin
8. When transfer is complete or as OpenWrt begins booting, move ethernet to
port 0 (WAN).
Signed-off-by: Russell Senior <russell@personaltelco.net>
2018-11-25 11:39:19 +00:00
|
|
|
DTS := SKW92A
|
|
|
|
|
IMAGE_SIZE := 16064k
|
|
|
|
|
DEVICE_TITLE := Skylab SKW92A
|
|
|
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ohci
|
|
|
|
|
endef
|
2018-11-26 11:34:48 +00:00
|
|
|
TARGET_DEVICES += skylab_skw92a
|
ramips: add support for Skylab SKW92A in EVB
Specifically, SKW92A_E16, described here:
http://www.skylabmodule.com/wp-content/uploads/SkyLab_SKW92A_V1.04_datasheet.pdf
Specification:
- MediaTek MT7628N/N (580 Mhz)
- 64 MB of RAM
- 16 MB of FLASH
- 2T2R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x u.FL
- Power by micro-USB connector at USB1 on EVB
- UART via micro-USB connector at USB3 on EVB (57600 8n1)
- 5x Ethernet LEDs
- 1x WLAN LEDs
- 1x WPS LED connected by jumper wire from I2S_CK on J20 to WPS_LED pin hole next
to daughter board on EVB
- WPS/Reset button (S2 on EVB)
- RESET button (S1 on EVB) is *not* connected to RST hole next to daughter board
Flash instruction:
>From Skylab firmware:
1. Associate with SKYLAP_AP
2. In a browser, load: http://10.10.10.254/
3. Username/password: admin/admin
4. In web admin interface: Administration / Upload Firmware, browse to
sysupgrade image, apply, flash will fail with a message:
Not a valid firmware. *** Warning: "/var/tmpFW" has corrupted data!
5. Telnet to 10.10.10.254, drops you into a root shell with no credentials
6. # cd /var
7. # mtd_write -r write tmpFW mtd4
Unlocking mtd4 ...
Writing from tmpFW to mtd4 ... [e]
8. When flash has completed, you will have booted into your firmware.
>From U-boot via TFTP and initramfs:
1. Place openwrt-ramips-mt76x8-skw92a-initramfs-kernel.bin on a TFTP server
2. Connect to serial console at USB3 on EVB
3. Connect ethernet between port 1 (not WAN) and your TFTP server (e.g.
192.168.11.20)
4. Start terminal software (e.g. screen /dev/ttyUSB0 57600) on PC
5. Apply power to EVB
6. Interrupt u-boot with keypress of "1"
7. At u-boot prompts:
Input device IP (10.10.10.123) ==:192.168.11.21
Input server IP (10.10.10.3) ==:192.168.11.20
Input Linux Kernel filename (root_uImage) ==:openwrt-ramips-mt76x8-skw92a-initramfs-kernel.bin
8. Move ethernet to port 0 (WAN) on EVB
9. At new OpenWrt console shell, fetch squashfs-sysupgrade image and flash
with sysupgrade.
>From U-boot via TFTP direct flash:
1. Place openwrt-ramips-mt76x8-skw92a-squashfs-sysupgrade.bin on a TFTP server
2. Connect to serial console at USB3 on EVB (57600 8N1)
3. Connect ethernet between port 1 (not WAN) an your TFTP server (e.g.
192.168.11.20)
4. Start terminal software (e.g. screen /dev/ttyUSB0 57600) on PC
5. Apply power to EVB
6. Interrupt u-boot with keypress of "2"
7. At u-boot prompts:
Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N) Y
Input device IP (10.10.10.123) ==:192.168.11.21
Input server IP (10.10.10.3) ==:192.168.11.20
Input Linux Kernel filename (root_uImage) ==:openwrt-ramips-mt76x8-skw92a-squashfs-sysupgrade.bin
8. When transfer is complete or as OpenWrt begins booting, move ethernet to
port 0 (WAN).
Signed-off-by: Russell Senior <russell@personaltelco.net>
2018-11-25 11:39:19 +00:00
|
|
|
|
2018-06-26 23:24:39 +00:00
|
|
|
define Device/tplink_tl-wa801nd-v5
|
|
|
|
|
$(Device/tplink)
|
|
|
|
|
DTS := TL-WA801NDV5
|
|
|
|
|
IMAGE_SIZE := 7808k
|
|
|
|
|
DEVICE_TITLE := TP-Link TL-WA801ND v5
|
|
|
|
|
TPLINK_FLASHLAYOUT := 8Mmtk
|
|
|
|
|
TPLINK_HWID := 0x08010005
|
|
|
|
|
TPLINK_HWREV := 0x1
|
|
|
|
|
TPLINK_HWREVADD := 0x5
|
|
|
|
|
TPLINK_HVERSION := 3
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += tplink_tl-wa801nd-v5
|
|
|
|
|
|
2018-12-18 07:00:52 +00:00
|
|
|
define Device/tplink_tl-wr802n-v4
|
|
|
|
|
$(Device/tplink)
|
|
|
|
|
DTS := TL-WR802NV4
|
|
|
|
|
IMAGE_SIZE := 7808k
|
|
|
|
|
DEVICE_TITLE := TP-Link TL-WR802N v4
|
|
|
|
|
TPLINK_FLASHLAYOUT := 8Mmtk
|
|
|
|
|
TPLINK_HWID := 0x08020004
|
|
|
|
|
TPLINK_HWREV := 0x1
|
|
|
|
|
TPLINK_HWREVADD := 0x4
|
|
|
|
|
TPLINK_HVERSION := 3
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += tplink_tl-wr802n-v4
|
|
|
|
|
|
ramips: add support for TP-Link TL-WR840N v4 and TL-WR841N v13
TP-Link TL-WR840N v4 and TL-WR841N v13 are simple N300 routers with
5-port FE switch and non-detachable antennas. Both are very similar
and are based on MediaTek MT7628NN (aka MT7628N) WiSoC.
The difference between these two models is in number of available
LEDs, buttons and power input switch.
This work is partially based on GitHub PR#974.
Specification:
- MT7628N/N (580 MHz)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- TL-WR840N v4: 5x LED (GPIO-controlled), 1x button
- TL-WR841N v13: 8x LED (GPIO-controlled*), 2x button, power input
switch
* WAN LED in TL-WR841N v13 is a dual-color, dual-leads type which isn't
(fully) supported by gpio-leds driver. This type of LED requires both
GPIOs state change at the same time to select color or turn it off.
For now, we support/use only the green part of the LED.
Factory image notes:
These devices use version 3 of TP-Link header, fortunately without RSA
signature (at least in case of devices sold in Europe). The difference
lays in the requirement for a non-zero value in "Additional Hardware
Version" field. Ideally, it should match the value stored in vendor
firmware header on device ("0x4"/"0x13" for these devices) but it seems
that anything other than "0" is correct.
We are able to prepare factory firwmare file which is accepted and
(almost) correctly flashed from the vendor GUI. As it turned out, it
accepts files without U-Boot image with second header at the beginning
but due to some kind of bug in upgrade routine, flashed image gets
corrupted before it's written to flash.
Tests showed that the GUI upgrade routine copies value of "Additional
Hardware Version" from existing firmware into offset "0x2023c" in
provided file, _before_ storing it in flash. In case of vendor firmware
upgrade files (which all include U-Boot image and two headers), this
offset points to the matching field in kernel+rootfs firmware part
header. Unfortunately, in case of LEDE factory image file which contains
only one header, it points to the offset "0x2023c" in kernel image. This
leads to a corrupted kernel and ends up with a "soft-bricked" device.
The good news is that U-Boot in these devices contains well known tftp
recovery mode, which can be triggered with "reset" button. What's more,
in comparison to some of older MediaTek based TP-Link devices, this
recovery mode doesn't write whole file at offset "0x0" in flash, without
verifying provided file in advance. In case of recovery mode in these
devices, first "0x20000" bytes are always skipped and "0x7a0000" bytes
from rest of the file are stored in flash at offset "0x20000".
Flash instruction:
Until (if at all) TP-Link fixes described problem, the only way to flash
LEDE image in these devices is to use tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "lede-ramips-mt7628-tl-wr84...-squashfs-tftp-recovery.bin"
to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed for around 6-7 seconds, until
device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.
To access U-Boot CLI, keep pressed "4" key during boot.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-21 12:16:15 +00:00
|
|
|
define Device/tl-wr840n-v4
|
2017-12-17 09:44:41 +00:00
|
|
|
$(Device/tplink)
|
ramips: add support for TP-Link TL-WR840N v4 and TL-WR841N v13
TP-Link TL-WR840N v4 and TL-WR841N v13 are simple N300 routers with
5-port FE switch and non-detachable antennas. Both are very similar
and are based on MediaTek MT7628NN (aka MT7628N) WiSoC.
The difference between these two models is in number of available
LEDs, buttons and power input switch.
This work is partially based on GitHub PR#974.
Specification:
- MT7628N/N (580 MHz)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- TL-WR840N v4: 5x LED (GPIO-controlled), 1x button
- TL-WR841N v13: 8x LED (GPIO-controlled*), 2x button, power input
switch
* WAN LED in TL-WR841N v13 is a dual-color, dual-leads type which isn't
(fully) supported by gpio-leds driver. This type of LED requires both
GPIOs state change at the same time to select color or turn it off.
For now, we support/use only the green part of the LED.
Factory image notes:
These devices use version 3 of TP-Link header, fortunately without RSA
signature (at least in case of devices sold in Europe). The difference
lays in the requirement for a non-zero value in "Additional Hardware
Version" field. Ideally, it should match the value stored in vendor
firmware header on device ("0x4"/"0x13" for these devices) but it seems
that anything other than "0" is correct.
We are able to prepare factory firwmare file which is accepted and
(almost) correctly flashed from the vendor GUI. As it turned out, it
accepts files without U-Boot image with second header at the beginning
but due to some kind of bug in upgrade routine, flashed image gets
corrupted before it's written to flash.
Tests showed that the GUI upgrade routine copies value of "Additional
Hardware Version" from existing firmware into offset "0x2023c" in
provided file, _before_ storing it in flash. In case of vendor firmware
upgrade files (which all include U-Boot image and two headers), this
offset points to the matching field in kernel+rootfs firmware part
header. Unfortunately, in case of LEDE factory image file which contains
only one header, it points to the offset "0x2023c" in kernel image. This
leads to a corrupted kernel and ends up with a "soft-bricked" device.
The good news is that U-Boot in these devices contains well known tftp
recovery mode, which can be triggered with "reset" button. What's more,
in comparison to some of older MediaTek based TP-Link devices, this
recovery mode doesn't write whole file at offset "0x0" in flash, without
verifying provided file in advance. In case of recovery mode in these
devices, first "0x20000" bytes are always skipped and "0x7a0000" bytes
from rest of the file are stored in flash at offset "0x20000".
Flash instruction:
Until (if at all) TP-Link fixes described problem, the only way to flash
LEDE image in these devices is to use tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "lede-ramips-mt7628-tl-wr84...-squashfs-tftp-recovery.bin"
to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed for around 6-7 seconds, until
device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.
To access U-Boot CLI, keep pressed "4" key during boot.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-21 12:16:15 +00:00
|
|
|
DTS := TL-WR840NV4
|
|
|
|
|
IMAGE_SIZE := 7808k
|
|
|
|
|
DEVICE_TITLE := TP-Link TL-WR840N v4
|
2017-10-03 10:46:09 +00:00
|
|
|
TPLINK_FLASHLAYOUT := 8Mmtk
|
|
|
|
|
TPLINK_HWID := 0x08400004
|
|
|
|
|
TPLINK_HWREV := 0x1
|
|
|
|
|
TPLINK_HWREVADD := 0x4
|
|
|
|
|
TPLINK_HVERSION := 3
|
ramips: add support for TP-Link TL-WR840N v4 and TL-WR841N v13
TP-Link TL-WR840N v4 and TL-WR841N v13 are simple N300 routers with
5-port FE switch and non-detachable antennas. Both are very similar
and are based on MediaTek MT7628NN (aka MT7628N) WiSoC.
The difference between these two models is in number of available
LEDs, buttons and power input switch.
This work is partially based on GitHub PR#974.
Specification:
- MT7628N/N (580 MHz)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- TL-WR840N v4: 5x LED (GPIO-controlled), 1x button
- TL-WR841N v13: 8x LED (GPIO-controlled*), 2x button, power input
switch
* WAN LED in TL-WR841N v13 is a dual-color, dual-leads type which isn't
(fully) supported by gpio-leds driver. This type of LED requires both
GPIOs state change at the same time to select color or turn it off.
For now, we support/use only the green part of the LED.
Factory image notes:
These devices use version 3 of TP-Link header, fortunately without RSA
signature (at least in case of devices sold in Europe). The difference
lays in the requirement for a non-zero value in "Additional Hardware
Version" field. Ideally, it should match the value stored in vendor
firmware header on device ("0x4"/"0x13" for these devices) but it seems
that anything other than "0" is correct.
We are able to prepare factory firwmare file which is accepted and
(almost) correctly flashed from the vendor GUI. As it turned out, it
accepts files without U-Boot image with second header at the beginning
but due to some kind of bug in upgrade routine, flashed image gets
corrupted before it's written to flash.
Tests showed that the GUI upgrade routine copies value of "Additional
Hardware Version" from existing firmware into offset "0x2023c" in
provided file, _before_ storing it in flash. In case of vendor firmware
upgrade files (which all include U-Boot image and two headers), this
offset points to the matching field in kernel+rootfs firmware part
header. Unfortunately, in case of LEDE factory image file which contains
only one header, it points to the offset "0x2023c" in kernel image. This
leads to a corrupted kernel and ends up with a "soft-bricked" device.
The good news is that U-Boot in these devices contains well known tftp
recovery mode, which can be triggered with "reset" button. What's more,
in comparison to some of older MediaTek based TP-Link devices, this
recovery mode doesn't write whole file at offset "0x0" in flash, without
verifying provided file in advance. In case of recovery mode in these
devices, first "0x20000" bytes are always skipped and "0x7a0000" bytes
from rest of the file are stored in flash at offset "0x20000".
Flash instruction:
Until (if at all) TP-Link fixes described problem, the only way to flash
LEDE image in these devices is to use tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "lede-ramips-mt7628-tl-wr84...-squashfs-tftp-recovery.bin"
to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed for around 6-7 seconds, until
device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.
To access U-Boot CLI, keep pressed "4" key during boot.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-21 12:16:15 +00:00
|
|
|
endef
|
2017-12-10 22:45:20 +00:00
|
|
|
TARGET_DEVICES += tl-wr840n-v4
|
ramips: add support for TP-Link TL-WR840N v4 and TL-WR841N v13
TP-Link TL-WR840N v4 and TL-WR841N v13 are simple N300 routers with
5-port FE switch and non-detachable antennas. Both are very similar
and are based on MediaTek MT7628NN (aka MT7628N) WiSoC.
The difference between these two models is in number of available
LEDs, buttons and power input switch.
This work is partially based on GitHub PR#974.
Specification:
- MT7628N/N (580 MHz)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- TL-WR840N v4: 5x LED (GPIO-controlled), 1x button
- TL-WR841N v13: 8x LED (GPIO-controlled*), 2x button, power input
switch
* WAN LED in TL-WR841N v13 is a dual-color, dual-leads type which isn't
(fully) supported by gpio-leds driver. This type of LED requires both
GPIOs state change at the same time to select color or turn it off.
For now, we support/use only the green part of the LED.
Factory image notes:
These devices use version 3 of TP-Link header, fortunately without RSA
signature (at least in case of devices sold in Europe). The difference
lays in the requirement for a non-zero value in "Additional Hardware
Version" field. Ideally, it should match the value stored in vendor
firmware header on device ("0x4"/"0x13" for these devices) but it seems
that anything other than "0" is correct.
We are able to prepare factory firwmare file which is accepted and
(almost) correctly flashed from the vendor GUI. As it turned out, it
accepts files without U-Boot image with second header at the beginning
but due to some kind of bug in upgrade routine, flashed image gets
corrupted before it's written to flash.
Tests showed that the GUI upgrade routine copies value of "Additional
Hardware Version" from existing firmware into offset "0x2023c" in
provided file, _before_ storing it in flash. In case of vendor firmware
upgrade files (which all include U-Boot image and two headers), this
offset points to the matching field in kernel+rootfs firmware part
header. Unfortunately, in case of LEDE factory image file which contains
only one header, it points to the offset "0x2023c" in kernel image. This
leads to a corrupted kernel and ends up with a "soft-bricked" device.
The good news is that U-Boot in these devices contains well known tftp
recovery mode, which can be triggered with "reset" button. What's more,
in comparison to some of older MediaTek based TP-Link devices, this
recovery mode doesn't write whole file at offset "0x0" in flash, without
verifying provided file in advance. In case of recovery mode in these
devices, first "0x20000" bytes are always skipped and "0x7a0000" bytes
from rest of the file are stored in flash at offset "0x20000".
Flash instruction:
Until (if at all) TP-Link fixes described problem, the only way to flash
LEDE image in these devices is to use tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "lede-ramips-mt7628-tl-wr84...-squashfs-tftp-recovery.bin"
to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed for around 6-7 seconds, until
device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.
To access U-Boot CLI, keep pressed "4" key during boot.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-21 12:16:15 +00:00
|
|
|
|
2017-11-08 13:00:06 +00:00
|
|
|
define Device/tl-wr840n-v5
|
|
|
|
|
DTS := TL-WR840NV5
|
2017-12-24 16:00:13 +00:00
|
|
|
IMAGE_SIZE := 3904k
|
2017-11-08 13:00:06 +00:00
|
|
|
DEVICE_TITLE := TP-Link TL-WR840N v5
|
|
|
|
|
TPLINK_FLASHLAYOUT := 4Mmtk
|
|
|
|
|
TPLINK_HWID := 0x08400005
|
|
|
|
|
TPLINK_HWREV := 0x1
|
|
|
|
|
TPLINK_HWREVADD := 0x5
|
|
|
|
|
TPLINK_HVERSION := 3
|
|
|
|
|
KERNEL := $(KERNEL_DTB)
|
|
|
|
|
KERNEL_INITRAMFS := $(KERNEL_DTB) | tplink-v2-header -e
|
|
|
|
|
IMAGE/sysupgrade.bin := tplink-v2-image -s -e | append-metadata | \
|
|
|
|
|
check-size $$$$(IMAGE_SIZE)
|
|
|
|
|
endef
|
2017-12-10 22:45:20 +00:00
|
|
|
TARGET_DEVICES += tl-wr840n-v5
|
2017-11-08 13:00:06 +00:00
|
|
|
|
ramips: add support for TP-Link TL-WR840N v4 and TL-WR841N v13
TP-Link TL-WR840N v4 and TL-WR841N v13 are simple N300 routers with
5-port FE switch and non-detachable antennas. Both are very similar
and are based on MediaTek MT7628NN (aka MT7628N) WiSoC.
The difference between these two models is in number of available
LEDs, buttons and power input switch.
This work is partially based on GitHub PR#974.
Specification:
- MT7628N/N (580 MHz)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- TL-WR840N v4: 5x LED (GPIO-controlled), 1x button
- TL-WR841N v13: 8x LED (GPIO-controlled*), 2x button, power input
switch
* WAN LED in TL-WR841N v13 is a dual-color, dual-leads type which isn't
(fully) supported by gpio-leds driver. This type of LED requires both
GPIOs state change at the same time to select color or turn it off.
For now, we support/use only the green part of the LED.
Factory image notes:
These devices use version 3 of TP-Link header, fortunately without RSA
signature (at least in case of devices sold in Europe). The difference
lays in the requirement for a non-zero value in "Additional Hardware
Version" field. Ideally, it should match the value stored in vendor
firmware header on device ("0x4"/"0x13" for these devices) but it seems
that anything other than "0" is correct.
We are able to prepare factory firwmare file which is accepted and
(almost) correctly flashed from the vendor GUI. As it turned out, it
accepts files without U-Boot image with second header at the beginning
but due to some kind of bug in upgrade routine, flashed image gets
corrupted before it's written to flash.
Tests showed that the GUI upgrade routine copies value of "Additional
Hardware Version" from existing firmware into offset "0x2023c" in
provided file, _before_ storing it in flash. In case of vendor firmware
upgrade files (which all include U-Boot image and two headers), this
offset points to the matching field in kernel+rootfs firmware part
header. Unfortunately, in case of LEDE factory image file which contains
only one header, it points to the offset "0x2023c" in kernel image. This
leads to a corrupted kernel and ends up with a "soft-bricked" device.
The good news is that U-Boot in these devices contains well known tftp
recovery mode, which can be triggered with "reset" button. What's more,
in comparison to some of older MediaTek based TP-Link devices, this
recovery mode doesn't write whole file at offset "0x0" in flash, without
verifying provided file in advance. In case of recovery mode in these
devices, first "0x20000" bytes are always skipped and "0x7a0000" bytes
from rest of the file are stored in flash at offset "0x20000".
Flash instruction:
Until (if at all) TP-Link fixes described problem, the only way to flash
LEDE image in these devices is to use tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "lede-ramips-mt7628-tl-wr84...-squashfs-tftp-recovery.bin"
to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed for around 6-7 seconds, until
device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.
To access U-Boot CLI, keep pressed "4" key during boot.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-21 12:16:15 +00:00
|
|
|
define Device/tl-wr841n-v13
|
2017-12-17 09:44:41 +00:00
|
|
|
$(Device/tplink)
|
ramips: add support for TP-Link TL-WR840N v4 and TL-WR841N v13
TP-Link TL-WR840N v4 and TL-WR841N v13 are simple N300 routers with
5-port FE switch and non-detachable antennas. Both are very similar
and are based on MediaTek MT7628NN (aka MT7628N) WiSoC.
The difference between these two models is in number of available
LEDs, buttons and power input switch.
This work is partially based on GitHub PR#974.
Specification:
- MT7628N/N (580 MHz)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- TL-WR840N v4: 5x LED (GPIO-controlled), 1x button
- TL-WR841N v13: 8x LED (GPIO-controlled*), 2x button, power input
switch
* WAN LED in TL-WR841N v13 is a dual-color, dual-leads type which isn't
(fully) supported by gpio-leds driver. This type of LED requires both
GPIOs state change at the same time to select color or turn it off.
For now, we support/use only the green part of the LED.
Factory image notes:
These devices use version 3 of TP-Link header, fortunately without RSA
signature (at least in case of devices sold in Europe). The difference
lays in the requirement for a non-zero value in "Additional Hardware
Version" field. Ideally, it should match the value stored in vendor
firmware header on device ("0x4"/"0x13" for these devices) but it seems
that anything other than "0" is correct.
We are able to prepare factory firwmare file which is accepted and
(almost) correctly flashed from the vendor GUI. As it turned out, it
accepts files without U-Boot image with second header at the beginning
but due to some kind of bug in upgrade routine, flashed image gets
corrupted before it's written to flash.
Tests showed that the GUI upgrade routine copies value of "Additional
Hardware Version" from existing firmware into offset "0x2023c" in
provided file, _before_ storing it in flash. In case of vendor firmware
upgrade files (which all include U-Boot image and two headers), this
offset points to the matching field in kernel+rootfs firmware part
header. Unfortunately, in case of LEDE factory image file which contains
only one header, it points to the offset "0x2023c" in kernel image. This
leads to a corrupted kernel and ends up with a "soft-bricked" device.
The good news is that U-Boot in these devices contains well known tftp
recovery mode, which can be triggered with "reset" button. What's more,
in comparison to some of older MediaTek based TP-Link devices, this
recovery mode doesn't write whole file at offset "0x0" in flash, without
verifying provided file in advance. In case of recovery mode in these
devices, first "0x20000" bytes are always skipped and "0x7a0000" bytes
from rest of the file are stored in flash at offset "0x20000".
Flash instruction:
Until (if at all) TP-Link fixes described problem, the only way to flash
LEDE image in these devices is to use tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "lede-ramips-mt7628-tl-wr84...-squashfs-tftp-recovery.bin"
to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed for around 6-7 seconds, until
device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.
To access U-Boot CLI, keep pressed "4" key during boot.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-21 12:16:15 +00:00
|
|
|
DTS := TL-WR841NV13
|
2017-12-17 09:44:41 +00:00
|
|
|
IMAGE_SIZE := 7808k
|
ramips: add support for TP-Link TL-WR840N v4 and TL-WR841N v13
TP-Link TL-WR840N v4 and TL-WR841N v13 are simple N300 routers with
5-port FE switch and non-detachable antennas. Both are very similar
and are based on MediaTek MT7628NN (aka MT7628N) WiSoC.
The difference between these two models is in number of available
LEDs, buttons and power input switch.
This work is partially based on GitHub PR#974.
Specification:
- MT7628N/N (580 MHz)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- TL-WR840N v4: 5x LED (GPIO-controlled), 1x button
- TL-WR841N v13: 8x LED (GPIO-controlled*), 2x button, power input
switch
* WAN LED in TL-WR841N v13 is a dual-color, dual-leads type which isn't
(fully) supported by gpio-leds driver. This type of LED requires both
GPIOs state change at the same time to select color or turn it off.
For now, we support/use only the green part of the LED.
Factory image notes:
These devices use version 3 of TP-Link header, fortunately without RSA
signature (at least in case of devices sold in Europe). The difference
lays in the requirement for a non-zero value in "Additional Hardware
Version" field. Ideally, it should match the value stored in vendor
firmware header on device ("0x4"/"0x13" for these devices) but it seems
that anything other than "0" is correct.
We are able to prepare factory firwmare file which is accepted and
(almost) correctly flashed from the vendor GUI. As it turned out, it
accepts files without U-Boot image with second header at the beginning
but due to some kind of bug in upgrade routine, flashed image gets
corrupted before it's written to flash.
Tests showed that the GUI upgrade routine copies value of "Additional
Hardware Version" from existing firmware into offset "0x2023c" in
provided file, _before_ storing it in flash. In case of vendor firmware
upgrade files (which all include U-Boot image and two headers), this
offset points to the matching field in kernel+rootfs firmware part
header. Unfortunately, in case of LEDE factory image file which contains
only one header, it points to the offset "0x2023c" in kernel image. This
leads to a corrupted kernel and ends up with a "soft-bricked" device.
The good news is that U-Boot in these devices contains well known tftp
recovery mode, which can be triggered with "reset" button. What's more,
in comparison to some of older MediaTek based TP-Link devices, this
recovery mode doesn't write whole file at offset "0x0" in flash, without
verifying provided file in advance. In case of recovery mode in these
devices, first "0x20000" bytes are always skipped and "0x7a0000" bytes
from rest of the file are stored in flash at offset "0x20000".
Flash instruction:
Until (if at all) TP-Link fixes described problem, the only way to flash
LEDE image in these devices is to use tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "lede-ramips-mt7628-tl-wr84...-squashfs-tftp-recovery.bin"
to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed for around 6-7 seconds, until
device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.
To access U-Boot CLI, keep pressed "4" key during boot.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-21 12:16:15 +00:00
|
|
|
DEVICE_TITLE := TP-Link TL-WR841N v13
|
2017-12-17 09:44:41 +00:00
|
|
|
TPLINK_FLASHLAYOUT := 8Mmtk
|
2017-10-03 10:46:09 +00:00
|
|
|
TPLINK_HWID := 0x08410013
|
|
|
|
|
TPLINK_HWREV := 0x268
|
|
|
|
|
TPLINK_HWREVADD := 0x13
|
2017-12-17 09:44:41 +00:00
|
|
|
TPLINK_HVERSION := 3
|
ramips: add support for TP-Link TL-WR840N v4 and TL-WR841N v13
TP-Link TL-WR840N v4 and TL-WR841N v13 are simple N300 routers with
5-port FE switch and non-detachable antennas. Both are very similar
and are based on MediaTek MT7628NN (aka MT7628N) WiSoC.
The difference between these two models is in number of available
LEDs, buttons and power input switch.
This work is partially based on GitHub PR#974.
Specification:
- MT7628N/N (580 MHz)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- TL-WR840N v4: 5x LED (GPIO-controlled), 1x button
- TL-WR841N v13: 8x LED (GPIO-controlled*), 2x button, power input
switch
* WAN LED in TL-WR841N v13 is a dual-color, dual-leads type which isn't
(fully) supported by gpio-leds driver. This type of LED requires both
GPIOs state change at the same time to select color or turn it off.
For now, we support/use only the green part of the LED.
Factory image notes:
These devices use version 3 of TP-Link header, fortunately without RSA
signature (at least in case of devices sold in Europe). The difference
lays in the requirement for a non-zero value in "Additional Hardware
Version" field. Ideally, it should match the value stored in vendor
firmware header on device ("0x4"/"0x13" for these devices) but it seems
that anything other than "0" is correct.
We are able to prepare factory firwmare file which is accepted and
(almost) correctly flashed from the vendor GUI. As it turned out, it
accepts files without U-Boot image with second header at the beginning
but due to some kind of bug in upgrade routine, flashed image gets
corrupted before it's written to flash.
Tests showed that the GUI upgrade routine copies value of "Additional
Hardware Version" from existing firmware into offset "0x2023c" in
provided file, _before_ storing it in flash. In case of vendor firmware
upgrade files (which all include U-Boot image and two headers), this
offset points to the matching field in kernel+rootfs firmware part
header. Unfortunately, in case of LEDE factory image file which contains
only one header, it points to the offset "0x2023c" in kernel image. This
leads to a corrupted kernel and ends up with a "soft-bricked" device.
The good news is that U-Boot in these devices contains well known tftp
recovery mode, which can be triggered with "reset" button. What's more,
in comparison to some of older MediaTek based TP-Link devices, this
recovery mode doesn't write whole file at offset "0x0" in flash, without
verifying provided file in advance. In case of recovery mode in these
devices, first "0x20000" bytes are always skipped and "0x7a0000" bytes
from rest of the file are stored in flash at offset "0x20000".
Flash instruction:
Until (if at all) TP-Link fixes described problem, the only way to flash
LEDE image in these devices is to use tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "lede-ramips-mt7628-tl-wr84...-squashfs-tftp-recovery.bin"
to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed for around 6-7 seconds, until
device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.
To access U-Boot CLI, keep pressed "4" key during boot.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-06-21 12:16:15 +00:00
|
|
|
endef
|
2017-12-10 22:45:20 +00:00
|
|
|
TARGET_DEVICES += tl-wr841n-v13
|
2017-05-17 10:18:45 +00:00
|
|
|
|
2018-01-09 11:25:53 +00:00
|
|
|
define Device/tplink_c20-v4
|
|
|
|
|
$(Device/tplink)
|
|
|
|
|
DTS := ArcherC20v4
|
|
|
|
|
IMAGE_SIZE := 7808k
|
|
|
|
|
DEVICE_TITLE := TP-Link ArcherC20 v4
|
|
|
|
|
TPLINK_FLASHLAYOUT := 8Mmtk
|
|
|
|
|
TPLINK_HWID := 0xc200004
|
|
|
|
|
TPLINK_HWREV := 0x1
|
|
|
|
|
TPLINK_HWREVADD := 0x4
|
|
|
|
|
TPLINK_HVERSION := 3
|
2018-11-30 10:10:29 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt76x0e
|
2018-01-09 11:25:53 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += tplink_c20-v4
|
|
|
|
|
|
2018-01-28 18:49:38 +00:00
|
|
|
define Device/tplink_c50-v3
|
|
|
|
|
$(Device/tplink)
|
|
|
|
|
DTS := ArcherC50V3
|
|
|
|
|
IMAGE_SIZE := 7808k
|
|
|
|
|
DEVICE_TITLE := TP-Link ArcherC50 v3
|
|
|
|
|
TPLINK_FLASHLAYOUT := 8Mmtk
|
|
|
|
|
TPLINK_HWID := 0x001D9BA4
|
|
|
|
|
TPLINK_HWREV := 0x79
|
|
|
|
|
TPLINK_HWREVADD := 0x1
|
|
|
|
|
TPLINK_HVERSION := 3
|
2018-11-30 10:10:29 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt76x2
|
2018-01-28 18:49:38 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += tplink_c50-v3
|
|
|
|
|
|
ramips: add support for Archer C50 v4
This adds support for the TP-Link Archer C50 v4.
It uses the same hardware as the v3 variant, sharing the same FCC-ID.
CPU: MediaTek MT7628 (580MHz)
RAM: 64M DDR2
FLASH: 8M SPI
WiFi: 2.4GHz 2x2 MT7628 b/g/n integrated
WiFI: 5GHz 2x2 MT7612 a/n/ac
ETH: 1x WAN 4x LAN
LED: Power, WiFi2, WiFi5, LAN, WAN, WPS
BTN: WPS/WiFi, RESET
UART: Near ETH ports, 115200 8n1, TP-Link pinout
Create Factory image
--------------------
As all installation methods require a U-Boot to be integrated into the
Image (and we do not ship one with the image) we are not able to create
an image in the OpenWRT build-process.
Download a TP-Link image from their Wesite and a OpenWRT sysupgrade
image for the device and build yourself a factory image like following:
TP-Link image: tpl.bin
OpenWRT sysupgrade image: owrt.bin
> dd if=tpl.bin of=boot.bin bs=131584 count=1
> cat owrt.bin >> boot.bin
Installing via Web-UI
---------------------
Upload the boot.bin via TP-Links firmware upgrade tool in the
web-interface.
Installing via Recovery
-----------------------
Activate Web-Recovery by beginning the upgrade Process with a
Firmware-Image from TP-Link. After starting the Firmware Upgrade,
wait ~3 seconds (When update status is switching to 0%), then
disconnect the power supply from the device. Upgrade flag (which
activates Web-Recovery) is written before the OS-image is touched and
removed after write is succesfull, so this procedure should be safe.
Plug the power back in. It will come up in Recovery-Mode on 192.168.0.1.
When active, all LEDs but the WPS LED are off.
Remeber to assign yourself a static IP-address as DHCP is not active in
this mode.
The boot.bin can now be uploaded and flashed using the web-recovery.
Installing via TFTP
-------------------
Prepare an image like following (Filenames from factory image steps
apply here)
> dd if=/dev/zero of=tp_recovery.bin bs=196608 count=1
> dd if=tpl.bin of=tmp.bin bs=131584 count=1
> dd if=tmp.bin of=boot.bin bs=512 skip=1
> cat boot.bin >> tp_recovery.bin
> cat owrt.bin >> tp_recovery.bin
Place tp_recovery.bin in root directory of TFTP server and listen on
192.168.0.66/24.
Connect router LAN ports with your computer and power up the router
while pressing the reset button. The router will download the image via
tftp and after ~1 Minute reboot into OpenWRT.
U-Boot CLI
----------
U-Boot CLI can be activated by holding down '4' on bootup.
Dual U-Boot
-----------
This is the first TP-Link MediaTek device to feature a split-uboot
design. The first (factory-uboot) provides recovery via TFTP and HTTP,
jumping straight into the second (firmware-uboot) if no recovery needs
to be performed. The firmware-uboot unpacks and executed the kernel.
Web-Recovery
------------
TP-Link integrated a new Web-Recovery like the one on the Archer C7v4 /
TL-WR1043v5. Stock-firmware sets a flag in the "romfile" partition
before beginning to write and removes it afterwards. If the router boots
with this flag set, bootloader will automatically start Web-recovery and
listens on 192.168.0.1. This way, the vendor-firmware or an OpenWRT
factory image can be written.
By doing the same while performing sysupgrade, we can take advantage of
the Web-recovery in OpenWRT.
It is important to note that Web-Recovery is only based on this flag. It
can't detect e.g. a crashing kernel or other means. Once activated it
won't boot the OS before a recovery action (either via TFTP or HTTP) is
performed. This recovery-mode is indicated by an illuminated WPS-LED on
boot.
Signed-off-by: David Bauer <mail@david-bauer.net>
2018-12-31 15:24:26 +00:00
|
|
|
define Device/tplink_c50-v4
|
|
|
|
|
$(Device/tplink)
|
|
|
|
|
DTS := ArcherC50V4
|
|
|
|
|
IMAGE_SIZE := 7616k
|
|
|
|
|
DEVICE_TITLE := TP-Link ArcherC50 v4
|
|
|
|
|
TPLINK_FLASHLAYOUT := 8MSUmtk
|
|
|
|
|
TPLINK_HWID := 0x001D589B
|
|
|
|
|
TPLINK_HWREV := 0x93
|
|
|
|
|
TPLINK_HWREVADD := 0x2
|
|
|
|
|
TPLINK_HVERSION := 3
|
|
|
|
|
DEVICE_PACKAGES := kmod-mt76x2
|
|
|
|
|
IMAGES := sysupgrade.bin
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += tplink_c50-v4
|
|
|
|
|
|
2018-08-26 19:11:59 +00:00
|
|
|
define Device/tplink_tl-mr3020-v3
|
|
|
|
|
$(Device/tplink)
|
|
|
|
|
DTS := TL-MR3020V3
|
|
|
|
|
IMAGE_SIZE := 7808k
|
|
|
|
|
DEVICE_TITLE := TP-Link TL-MR3020 v3
|
|
|
|
|
TPLINK_FLASHLAYOUT := 8Mmtk
|
|
|
|
|
TPLINK_HWID := 0x30200003
|
|
|
|
|
TPLINK_HWREV := 0x3
|
|
|
|
|
TPLINK_HWREVADD := 0x3
|
|
|
|
|
TPLINK_HVERSION := 3
|
|
|
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ohci kmod-usb-ledtrig-usbport
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += tplink_tl-mr3020-v3
|
|
|
|
|
|
2017-12-15 14:57:49 +00:00
|
|
|
define Device/tplink_tl-mr3420-v5
|
|
|
|
|
$(Device/tplink)
|
|
|
|
|
DTS := TL-MR3420V5
|
|
|
|
|
IMAGE_SIZE := 7808k
|
|
|
|
|
DEVICE_TITLE := TP-Link TL-MR3420 v5
|
|
|
|
|
TPLINK_FLASHLAYOUT := 8Mmtk
|
|
|
|
|
TPLINK_HWID := 0x34200005
|
|
|
|
|
TPLINK_HWREV := 0x5
|
|
|
|
|
TPLINK_HWREVADD := 0x5
|
|
|
|
|
TPLINK_HVERSION := 3
|
|
|
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ohci kmod-usb-ledtrig-usbport
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += tplink_tl-mr3420-v5
|
|
|
|
|
|
2018-05-30 15:41:53 +00:00
|
|
|
define Device/tplink_tl-wr842n-v5
|
|
|
|
|
$(Device/tplink)
|
|
|
|
|
DTS := TL-WR842NV5
|
|
|
|
|
IMAGE_SIZE := 7808k
|
|
|
|
|
DEVICE_TITLE := TP-Link TL-WR842N v5
|
|
|
|
|
TPLINK_FLASHLAYOUT := 8Mmtk
|
|
|
|
|
TPLINK_HWID := 0x08420005
|
|
|
|
|
TPLINK_HWREV := 0x5
|
|
|
|
|
TPLINK_HWREVADD := 0x5
|
|
|
|
|
TPLINK_HVERSION := 3
|
|
|
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ohci kmod-usb-ledtrig-usbport
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += tplink_tl-wr842n-v5
|
|
|
|
|
|
2018-03-17 17:47:51 +00:00
|
|
|
define Device/tplink_tl-wr902ac-v3
|
|
|
|
|
$(Device/tplink)
|
|
|
|
|
DTS := TL-WR902ACV3
|
|
|
|
|
IMAGE_SIZE := 7808k
|
|
|
|
|
DEVICE_TITLE := TP-Link TL-WR902AC v3
|
|
|
|
|
TPLINK_FLASHLAYOUT := 8Mmtk
|
|
|
|
|
TPLINK_HWID := 0x000dc88f
|
|
|
|
|
TPLINK_HWREV := 0x89
|
|
|
|
|
TPLINK_HWREVADD := 0x1
|
|
|
|
|
TPLINK_HVERSION := 3
|
2018-11-25 13:35:49 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt76x0e kmod-usb2 kmod-usb-ohci kmod-usb-ledtrig-usbport
|
2018-03-17 17:47:51 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += tplink_tl-wr902ac-v3
|
|
|
|
|
|
ramips: add support for UniElec U7628-01
UniElec U7628-01 is a router platform board based on MediaTek MT7628AN.
The device has the following specifications:
- MT7628AN (580MHz)
- 64/128/256 MB of RAM (DDR2)
- 8/16 MB of flash (SPI NOR)
- 5x 10/100 Mbps Ethernet (MT7628 built-in switch)
- 1x 2T2R 2.4 GHz Wi-Fi (MT7628)
- 1x miniPCIe slot (with PCIe and USB 2.0 buses)
- 1x miniSIM slot
- 1x microSD slot
- 1x USB 2.0 port
- 7x single-color LEDs (GPIO-controlled)
- 1x bi-color LED (green GPIO-controlled, red -> LED_WLAN# in miniPCIe)
- 1x reset button
- 1x UART header (4-pins)
- 1x SDXC/GPIO header (10-pins, connected with microSD slot)
- 1x DC jack for main power (12 V)
The following has been tested and is working:
- Ethernet switch
- miniPCIe slot (tested with modem and Wi-Fi card)
- miniSIM slot
- sysupgrade
- reset button
- USB 2.0 port*
Due to a missing driver (MMC over GPIO) this is not supported:
- microSD card reader
* Warning:
USB buses in miniPCIe and regular A-type socket are connected together,
without any proper analog switch or USB HUB.
Installation:
This board might come with a different firmware versions (MediaTek SDK,
PandoraBox, Padavan, etc.). If your board comes with PandoraBox, you can
install LEDE using sysupgrade. Just SSH to the router and perform forced
sysupgrade (due to a board name mismatch). The default IP of this board
should be: 192.168.1.1 and username/password: root/admin. In case of a
different firmware, you can use web based recovery described below.
Use the following command to perform the sysupgrade (for the 128MB
RAM/16MB flash version):
sysupgrade -n -F lede-ramips-mt76x8-u7628-01-128M-16M-squashfs-sysupgrade.bin
Recovery:
This board contains a Chinese, closed-source bootloader called Breed
(Boot and Recovery Environment for Embedded Devices). Breed supports web
recovery and to enter it, you keep the reset button pressed for around
5 seconds during boot. Your machine will be assigned an IP through DHCP
and the router will use IP address 192.168.1.1. The recovery website is
in Chinese, but is easy to use. Click on the second item in the list to
access the recovery page, then the second item on the next page is where
you select the firmware. In order to start the recovery, you click the
button at the bottom.
SDXC/GPIO header (J3):
1. SDXC_D3 / I2C_SCLK
2. SDXC_D2 / I2C_SD
3. SDXC_D1 / I2S_DI
4. SDXC_D0 / I2S_WS
5. SDXC_CMD / I2S_CLK
6. SDXC_CLK / GPIO0
7. SDXC_CD / UART_RXD1
8. UART_TXD1
9. 3V3
10. GND
Other notes:
1. The board is available with different amounts of RAM and flash. We
have only added support for the 128/16 MB configuration, as that seems
to be the default. However, all the required infrastructure is in place
for making support for the other configurations easy.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
2017-11-03 20:12:49 +00:00
|
|
|
define Device/u7628-01-128M-16M
|
|
|
|
|
DTS := U7628-01-128M-16M
|
|
|
|
|
IMAGE_SIZE := 16064k
|
|
|
|
|
DEVICE_TITLE := UniElec U7628-01 (128M RAM/16M flash)
|
|
|
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ohci kmod-usb-ledtrig-usbport
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += u7628-01-128M-16M
|
|
|
|
|
|
2017-01-08 06:30:10 +00:00
|
|
|
define Device/vocore2
|
|
|
|
|
DTS := VOCORE2
|
|
|
|
|
IMAGE_SIZE := $(ralink_default_fw_size_16M)
|
|
|
|
|
DEVICE_TITLE := VoCore VoCore2
|
|
|
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ohci kmod-usb-ledtrig-usbport \
|
2017-03-03 06:07:34 +00:00
|
|
|
kmod-sdhci-mt7620
|
2017-01-08 06:30:10 +00:00
|
|
|
endef
|
2017-12-10 22:45:20 +00:00
|
|
|
TARGET_DEVICES += vocore2
|
2017-01-08 06:30:10 +00:00
|
|
|
|
2017-08-26 01:49:45 +00:00
|
|
|
define Device/vocore2lite
|
|
|
|
|
DTS := VOCORE2LITE
|
2016-05-11 10:21:45 +00:00
|
|
|
IMAGE_SIZE := $(ralink_default_fw_size_16M)
|
2017-08-26 01:49:45 +00:00
|
|
|
DEVICE_TITLE := VoCore VoCore2-Lite
|
|
|
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ohci kmod-usb-ledtrig-usbport \
|
|
|
|
|
kmod-sdhci-mt7620
|
2016-09-08 22:57:31 +00:00
|
|
|
endef
|
2017-12-10 22:45:20 +00:00
|
|
|
TARGET_DEVICES += vocore2lite
|
2017-01-28 16:05:56 +00:00
|
|
|
|
2018-10-22 15:21:16 +00:00
|
|
|
define Device/wavlink_wl-wn570ha1
|
|
|
|
|
DTS := WL-WN570HA1
|
|
|
|
|
IMAGE_SIZE := $(ralink_default_fw_size_8M)
|
|
|
|
|
DEVICE_TITLE := Wavlink WL-WN570HA1
|
|
|
|
|
DEVICE_PACKAGES := kmod-mt76x0e
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += wavlink_wl-wn570ha1
|
|
|
|
|
|
2019-02-17 12:21:42 +00:00
|
|
|
define Device/wavlink_wl-wn575a3
|
|
|
|
|
DTS := WL-WN575A3
|
|
|
|
|
IMAGE_SIZE := $(ralink_default_fw_size_8M)
|
|
|
|
|
DEVICE_TITLE := Wavlink WL-WN575A3
|
|
|
|
|
DEVICE_PACKAGES := kmod-mt76x2
|
|
|
|
|
SUPPORTED_DEVICES += wl-wn575a3
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += wavlink_wl-wn575a3
|
|
|
|
|
|
2017-01-28 16:05:56 +00:00
|
|
|
define Device/wcr-1166ds
|
|
|
|
|
DTS := WCR-1166DS
|
|
|
|
|
BUFFALO_TAG_PLATFORM := MTK
|
|
|
|
|
BUFFALO_TAG_VERSION := 9.99
|
|
|
|
|
BUFFALO_TAG_MINOR := 9.99
|
|
|
|
|
IMAGES += factory.bin
|
|
|
|
|
IMAGE/sysupgrade.bin := trx | pad-rootfs | append-metadata
|
|
|
|
|
IMAGE/factory.bin := \
|
|
|
|
|
trx -M 0x746f435c | pad-rootfs | append-metadata | \
|
|
|
|
|
buffalo-enc WCR-1166DS $$(BUFFALO_TAG_VERSION) -l | \
|
|
|
|
|
buffalo-tag-dhp WCR-1166DS JP JP | buffalo-enc-tag -l | \
|
|
|
|
|
buffalo-dhp-image
|
|
|
|
|
DEVICE_TITLE := Buffalo WCR-1166DS
|
2018-11-30 10:10:29 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt76x2
|
2017-01-28 16:05:56 +00:00
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += wcr-1166ds
|
2017-08-26 01:49:45 +00:00
|
|
|
|
2018-01-17 07:14:41 +00:00
|
|
|
define Device/widora_neo-16m
|
|
|
|
|
DTS := WIDORA-NEO-16M
|
2017-08-26 01:49:45 +00:00
|
|
|
IMAGE_SIZE := $(ralink_default_fw_size_16M)
|
2018-01-17 07:14:41 +00:00
|
|
|
DEVICE_TITLE := Widora-NEO (16M)
|
2017-08-26 01:49:45 +00:00
|
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ohci
|
2018-01-17 07:14:41 +00:00
|
|
|
SUPPORTED_DEVICES += widora-neo
|
2017-08-26 01:49:45 +00:00
|
|
|
endef
|
2018-01-17 07:14:41 +00:00
|
|
|
TARGET_DEVICES += widora_neo-16m
|
2017-08-26 01:49:45 +00:00
|
|
|
|
2018-01-08 05:27:28 +00:00
|
|
|
define Device/widora_neo-32m
|
|
|
|
|
DTS := WIDORA-NEO-32M
|
|
|
|
|
IMAGE_SIZE := $(ralink_default_fw_size_32M)
|
|
|
|
|
DEVICE_TITLE := Widora-NEO (32M)
|
|
|
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ohci
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += widora_neo-32m
|
|
|
|
|
|
2019-01-11 23:37:43 +00:00
|
|
|
define Device/wiznet_wizfi630s
|
|
|
|
|
DTS := WIZFI630S
|
|
|
|
|
IMAGE_SIZE := $(ralink_default_fw_size_32M)
|
|
|
|
|
DEVICE_TITLE := WIZnet WizFi630S
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += wiznet_wizfi630s
|
|
|
|
|
|
2017-08-26 01:49:45 +00:00
|
|
|
define Device/wrtnode2p
|
|
|
|
|
DTS := WRTNODE2P
|
|
|
|
|
IMAGE_SIZE := $(ralink_default_fw_size_16M)
|
|
|
|
|
DEVICE_TITLE := WRTnode 2P
|
|
|
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ohci kmod-usb-ledtrig-usbport
|
|
|
|
|
endef
|
2017-12-10 22:45:20 +00:00
|
|
|
TARGET_DEVICES += wrtnode2p
|
2017-08-26 01:49:45 +00:00
|
|
|
|
|
|
|
|
define Device/wrtnode2r
|
|
|
|
|
DTS := WRTNODE2R
|
|
|
|
|
IMAGE_SIZE := $(ralink_default_fw_size_16M)
|
|
|
|
|
DEVICE_TITLE := WRTnode 2R
|
|
|
|
|
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ohci
|
|
|
|
|
endef
|
2017-12-10 22:45:20 +00:00
|
|
|
TARGET_DEVICES += wrtnode2r
|
2018-01-23 01:46:36 +00:00
|
|
|
|
2018-01-24 00:27:51 +00:00
|
|
|
define Device/zbtlink_zbt-we1226
|
2018-01-23 01:46:36 +00:00
|
|
|
DTS := ZBT-WE1226
|
|
|
|
|
IMAGE_SIZE := $(ralink_default_fw_size_8M)
|
|
|
|
|
DEVICE_TITLE := ZBTlink ZBT-WE1226
|
|
|
|
|
endef
|
2018-01-24 00:27:51 +00:00
|
|
|
TARGET_DEVICES += zbtlink_zbt-we1226
|
2018-04-08 14:04:11 +00:00
|
|
|
|
|
|
|
|
define Device/zyxel_keenetic-extra-ii
|
|
|
|
|
DTS := ki_rb
|
|
|
|
|
IMAGE_SIZE := 14912k
|
|
|
|
|
BLOCKSIZE := 64k
|
|
|
|
|
DEVICE_TITLE := ZyXEL Keenetic Extra II
|
2018-11-30 10:10:29 +00:00
|
|
|
DEVICE_PACKAGES := kmod-mt76x2 kmod-usb2 kmod-usb-ohci kmod-usb-ledtrig-usbport
|
2018-04-08 14:04:11 +00:00
|
|
|
IMAGES += factory.bin
|
2018-11-29 09:48:03 +00:00
|
|
|
IMAGE/factory.bin := $$(sysupgrade_bin) | pad-to $$$$(BLOCKSIZE) | \
|
2018-04-08 14:04:11 +00:00
|
|
|
check-size $$$$(IMAGE_SIZE) | zyimage -d 6162 -v "ZyXEL Keenetic Extra II"
|
|
|
|
|
endef
|
|
|
|
|
TARGET_DEVICES += zyxel_keenetic-extra-ii
|
