broadcom-wl driver bound to ssb device with ssb driver probe
have osh handle struct pdev pointer value initialized with
ssb_device pointer. Later on pdev is used with legacy pci
dma api as pci_dev thus causing oops sometimes.
The patch replaces legacy pci dma api and pass relevant
device struct pointer to avoid crashes.
Signed-off-by: George Kashperko <george@znau.edu.ua>
SVN-Revision: 26949
the attached patch makes ipcalc.sh accept IP/Netmask combinations in
CIDR notation. Before you could only do:
# sh ipcalc.sh 192.168.0.0 255.255.255.0 1 10
IP=192.168.0.0
NETMASK=255.255.255.0
BROADCAST=192.168.0.255
NETWORK=192.168.0.0
PREFIX=24
START=192.168.0.1
END=192.168.0.11
with this patch you can also execute it with:
sh ipcalc.sh 192.168.0.0/24 1 10
IP=192.168.0.0
NETMASK=255.255.255.0
BROADCAST=192.168.0.255
NETWORK=192.168.0.0
PREFIX=24
START=192.168.0.1
END=192.168.0.11
The patch is based on #1260 [1], i just changed one line to calculate
the START end END ips right. I wonder why that never got included. If
there is no reason not to do i would like to ask you to commit that
patch, because its a functionality i (and probably others) miss quite often.
Btw, i also fixed 4 useless tabs, that might look a bit strange in the
patch.
Regards, Manuel
SVN-Revision: 26930
Since the oldest kernel in trunk is 2.6.30 the modules always use the
newer names, so we can just use the _generic prefix directly.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 26903
There's only 2.6, so it doesn't make sense to mention modules that are
2.4 only or for modules that they are available only for 2.6.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 26902
With no 2.4 support in trunk, we can safely remove any 2.4 definitions for
kmods and merge the 2.6 definitions into the generic ones.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 26901
Since there's only 2.6 in trunk $(KMOD_SUFFIX) can be safely replaced with
ko for all mainline kernel modules.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 26900
Note that the Alix6 uses GPIO 27 to disable wireless transmit (W_DIS#), whereas on all other versions this is used to actuate the speaker.
GPIO 1 : SIM select (Alix6)
GPIO 6 : LED1
GPIO 25 : LED2
GPIO 27 : LED3 or RFKILL (Alix6)
GPIO 24 : Soft switch 1
No kernel version bump. Added i2c-scx200-acb for lm-sensors support.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
SVN-Revision: 26880
Note that the Alix6 uses GPIO 27 to disable wireless transmit (W_DIS#), whereas on all other versions this is used to actuate the speaker.
GPIO 1 : SIM select (Alix6)
GPIO 6 : LED1
GPIO 25 : LED2
GPIO 27 : LED3 or RFKILL (Alix6)
GPIO 24 : Soft switch 1
No kernel version bump. Added i2c-scx200-acb for lm-sensors support.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
SVN-Revision: 26879
Add the required board definition, default config and image generation for
the T-Home Speedport W 303V Typ B.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 26878
Add two helpers for generating correctly tagged images for the T-Home
Speedport W 303V Typ B as well as xor'd ones as required by CFE.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 26877
Rename the DSL-274xB rev C2's board ID to "AW4139" to match the one used
for the rev C3 (same hardware) and add a fixup for C2. Also generate
images for C3.
While we are at it, rename the LEDs to conform to the Linux LED naming
conventions.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 26876
Make the fixup board ID independent from the image name to allow using
the same board ID for similar devices.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 26874
This patch adds 802.1Q VLAN support for the ADM6996M chip.
The driver is loaded for both the FC and M model. It will detect which of the
two chips is connected. The FC model is initialised, but no further
functionality is offered.
The PHY driver will always report "100 Mbit/s, link up", for both the M and FC
models. This reflects the fact that the link between switch chip and Ethernet
MAC is always on[1].
Further documentation can be found in the kernel's
Documentation/networking/adm6996.txt
Signed-of-By: Peter Lebbing <peter@digitalbrains.com>
SVN-Revision: 26865
Florian Fainelli
Felix Fietkau
Daniel Dickinson
Hamish Guthrie
Jo-Philipp Wich
Matteo Croce
John Crispin
Hauke Mehrtens
Vasilis Tsiligiannis