This stabilizes USB support. The old patch was handling initialization
in a different order that was causing some problems with few USB 3.0
devices. Some weren't detected, some were working unstable, sometimes
USB 3.0 could hang the whole controller.
A still known issue (but not a regression) is controller hang triggered
by connecting USB 1.1 device when not having OHCI controller enabled
(kmod-usb-ohci).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45997
On bcm53xx we still need usb-ohci to support USB 1.1 devices and it
obviously needs bcma-hcd.ko that will init controller and register
platform device.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 45994
This one cannot possibly work, as it depends on cfg80211, which is built
out of tree.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 45985
Besides source.tgz, 001-elfutils-portability.patch (provided by upstream
project) where updated.
Other patches where updated to fix hulk warnings and minor conflicts.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
SVN-Revision: 45984
Currently "make clean" only clears the build_dir/target*, but leaves
staging_dir/target* intact. "make clean" should also clean the
staging_dir/target* directories, as in the current situation some old
packages or libraries may be linked into the firmware from staging_dir
despite a "make clean".
The patch reorganises clean / dirclean functionality so that
* "make clean" also clears the staging_dir/target* in addition to
build_dir/target*.
* "make dirclean" clears toolchain and host(=tools) directories from both
build_dir and staging_dir
signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
SVN-Revision: 45973
AR8337 supports a configuration bit to swap MAC0 and MAC6.
Currently this is set in general if an AR8337 is detected and causes
issues with devices using an AR8334 (internally an AR8337, just
less chip pins).
And it might even cause issues with AR8337-based devices with
different board designs.
Swapping the MAC's however isn't needed for AR8337 in general.
It's just needed in case of certain board designs (affected devices
seem to be based on Atheros reference board AP135/136-010).
Therefore this configuration bit should be moved to platform data.
The patch includes the needed changes to the device initialization
code of affected devices. Hopefully I didn't miss any ..
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 45970
elfutils is required by perf. So we'll move this package from
packages.git and make it part of the core distribution.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45969
bzip2 is required by elfutils, itself required by perf. So we'll move
this package from packages.git and make it part of the core
distribution.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45968
argp-standalone is required by elfutils, itself required by perf. So
we'll move this package from packages.git and make it part of the core
distribution.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 45967
Hello,
I found out that in some rare cases grep can treat Makefile as a binary file. That happened to me on UTF-8 Gentoo if Makefile contained a character which was from extended ASCII table.
Without this patch the output of the grep command in the $(FILELIST) target is not valid (contains line "Binary file matches") and following commands fail to create feed index file.
Best Regards,
Martin Strbacka
Signed-off-by: Martin Strbacka <martin.strbacka@nic.cz>
SVN-Revision: 45966
This patch adds the pll_1000 value for eth0 interface. This makes the Rocket M
XW image compatible with other Ubiquiti devices with similar hardware with a
Gigabit Ethernet port.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
SVN-Revision: 45965
The *u-boot-initramfs* images are not ITB/FIT images but are rather
supposed to be loaded to RAM and jumped-into.
To avoid confusion, change the file extension from itb to bin.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 45963
This is for security precautions. As persist_tun and persist_key are
already there, this should not cause compatibility issue.
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
SVN-Revision: 45961
In new firmware-4.bin (for ath10k) mac offset is 0x114 (276), not 0x118 (280).
This also closes#19751, bug introduced in #45624
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
SVN-Revision: 45958
The mynet range extender hardware is suffering from ethernet
link loss when booting with a recent openwrt image. This only
happens on 100mbps links, with 1Gbps speed the link was fine.
The cause of the problem is that the AR8035 PHY (aka F1E)
requires turning on and off the special TX delay setting
depending on the speed of the link.
The 10mbps mode only needed the proper pll value, which was
extracted from the vendor code.
Reported-by: Pascal Paradis
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
SVN-Revision: 45954
- fix iconv detection because it adds host paths
- disable python detection (host python-config is found)
iconv issue is reported by buildbot config.log + replicated locally
see config.log in logs.tar.gz
python issue observed locally on Arch Linux
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 45953
Adds PPP unnumbered support via the parameter unnumbered which points to a logical OpenWRT interface.
The PPP proto shell handler will "borrow" an IP address from the unnumbered interface (if multiple
IP addresses are present the longest prefix different from 32 will be "borrowed") for which a host
interface dependency will be created. Due to the host interface dependency the PPP unnumbered interface
will only "borrow" an IP address from an interface which is up.
The borrowed IP address will be shared as local IP address by the PPP daemon and no other local IP
will be accepted from the peer in the IPCP negotiation.
A typical use case is the usage of a public IP subnet on the Lan interface which will be shared
by the PPP interface as local IP address.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
SVN-Revision: 45948
When r42245 moved A4001N to DT based detection the image padding size
was accidentally increased from 4 to 8 MiB. This made images unflashable
on these devices.
Fixes#19836.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45945
Felix Fietkau
Matteo Croce
Steven Barth
Rafał Miłecki
Jonas Gorski
Imre Kaloz