Add full support for TP-Link RE450.
The wireless SoC is similiar to Archer C7: QCA9558 + QCA9880 (pci).
The ethernet interface is AR8035, but the mdio is connected to the gpio and
the chipset builtin mdio bus isn't used, which is unique (and weird), so the
kernel gpio mdio module is used.
The two ethernet leds are connected to the GPIO, so they are both configured,
one to indicate link status and the other to indicate data transfer.
The generation of the image was added to the image Makefile.
The return value of tplink-safeloader is not ignored anymore (to fail on error)
The result factory image is flashable from the stock web ui.
Signed-off-by: Tal Keren <kooolk@gmail.com>
[rd@radekdostal.com: ar71xx: RE450: do not build RE450 for nand]
Signed-off-by: Radek Dostál <rd@radekdostal.com>
[hyniu@o2.pl: ar71xx: RE450: Renaming LED accordance with the standard]
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
[jo@mein.io: squash fixes from Radek and Henryk into original commit]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The firmware image that is used in TP-Link RE450 (and some more devices from
the RE series) is tplink-safeloader.
In the kernel partition, the kernel is compressed in a regular tp-link
firmware that is just used for booting. Since it is only used for compressing
and booting, only four fields are filled in the header:
Vendor, version, kernel load address and kernel entry point.
mktplinkfw-kernel is a simpler version of mktpolinkfw that generate such
images. It also specifies the hardware id (as it is in the product info
section), so when doing a sysupgrade - the existing code will check for
hardware compatibility.
Signed-off-by: Tal Keren <kooolk@gmail.com>
[rd@radekdostal.com: add build target to .../image/tp-link.mk]
Signed-off-by: Radek Dostál <rd@radekdostal.com>
mktplinkfw ignores -j in combined mode, the EOF marker is added by
tplink-safeloader.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
In the latest version of grub-mkimage, the prefix option is mandatory.
Not supplying it fails with:
```
Prefix not specified (use the -p option).
```
In grub-2.02-beta2 a DEFAULT_DIRECTORY was defined
in `include/grub/osdep/hostfile_unix.h` as:
```
#if defined (__NetBSD__)
/* NetBSD uses /boot for its boot block. */
# define DEFAULT_DIRECTORY "/"GRUB_DIR_NAME
#else
# define DEFAULT_DIRECTORY "/"GRUB_BOOT_DIR_NAME"/"GRUB_DIR_NAME
#endif
```
Where:
* GRUB_BOOT_DIR_NAME == boot
* GRUB_DIR_NAME == grub
This was used if the -p option was omitted.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
This patch is part of a series adding support for 0x9200 and 0x9300. The
prior was merged into the upstream kernel while the latter was not due
to lack of testers. Drop the patch as it is untested and most likely
unused.
Signed-off-by: John Crispin <john@phrozen.org>
When running sysupgrade for the first time over the second partition
(that still had stock firmware) the rootfs wasn't flashed as there
wasn't enough space.
This happend because stock also uses UBI, but the volume name wasn't
recognised and wasn't deleted before flashing.
Signed-off-by: Adrian Panella <ianchi74@outlook.com>
The si3210 is a SLIC device providing a complete analog telephone
interface and therefore frequently used in soho router.
The si3210 have a native spi interface to be controlled by the CPU
but currently there is no dedicated driver in lede.
Adding a registration for this device in spidev allow to control the
device in user space.
This way of patching is also in line with the rationale of the spidev
driver, see: http://marc.info/?t=148145791900001&r=1&w=2
The si3210 has been also added in the DWR-512 DT to properly describe
the HW.
Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
While researching for the armvirt target, I looked at the
existing arm platforms. It turns out that the mediatek target
with its sole MT7623N/A chip is sold as a "highly integrated
multimedia network router system-on-chip". To that end, it
lists support for the "NEON multimedia processing engine with
SIMDv2 / VFPv4 ISA support".
<http://topics.mediatek.com/en/products/connectivity/wifi/home-network/wifi-ap/mt7623na/>
So this patch enables the CPU_SUBTYPE to use this information.
This should have the nice side effect that LEDE's phase2 builders
no longer need to built a separate "cortex-a7" target, so this
should free up some resources.
Cc: John Crispin <john@phrozen.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Bump & refresh patches for all 4.4 targets.
Compile & run tested: ar71xx Archer C7 v2
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Fix the mtd partition layout and enable both radios in the dts
Tested-by Andrius Štikonas <andrius@stikonas.eu>
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
The TL-WR842N v2 has the following switch port layout with swconfig port 0
being connected to eth1:
Power LAN4 LAN3 LAN2 LAN1 WAN USB
(*) | [...] | [...] | [...] | [...] | [...] | [.]
swconfig port: 1 4 3 2 n/a
netdev: eth1 eth1 eth1 eth1 eth0
Adjust the board defaults to match this model specific layout.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The imagetag RSA signature field may not exceed 20 characters, so trim the
Git hash portion from the REVISION variable in order to ensure that the
resulting string fits within this field.
The current revision values may be longer than 20 chars, especially when
building within a dirty tree. In this case, the revision will look like
"r2435+75-b4aa3c8" which, combined with the "LEDE-" prefix, is 21 chars long.
Fixes the following error spotted by the buildbots:
Error: RSA Signature (rsa_signature,r) too long.
make[4]: *** [.../lede-brcm63xx-generic-NEUFBOX6-squashfs-cfe.bin] Error 1
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This patch add the 3G modem DWM-158 to the usb-serial option driver.
The DWM-158 is a pcie 3G modem. It is embedded in the DWR-512 modem
supportet by lede. The patch has been submitted and merged in the upstream
linux-next repository.
Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
This patch adds supports for the WNR2000v1 board with 4MB flash, and
produces device-specific factory, rootfs, and sysupgrade files for the
WNR2000v1. This board is errorneously claimed as supported on the OpenWRT
wiki as AP81, but AP81 image would not work because of APT81 image
requiring having 8MB of flash, while WNR2000v1 has only 4MB.
The image requires the u-boot bootloader to be modified to fuhry's
bootloader first.
Short specification:
- CPU: Atheros AR9132
- 4x 10/100 Mbps Ethernet, 1x WAN 10/100 Mbps
- 4 MB of Flash
- 32 MB of RAM
- UART header (J1) on board
- 1x button
Factory/Initial flash instructions:
- Set up a TFTP server on your local machine.
- Download the uImage for ar71xx-generic and the rootfs image for
ar71xx-generic-wnr2000 and save in the tftp server root.
- Gain serial access to the router via the UART port (telnetenable over
the network only won't work!).
- Upgrade the u-boot bootloader to fuhry's version by running the
script: http://fuhry.com/b/wnr2000/install-repart.sh
- When the router restarts, interrupt u-boot and gain access to u-boot command line.
- Repartititon the board and flash initial uImage and rootfs as follow.
Commands to type in u-boot:
# tells u-boot that we have a tftp server on 192.168.1.10
setenv serverip 192.168.1.10
# tells u-boot that the router should take the address 192.168.1.1
setenv ipaddr 192.168.1.1
# erase the region from 0x050000-0x3f0000
erase 0xbf050000 +0x3A0000
# loads sqfs.bin on TFTP server, and put it to memory address 0x81000000
tftpboot 0x81000000 sqfs.bin
# it will tell you the length of sqfs.bin in hex, let's say ZZZZZZ
# copy bit by bit 0xZZZZZZ bytes from offset 0x050000
cp.b 0x81000000 0xbf050000 0xZZZZZZ
# same to the uImage.bin, write it right next to sqfs.bin
# again, 0xYYYYYY is the length that tftpboot reports
tftpboot 0x81000000 uImage.bin
cp.b 0x81000000 0xbf2a0000 0xYYYYYY
# We need to tell the kernel what board it is booting into, and where to find the partitions
setenv bootargs "board=WNR2000 console=ttyS0,115200 mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,3712k(firmware),64k(art)ro rootfstype=squashfs,jffs2 noinitrd"
# Tell u-boot where to find the uImage
setenv bootcmd "bootm 0xbf2a0000"
# Tell u-boot to save parameters to the u-boot-env partitions
saveenv
# Reset the board
reset
Tested on:
- WNR2000v1 board.
- Initial flash works.
Known bugs:
- I don't know why factory image doesn't work on initial flash on stock
firmware in u-boot recovery mode while it should.
- Sysupgrade does not yet work, if you do -f it will mess up your
installation (requiring a reinstall of sqfs and uImage).
Signed-off-by: Huan Truong <htruong@tnhh.net>
The xt_id match was used by the firewall3 package to track its own rules but
the approach has been changed to use xt_comment instead now, so we can drop
this nonstandard extension.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
These patches were queued for 4.10. For possible use cases see added:
[PATCH] ubifs: Use dirty_writeback_interval value for wbuf timer
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This also makes the detection more flexible, as it doesn't need to check
for each model explicitly.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
This board is very old and unlikely to still be relevant today. Support
for it contains a significant amount of device specific baggage which is
worth getting rid of.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
There are many targets using user space scripts to generate firmware but
bcm53xx doesn't need this, so let's disable that kernel option.
This lets us avoid some scary-looking kernel warnings like:
brcmfmac 0001:04:00.0: Falling back to user helper
firmware brcm!brcmfmac43602-pcie.txt: firmware_loading_store: map pages failed
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
/etc/preinit has been the default init-script for a very long time (at
least since Linux 2.6.30 in OpenWrt). Remove the kernel command line
"init" parameter to get rid of duplicate and inconsistent definitions
of this parameter (some boards, like FRITZ3370 for example did not use
it at all, while it's just copy and paste on others).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Use devicetree's /chosen/stdout-path instead of the kernel command line
(embedded in the .dts-files) to specify the serial console. Using the
chosen node is recommended on devicetree based platforms.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
YunCore SR3200 is a dual-band AC1200 router, based on Qualcomm/Atheros
QCA9563+QCA9882+QCA8337N.
YunCore XD3200 (FCC ID: 2ADUG-XD3200) is a dual-band AC1200 ceiling mount
AP with PoE support, based on Qualcomm/Atheros QCA9563+QCA9882+QCA8334.
Common specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 128 MB or RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2T2R 2.4 GHz, with ext. PA (SKY65174-21), up to 30 dBm
- 2T2R 5 GHz, with ext. PA (SKY85405-11) and LNA (SKY85601-11), up to 30 dBm
SR3200 specification:
- 5x 10/100/1000 Mbps Ethernet
- 6x ext. RP-SMA antennas (actually, only 4 are connected with radio chips)
- 3x LED (+ 5x LED in RJ45 sockets), 1x button
- UART header on PCB
XD3200 specification:
- 2x 10/100/1000 Mbps Ethernet, with 802.3at PoE support (WAN port)
- 4x internal antennas
- 3 sets of LEDs on external PCB (+ 2x LED near RJ45 sockets), 1x button
- UART and JTAG (custom 6-pin, 2 mm pitch) headers on PCB
LED for 5 GHz WLAN is currently not supported on both devices as it is
connected directly to the QCA9882 radio chip.
Flash instruction under vendor firmware, using telnet/SSH:
1. If your firmware does not have root password, go to point 5
2. Connect PC with 192.168.1.x address to LAN or WAN port
3. Power up device, enter failsafe mode with button (no LED indicator!)
4. Change root password and reboot (mount_root, passwd ..., reboot -f)
5. Upload lede-ar71xx-...-sysupgrade.bin to /tmp using SCP
6. Connect PC with 192.168.188.x address to LAN port, SSH to 192.168.188.253
7. Invoke:
- cd /tmp
- fw_setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000"
- mtd -e firmware -r write lede-ar71xx-...-sysupgrade.bin firmware
Flash instruction under U-Boot, using UART:
1. tftp 0x80060000 lede-ar71xx-...-sysupgrade.bin
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000"
5. saveenv && reset
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Add support for NXP layerscape ls1046ardb 64b/32b Dev board.
LS1046ARDB Specification:
-------------------------
Memory subsystem:
* 8GByte DDR4 SDRAM (64bit bus)
* 512 Mbyte NAND flash
* Two 64 Mbyte high-speed SPI flash
* SD connector to interface with the SD memory card
* On-board 4G eMMC
Ethernet:
* Two XFI 10G ports
* Two SGMII ports
* Two RGMII ports
PCIe:
* PCIe1 (SerDes2 Lane0) to miniPCIe slot
* PCIe2 (SerDes2 Lane1) to x2 PCIe slot
* PCIe3 (SerDes2 Lane2) to x4 PCIe slot
* USB 3.0: one super speed USB 3.0 type A port, one Micro-AB port
* UART: supports two UARTs up to 115200 bps for console
Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
This attribute is not evaluated any more and the boot loader on these
reference boards does not provide a broken root= or console= parameter.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add an extra function to patch the mac and fixup the checksum
afterwards. Calculate the checksum position automatically. The offset
to the mac address is the same for all checksum protected EEPROMs.
No EEPROM requires a byte swapped mac address. The mac byte swap code
was required due to an bug in the script that is now fixed.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The EEPROM data in the flash of the ARV7518PW, ARV8539PW22,
BTHOMEHUBV2B and BTHOMEHUBV3A is stored byte-swapped (swab16), meaning
that for example the ath9k base_eep_header fields "version" (high and
low byte), "opCapFlags" and "eepMisc" are swapped (the latter ones are
just 1 byte wide, thus their position is swapped).
The old "ath,eep-endian" property enabled the corresponding swapping
logic in the ath9k driver (swab16 in ath9k_hw_nvram_swap_data, which is
based on the magic bytes in the EEPROM data which have nothing to do
with the calibration data - thus this logic should not be used
anymore).
Since we have switched to the upstream ath9k devicetree bindings there
is no binding anymore which enables swab16 in ath9k (as this logic is
not recommended anymore as explained above), leading to ath9k
initialization errors:
ath: phy0: Bad EEPROM VER 0x0001 or REV 0x00e0
(this shows that the version field is swapped, expected values are VER
0x000E and REV 0x0001)
Swapping the ath9k calibration data when extracting it from the flash
fixes the devices listed above (all other devices do not require
additional swapping, since the position of the fields is already as
expected by ath9k). This allows ath9k to read the version correctly
again, as well as the more important "eepmisc" field (which is used for
determining whether the data inside the EEPROM is Big or Little Endian
which is required to parse the EEPROM contents correctly).
Fixes: a20616863d ("lantiq: use ath9k device tree bindings
binding/owl-loader")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Rob suggested I should use of_machine_is_compatible insteak of a new
property and updated patch has been sent.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This is helpful for Orion-based NAS boxes that have the XOR engine enabled
since it provides faster software RAID.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The harddisk target is for NAS boxes, so set the DEVICE_TYPE accordingly so we
get a sensible default package selection.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Enable support for this machine in the kernel and also produce valid image
files with the correct machine id.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Needed to work around ethernet hang issues on Ubiquiti NanoStation Loco XW,
because ar71xx is not converted to device tree yet.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
By default, forwarding between all ports is allowed on init. This is
problematic in cases where some ports are supposed to be isolated from
each other, most commonly LAN/WAN separation.
REG_ESW_PORT_PCR(port) has a destination mask for a particular port,
controlling what other ports it is allowed to send packets to.
Instead of initializing all to 0xff (all ports), allow each physical
port to send to the CPU port, and the CPU port to send to all other
ports.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This fixes the partition name for the firmware splitter, the cfi
address and adds the mtd-eeprom address for wmac. It adds additional
LEDs and make use of them in diag.sh and 01_leds.
Please note that the ":blue:wired" LED is used because the
":blue:router" behaviour is unpredictable for failsafe indication. The
issue with the router LED is that you have two states only.
"off" is steady on and "on" blinks. Therefore the wired LED is more
suitable.
Furthermore it reuses the correct switch configuration definition to
reflect the device ports and numbering. Additionally fixes the issue
that the default configuration is not applied as no port 6 exists on
this device.
Signed-off-by: Tobias Wolf <github-NTEO@vplace.de>
sysupgrade command fails due to missing U-Boot environment-processing
binaries on sysupgrade ramdisk. The missing binaries result in the
following output:
Switching to ramdisk...
Performing system upgrade...
ash: /usr/sbin/fw_printenv: not found
ash: fw_setenv: not found
ash: touch: not found
cannot find target partition
Signed-off-by: Vignesh Balasubramaniam <vigneshb.hp@gmail.com>
The name from the Device define will be used in the metadata. Due to
typo/different spelling, this name might not match the one exported in
/lib/mvebu.sh.
Signed-off-by: Mathias Kresin <dev@kresin.me>
use pwr LED in diag.sh
Expose unused pinmux pins as GPIOs
export power LED and buzzer pins
Use rb750gr3:blue:pwr LED in diag.sh for boot status instead of rb750gr3:green:usr
Signed-off-by: Andrew Yong <me@ndoo.sg>
Imported from https://source.codeaurora.org/quic/qsdk/system/openwrt/commit/?h=korg/linux-3.4.y/release/arugula_bb_cs&id=2be4f8a8b205ae1a37db44839864451ebe893e6e
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
Enable flow control of LAN and WAN ports to
get better performance.
Setup pvid as 0 for all ports during initialisation
to avoid confusion during system or switch INIT.
Disable PORT MAC before config MAC to avoid it work abnormal.
This change is for IR-054144, IR-057315.
Change-Id: I345f3dffa59ad3f97150e09692723da12a7b1067
Signed-off-by: Zou Shunxiang <shunxian@codeaurora.org>
Signed-off-by: xiaofeis <xiaofeis@codeaurora.org>
Imported from e1aaf7ec00%5E%21/#F0
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
CHROMIUM: net: ar8216: address security vulnerabilities in swconfig & ar8216
This patch does the following changes:
*address the security vulnerabilities in both swconfig framework and in
ar8216 driver (many bound check additions, and turned swconfig structure
signed element into unsigned when applicable)
*address a couple of whitespaces and indendation issues
BUG=chrome-os-partner:33096
TEST=none
Change-Id: I94ea78fcce8c1932cc584d1508c6e3b5dfb93ce9
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
Reviewed-on: https://chromium-review.googlesource.com/236490
Reviewed-by: Toshi Kikuchi <toshik@chromium.org>
Commit-Queue: Toshi Kikuchi <toshik@chromium.org>
Tested-by: Toshi Kikuchi <toshik@chromium.org>
Import from fd7b89dd46%5E%21/#F0
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
CHROMIUM: drivers: ar8216: prevent device duplication in ar8xxx_dev_list
If probe is called twice, once for PHY0 and a second time for PHY4,
the same switch device will be added twice to ar8xxx_dev_list, while
supposedly this list should have one element per hardware switch present
in the system.
While no negative impact have been observed, it does happen if a
platform instanciates these two PHYs from device-tree, as an example.
Change-Id: Iddcbdf7d4adacb0af01975b73f8e56b4582e894e
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
Reviewed-on: https://chromium-review.googlesource.com/234790
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Toshi Kikuchi <toshik@chromium.org>
Tested-by: Toshi Kikuchi <toshik@chromium.org>
Import from c3fd96a7b8%5E%21/#F0
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
CHROMIUM: drivers: ar8216: hold ar8xxx_dev_list_lock during use_count--
It is possible for the remove() callback to run twice in parallel, which
could result into --use_count returning only 1 in both cases and the
rest of the unregistration path to never be reached.
This case has never been observed in practice, but we will fix
preventively to make the code more robust.
BUG=chrome-os-partner:33096
TEST=none
Change-Id: If09abe27fdb2037f514f8674418bafaab3cbdef6
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
Reviewed-on: https://chromium-review.googlesource.com/232870
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Toshi Kikuchi <toshik@chromium.org>
Tested-by: Toshi Kikuchi <toshik@chromium.org>
Import from c05af20272
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
CHROMIUM: drivers: ar8216: sync mib_work cancellation
ar8xxx_mib_stop() is called from ar8xxx_phy_remove(), so we want to make
sure the work doesn't run after priv is freed / the device ceases to
exist.
BUG=chrome-os-partner:33096
TEST=none
Change-Id: Iafb44ce93a87433adc4576e5fea5fda58d1f43a9
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
Reviewed-on: https://chromium-review.googlesource.com/232827
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Toshi Kikuchi <toshik@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Tested-by: Toshi Kikuchi <toshik@chromium.org>
RPM clock controller driver had made its way upstream and previous
approach of directly redoing a driver to support ipq806x is a no go anymore.
Thus reverting mentioned patches to upstream state and renaming
in correct patch numbering accordance.
To make the driver work on ipq806x boards we introduce a custom patch.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
The SDK Makefile still trys to copy the docs folder which was removed
with 882f4d2d63. This causes an SDK build
error.
All other removals are just cleanup.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Refresh patches on all 4.4 supported platforms.
077-0005-bgmac-stop-clearing-DMA-receive-control-register-rig.patch
removed as now upstream.
Compile & run tested: ar71xx - Archer C7 v2
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
ifxhcd never had roothub support but since kernel 3.x it was expected
that a roothub always exists.
The patched fixed a null pointer deref in the usb subsystem because of
the missing roothub.
Since ifxhcd is gone, this whole patch isn't required any longer.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This way the on nand bad block table is preserved and used. Add support
for nand OOB ECC checksums as well. It should fix all reported ubi
errors, which were all related to bad nand blocks and a purged on nand
bad block table.
The existing ubi partition will be reused, which eliminates the need
to touch the caldata during initial install. The BT u-boot has support
for loading a kernel from an ubi volume. It isn't necessary any longer
to replace the BT u-boot with a custom compiled one to use LEDE.
It is required to restore the BT Firmware and install LEDE from scratch
to switch to the new partition layout.
An image for restoring the BT firmware and installing LEDE is provided
at https://github.com/mkresin/lede/releases.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Backport upstream commit a61ae81a1907af1987ad4c77300508327bc48b23.
The actually purpose of the patch was to do some cleanup. As a side
effect of this cleanup, the device node is now passed to nand_dt_init.
This allows to use the common nand device tree properties
- nand-bus-width
- nand-on-flash-bbt
- nand-ecc-mode
- nand-ecc-step-size
- nand-ecc-strength
for the plat_nand driver.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Due to the addition of the bindings to the ath9k driver, this code
isn't used any longer. The fixup is now done by the owloader.
Rename the ath_eep.c file to ath5k_eep.c to indicate that this files
includes ath5k related code only.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This moves the extraction of the eeprom/calibration data to a hotplug
firmware script. Additionally it modifies all .dts to configure ath9k
directly from within the .dts.
The owl-loader approach enables support on devices with exotic eeprom
data locations (such as unaligned positions on the flash or data
inside an UBI volume).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
[add ath9k caldata mac address patcher]
[fixes DGN3500 wifi mac]
[fixes BTHOMEHUBV3A wifi mac]
[set invalid mac for BTHOMEHUB2B, FRITZ3370, FRITZ7320 & FRITZ7360SL to restore previous random mac behavior]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Remove all comments in ubnt_xm_board_detect(), as it's not possible to add
comments to specific lines of the case construct anyways.
Fixes: 9a5801e7 "ar71xx: add model detection for UBNT Rocket Ti"
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
This adds support for the Intel Falcon SoC for GPON.
Support for the Falcon SoC was removed in commit c821836395 svn rev:
40392 from OpenWrt, this commit adds it again.
This patch adds a new subtarget for the Falcon SoC, but it still misses
all the drivers needed to control the GPON part.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The DEVICE_PACKAGES are not included in the initramfs image in case
TARGET_PER_DEVICE_ROOTFS is set. This might produces initramfs images
with a not working network configuration because of a missing swconfig.
Workaround the issues by adding the essential swconfig package to the
default packages selection and deselect swconfig for boards not having
swconfig included before via device packages.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Remove the wifi5g LED from the the d7800, r7500 and r7800. Albeit this
GPIO is mentioned in the GPL tarball, it doesn't do anything. The
2.4/5 GHz LEDs are connected to the wifi chips and not be controlled
from the the userspace.
Use the LEDs names/colours as they are used in the board manuals. Merge
redundant LED configurations. Use the phy[0|1]tpt trigger for the
wireless LEDs. Remove the workarounds for the not controllable wireless
LEDs.
Fix spi compatible strings and remove superfluous spi-max-frequency
parameters.
If there are two power leds, use one for indicating normal operation and
one for failsafe/upgrade. Keep the on/off state of the main power led
during boot.
Use the usb pinmux settings from the nbg6817 gpl sources.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Set the pinmux to the values found in the GPL tarballs of the boards.
Remove pinmux which are is not used (like nand pinmux for spi
flash boards).
This allows to use the wan orange led of the C2600 which had a wrong
pinmux before. Might fix buttons or leds of other boards as well.
Fix the LED color and the ledswitch key code of the C2600. Rename the
ledgnr to ledswitch.
Add support for indication the boot state using LEDs to the D7800,
NBG6817, R7500 and R7500v2.
Change GPIO active to readable values in D7800, EA8500, R7500,
R7500v2 and R7800.
Change gpioexport to gpio pinmux.
Add proper "drive strenght" to i2c4_pins and use it for RPM on
C2600, D7800, EA8500, R7500, R7500v2.
Remove pcie pinmux from D7800.
Move pinctrl to correct place in NBG6817 and R7800.
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
This allows specifying PCI devices as children of the PCIe controller
node to pass configuration data to them.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Fix bug that LEDE failed to boot with this message:
WARNING: CPU: 2 PID: 1 at drivers/spi/spi-mt7621.c:214
mt7621_spi_transfer_one_message+0x28c/0x620()
Signed-off-by: Yong-hyu, Ban <perillamint@gentoo.moe>
Use gpio.h definition of GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW. Remove unused backup partition to increase available JFFS space. As long as U-Boot env variable "bootcount" is < 3 (reset to 0 after boot by init script) SamKnow's U-Boot will not attempt to boot from the backup flash address (0xe30000).
Signed-off-by: Andrew Yong <me@ndoo.sg>
This device uses NAND FLASH, so it should be kept in nand subtarget.
Also, inlcude in packages kmod-usb-ledtrig-usbport instead of
obsolete kmod-ledtrig-usbdev.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This router is similar to the C2600. Ethernet on WAN + LAN, switch,
sysupgrade, LEDs, buttons and WiFi on 2G + 5G do work. The xDSL modem
and the POTS/DECT interface are not supported yet.
It is not possible to flash LEDE via the TP-Link webinterface. The
image need to be signed. The first 0x200 bytes of the image is the
TP-Link header including the signature. The signature is not validated
by the bootloader. The LEDE image is zeroed in this area.
To install LEDE it is necessary to solder a four pin header to JP2.
Connect a serial interface to this header and interrupt the autostart
of kernel. Transfer the sysupgrade image via TFTP and write it to the
serial flash at 0x320000.
Signed-off-by: Sebastian Quilitz <zeraphim@x-pantion.de>
CONFIG_CRYPTO_DEV_SUN4I_SS was previously set to y but did not take
effect because of the absence of CONFIG_CRYPTO_HW=y
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Currently, the device-tree partition is marked as read-only.
Hence, userspace tools like mtd can't write into the partition.
This however will be necessary in case the DTB needs to be
updated.
This patch also adds the kernel.dtb image, so the compiled
DTB is exported as a file and available in the binary
directory along the firmware images.
Note: the u-boot does expects the dtb to be a uimage.
To update the dtb manually:
1. copy the generated dtb to the router.
2. mtd erase /dev/mtd2
3. mtd write wndr4700.dtb /dev/mtd2
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Unlike x86, kvm for arm has to be built into the kernel. The kernel
config was prepared with the following command
make kernel_menuconfig CONFIG_TARGET=platform
Then enable ARM_LPAE, VIRTUALIZATION, KVM in that order
Other config changes are done by the build system. The following text
tries to explain some of them, for archive purposes probably...
- BUILD_BIN2C. It was dropped probably because the prompt is empty and
no other config option selects it. bin2c is a host executable for
converting binary content to a piece of c code for inclusion
- CRYPTO_DEV_SUN4I_SS. It was dropped because the dependency CRYPTO_HW
was not enabled. Setting that aside, packaging it as a loadbable
module in lieu of other sunxi specific modules seems more appropriate
- PGTABLE_LEVELS. It was changed from 2 to 3 because 3 is the default
when ARM_LPAE is enabled
- HAVE_KERNEL_GZIP, etc.. These are enabled in generic config
- SCHED_INFO, ZLIB_INFLATE. These were dropped probably for the same
reason as for BUILD_BIN2C
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
The Dlink DWR-512-B modem is a ralink 5350 processor based embedding
a 3G mini-pcie router.
The oem JBOOT bootloader has to be replaced by a RT5350 SDK
U-Boot such as https://github.com/stevenylai/ralink_sdk - U-Boot
configured for the RT5350 256MiB SDR.
Main reason to change the bootloader is the encrypted header used to
store the kernel image. In this way an image can only be generated
using the propietary binboy tool (included in the GPL distribution
from Dlink). The binboy tool doesn't allow to modify the kernel/rootfs
partition scheme. This is considered a big constraint (limited kernel
size and inefficient usage of flash space).
For interested people I pubblished the details of my investigation
about the encrypted firmware header here:
http://lists.infradead.org/pipermail/lede-dev/2016-October/003435.html
Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
Fix a typo in mt7621.dtsi compatible string. Disable spi, sdhci and pci
in mt7621.dtsi and enable the nodes in the indiviual board dts files.
The nodes require further device specific configuration anyway.
Remove the m25p80@0 spi child node from mt7621.dtsi and add the
chunked-io parameter to the individual board dts files. Fix the spi
flash compatible string for the WNDR3700V5.
Drop the mt7621-eval-board compatible string for all boards which are
not the eval board.
Drop the linux,modalias parameter from spi flash node.
Remove the xhci node from board files, it is already enabled in dtsi.
Disable xhci for boards not having usb ports populated.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Fix configuration files for the Livebox 1 routers.
- Add status led
- Set eth0 as the LAN port, for coherence with RedBoot and comfortability.
- Add led triggers
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Fix Image generation for the Livebox 1
- missing "relocate-kernel", wrong "LOADADDR", fix it
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Fix the DTS file for the Livebox 1 routers:
- part probe wrong, it should be RedBoot (uppercase matters)
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Fix the DTS file for the Livebox 1 routers:
- leds are totally wrong, fix them.
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Fix the DTS file for the Livebox 1 routers:
- no failsafe button, use button 1 for this purpose
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
fix in sdhci Use ralink_soc == MT762X_SOC_MT7621AT instead of CONFIG_SOC_MT7621 which is
wrong and breaks builds on mt7620a-similar platforms (MT7621, MT7688)
Signed-off-by: Andrew Yong <me@ndoo.sg>
Enable work-arounds present in the code commented-out but needed to write to
sdcard on mt7621 which currently causes kernel to oops when engaging in
serious writing to sdcard. With this change applied, there are still
occasional warnings thrown by the mmc driver, however, at least it no longer
crashes the system and even large writes (full-card dump/erase/write/compare)
don't show any corruption.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Rebase to LEDE and added "CONFIG_SOC_MT7621" check to ensure non-MT7621 devices do not face performance regressions.
Signed-off-by: Andrew Yong <me@ndoo.sg>
This adds the patch submitted to upstream that adds BQL to the mvneta
driver: https://patchwork.kernel.org/patch/9328413/. Helps latency under
load when the physical link is saturated.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Parameters for dwc2 on lantiq.
A separate dwc2_core_params structure is defined for danube because danube
fifo sizes are large enough to be autodetected. This is not the case on
arx and vrx.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
Device tree binding for dwc2 usb driver on danube.
Leave old ifxhcd-danube driver as an alternative.
Also adds dr_mode = "host" to eliminate warning on boot.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
This patch adds support for the Cisco Meraki MX60/MX60W Security
Appliance. Flashing information can be found at
https://github.com/riptidewave93/LEDE-MX60
Specs are as follows:
AppliedMicro APM82181 SoC at 800MHz
1GiB NAND - Samsung K9K8G08U0D
512MB DDR RAM - 4x Nanya NT5TU128M8GE-AC
Atheros AR8327-BL1A Gigabit Ethernet Switch
1x USB 2.0 Port
More info can be found at https://wiki.openwrt.org/toh/meraki/mx60
Cc: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
This patch fixes the ethernet switch initial config for Mikrotik RB450 and RB450G.
The previous version wrongly changed the RouterStation Pro config. This one creates a specific config for the RB450G and leaves the RouterStation Pro unchanged.
Signed-off-by: João Chaínho <joaochainho@gmail.com>
CPE830 is a clone of AP90Q, with different type of antenna (panel)
and additional 4 LEDs for WiFi signal level indication.
Use the same flash approach as for YunCore AP90Q.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
YunCore AP90Q is an outdoor CPE/AP based on Qualcomm/Atheros QCA9531 v2.
Short specification:
- 650/600/216 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, passive PoE support
- 64/128 MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz with external PA, up to 29 dBm
- 2x internal 5 dBi omni antennas
- 4x LED, 1x button
- UART (JP1) header on PCB
Flash instruction under U-Boot, using UART:
1. tftp 0x80060000 lede-ar71xx-generic-ap90q-squashfs-sysupgrade
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9f050000"
5. saveenv && reset
Flash instruction under vendor fimrware, using telnet/SSH:
1. Connect PC with 192.168.1.x address to WAN port
2. Power up device, enter failsafe mode with button (no LED indicator!)
3. Change root password and reboot (mount_root, passwd ..., reboot -f)
4. Upload lede-ar71xx-generic-ap90q-squashfs-sysupgrade.bin to /tmp using SCP
5. Connect PC with 192.168.188.x address to LAN port, SSH to 192.168.188.253
6. Invoke:
- cd /tmp
- fw_setenv bootcmd "bootm 0x9f050000"
- mtd erase firmware
- mtd -r write lede-ar71xx-generic-ap90q-squashfs-sysupgrade.bin firmware
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
COMFAST CF-E380AC v1/v2 is a ceiling mount AP with PoE
support, based on Qualcomm/Atheros QCA9558+QCA9880+AR8035.
There are two versions of this model, with different RAM
and U-Boot mtd partition sizes:
- v1: 128 MB of RAM, 128 KB U-Boot image size
- v2: 256 MB of RAM, 256 KB U-Boot image size
Version number is available only inside vendor GUI,
hardware and markings are the same.
Short specification:
- 720/600/200 MHz (CPU/DDR/AHB)
- 1x 10/100/1000 Mbps Ethernet, with PoE support
- 128 or 256 MB of RAM (DDR2)
- 16 MB of FLASH
- 3T3R 2.4 GHz, with external PA (SE2576L), up to 28 dBm
- 3T3R 5 GHz, with external PA (SE5003L1), up to 30 dBm
- 6x internal antennas
- 1x RGB LED, 1x button
- UART (T11), LEDs/GPIO (J7) and USB (T12) headers on PCB
- external watchdog (Pericon Technology PT7A7514)
Flash instruction:
Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
As we already have support for CF-E316N v2 and many devices from
this vendor look similar, the support was included in existing
mach-*.c file, with few cleanups and fixes.
All 3 devices are based on Qualcomm/Atheros QCA9531 v2.
COMFAST CF-E320N v2 is a ceiling mount AP with PoE support.
Short specification:
- 650/393/216 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, both with PoE support
- 64 MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz, up to 22 dBm
- 2x internal antennas
- 1x RGB LED, 1x button
- UART (J1), GPIO (J9) and USB (J2) headers on PCB
- external watchdog (Pericon Technology PT7A7514)
COMFAST CF-E520N/CF-E530N are in-wall APs with USB and PoE support.
They seem to have different only the front panel.
Short specification:
- 650/393/216 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, WAN with PoE support
- 1x USB 2.0 (in CF-E520N covered by panel, available on PCB)
- 32 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz, up to 22 dBm
- 2x internal antennas
- 1x LED, 1x button
- UART (J1) headers on PCB
Flash instruction:
Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Update patch to remove pipetypes var declaration which was throwing
unused variable warning due to the original patch removing the only use.
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Fix the incorrect usage of ar934x_nfc_write_page and ar934x_nfc_write_page_raw.
Add *page* in the argument list and remove the local variable.
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
This fixes parsing partition placed after TRX with block-aligned length.
It's important e.g. for Archer C9 which has TRX with kernel only and
rootfs as separated partition.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Fix build on targets not using CONFIG_MODULE_STRIPPED.
Neither RTL8367_DRIVER_DESC nor RTL8367B_DRIVER_DESC are defined
anywhere. It worked for targets using CONFIG_MODULE_STRIPPED since our
module stripper no-ops the various module info macros.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Change grub's root device to xen/xvda,msdos1 for the x86_xen_domu
target so that it will boot without further changes.
Signed-off-by: Wilfried Klaebe <w+lede-project@chaos.in-kiel.de>
[Jo-Philipp Wich: fixed and rebased patch from FS#264, added subject]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Factory image can be installed via Zyxel WebUI.
Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
[removed linux,modalias parameter from flash node in dts]
[removed sdhci node from dts; no sd card slot here]
Signed-off-by: Mathias Kresin <dev@kresin.me>
This patch refreshes the ipq806x kernel patches.
There was a large PR for ipq806x in the queue when the kernel patches
were refreshed for 4.4.32, so currently there is quite much fuzz for
ipq806x.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
The Sitecom firmware upgrade file has SENAO_FIRMWARE_TYPE 2 set. This
looks rather wrong since SENAO_FIRMWARE_TYPE 2 is kernel only but the
file is way to big for only including a kernel.
The factory image need to have the dlf file extension. Otherwise the
Sitecom firmware rejects the file.
The stock firmware uses the following mac addresses:
LAN: 00:0C:F6:AA:BB:D8 (u-boot env: ethaddr)
2,4: 00:0C:F6:AA:BB:D8 (EEPROM)
5: 00:0C:F6:AA:BB:DC (EEPROM)
WAN: 00:0C:F6:AA:C8:43 (u-boot env: wanaddr)
Assuming the mac address range :D8 to :DC is reserved for this device,
the MAC addresses were reorder to have a unique MAC address for each
interface:
2.4GHz: 00:0C:F6:AA:BB:D8
LAN: 00:0C:F6:AA:BB:D9
WAN: 00:0C:F6:AA:BB:DA
5 GHz: 00:0C:F6:AA:BB:DC
The first MAC is assigned to the 2.4GHz WiFi interface
to keep compatibility with the SSIDs printed on the case, which have
the last three sextets of the MAC address appended.
There are still issues with the rt2x00 driver. It is not possible to
use both wireless interfaces at the same time. The 2.4 GHz
wireless (PCIe) only works if the internal 5GHz wireless is/has been
enabled or used for scanning. The internal 5GHz wireless only works if
the 2.4GHz wireless (PCIe) was never enabled. Disabling the 2.4Ghz
after it was enabled will result in stations seeing the 5Ghz AP but are
unable to connect.
Due to the not optimal working wifi the manufacture, backup and storage
partitions of the OEM firmware are kept for now to allow an easy switch
back to the Sitecom firmware.
Signed-off-by: Jasper Scholte <NightNL@outlook.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
This is a powerful API for parallel crypto from which many other modules
can benefit. It only winds up being turned on on SMP systems, which
means this adds 0 bytes to the kernel on tiny machines, while only
adding a small bit to SMP systems for big performance improvements.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Refresh patches for all targets that support kernel 4.4.
Compile-tested on all targets that use kernel 4.4 and aren't marked broken.
Runtime-tested on ar71xx, octeon.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Updating spi pins configuration in R7800 and C2600 DTs
Adding more usb power pin export and gsbi6 in R7800 DT
Updating and fixing leds
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
The patch #179 for RPM has initially been made for apq806x board. It has been modified to support ipq806x instead of apq8064.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
Adds Google's mirror as primary source and kernel.org as fallback.
Same as commit 0d4f02dfd6
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
In Device/ls1012ardb IMAGES variable, there are two separate firmware
references to the same packages, while do mult-job compile, the same package
build process will arise conflict occasionally. So, only reserve one ext4 fs
as the default firmware.bin.
Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
OpenMesh devices have often LEDs which are not yet used by OpenWrt. These
should still be available as disabled LEDs in the system configuration for
easier modification.
Signed-off-by: Jaylin Yu <jaylin.yu@open-mesh.com>
[sven.eckelmann@open-mesh.com: Remove LEDs already specified via diag.sh,
add wifi/status LEDs]
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
MMC support has been added to x86-64 a while ago, there is no reason not
to support it in x86-generic as well.
Signed-off-by: Andreas Ziegler <github@andreas-ziegler.de>
[Matthias Schiffer: add commit message]
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
PATA support has been removed from x86-generic without any note in LEDE
r538. Not including them makes the generated images incompatible with older
(and some newer) hardware without any significant gain.
Add it back, and also add the same drivers (as far as available) to x86-64.
Signed-off-by: Andreas Ziegler <github@andreas-ziegler.de>
[Matthias Schiffer: add back x86-generic, update commit message]
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Polling every 40ms causes more than 10% CPU load on weak devices. An
interval of 200ms is much more reasonable.
Signed-off-by: Martin Weinelt <martin@darmstadt.freifunk.net>
[Matthias Schiffer: adapt OpenWrt patch; add ramips; extend commit message]
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Without setting the HSR to the selected channel, the WLAN of the UAP
Outdoor+ will exhibit high packet loss in RX.
Based-on-patch-by: Stefan Rompf <stefan@loplof.de>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
The marvell,88e6352 and marvell,88e6172 compatible strings are used in
target/linux/generic/files/drivers/net/phy/mvsw61xx.c. No idea why grep
missed them when I searched for them.
Thanks to Syrone Wong for noticing and reporting my mistake.
Signed-off-by: Mathias Kresin <dev@kresin.me>
All compiled device tree files not mentioned are binary identical to the
former ones.
Fix the obvious decimal/hex confusion for the power key of ramips/M2M.dts.
Due to the include of the input binding header, the BTN_* node names in:
- ramips/GL-MT300A.dts
- ramips/GL-MT300N.dts
- ramips/GL-MT750.dts
- ramips/Timecloud.dts
will be changed by the compiler to the numerical equivalent.
Move the binding include of lantiq boards to the file where they are
used the first time to hint the user where the values do come from.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Fixes invalid device tree parameters.
Drop the mvsw61xx node used in mvebu device tree source files. It looks
like some kind of ethernet switch cargo cult. Neither the
marvell,88e6352 nor the marvell,88e6172 compatible strings can be found
in any LEDE file or in the kernel sources.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This special dwc2 device definition for the Netgear WNDR4700
has been replaced by amcc,usb-otg-405ex.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch moves the common SoC device tree entries
from the currently four supported platforms into a
common apm82181.dtsi.
Furthermore, this patch also changes the GPIO, IRQ and
input definitions of the supported platforms to use the
defined dt-bindings macros for GPIO_ACTIVE_LOW|HIGH,
KEY_WPS|RESTART|*, IRQ_TYPE_* when it's appropriate.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch adds support for the amcc,usb-otg-405ex device
which is found in all APM82181 SoCs.
Note: The system can't use the generic "snps,dwc2" compatible
because of the special ahbcfg configuration. The default
GAHBCFG_HBSTLEN_INCR4 of snps,dwc2 can cause a system hang
when the USB and SATA is used concurrently.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
As specified by e0229a16b0 if the VR9
based router provides FXS ports and they should enabled then the
following must added to the kernel command line:
mem=[TOTALMEMSIZE-2M] vpe1_load_addr=ADDRESS vpe1_mem=2M
By adding mem= parameter a pci device stop working correctly. The
pci-lantiq.c module use get_num_physpages() to compute dynamically the
memory amount of the board.
The mem= make the module to compute in the wrong way the BAR11MASK, so
in this situation the mask is misaligned with the dma area that the
hardware expects.
This patch is a port of what legacy ifxmips_pci.c does.
Signed-off-by: Eddi De Pieri <eddi@depieri.net>
The latest stock firmwares for US and EU regions have started checking the
region code.
Tested-by: Andreas Ziegler <ml@andreas-ziegler.de>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Some builders have troubles cloning the boot-wrapper-aarch64.git repository so
provide a mirror checksum to allow downloading from sources.lede-project.org
instead.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Assign an unused MAC addresses to the 2.4GHz wifi interface as it was
originally planed but not possible.
The MAC address numbering of the TEW-691GR changes to the following
pattern:
LAN: AA:BB:CC:DD:EE:0C
WIFI: AA:BB:CC:DD:EE:0D
WAN: AA:BB:CC:DD:EE:0F
The MAC address numbering of the TEW-692GR changes to the following
pattern:
LAN: AA:BB:CC:DD:EE:e4
WAN: AA:BB:CC:DD:EE:e5
2.4GHz: AA:BB:CC:DD:EE:e7
5 GHz: AA:BB:CC:DD:EE:e8
Set the label and compatible string for the TEW-692GR PCIe wireless
according to the the PCI binding documentation.
Use the wifi@0,0 label and the pci0,0 compatible string since the PCI
vendor and device id is unknown. It should work anyway since the
compatible string isn't evaluated (yet).
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use the ralink,mtd-eeprom instead of invoking the userspace firmware
loader.
Set the label and compatible string according to the the PCI binding
documentation.
Use the wifi@0,0 label and the pci0,0 compatible string in case the
PCI vendor and device id is unknown. It should work anyway since the
compatible string isn't evaluated (yet).
This commit might fixes the PCIe wireless for the Buffalo WHR-600D.
This board was mentioned in the board 10-rt2x00-eeprom firmware hotplug
script but never had the correct eeprom name set to trigger the
firmware from flash extraction.
Use the usual eeprom for the soc wmac of the Dovado Tiny AC.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Set a device specific wireless mac address for ARV7506PW11, VGV7519 and
VGV7510KW22. The one from the EEPROM is a generic one and the same on
all boards.
Use the wifi@0,0 label and the pci0,0 compatible string for the
ARV7519PW and ARV7525PW since the pci vendor and device id is unknown.
It should work anyway since the compatible string isn't evaluated
(yet).
Signed-off-by: Mathias Kresin <dev@kresin.me>
The patch 615-rt2x00-fix_20mhz_clk.patch fixes code introduced by
611-rt2x00-rf_vals-rt3352-xtal20.patch and makes the the platform data
property clk_is_20mhz obsolete.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Because the WAN port is handled by the internal AR8327N switch, the
device should use swconfig_leds trigger to handle the link activity
of the WAN LED. This has the added bonus that the WAN LED will now
go dark if there's no ethernet cable connected to the WAN port.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
It's supposed to significantly improve performance but doesn't seem to
affect Northstar unfortunately. It seems only some other platforms were
limited because of this DMA setup mistake.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The original repo in this Makefile disappeared from the internet so use another
copy of this repository on kernel.org. Also switch from git:// to https://
while being at it.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Port 1 registers the same IO resources as port 2 in the kernel resource
tree, which is wrong.
Fix this by using it's own resources as indicated in the overview
(cns3xxx.h).
Compiled & Tested on several GW2388-4 laguna boards which utilizes all 3
ports.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Since commit 484cb91 "sdk: bundle required firmware files" there is an
implicit dependency of the SDK on a prior Kernel compilation.
Change target/Makefile to make this dependency explicit to avoid race
conditions with parallel builds.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Switch to xz compression instead of using bz2.
This makes a considerable difference in size, ar71xx SDK from 60M to 35M.
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
- remove not existing properties
- remove properties having the same values as the included dtsi
- remove nodes which are disabled in the included dtsi and not enabled
in dts
- replace the deprecated pinctrl-* compatible strings
- use the same labels for nodes as the included dtsi
- move common used vr9 pci properties to vr9.dtsi
- remove the unused stp node from HomeHub 2B devcie tree source file
- fix spaces vs. tabs and remove superfluous linebreaks
Signed-off-by: Mathias Kresin <dev@kresin.me>
This fixes ondemand frequency scaling and moves ipq806x onto upstream driver
Also switching to ondemand frequency scaling as it is fixed now
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
The MikroTik hEX v3 (RB750Gr3) is a MT7621AT board which is similar to most MT7621 reference designs, it can be easily supported by this patch; however, the stock RouterBOOT bootloader has to be replaced by a MT7621 SDK U-Boot such as https://github.com/ndoo/RB750Gr3-U-Boot - U-Boot configured for the RB750Gr3 (16MiB SPI flash, 256MiB DDR3 RAM at 1200MHz).
RouterBOOT, the stock bootloader, does not initialize the UART and boots silently, making it preferable to replace it with a MT7621 SDK U-Boot with UART (57600 8N1) that supports HTTP, TFTP or serial upload of sysupgrade firmware and U-Boot.
Furthermore, RouterOS, the stock firmware, is contained in a proprietary modification of SquashFS without GPL sources; UART is also disabled in stock firmware.
The combination of LEDE firmware generated by this PR and MT7621 SDK U-Boot expects the printed MAC address to reside at offset `0xe000` of the factory partition (absolute offset is `0x4e000`); this is similar to the factory MAC address offset for several other MT7621 devices.
A 16MiB flash dump suitable for use with flashrom will be provided if/once this patch is accepted and binaries are built by LEDE buildbot. Alternatively, writing the U-Boot to the SPI flash starting at 0x0 offset and booting the board with serial console attached will allow TFTP, HTTP or serial upload of sysupgrade firmware.
Signed-off-by: Andrew Yong <me@ndoo.sg>
This patch bumps the 4.4 kernel from .28 to .30 and refreshes the patches.
Compile-tested on ar71xx, x86/64, ramips/mt7621, brcm47xx and kirkwood.
Run-tested on ar71xx & ramips/mt7621, brcm47xx and kirkwood (last two confirmed
by P. Wassi).
Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
This patch adds the kmod-usb3 and kmod-usb-ledtrig-usbport packages to the
DIR-860L B1 profile. The DIR-860L B1 has a USB 3 port.
Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
The QorIQ LS1012A processor, optimized for battery-backed or
USB-powered, integrates a single ARM Cortex-A53 core with a hardware
packet forwarding engine and high-speed interfaces to deliver
line-rate networking performance.
QorIQ LS1012A Reference Design System (LS1012ARDB) is a high-performance
development platform, with a complete debugging environment.
The LS1012ARDB board supports the QorIQ LS1012A processor and is
optimized to support the high-bandwidth DDR3L memory and
a full complement of high-speed SerDes ports.
LEDE/OPENWRT will auto strip executable program file while make. So we
need select CONFIG_NO_STRIP=y while make menuconfig to avoid the ppfe network
fiemware be destroyed, then run make to build ls1012ardb firmware.
The fsl-quadspi flash with jffs2 fs is unstable and arise some failed message.
This issue have noticed the IP owner for investigate, hope he can solve it
earlier. So the ls1012ardb now also provide a xx-firmware.ext4.bin as default
firmware, and the uboot bootcmd will run wrtboot_ext4rfs for "rootfstype=ext4"
bootargs.
Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
Add support for NXP layerscape ls1043ardb 64b/32b Dev board.
LS1043a is an SoC with 4x64-bit up to 1.6 GHz ARMv8 A53 cores.
ls1043ardb support features as: 2GB DDR4, 128MB NOR/512MB NAND, USB3.0, eSDHC,
I2C, GPIO, PCIe/Mini-PCIe, 6x1G/1x10G network port, etc.
64b/32b ls1043ardb target is using 4.4 kernel, and rcw/u-boot/fman images from
NXP QorIQ SDK release.
All of 4.4 kernel patches porting from SDK release or upstream.
QorIQ SDK ISOs can be downloaded from this location:
http://www.nxp.com/products/software-and-tools/run-time-software/linux-sdk/linux-sdk-for-qoriq-processors:SDKLINUX
Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
- setting read-only flag to important partitions
- enabling PA to improve 2.4 GHz signal strength
- add missing leds
- rename colour led
- add mac adress to 5GHz wlan interface
- included <dt-bindings/input/input.h> and <dt-bindings/gpio/gpio.h>
Signed-off-by: Henryk Heisig hyniu@o2.pl
(required not-distributable firmware blob - dump it by yourself from original firmware)
Signed-off-by: Eddi De Pieri <eddi@depieri.net>
(cherry picked from commit 064f467264c5c9b6eca0bb96b587f9412b770cc5)
Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
(required not-distributable firmware blob - dump it by yourself from original firmware)
Signed-off-by: Eddi De Pieri <eddi@depieri.net>
(cherry picked from commit eb0ce57270d0b5b81b224b9336cf54707497eede)
Modified after cherry-pick:
obj in Makefile
Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
Created minimal patchset based on BB rev 43158 by Eddi De Pieri
14.07/openwrt.git 79472c025449efae9310defad0d3a73cff14d756
If the VR9 based router provides FXS ports and they shoud enabled then
the following must added to the kernel command line:
mem=[TOTALMEMSIZE-2M] vpe1_load_addr=ADDRESS vpe1_mem=2M maxvpes=1
maxtcs=1
To use FXS 2M of RAM are needed for the VPE firmware. The size is set
by vpe1_mem.
The available RAM must be reduced by this size using the mem argument.
A correct load address (example 0x83e00000) for the firmware must be given,
too.
Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
(required not-distributable firmware blob - dump it by yourself from original firmware)
Signed-off-by: Eddi De Pieri <eddi@depieri.net>
(cherry picked from commit 8d924d43c0ea6839a3a33e54982e8da48b736001)
Modified after cherry-pick:
compatible attribute
Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
Build the RTC driver into the kernel, (and remove the optional module), in order
to make hctosys working. (Currently the module is loaded after hctosys has failed previously)
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Refresh patches for all targets that support kernel 4.4.
compile/run-tested on ar71xx, brcm47xx, kirkwood.
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Both the MR12 and MR16 are single gigabit ethernet devices, similar to the
MR18. This change gives them the correct network config on a fresh install.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
[Jo-Philipp Wich: adjust for alphabetical ordering, line wrap commit msg]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
In 814d70b2 the member mac06_exchange_en of struct
ar8327_pad_cfg was changed to mac06_exchange_dis,
but wpj344 was not adopted to stay in sync.
Signed-off-by: Christian Mehlis <christian@m3hlis.de>
Reported-by: Nick Dennis <ndennis@rapiduswireless.com>
Thanks to leaving .pattern file we can easily insert extra step between
linksys-pattern-partition and trx-v2-with-loader, e.g. rootfs one.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The old usbdev trigger never supported assigning more than 1 USB port.
This code we got was never working as expected and it was missing 2 more
ports. Switch to usbport to have LED working with all ports.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Tested-by: Christian Lamparter <chunkeey@gmail.com>
Fixes the same hctosys init issue as described in commit
5481ce9a11
The Gateworks Ventana family uses an emulated Dallas 1672
RTC device.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Support splitting WRGG images, found in some D-Link devices (e.g.
DAP-2695).
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: John Crispin <john@phrozen.org>
CPU: 2x1.8GHz ARM, RAM: 512MiB
Storage: 4MiB serial Flash, 3.9GiB MMC
NIC: 2x1GBit/s, Switch with 5 external and 2 internal ports
WiFi: Dualband, ath10k 2.4GHz, 5GHz MU-MIMO
For installation copy xx-mmcblk0p4-kernel.bin and xx-mmcblk0p5-rootfs-full.bin
to device. Then run:
cat xx-mmcblk0p4-kernel.bin > /dev/mmc0blk0p4
cat xx-mmcblk0p5-rootfs-full.bin > /dev/mmc0blk0p5
reboot -f
For debugging serial console is easily visible on board, no soldering needed.
Signed-off-by: André Valentin <avalentin@marcant.net>
This bugfix enables FXS support on dabube based devices.
Changed "compatible" attribute from "vmmc" to "vmmc-xway".
The vmmc driver uses "vmmc-xway".
Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
This patch adds support solely for version 1 of the TP-Link WR802N.
It is based on Rick Pannen's patch posted on the OpenWrt devel list.
Signed-off-by: Julius Schulz-Zander <julius@inet.tu-berlin.de>
Remove redundant code: merge boards/cases that share
the same network configuration.
Also fix the alphabetical ordering of the cases.
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
These boards do not have a switch, so they should have never been added
to this file in the first place.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
On the stock Meraki Firmare for the MR12/MR16, a chunk of SPI space
after u-boot-env is used to store the boards Mac address. Sadly as this
was removed on any device already on OpenWRT/LEDE, moving forward a new,
64k partition named "mac" will be used to store the mac address for the
device (which is the minimum size). This allows users to properly set
the correct MAC, without editing the ART partition (which holds the same
MAC for all devices).
The reason the space is taken from kernel instead of rootfs is currently
kernels are only 1.3MB, so that way we can leave the current rootfs
space alone for users who fully utilize the available storage space.
Once this partition is added to a device, you can set your MAC doing the
following:
mtd erase mac
echo -n -e '\x00\x18\x0a\x33\x44\x55' > /dev/mtd5
sync && reboot
Where 00:18:0a:33:44:55 is your MAC address.
This was tested, and confirmed working on both the MR12 and MR16.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
This moves the Meraki MR12 and Meraki MR16 to the new generic target.
Tested and verified working on both devices.
Note that kernel/rootfs images are still generated. This is because they
are used for the inital flashing process due to the fun pace at which
UBoot erases/writes to SPI.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Otherwise if we use ds1307 as kernel module, hctosys fails as ds1307 is
being initialized later then hctosys:
[ 2.427349] hctosys: unable to open rtc device (rtc0)
[ 3.714263] snvs_rtc 20cc000.snvs:snvs-rtc-lp: rtc core: registered 20cc000.snvs:snvs-r as rtc1
[ 8.990061] rtc-ds1307 3-006f: rtc core: registered mcp7941x as rtc0
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Build the RTC driver into the kernel, (and remove the optional module), in order
to make hctosys working. (Currently the module is loaded after hctosys has failed previously)
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
Refresh patches for all targets supporting 3.18 and not marked broken.
Compile-tested on all targets using 3.18 and not marked broken.
Changes to generic/610-netfilter_match_bypass_default_checks.patch based
on 84d489f64f.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Refresh patches for all targets supporting 4.1 and not marked broken.
Compile-tested on all targets using 4.1 and not marked broken.
Changes to generic/610-netfilter_match_bypass_default_checks.patch based
on 84d489f64f.
Changes to generic/666-Add-support-for-MAP-E-FMRs-mesh-mode.patch based
on a90ee92337.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Kernel 4.4 was ready for brcm47xx for almost a year now but I kept
postponing the bump due to problems with Linksys WRT300N v1.0. OpenWrt
and LEDE with 4.4 were hanging at the booting with the:
> Starting program at 0x80001000
(the last CFE message).
This was a permanent state, "make distclean" wasn't helping, I spent
hours debugging this and I was reliably reproducing the issue every
time. I also reported it on linux-mips ML in the thread:
> BCM4704 stopped booting with 4.4 (due to vmlinux size?)
After ~month I started working on WRT300N again. I got hangs as expected
every time I switched from 4.1 to 4.4. I started experimenting with:
1) TRX content (I tried dropping rootfs partition)
2) BZ_TEXT_START of lzma-loader
3) Flashing other variants of image: lzma compressed kernel (without a
loader), gzip compressed one, uncompressed one.
At some point I got rootfs-less image booting and after that I couldn't
reproduce problem anymore, even with a complete firmware. It seems like
hardware was in some locked/unstable state that got magically fixed.
I have LEDE working now, tested it even with "make distclean", it seems
we can bump kernel now. I'll keep testing it on WRT300N for some time.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Linksys WRT300N V1 has pretty bugged CFE bootloader (it crashes in a lot
of situations) that doesn't accept .bin image.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Refresh patches for all targets that support kernel 4.4.
compile/run-tested on brcm2708/bcm2710 only.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
When building packages within the SDK, there is no Git revision history
available so prepopulate SOURCE_DATE_EPOCH in version.mk, similar to
how we handle REVISION already.
Acked-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Read the temperature including the decimale place from the CGU_GPHY1_CR
register.
Decrement the temperature read from the register by 38.0 degree celsius.
The temperature range of the sensor is -38.0 to +154 °C and the register
value 0 is equal to -38.0 °C. This fixes the report of unrealistic
temperatures as seen on all tested boards.
Give the SoC a few milliseconds to get the first temperature value. On
some rare occasions there is no temperature value in the register when
read the first time after activation. This leads to a reported
temperature of -38.0 °C on boot.
Only version 1.2 of the vr9 SoC has a temperature sensor. Add a check
to make sure the driver doesn't load on v1.1 vr9 SoCs.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The device tree file of ARV752DPW uses numbers/hex values for gpio states and input event codes.
This cleans it up and uses the available macros from header files. This way the functions are easier to read and comprehend.
Signed-off-by: Andreas Eberlein <foodeas@aeberlein.de>
[sanitize all device tree files]
Signed-off-by: Mathias Kresin <dev@kresin.me>
The GPIO for reset switch is wrong in definition. Further the key codes for the two additional buttons are ineffective.
Both is fixed here.
Signed-off-by: Andreas Eberlein <foodeas@aeberlein.de>
Use the new image build code and remove the lzma loader. The lzma
loader was used to cheat the signature validation of the bootloader and
I found another way to do this.
To migrate boards already using LEDE/OpenWrt to the new image the
following steps need to be done once:
VR9 # run reset_uboot_config
VR9 # reset
VR9 # setenv ethaddr AA:BB:CC:DD:EE:FF
VR9 # setenv preboot ping 1.1.1.1\;bootm 0xb001f000
VR9 # saveenv
VR9 # tftp 0x81000000 lede-lantiq-xrx200-VG3503J-squashfs-sysupgrade.bin
VR9 # erase 0xb0020000 $(filesize)
VR9 # cp.b 0x81000000 0xb0020000 $(filesize)
The mac address is printed on the label at the bottom of the case.
The following steps are need to be done during first install:
VR9 # setenv preboot ping 1.1.1.1\;bootm 0xb001f000
VR9 # saveenv
VR9 # tftp 0x81000000 lede-lantiq-xrx200-VG3503J-squashfs-sysupgrade.bin
VR9 # erase 0xb0020000 $(filesize)
VR9 # cp.b 0x81000000 0xb0020000 $(filesize)
The image uses the uImage firmware splitter now instead of hardcoded
kernel and rootfs partitions. The firmware partition size was extended
to use flash space that was reserved for partitions required only by
the ECI firmware.
Due to the changes an upgrade to a later LEDE revision from a running
LEDE is supported now.
A default switch config was added and the device uses the same MAC
addresses as the ECI firmware now instead of the same for all VG3503J.
Signed-off-by: Mathias Kresin <dev@kresin.me>
We don't have any code for enabling it automatically yet but it allows
adding entries manually to the /etc/config/system.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This makes init.d script handle existing UCI entries using the new
trigger. It also switches all targets to use its package.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
There is no US firmware for the TL-WA901ND v4 yet, so we'll just
unconditionally set the EU region for now.
This makes LEDE flashable on these devices again. The format of the region
string is slightly different from the one used on the Archer C7 that is
generated by mktplinkfw (the second half of the region string is missing),
but it's similar enough to make it work.
Tested-by: Jannis Pinter <jannis@pinterjann.is>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
In dc92917 there was introduced login.sh wrapper which allows
configuration of console passwords via UCI system ttylogin config
option.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This patch adds support for the Airtight C-60.
SOC: Atheros AR9344 rev 2 (CPU:560.000MHz)
RAM: 128 MiB
NOR: MX25L3205D 4MiB
NAND: ST Micro NAND 32MiB 3,3V 8-bit
SW-NET: AR8327N (2 Ports)
WLAN1: Dual-Band AR9340 Rev:2 (built-in SoC)
WLAN2: Dual-Band AR9300 Rev:4 PCIe Chip
The switch is setup for an accesspoint:
LAN1: (gigabit) is the wan-port.
LAN2: (fast ethernet) is bridged with the br-lan.
Flashing Guide (via initramfs):
1. Connect a PC to the serial port of the C-60.
power up the C-60.
Enter u-boot command prompt:
#> nand erase
#> setenv bootcmd "bootm 0x9f060000"
#> saveenv
#> setenv ipaddr 192.168.1.1
#> setenv netmask 255.255.255.0
#> setenv serverip 192.168.1.100
#> setenv bootfile lede-ar71xx-nand-c-60-initramfs-kernel.bin
#> tftpboot
#> bootm
2. Wait for the C-60 to boot LEDE.
On the root prompt. Enter:
# ubiformat /dev/mtd4
# ubiattach -p /dev/mtd4
3. After that copy the sysupgrade.tar onto the router and run:
# sysupgrade sysupgrade.tar
to flash the image.
Special thanks to Chris Blake <chrisrblake93@gmail.com>. He provided
a C-60 unit and he helped with debugging the switch, LEDs and platfrom
support.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The commit "generic: ar8216: add sanity check to ar8216_probe"
(774da6c7a4) stated that PHY IDs
should be checked at address 0-4. However, the PHY 4 was
never check by the loop. This patch extends the check to be
similar to the Atheors SDK. It tries all 4 ports and skips
unconnected PHYs if necessary. If it cannot find any familiar
PHYs, it will prevent the phy driver from initializing.
This patch is necessary for the C-60. It doesn't have a
PHY at port 3, so this caused the check in ar8xxx_is_possible
to fail. As a result, the ethernet ports on the C-60 didn't
work.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The WBMR boards are the only ones in the whole tree selecting the wpad
and hostapd-utils package by default.
Remove the wps uci-default script as well, there is no obvious reason
why the wps config need to be set only for this board.
Signed-off-by: Mathias Kresin <dev@kresin.me>
All of the touched boards don't have an ethernet port. Allow to use the
wps button on these boards to enable the wireless radio after boot.
The force enabled wireless for the DCH-M225 is removed. It is reckless
to bring up an unencrypted wireless network by default these days.
Using the wps button to bring up the radio seam to me the better
approach.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Images installed via TFTP recovery or the Edimax webinterface of the
3g-6200n(l) are writting with the edimax header to flash.
Use only one image type for these boards. The migration to the
factory only images need to be done via TFTP recovery.
Use the same start address for the 3g-6200n(l) factory images as the
stock firmware images.
Thanks to Jan Dostrasil for reporting all the issues of the 3g-6200nl
and the patient testing of all changes.
Signed-off-by: Mathias Kresin <dev@kresin.me>
According to the author the code was added to in preparation for adding
support for a new board. The patch for the board was never send and the
code never really tested.
The edimax header starting with the edimax magic is put in front of the
uImage header. There is no special uImage header used. Means, default
magic and the type field is set to kernel as usual.
Signed-off-by: Mathias Kresin <dev@kresin.me>
edimax parser fix
The return value of the find_header function need to be added to the
uimage_size, otherwise mtd_find_rootfs_from() might search for a rootfs
within a custom header and fails.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Assign the reset functionality to the wps/reset buttons. Use the wlan
switch of the 6200n to enable/disable wlan.
Add the internet led of the 6200nl and use the led for boot status
indication
Signed-off-by: Mathias Kresin <dev@kresin.me>
With 3a9752bbd2 and later changes to
ramips_set_preinit_iface() the default vlan config applied during
preinit was changed. These changes were made without updating the
default network config to ensure that vlan interfaces used for lan/wan
are still configured.
Fix the issue by using the default all LAN portmap and disabling not
connected switch ports using portdisable device tree parameter.
Signed-off-by: Mathias Kresin <dev@kresin.me>
With de51026515 the explicit tagging of
the CPU port was removed. This leads to a not working default network
config, with vlans enabled but disabled CPU tagging, for boards where
all switch ports are having the same role.
In case the ports are having different roles set, tagging is is set
implicit for the CPU port by ucidef_add_switch().
Signed-off-by: Mathias Kresin <dev@kresin.me>
Don't set the lan/wan interface when using ucidef_add_switch. This
results into a wan interface albeit all ports a annotated as lan ports.
ucidef_add_switch takes care of setting the correct lan/wan interface
according to the annotation of the ports.
Signed-off-by: Mathias Kresin <dev@kresin.me>
COPYING is not present in $(LINUX_DIR) on imagebuilder and prevents a
successful image creation.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The patch "images: bump default rootfs size to 256 MB"
a1f83bad60 caused a crash
during boot for the recovery images. This is because
both variants of the MyBook Live only have 256MB of RAM
and for the recovery option, the ext4 rootfs was simply
stored in the RAMDISK.
This patch replaces recovery image for the MBL with an
initramfs kernel.
In order to boot the initramfs (for recovery or development):
0. copy the initramfs and device tree into tftp's server directory
# cp *-initramfs-kernel.bin to /tftp-server/mbl.bin
# cp *-ext4-kernel.dtb to /tftp-server/fdt.bin
1. Connect the MyBook Live (Duo) serial port.
(Warning! Use a 3.3v level shifter).
2. Hit Enter during u-boot and insert these three lines:
# setenv serverip 192.168.1.254; setenv ipaddr 192.168.1.1;
# tftp ${kernel_addr_r} mbl.bin; tftp ${fdt_addr_r} fdt.bin
# run addtty addmisc; bootm ${kernel_addr_r} - ${fdt_addr_r}
Where 192.168.1.254 is your TFTP server.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This will allow dynamically adding/removing at least virtio-net pci
devices which are quite the norm in cloud environment with QEMU/KVM
netdev_add bridge,id=wan2,br=br-wan,helper=/home/yousong/.usr/libexec/qemu-bridge-helper
device_add virtio-net-pci,id=devwan2,netdev=wan2,mac=11:22:33:22:11:00
The config was formed by selecting target x86/64 first, then select
CONFIG_HOTPLUG_PCI and CONFIG_HOTPLUG_PCI_ACPI with
make kernel_menuconfig CONFIG_TARGET=subtarget
The following text tries to explain how the current config was formed
1. CONFIG_PCI_LABEL and CONFIG_ATA_PIIX were removed because they were
already enabled in x86 platform config
2. CONFIG_ATA_SFF was removed because it was enabled in generic config
3. CONFIG_NLS was removed because it will be selected by CONFIG_PCI_LABEL
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
The D-Link DIR-869 A1 doesn't accept images with the jffs2 marker added
after the checksummed range, so we need to include it in the checksum and
fix it on first boot.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Split seama-factory and seama-sysupgrade into smaller pieces (similar to
the ramips code) to make the image generation more flexible.
Also use standard pad-offset instead of adding a block of zeros at the
beginning of the image that is later cut off again. Standard pad-rootfs can
be used as the seal header doesn't contain an image size or checksum.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
In case the adsl/vdsl service is disabled intentional, the output is
cluttered with the following message multiple times if the status of
the dsl line is queried:
killall: vdsl_cpe_control: no process killed
If the dsl line status is queried by LuCI, the logfile is spammed with
the message.
Fix the issue by using killall in quite mode. In quite mode killall
still returns a non-zero value if the to be killed process can not be
found so that existing logic based on the return value still works.
Signed-off-by: Mathias Kresin <dev@kresin.me>
TP-Link uses a different region coding mechanism for IL firmware for the Archer
C7 v2. Instead of of setting the region, they set a different TPLINK_HWREV.
Signed-off-by: Amir Rachum <amir@rachum.com>
Due to the introduced double whitespace the default package selection
isn't applied. This leads to errors like a not working networking
because of a missing swconfig binary.
Fixes FS#208.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Add USB led aliases to boards having an led which is meant to be used
as USB led according to the manuals.
Remove the kmod-ledtrig-usbdev from the default package selection for
boards not having an USB led. Add the kmod-ledtrig-usbdev to boards
where it is missing.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use a more generic name for the lantiq_get_dt_led_chosen function.
Drop the lantiq_is_dt_led_chosen function. The lantiq_get_dt_led
function can be used to achieve the same.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Convert the Zynq target to use the new image build code in order to fix
broken image generation after 9945a1dca5
changed the handling of CPIO images.
Also remove the misapplied ubifs feature flag since the image generation is
not using UBIFS for building FIT images.
As part of the conversion, move the DTB building and the uImage ramdisk
generation into separate build steps which can be generalized and shared
with other targets, like APM821xx, in the long run.
Also remove the legacy profile declarations and use new-style per-device
profiles which will allow different package sets per image in the future.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Add some missing symbols to the generic 4.1 kernel config which got triggered
by the introduction of the hda-intel sound module.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
applied bb-final-ramips-add-zyxel-nbg-419n2.patch from
123serge123, found at https://yadi.sk/d/1ZV0lKJwbTE65;
see https://forum.openwrt.org/viewtopic.php?pid=246905#p246905,
modified slightly to fit to CC release and to new lede build
system: image/rt305x.mk include file is used now
changed NBG-419N2.dts format to fit style of other dts files
Signed-off-by: Klaus <k-laus@quantentunnel.de>
This includes:
- use of local 'board' variable in LED names, wherever possible
- merge of boards with exactly the same LED configuration
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Keep everything in alphabetical order. Boards are ordered in two steps,
first within/inside common configuration (case section), then sections,
globally.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This includes:
- code style fixes
- removal of huge comment (it should be in doc, not here) and some small ones
- removal of redundant config for DR531/WPJ531 as the default is the same
- merge of boards with exactly the same interfaces config
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Convert etc/board.d/02_network in ar71xx target to the same shape
as we have in ramips target. Split code into two new functions:
- interface/s setup in ar71xx_setup_interfaces()
- MAC/s setup in ar71xx_setup_macs()
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
sysupgrade command fails due to missing U-Boot environment-processing binaries on sysupgrade ramdisk. The missing binaries result in the following output:
Switching to ramdisk...
Performing system upgrade...
ash: /usr/sbin/fw_printenv: not found
ash: fw_setenv: not found
ash: touch: not found
cannot find target partition
Fixes FS#197.
Signed-off-by: Aaron Curley <accwebs@gmail.com>
- CPU: MT7620A 580MHz
- Flash: 8MB - RAM: 64MB
- External PA+LNA on both WLAN2.4 and WLAN5
- 4x LAN ethernet and 1x WAN ethernet
Signed-off-by: Xuefu Lin <xuefulin@gmail.com>
It missed some changes needed for kernel 4.4. This is only used by the
Falcon SoC and not for the xRX SoCs.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Henryk Heisig
Vitaly Chekryzhev
Radek Dostál
Tal Keren
Matthias Schiffer
Alexandru Ardelean
Ludwig Thomeczek
John Crispin
Adrian Panella
Giuseppe Lippolis
Christian Lamparter
Kevin Darbyshire-Bryant
L. D. Pinney
Felix Fietkau
David Lutz
Yousong Zhou
Jo-Philipp Wich
Gad Krumholz
Huan Truong
Jing Lin
Rafał Miłecki
Martin Blumenstingl
Piotr Dymacz
Yutang Jiang
Hauke Mehrtens
Mathias Kresin
BangLang Huang
Álvaro Fernández Rojas
Florian Fainelli
Yong-hyu, Ban
Tobias Wolf
Tobias Wolf
Vignesh Balasubramaniam
Andrew Yong
dissent1
Pavel Kubelun
Sebastian Quilitz
Paul Wassi
Eddi De Pieri
Daniel Gonzalez Cabanelas
Toke Høiland-Jørgensen
Ben Mulvihill
Chris Blake
João Chaínho
Wilfried Klaebe
Hannu Nyman
Jasper Scholte
Dominik Menke
Jason A. Donenfeld
Stijn Tintel
dpeddi
Daniel Engberg
Koen Vandeputte
Jaylin Yu
FUKAUMI Naoki
Andreas Ziegler
Martin Weinelt
Roger Pueyo Centelles
Daniel Engberg
Sven Schwermer
Cezary Jackiewicz
Stijn Segers
Stefan Koch
Rosen Penev
Chris Blake
Christian Mehlis
Chuanhong Guo
André Valentin
Xuefu Lin
Julius Schulz-Zander
Petr Štetiar
Imre Kaloz
Andreas Eberlein
YuheiOKAWA
Karl Palsson
Florian Beier
Amir Rachum
Ben Whitten
Klaus
Aaron Curley