As explained in recent sysupgrade/nand.sh commits, current NAND
sysupgrade is a bit misleading because of nand_do_platform_check
behavior. It leaves a special mark in /tmp/sysupgrade-nand-path
triggering some diffent code path in nand_upgrade_stage1.
The plan is to have the check function only check the image and nothing
else. Then platform code (platform_pre_upgrade) should trigger NAND
specific upgrade path. This is what this patch implements.
Please note that because of current nand_upgrade_stage1 implementation
this patch doesn't change any behaior yet. It only prepares lantiq
target for changing nand_do_platform_check (it will be possible after
preparing all other targets as well).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 46939
Add AR9 DTS definition to be recognized by the DWC2 driver.
The same driver parameters can be mostly used except that some boards
seem to erroneously report OTG HNP/SRP capability of the USB HCD.
Forcing the HNP/SRP off allows these boards to work with the DWC2 as well.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
SVN-Revision: 46915
Since the AR9 USB is very similar to the VR9 USB it too can be used with
the upstream DWC2 driver.
Here are the DTS definitions which make it compatible with the DWC2
driver.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
SVN-Revision: 46914
Based on the ltq-hcd driver the AR9 USB can be initialized the same way
as the VR9 platform. Use the same initialization bits for both
platforms.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
SVN-Revision: 46913
Fixes support for AR9287 on TP-Link TD-W8980 and possibly other devices
which have an ath wifi chip at a PCI address other than 0xb8000000
(TD-W8980 for example has it's wifi chip at 0xbc000000).
Signed-off-by: Geoffrey McRae <geoff@spacevs.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 46869
Support for lantiq_svip_be has been removed a while ago, so EASY33016
images weren't buildable anymore. Remove the recipes as well as gzip
compressed kernel support, as EASY33016 was the last user of it.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46760
The BT Home Hub 5A uses three PEF7071 with PHY ID 0xd565a401. Daniel's
PHY driver (for his u-boot sources) already supports that PHY because
it uses a PHY ID mask of 0xfffffff8.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 46670
Instead of each target defining it the same, move the KDIR_TMP
definition to include/image.mk. In addition Image/Build/SysupgradeNAND
already requires KDIR_TMP to be set, so it makes sense to have it
globally defined.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46592
Variables dependend on JFFS2_BLOCKSIZE and NANDBLOCK_SIZE are used
for template generation, so need to be present before inclusion of
image.mk in target image Makefiles.
So move all declarations to before any includes.
Fixes: r42878 ("image.mk: clean up and parallelize mkfs calls")
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 46564
This ports 9e2a7b779e6f0914395da3657b00f0ac00209bfd to the 4.1 patches.
I forgot this when preparing the initial 4.1 patch.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 46453
Basically the only error I am seeing is "Correctable Error". Also newer
lantiq PCIe drivers have this message wrapped in a "if debug enabled"
block. So it should be safe to disable this warning.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 46222
Newer DSL driver versions depend on the address information.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 46221
Make it consistent with the net_device struct and the xrx200 driver
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 46219
All (still relevant) patches were refresh.
The following patches were dropped because they are applied upstream:
- 0003-MIPS-lantiq-handle-vmmc-memory-reservation.patch
- 0005-MIPS-lantiq-add-reset-controller-api-support.patch
- 0006-MIPS-lantiq-reboot-gphy-on-restart.patch
- 0009-MIPS-lantiq-command-line-work-around.patch
- 0010-MIPS-lantiq-export-soc-type.patch
- 0011-lantiq-add-support-for-xrx200-firmware-depending-on-.patch
- 0037-MIPS-lantiq-move-eiu-init-after-irq_domain-register.patch
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 46216
This also adds the old hardcoded value to the VGV7519BRN profile to make
sure that images are still generated correctly.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 45882
In r44391 the kernel partion size was increased to allow larger kernels,
but the rootfs partition offset was missed. Fix this by setting the
rootfs offset to the expected value.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 45868
There are already ifx_pcie_bios_{map_irq,plat_dev_init} hooks defined in
ifxmips_pcie.c. Instead of defining a new hook we simply re-use the
existing ones (this is basically what the lantiq BSP code does).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 45718
The PCIe bus seems to require a hack/workaround when PCI is enabled as
well. Unfortunately this is guarded by an CONFIG_IFX_PCI ifdef, which is
only defined in lantiq's BSP code. The config symbol for the upstream
lantiq PCI driver is CONFIG_PCI_LANTIQ.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 45717
Here the device tree entry for ifxhcd is listed as compatible with one
supported in dwc2 (after patching the dwc driver appropriately).
A second entry is added to support the second core of the hcd. This
entry is listed to be compatible with only dwc2. Done this way there
should be backwards support for both hcd drivers (ltq-hcd and dwc2)
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
SVN-Revision: 44676
This patch switches calls to readl/writel to their
dwc2_readl/dwc2_writel equivalents which preserve platform endianness.
This patch is necessary to access dwc2 registers correctly on big
endian systems such as the mips based SoCs made by Lantiq. Then dwc2
can be used to replace ifx-hcd driver for Lantiq platforms found e.g.
in OpenWrt.
The patch was autogenerated with the following commands:
$EDITOR core.h
sed -i "s/\<readl\>/dwc2_readl/g" *.c hcd.h hw.h
sed -i "s/\<writel\>/dwc2_writel/g" *.c hcd.h hw.h
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
SVN-Revision: 44675
Lantiq driver does not work with autodetected fifo sizes so use ones
from original ltq-hcd driver in dwc2. Other values can be
autodetected.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
SVN-Revision: 44674
Port gpio code from original ltq-hcd driver to dwc2.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
SVN-Revision: 44673
Add VR9 specific usb initialization bits from ltq-hcd to platform
initialization.
This patch is more of a proof-of-concept than production quality
since the initialization registers are different on other lantiq
platforms.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
SVN-Revision: 44672
Matteo Croce
Hauke Mehrtens
Rafał Miłecki
John Crispin
Felix Fietkau
Jonas Gorski
Imre Kaloz