Fix the WLAN MAC address to match the one printed on the label by using the
correct address from the ART instead of the address of the LAN interface.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 44183
The mac address usually write in factory block. but sometime user erase this block , the mac address will change to ff:ff:ff:ff:ff:ff.
This patch is purpose to fix this issue.
Signed-off-by: wengbj <linux.c@foxmail.com>
SVN-Revision: 44166
This patch adds an entry in the uci-defaults' led-file to configure the
WAN and WLAN LEDs by default.
Signed-off-by: Vincent Wiemann <me@bibbl.com>
SVN-Revision: 44165
Changeset r43049 removed the "062-mips_decompressor_build_fix.patch" which is
still required to properly build the xburst kernel.
Fix the syntax error in the preprocessed code by explicitely undefining the
"memcpy" and "memset" macros prior to declaring the replacements functions.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 44133
Using port-based VLANs depends on a non-standard
swconfig parameter, which compilcates things like
LuCI that don't know about it. This patch changes
the default to use 802.1q VLANs internally in the
switch, but without tagging packets since we have
two Ethernet ports.
iperf3 tests indicate no difference in performance
versus port-based VLANs when the CPU port is not
using tags.
Signed-off-by: Claudio Leite <leitec@staticky.com>
SVN-Revision: 44122
* fix TSO features verify on mt7621 firewrt board
* improve tx clean up. no need to access uncached
memory. also use TX_DTX register instead of
read tx ring DONE bit
* mt7621 need napi weight 64 to get more performance
* remove netif_receive_skb, after kernel version
3.7 tcp4_gro_receive can handle tcp checksum.
on rt2880 use iperf tcp LAN to WAN throughput test.
with gro 135 Mbits/sec. without gro 80.4Mbits/sec.
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 44118
on mt7621 don't have tx vlan vid registers.
so set FE_REG_FE_DMA_VID_BASE to 0.
set rx vlan offload register to disable.
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 44117
the rx_buf_size now is 1534 when mtu is 1500.
the ethernet frame with vlan tag and FCS is 1522.
so the buffer is enough.
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 44116
Add global read-only swconfig attribute "arl_table" to display the
address resolution table.
So far the chip-specific part is implemented for AR8327/AR8337 only
as I don't have the datasheets for the other AR8XXX chips.
Successfully tested on TL-WDR4300 (AR8327rev2)
and TL-WDR4900 (AR8327rev4).
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 44104
Until a few years ago the page switch wait time was set to msleep(1)
what was changed to usleep_range(1000, 2000) later.
I can not imagine that a low-level operation like switching page
on register level takes so much time.
Most likely the value of 1ms was initially set to check whether
it fixes an issue and then remained w/o further checking whether
also a smaller value would be sufficient.
Now the wait time is set to 5us and I successfully tested this on
AR8327. IMHO 5us should be plenty of time for all supported chips.
However I couldn't test this due to missing hardware.
If other chips should need a longer wait time we can add the
wait time as a parameter to the ar8xxx_chip struct.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 44103
Check for switch port link changes and
- flush ATU in case of a change
- report link change via syslog
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 44102
The functionality to flush the address translation table contains two bugs
which luckily compensate each other.
1. Just setting the operation is not sufficient to perform the flushing.
The "active" bit needs to be set to actually trigger an action.
For the vtu operations this is implemented correctly.
2. ar8xxx_phy_read_status is called every 2s by the phy state machine
to check for link changes. This would have caused an ATU flush
every 2s.
Fix the chip-specific ATU flush functions and remove the ATU flush call
from ar8xxx_phy_read_status.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 44101
TP-LINK TL-WR843ND v1 is the same model like wr41, but with
Power over Ethernet on wan port.
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
SVN-Revision: 44085
This adds a patch to target/linux/lantiq/patches-3.14
fixing a bug clock code on ar9. The current version returns
the wrong value for the fpi clock frequency in some
cases.
See discussion for further details:
https://lists.openwrt.org/pipermail/openwrt-devel/2015-January/030688.html
I'm not sure about the patch naming and numbering convention.
Do please let me know it this is not OK.
Many thanks,
Ben Mulvihill
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
SVN-Revision: 44083
the GPIO controlling the rf filter is not configured properly by this patch.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 44077
This patch is a follow up for my previous patch:
"ramips: add support for Intenso Memory 2 Move USB 3.0".
It fixes a couple of errors in the DTS (one of which broke
the gpio-buttons). The kmod-leds-gpio dependency has been
dropped as it is already part of the ramips target.
Furthermore the ramdisk/uImage image is generated by default
for the rt3050 subtarget. This image is needed to flash
OpenWrt for the first time onto the device via TFTP.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
SVN-Revision: 44072
The dLAN USB Extender profile was referecing binary packages which are not to
be included in any of the source-only feeds. Instead remove these references
and document how to use the 3rd party feed.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 44071
Ths will allow us to use early 3xx numbers for patches designed for
sending mainline.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 44057
* use default timeout value
* print more debug ring info
* move timeout reset function to workqueue
Signed-off-by: michael lee <igvtee@gmail.com>
SVN-Revision: 44043
This patch builds on the previous three to streamline support for the
Netgear DGN3500.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
SVN-Revision: 44032
It seems the call to ltq_get_eth_mac() disappeared at some point. This
patch puts it where it currently most makes sense.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
SVN-Revision: 44031
Somewhere in the conversion of the MIPS architecture code to Device Tree
usage, there's been a failure to keep the separate variables holding the
kernel command line reconciled between the tree and the bootloader. This
patch restores previous functionality that broke.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
SVN-Revision: 44030
Currently this initscript fails if the macaddr has any leading zeroes.
This patch corrects the problem.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
SVN-Revision: 44029
The swconfig get_link attribute (at least) on AR8327/AR8337 doesn't
consider the autonegotiated flow control.
AR8327/AR8337 provide the info about autonegotiated rx/tx flow control
in bits 10 and 11 of the port status register.
Use these values to display info about autonegotiated rx/tx flow
control as part of the get_link attribute.
Successfully tested on TL-WDR4900 (AR8327 rev.4) and
TL-WDR4300 (AR8327 rev.2).
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 44023
AR8327/AR8337 allow to read the result of EEE autonegotiation.
If EEE is autonegotiated between the link partners, display
this as part of the swconfig get_link attribute.
eee100: 100MBit EEE supported by both link partners
eee1000: 1GBit EEE supported by both link partners
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 44022
Users reported network issues with AR8327 which turned out to be caused
by EEE not working correctly with certain link partners (ticket 14597).
The workaround was to disable EEE on all ports (changeset 41577).
The issue was with certain link partners only, therefore this patch
allows to control usage of EEE per port via swconfig.
Still the default is to initially disable EEE on all ports.
Successfully tested on a TL-WDR4900 (AR8327 rev.4)
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 44021
Rafał Miłecki
Zoltan Herpai
Jo-Philipp Wich
John Crispin
Luka Perkov
Imre Kaloz
Felix Fietkau
Florian Fainelli