Commit Graph

17592 Commits (97212262d5b9be333be439efacb6c66f664726a9)

Author SHA1 Message Date
Mirko Parthey d517f04343 brcm47xx: fix button inversion for Asus WL-500W
The Asus WL-500W buttons are active high,
but the software treats them as active low.
Fix the inverted logic.

Signed-off-by: Mirko Parthey <mirko.parthey@web.de>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-02-16 00:06:22 +01:00
Mirko Parthey ac3a4e7ae2 brcm47xx: fix USB driver choice for Asus WL-500W
BCM4704 SoC has only USB 1.1 core:
ssb: Core 3 found: USB 1.1 Hostdev (cc 0x808, rev 0x03, vendor 0x4243)
but this device actually comes with two USB 2.0 ports.

It appears embedded controller isn't used but instead there are two PCI
attached controllers (next to the BCM4321 wireless card):
1106:3038 VT82xx/62xx UHCI USB 1.1 Controller
1106:3104 USB 2.0

Choose a set of USB drivers which actually support this hardware.

Signed-off-by: Mirko Parthey <mirko.parthey@web.de>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-02-15 23:43:19 +01:00
Felix Fietkau 1e1a0592f8 kernel: fix crashes on MIPS when loading kernel modules under memory pressure
When memory is tight, modules may need to be loaded into vmalloc()
space. The code then has to generate jump trampolines which enable
relocations between vmalloc space and physical address space.

The code had a bug that was freeing these trampolines even when the
module was successfully loaded.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-02-15 12:35:17 +01:00
Thibaut VARENE 748e701b74 ar71xx: add preliminary kernel support for several RB SPI NOR devices
The cAP 2nD, mAP 2nD and wAP 2nD apparently all share the same QCA953x/SPI-NOR
platform.

This patch adds preliminary kernel support based on init data used in
Mikrotik's linux-3.3.5 kernel patch. Since this is totally experimental and
untested, the necessary glue in base-files has not been added, the code is
provided as a starting point in case somebody with that hardware wants to help
getting it supported.

The cAP lite (cAPL 2nD) should also be supported once it is determined whether
or not it uses the same board identifier as the mAP lite.

Code has been successfully built and has no side effect (no impact on already
supported devices).

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-02-15 11:28:59 +01:00
Thibaut VARENE b800453282 ar71xx: add new SPI NOR RB devices to the list of serial-enable patch
Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-02-15 11:28:59 +01:00
Thibaut VARENE b2044a7f60 ar71xx: add support for RB750r2
This patch adds support for the MikroTik RouterBOARD hEX lite
https://routerboard.com/RB750r2

Specifications:
- SoC: Qualcomm QCA9531 (850MHz)
- RAM: 64MB
- Storage: 16MB NOR SPI flash
- Ethernet: 5x100M (1 PoE in)

This ethernet router is based on the same platform as the hEX PoE lite (it
shares the same board identifier), but has no USB and no PoE out.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-02-15 11:28:58 +01:00
Thibaut VARENE 19f42663d2 ar71xx: add support for RB750UPr2
This patch adds support for the MikroTik RouterBOARD hEX PoE lite
https://routerboard.com/RB750UPr2

Specifications:
- SoC: Qualcomm QCA9531 (650MHz)
- RAM: 64MB
- Storage: 16MB NOR SPI flash
- Ethernet: 5x100M (1 PoE in, 1 PoE out)
- USB: Type A

This ethernet router is based on the same platform as the wireless router hAP.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-02-15 11:28:58 +01:00
Thibaut VARENE 8cbb2ac633 ar71xx: add support for RB951Ui-2nD
This patch adds support for the MikroTik RouterBOARD hAP
https://routerboard.com/RB951Ui-2nD

Specifications:
- SoC: Qualcomm QCA9531 (650MHz)
- RAM: 64MB
- Storage: 16MB NOR SPI flash
- Wireless: builtin QCA9531, 2x2:2
- Ethernet: 5x100M (1 PoE in, 1 PoE out)
- USB: Type A

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-02-15 11:28:58 +01:00
Thibaut VARENE b18bae37a4 ar71xx: provide support for RB-941-2nD via mach-rbspi.c
This patch implements support for the hAP lite in mach-rbspi.c

hAP lite was supported via mach-rb941.c, so this file is removed
as well as the corresponding build bits.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-02-15 11:28:57 +01:00
Thibaut VARENE c59fa94eee ar71xx: add support for RB mAP L-2nD
This patch adds support for the MikroTik RouterBOARD mAP lite
https://routerboard.com/RBmAPL-2nD

Specifications:
- SoC: Qualcomm QCA9533 (650MHz)
- RAM: 64MB
- Storage: 16MB NOR SPI flash
- Wireless: builtin QCA9533, 2x2:2
- Ethernet: 1x100M

This is another 16M SPI NOR mikrotik device. The machine file is named
mach-rbspi.c because I plan to add support for several of the other spi-based
RouterBOARD devices in subsequent patches: they share most of the hardware
and thus the same codebase.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-02-15 11:28:57 +01:00
Daniel Golle d57223259b ramips: replace remaining instances of ralink, port-map
Some boards were apparently forgotten when ralink,portmap was renamed
to mediatek,portmap -- probably because they used the long obsolete
ralink,port-map attribute.
If this commit breaks ethernet wan/lan assignment, this is because
the port-map attribute wasn't actually parsed, you'll have to replace
"wllll" by "llllw" in the dts file belonging to that board (and send
a patch doing that!)

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2017-02-15 09:12:40 +01:00
John Crispin 6cb0372d42 ramips: fix mt7621 ethernet support for v4.9
Signed-off-by: John Crispin <john@phrozen.org>
2017-02-15 09:12:00 +01:00
John Crispin 38f9d08f57 kernel: add missing symbol for v4.9
Signed-off-by: John Crispin <john@phrozen.org>
2017-02-15 09:11:11 +01:00
Chris Blake 9a6c932556 x86: Add board configs for the PC Engines APU2
This adds the default LED and network settings for the PC Engines APU2
when running under the x86 target.

[dwmw2: Change Ethernet port setup]
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
2017-02-15 07:52:28 +01:00
David Woodhouse add465f1be x86: Enable DIAG LED on Geos
Based on a patch from Chris Blake <chrisrblake93@gmail.com>, except let's
do it by using the LED configuration instead of hard-coding it for each
board type. And try using /bin/board_detect to do the default behaviour,
on the first boot where the config hasn't yet been generated.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2017-02-15 07:52:28 +01:00
Chris Blake 27a635f0b4 x86: Move Traverse Geos configs into x86 base-files
This change moves the files in 657418d to the root of the x86 target.
This is done in preperation for adding more devices under other
subtargets.

CC: David Woodhouse <dwmw2@infradead.org>

Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
2017-02-15 07:52:28 +01:00
Giuseppe Lippolis 35c60d18c5 ramips: export slic IRQ line in dwr-512
The DWR-512 embeds the hw slic device si3210. This device have the IRQ line
attached to the gpio1. This patch export the gpio1 with proper name and
parameters to the sysfs.

Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
2017-02-15 07:45:54 +01:00
John Crispin c186a48fca octeon: only copy sysupgrade file if present
this caused

'mv: can't rename '/mnt/sysupgrade.tgz': No such file or directory'

when running sysupgrade -n

Signed-off-by: John Crispin <john@phrozen.org>
2017-02-15 06:36:21 +01:00
John Crispin 1753720261 octeon: bump to v4.9
Signed-off-by: John Crispin <john@phrozen.org>
2017-02-14 17:14:27 +01:00
Felix Fietkau 9dcb921d90 build: add buildbot specific config option for setting defaults
This can be used to tweak the buildbot behavior without having to change
buildbot's configuration.
It will also allow us to add more aggressive clean steps (e.g. on
toolchain changes), which would break developers' workflows if enable
by default.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-02-14 14:18:35 +01:00
Felix Fietkau f5977c0c0a ramips: revert faulty 4.4 config change from 9c24227090
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-02-14 13:47:21 +01:00
Felix Fietkau f533b94436 ar71xx: fix DEFAULT_PACKAGES for mikrotik devices
Include packages from the default profile for NAND devices

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-02-14 13:15:44 +01:00
Alexandru Gagniuc 6cce9557a0 ar71xx: Add support for D-Link EBR-2310 Rev. C
Add support for the EBR-2310, which is almost identical to the DIR-615
rev E4, without the wifi.

Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
2017-02-14 12:27:14 +01:00
Piotr Dymacz 56561b9f51 ar71xx: add support for TP-Link TL-WA850RE v2
TP-Link TL-WA850RE v2 is a wall-plug N300 Wi-Fi range extender,
based on Qualcomm/Atheros QCA9533 v2.

Short specification:

- 550/391/195 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 32 MB of RAM (DDR1)
- 4 MB of FLASH
- 2T2R 2.4 GHz
- 2x internal antennas (embedded on PCB)
- 9x LED (all can be turned off with GPIO15), 2x button
- UART (J3) header on PCB

Flash instruction: use "factory" image directly in vendor GUI.

Warning: this device does not include any kind of recovery mechanism
in the bootloader and disassembling process is not trivial.

You can access vendor firmware over serial line using:
- login: root
- password: sohoadmin

Image was tested only in US version of the device, but should work
also with the same device version sold in other countries.

Available FLASH space, with LEDE trunk, is only 240 KB.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-02-14 12:25:33 +01:00
Furong Xu a9fdb35740 ramips: Clean duplicated status property for Omega2 WMAC in dtsi
At the tail of dtsi, wmac is enabled twice, clean the first one

Signed-off-by: Furong Xu <xfr@outlook.com>
2017-02-14 12:19:56 +01:00
Giuseppe Lippolis 85766c8d70 ramips: fixed sms led polarity into dwr-512 DT
Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
2017-02-14 12:19:35 +01:00
Thibaut VARENE 157353c210 ramips: WN3000RPv3: do not setup switch
The WN3000RPv3 is a repeater with a single ethernet port. Setting up the
switch, even to disable it, is unnecessary and possibly confusing.

Configure LAN as eth0 instead.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-02-14 12:19:12 +01:00
Sven Eckelmann 3d16c16eb6 ar71xx: Add missing device package om-watchdog for MR1750
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2017-02-14 12:18:05 +01:00
Sven Eckelmann 391d498fe5 ar71xx: add OpenMesh A40 to OpenMesh A60 profile
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2017-02-14 12:18:05 +01:00
Sven Eckelmann d0061798a6 ar71xx: extract ath10k wifi board.bin for the OpenMesh A40 board
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2017-02-14 12:18:05 +01:00
Sven Eckelmann c6e1bb2ace ar71xx: enable sysupgrade for the OpenMesh A40
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2017-02-14 12:18:05 +01:00
Sven Eckelmann 640f9158e2 ar71xx: add user-space support for the OpenMesh A40
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2017-02-14 12:18:05 +01:00
Sven Eckelmann 5e61a8331d ar71xx: add kernel support for the OpenMesh A40 board
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2017-02-14 12:18:05 +01:00
Sven Eckelmann 5e50adeed3 ar71xx: create profile and build image for the OpenMesh A60 board
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2017-02-14 12:18:05 +01:00
Sven Eckelmann 1330ff189b ar71xx: extract ath10k wifi board.bin for the OpenMesh A60 board
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2017-02-14 12:18:05 +01:00
Sven Eckelmann fce57c4082 ar71xx: enable sysupgrade for the OpenMesh A60
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2017-02-14 12:18:05 +01:00
Sven Eckelmann 174605c467 ar71xx: add user-space support for the OpenMesh A60
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2017-02-14 12:18:05 +01:00
Sven Eckelmann 417f9e7e82 ar71xx: add kernel support for the OpenMesh A60 board
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2017-02-14 12:18:05 +01:00
Sven Eckelmann baaf0acded ar71xx: enable sysupgrade for the OpenMesh OM2Pv4/-HSv4
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2017-02-14 12:18:04 +01:00
Sven Eckelmann bdfe4c1218 ar71xx: add user-space support for the OpenMesh OM2Pv4/-HSv4
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2017-02-14 12:18:04 +01:00
Sven Eckelmann e1b50457b0 ar71xx: add kernel support for the OpenMesh OM2Pv4/-HSv4
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2017-02-14 12:18:04 +01:00
Sven Eckelmann 019276a9c6 ar71xx: Remove the v2/v3 from the OpenMesh profile names
The list of v2/v3 devices is getting longer and makes reading the names of
the profiles unnecessary hard.

Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
2017-02-14 12:18:04 +01:00
John Crispin 9c24227090 ramips: add v4.9 support
NAND support is missing

Signed-off-by: John Crispin <john@phrozen.org>
2017-02-14 12:17:52 +01:00
Jonas Gorski c0841b3c4e mvebu: append metadata to clearfog sd card images
Fixes the following issue:

root@LEDE:/# sysupgrade /tmp/lede-mvebu-armada-388-clearfog-sdcard.img.gz
Saving metaconfig...
Image metadata not found
Use sysupgrade -F to override this check when downgrading or flashing to vendor firmware
Image check 'fwtool_check_image' failed.
root@LEDE:/#

Acked-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2017-02-13 17:50:41 +01:00
Felix Fietkau 90728c796d sdk: clean scripts/config before packing tarball (FS#504)
Avoids shipping potentially incompatible object files and also reduces
the tarball size

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-02-13 11:46:14 +01:00
Felix Fietkau fcea190b8b cns3xxx: disable watchdog until it is fixed
It has been reported to cause random reboots on some devices

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-02-13 11:30:56 +01:00
Felix Fietkau fec57b40c3 kernel: add missing tracing related config symbols for linux 4.9
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-02-13 10:39:54 +01:00
John Crispin 60a52cd4b4 apm821xx: adds missing symbol to v4.9 default config
Signed-off-by: John Crispin <john@phrozen.org>
2017-02-13 10:24:32 +01:00
Giuseppe Lippolis ec0f20212e ramips: added image size into dwr-512 DT
Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
2017-02-13 10:24:32 +01:00
Yangbo Lu 3c01fd0119 layerscape: fix adjust_link for 10G & 2.5G
Added a linux-4.4 patch to fix adjust_link for 10G & 2.5G.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2017-02-13 10:24:32 +01:00
Chuanhong Guo 634328c0de ramips: correct switch configuration for Newifi D1
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2017-02-13 10:24:32 +01:00
Martin Blumenstingl 70395ae8cb lantiq: fix patching the wifi mac address on BTHOMEHUBV3A
The firmware hotplug script tries to read the mac address from a
partition with the name "uboot-env" which does not exist (instead it's
name is uboot_env). This broke calculation of the new checksum (after
patching the mac address) which resulted in ath9k refusing to use the
EEPROM data.

The original error reported by ath9k was:
PCI: Enabling device 0000:00:0e.0 (0000 -> 0002)
ath: phy0: Bad EEPROM checksum 0x2523
ath: phy0: Unable to initialize hardware; initialization status: -22
ath9k 0000:00:0e.0: Failed to initialize device

Fixes: a20616863d ("lantiq: use ath9k device tree bindings
binding/owl-loader")

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2017-02-13 07:57:15 +01:00
Thibaut VARENE 33154eaf41 ar71xx: fix platform_find_rootfspart()
platform_find_rootfspart() fails if the kernel partition comes before the
rootfs partition. The proposed patch fixes this while preserving what I
understand was the original idea: stop at first match.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
2017-02-12 15:57:37 +01:00
Hauke Mehrtens 5c651b029e kernel: fix kmod-rxrpc with kernel 4.9
rxkad will be build into af-rxrpc now and is of type boolean.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-02-12 13:55:45 +01:00
Martin Blumenstingl 0caffa60af kernel: fix compile error on linux 4.9 with CONFIG_KALLSYMS disabled
Upstream linux commit 7523e4dc5057e "module: use a structure to
encapsulate layout." moves some of the struct module members into a
separate struct module_layout.

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
2017-02-12 13:55:13 +01:00
Hauke Mehrtens b1c2506a76 kernel: MIPS: IRQ Stack: Fix erroneous jal to plat_irq_dispatch
This backports the following fix to our mips IRQ stack patches:
https://patchwork.linux-mips.org/patch/15110/

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-02-12 01:41:43 +01:00
Hauke Mehrtens 136d4a0656 lantiq: fix section mismatch in PCIe driver
Do not put the probe function into the __init section, but use the normal
section. This fixes a section mismatch warning.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-02-12 01:29:41 +01:00
Hauke Mehrtens 863e79f8d5 lantiq: add support for kernel 4.9
The following patches were dropped because they are already applied
upstream:
0012-pinctrl-lantiq-fix-up-pinmux.patch
0013-MTD-lantiq-xway-fix-invalid-operator.patch
0014-MTD-lantiq-xway-the-latched-command-should-be-persis.patch
0015-MTD-lantiq-xway-remove-endless-loop.patch
0016-MTD-lantiq-xway-add-missing-write_buf-and-read_buf-t.patch
0017-MTD-xway-fix-nand-locking.patch
0044-pinctrl-lantiq-introduce-new-dedicated-devicetree-bi.patch
0045-pinctrl-lantiq-Fix-GPIO-Setup-of-GPIO-Port3.patch
0046-pinctrl-lantiq-2-pins-have-the-wrong-mux-list.patch
0047-irq-fixes.patch
0047-mtd-plat-nand-pass-of-node.patch
0060-usb-dwc2-Add-support-for-Lantiq-ARX-and-XRX-SoCs.patch
0120-MIPS-lantiq-add-support-for-device-tree-file-from-bo.patch
0121-MIPS-lantiq-make-it-possible-to-build-in-no-device-t.patch
122-MIPS-store-the-appended-dtb-address-in-a-variable.patch

The PHY driver was reduced to the code adding the LED configuration,
the rest is already upstream:
0023-NET-PHY-adds-driver-for-lantiq-PHY11G.patch

The SPI driver was replaced with the version pending for upstream
inclusion:
New driver:
0090-spi-add-transfer_status-callback.patch
0091-spi-lantiq-ssc-add-support-for-Lantiq-SSC-SPI-controller.patch
Old driver:
0100-spi-add-support-for-Lantiq-SPI-controller.patch

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-02-11 23:44:13 +01:00
Hauke Mehrtens d61a799528 kernel: add missing config option for kernel 4.9
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-02-11 23:28:18 +01:00
Hauke Mehrtens 11215fb23c kernel: add rest controller option for kernel 4.9
Deactivate the reset controllers which could be activated on kernel 4.9
by default.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2017-02-11 23:28:13 +01:00
Felix Fietkau e9f76f0f46 cns3xxx: clean up patches
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-02-11 21:18:42 +01:00
Alberto Bursi 4383c13aee kirkwood: add ZyXEL NSA325 device
This patch add ZyXEL NSA325 2-Bay Media Server

The ZyXEL NSA325 device is a Kirkwood based NAS:

- SoC: Marvell 88F6702 1600Mhz
- SDRAM memory: 512MB DDR2 400Mhz
- Gigabit ethernet: Marvell Alaska
- Flash memory: 128MB
- 1 Power button
- 1 Power LED (blue)
- 5 Status LED (green/red)
- 1 Copy/Sync button
- 1 Reset button
- 2 SATA II ports (internal)
- 2 USB 2.0 ports (back)
- 1 USB 3.0 port (front)
- Fan (fixed speed)
- hardware watchdog in a mcu

Basically a bigger, more powerful version of NSA310,
installation is the same as they share the same flash layout.

A notable difference is that there is a hardware watchdog
in a mcu on the board, which is disabled by default in the LEDE u-boot.
The watchdog is also disabled with a GPIO activation through
raw register change when kwbooting or it would reset the board before
the new uboot was transferred.

Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [remove dead code]
2017-02-11 21:16:28 +01:00
Alberto Bursi f99178b6c0 kirkwood: cleanup nsa310b mac address extraction
switch nsa310b mac address reading to mtd_get_mac_ascii helper as
it seems the fw_env.config file is created way later than when
network is set up, when I tested I still had that file included
in the image through /files folder.

Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
2017-02-11 21:16:28 +01:00
Christian Lamparter 9a9f2f97e6 apm821xx: add linux 4.9 apm821xx patches
This patch updates the apm821xx target to use the 4.9 kernel.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
2017-02-11 20:57:56 +01:00
David Woodhouse 657418db68 x86: Add configuration back for Traverse Geos
When we merged all the Geode boards into one generic target, the default
network and LED configuration was lost. Put it back.

Fixes: 9e0759ea26 ("x86: merge all geode based subtargets into one")
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2017-02-11 20:34:07 +01:00
Felix Fietkau e0e5f8ca2f kernel: fix linux 4.9 host tools portability issues
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-02-11 19:02:52 +01:00
Tim Harvey 092f2c14bd imx6: move to Linux 4.9 kernel
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-02-11 15:38:11 +01:00
Felix Fietkau 73ea3c3f9c cns3xxx: add back watchdog support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-02-11 15:36:35 +01:00
John Crispin 84e784671b kernel: add missing symbols to generic/config-4.9
Signed-off-by: John Crispin <john@phrozen.org>
2017-02-11 06:52:32 +01:00
John Crispin 4bdf3a33ad kernel: fix 304-mips_disable_fpu.patch for v4.9
the function prototype has changed, make the new stub consistent with this
change.

Signed-off-by: John Crispin <john@phrozen.org>
2017-02-11 06:52:32 +01:00
Koen Vandeputte 2c416b1db0 cns3xxx: switch to linux 4.9
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2017-02-10 11:05:57 +01:00
Koen Vandeputte 1db4135e32 cns3xxx: add preliminary 4.9 support
Adds preliminary kernel 4.9 support for this target.

- Refreshed/Updated all patches

Added 3 new patches:
- 093 --> Add virtual PCI MMIO mapping
- 230 --> Remove deprecated code
- 240 --> Rework AT24 eeprom code to use the new NVMEM API

Compiled & tested on cns3xxx (gw2388)

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2017-02-10 11:05:57 +01:00
Felix Fietkau e690280a16 mxs: enable nvmem support
fixes build error due to missing kernel config options

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-02-10 11:05:57 +01:00
Rafał Miłecki db866154fc kernel: move upstream accepted bcm47xxpart TRX cleanups
Use 0xx prefix for accepted patches.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-02-10 08:30:16 +01:00
Daniel Gonzalez Cabanelas 41ad9ed13a brcm63xx: Add Observa VH4032N support
Add support for the Observa Telecom VH4032N router.

This is another BCM6368 router, 128 MB RAM, 32MB flash and 3 USB
host ports.

The wifi chip is an onboard Broadcom BCM43222.

Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
[jonas.gorski: use gpio-hog instead of abusing ephy-reset]
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2017-02-09 22:02:45 +01:00
Felix Fietkau 7096ed58fd kernel: remove kmod packages for bridge, stp, llc and 8021q
Remove CONFIG_VLAN_8021Q overrides for two targets
These features are built into the kernel image for all targets

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-02-09 14:49:34 +01:00
Jonas Gorski 0127c480bb brcm63xx: Neufbox 6: fix switch by probing through DT
Probe the switch through DT instead of a platform device. This fixes
probe, as GPIO offsets are now properly accounted for.

Fixes the following issue:

[    0.802953] 8021q: 802.1Q VLAN Support v1.8
[    0.810518] rtl8366_smi: gpio_request failed for 18, err=-517

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2017-02-09 14:30:44 +01:00
Jonas Gorski 8b741d5cd1 brcm63xx: fix lzma loader for BCM6362
BCM6362 and BCM3380 seem to share the same PRID. Disable serial output
for them until we can find a way to tell them apart reliably.

Fixes: 8f3cfe4ba2 ("brcm63xx: lzma-loader: add BCM3380 support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2017-02-09 14:30:44 +01:00
Paul Wassi 9d4f8ff4f6 brcm63xx: add support for Pirelli/ADB P.DG AV4202N
This patch adds support for the ADB P.DG AV4202N aka Pirelli PRG AV4202N.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2017-02-09 14:30:44 +01:00
Jonas Gorski 31d5c5bc90 brcm63xx: setup internal switch leds for bcm6368
Setup the GPIO_MODE register bits for used internal switch port leds.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2017-02-09 14:30:44 +01:00
Jonas Gorski c7f31b280f brcm63xx: do a full reset phy cycle
Make sure we do a proper reset of the phy, if the phy reset is defined.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2017-02-09 14:30:44 +01:00
Jonas Gorski dd7079e79a brcm63xx: implement gpio_to_irq for bcm63xx-gpio
Add support for mapping some GPIO lines to IRQs. GPIO to IRQ mappings
were found out through experimentation, helped by having the GPIO as
output still toggling the IRQ input.

Based-on: http://patchwork.ozlabs.org/patch/660534/
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2017-02-09 14:30:43 +01:00
Jonas Gorski 94bbd1f057 brcm63xx: fix external interrupts on BCM6318
Setting the clear bit for an interrupt seems to cause interrupts to be
deasserted again immediately. So unset the bit for BCM6318 to allow
subsequent interrupts to still work.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2017-02-09 14:30:43 +01:00
Felix Fietkau d826af2cbb build: make <subdir>/install opt-in, use it for target/ only
Fixes buildbot errors on running make target/install or
toolchain/install

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-02-09 13:51:35 +01:00
Piotr Dymacz f5416b0622 ar71xx: image: drop redundant CONSOLE assignment
Default CONSOLE value for ar71xx target is "ttyS0,115200", so there
is no need to specify the same value in device profiles.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-02-09 09:45:27 +01:00
Alexey Brodkin aab344d227 arc770: backport upstream fix for unaligned access
This commit reverts 42f3c1f ("arc770: fix broken upstream change")
and simultaneously adds back-ported fix from Linus' tree:
a524c218bc94 ("ARC: [arcompact] brown paper bag bug in unaligned
access delay slot fixup").

Note mentioned patch will appear in stable trees soon as well so
IMHO there's not much sense in adding this separate patch in lede/master branch.
As well as we will get rid of it here in 17.01 once we bump 4.4 kernel here
later down the line.

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Felix Fietkau <nbd@nbd.name>
Cc: John Crispin <john@phrozen.org>
Cc: Jo-Philipp Wich <jo@mein.io>
2017-02-09 09:14:45 +01:00
Claudio Leite 290ca2ba46 ramips: fix AR670W partition alignment
mtdsplit_lzma requires that the rootfs be aligned to a block boundary.
Pad the kernel partition to make this so.

Signed-off-by: Claudio Leite <leitec@gmail.com>
2017-02-09 09:14:45 +01:00
Rafał Miłecki 76eb62e5af kernel: backport bcm47xxsflash support for reading 32 MiB flashes
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-02-09 08:41:23 +01:00
Álvaro Fernández Rojas 48b71a0b07 brcm2708: bcm2708: fix build
buildbot fails to build without regmap, which I couldn't reproduce locally.
Hopefully this fixes it.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2017-02-08 17:43:40 +01:00
Felix Fietkau 412cf4cc51 sdk: add missing change from r3328-f55c29e4c7
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2017-02-08 12:01:59 +01:00
Álvaro Fernández Rojas ba9dbc3dd5 brcm2708: add more patches for linux 4.9
Also removes unneeded wireless patches

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2017-02-08 09:59:53 +01:00
Álvaro Fernández Rojas 7ef713c9c4 brcm2708: bcm2710: add 64 bit support for Raspberry Pi 3
64 bit support for Raspberry Pi 3 is experimental. However, bcm2709 subtarget
should serve as a stable and compatible 32 bit support.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2017-02-08 00:41:51 +01:00
Álvaro Fernández Rojas 77a00027c3 brcm2708: bcm2709: add support for Raspberry Pi 3
This adds support for Raspberry Pi 3 on the bcm2709 subtarget, in order to
keep 32 bit image support when 64 bit support is added on bcm2710 subtarget.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2017-02-08 00:41:48 +01:00
Álvaro Fernández Rojas de1f83097a generic: add missing symbols for linux 4.9
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2017-02-08 00:41:09 +01:00
Álvaro Fernández Rojas e9e52761d3 brcm2708: remove duplicated gzip from image generation
Images are now automatically gziped so remove custom image command

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2017-02-07 23:00:24 +01:00
Álvaro Fernández Rojas d9d090e520 brcm2708: remove linux 4.4 support
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2017-02-07 23:00:21 +01:00
Álvaro Fernández Rojas ada91d8a24 brcm2708: switch to linux 4.9
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2017-02-07 23:00:18 +01:00
Álvaro Fernández Rojas 96aa0c6b0b brcm2708: add linux 4.9 support
Patches from Raspberry Pi repo:
https://github.com/raspberrypi/linux/commits/rpi-4.9.y

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2017-02-07 23:00:16 +01:00
Álvaro Fernández Rojas 989a0b4846 generic: add missing kernel symbols
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2017-02-07 23:00:08 +01:00
Rafał Miłecki 2fd81681f9 bcm53xx: include Broadcom PHY driver in the kernel
Initial idea was to use package with this PHY driver for devices that
need it. Unfortunately this can't work as bgmac is built-in and PHY
probing happens before loading modules - it results in PHY subsystem
picking default (generic) PHY driver.

There were two ways of solving this:
1) Making bcm53xx use bgmac as module
xor
2) Built-in Broadcom PHY driver

After some quick discussion it seems we can simply built-in the driver
as increased kenel size is relatively small (1805 B).

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2017-02-07 18:11:17 +01:00