With this patch WPS discovery can be started or canceled over ubus if
WPS is enabled in wireless configuration. This is equivalent of
'hostapd_cli wps_pbc' and 'hostapd_cli wps_cancel' commands.
Signed-off-by: Petar Koretic <petar.koretic@sartura.hr>
SVN-Revision: 42459
This switches to kernel 3.10 that was prepared by Hauke in r41531 :
gemini: add support for kernel 3.10
This is compile tested only, please run test and report back.
I've simply checked if it still compiles, unfortunately we didn't get
any feedback for this target.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 42450
the old dwc_otg driver is starting to fall apart and fails on newer 3g
modems and some storage devices. switch to the upstream dwc2 driver which
is no longer in staging/.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 42446
While the AR9331 has a gigabit MAC towards the internal switch, the
integrated PHYs however are only 100-base-tx capable. The existing code
however advertieses gigabit capability in the link status word. If you
attach such a PHY to a gigabit capable switch on the remote end, with
some probability it attempts to negotiate gigabit and fails, falling
baco to the AR9331 assuming a 10mbit half-duplex link. This has been
observed quite frequently with the Carambola2 and gigabit capable
switches.
In ath79_register_eth(), "pdata->has_gbit = 1;" is set unconditionally
for both AR9331 ethernet ports. This is most likely wrong. Despite the
two MAC IP cores being gigabit MACs, the MAC for eth1 is connected to a
100base-T PHY via MII. The has_gbit attribute is used in the ethernet
driver to determine the supported link modes.
So either pdata->has_gbit is not set to 1 anymore, or the ethernet
driver needs to be modified to determine the advertised link code word
on another criteria than pdata->has_gbit. This patch implements the
former solution.
Signed-off-by: Harald Welte <laforge@gnumonks.org>
SVN-Revision: 42432
The DFS pattern detector now supports all three regions; ETSI, FCC and
JP, so there is no reason to not have it enabled anymore.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 42431
Some Kconfig options are only relevant for the legacy platforms, move
them where they belong
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 42416
We need a new kernel version to support Cortex-A5 based platforms such
as SAMA5GD3.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 42415
In preparation for adding 3.14 kernel support, move files and patches to
a separate per-version directory since some of them will have
incompatible changes (e.g: dts)
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 42413
The at91 OHCI driver has a separate Kconfig symbol with newer kernels,
include it.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 42411
In preparation for adding SAMA5D3 support, move the legacy ARMv5 based
platforms to a separate subtarget.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 42408
On brcm47xx (Huawei E970), I noticed that sysupgrade now tries to flash trx images which don't fit into the flash, resulting in non-booting system.
I found that mtd does trx size checking only when flashing to a partition called "linux". This patch changes this to be "firmware".
This matches the following patch which changed partition name in bcm47xxpart.c driver to "firmware":
commit 86b4d5ef68ca77ff6724ebb9bddd6b93239c87fc
Author: hauke <hauke@3c298f89-4303-0410-b956-a3cf2f4a3e73>
Date: Sun Dec 1 16:32:32 2013 +0000
brcm47xx: use "firmware" partition name
...
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 38973
Signed-off-by: Mathias Adam <m.adam--openwrt@adamis.de>
SVN-Revision: 42403
Luka Perkov
Felix Fietkau
Hauke Mehrtens
John Crispin
Steven Barth
Zoltan Herpai
Jonas Gorski
Nicolas Thill
Florian Fainelli