Commit Graph

417 Commits (3b5d29b96e4df80dbfbcc5bbb8a5898a9390c683)

Author SHA1 Message Date
John Crispin de7dce21a3 ralink: add WRTnode2 platform and led support
Signed-off-by: xzmu <xzmu@wrtnode.com>

SVN-Revision: 48049
2016-01-01 21:19:50 +00:00
Felix Fietkau eaf8889cf8 ramips: add a script to fix up the broken mac address on the witi board
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48027
2016-01-01 18:57:39 +00:00
John Crispin 4e31b2e869 ramips: add support for Ubiquiti EdgeRouter X (UBNT-ERX)
This router is based on MT7621 SoC, no wifi, no usb, nand.

Works:
* Boots.
* Ethernet.
* Switch.
* Button (reset).
* Flashing OpenWrt from stock firmware.
* Upgrading OpenWrt.

Doesn't work:
* No GPIO leds. All leds are controlled by switch,
  but stock firmware was able to control them.
* SoC has crypto engine but no open driver.
* SoC has nat acceleration, but no open driver.
* This router has 2MB spi flash soldered in but MT
  nand/spi drivers do not support pin sharing,
  so it is not accessable and disabled. Stock
  firmware could read it and it was empty.
* PoE out.

Router has serial pins populated. If looking at the top
of the router, then counting from Eth sockets pins go as:
'GND, RX, TX, GND'. 3.3v, 57600.

U-boot bootloader supports tftpboot, controlled from serial.
This router has two kernel partitions: 'live' and 'backup'.
They are swapped during flashing (on both stock and OpenWrt).
Active partition is controlled by a flag in a factory partition.
U-boot has custom command to switch active kernel partition.
Kernel partitions are 'bare flash' 3MB. Stock bootloader has
no UBI support. Stock rootfs is UBIFS.

Flashing procedure.
Stock firmware uses custom kernel patch to mount squashfs
from a file that is located on UBIFS volume. This makes wiping
out this volume from within stock firmware difficult.
Instead this patch builds image that is flashable by stock firmware
and contains initrams image (with minimal set of packages
to fit into kernel partition). Once this is flashed one can reboot
into initramfs OpenWrt and use sysupgrade to flash OpenWrt including
rootfs into nand.
Note: factory image is only built if initramfs image is enabled.

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>

SVN-Revision: 47881
2015-12-12 07:38:06 +00:00
Jo-Philipp Wich 67e1c87012 all: drop old uci-defaults.sh
Replace former uci-defaults.sh implementation with the uci-defaults-new.sh one
and update all users accordingly.

Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47867
2015-12-11 15:26:06 +00:00
John Crispin 9f14006809 ramips: add additional support for MQmaker WiTi board
The board is based on mt7621AT cpu, and has 16mb nor flash, 256mb of ram,
2 sata ports, microsd card slot, 1 USB 3.0 port and at least one 2.4 and
one 5 ghz antenna.

This is the 6th submission that adds support for XHCI in the device tree
file, along with switching the location of the 2 radio's and addition of
the kmod-i2c-mt7621 in the default packages of the profile.

Signed-off-by: Sebastian Careba <nitroshift@yahoo.com>

SVN-Revision: 47845
2015-12-11 15:04:13 +00:00
John Crispin 6cbb1be464 ramips: Fix support for PBR-M1 board
The PBR-M1 support in current OpenWrt is for the early demo board and it doesn't work on the final board.This patch fixes the support for it.

The LED called pbr-m1:buzzer is a beeper connected to GPIO26 so I used gpio-beeper instead of gpio-leds.

Signed-off-by: 郭传鈜 <gch981213@gmail.com>

SVN-Revision: 47844
2015-12-11 15:03:50 +00:00
Jo-Philipp Wich 527ec2af59 all: remove dummy ucidef_set_interface_loopback() from board.d
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47744
2015-12-03 23:13:00 +00:00
Jo-Philipp Wich 8f8b702f85 board.d: remove redundant ucidef_set_interfaces_lan_wan() calls
This removes calls to ucidef_set_interfaces_lan_wan() and
ucidef_set_interfaces_lan() on boards where all relevant info can be
inferred from the switch definition.

Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47722
2015-12-03 17:30:56 +00:00
Jo-Philipp Wich 9b02e73188 board.d: merge ucidef_add_switch() and ucidef_add_switch_ports()
This changes uci-defaults-new.sh, config_generate and all relevant board.d
files in order combine ucidef_add_switch() and ucidef_add_switch_ports() into
a single function.

Also removes now superfluous enable and reset arguments.

Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47721
2015-12-03 17:30:24 +00:00
Jo-Philipp Wich d17a64c7c0 base-files: uci-defaults-new: remove reset/enable args of ucidef_add_switch()
Out of 69 switch definitions, only 3 pass something different than "1" as
values for reset and enable, with one of those three being invalid.

This change ...

 * removes the reset and enable arguments from ucidef_add_switch()
 * unconditionally writes reset:1 and enable:1 to JSON
 * converts the three users of nonstandard values to ucidef_add_switch_attr()

Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47720
2015-12-03 17:30:08 +00:00
Jo-Philipp Wich de51026515 ramips: switch ucidef_add_switch_vlan() to ucidef_add_switch_ports()
This migrates the final board.d user of ucidef_add_switch_vlan() to the new
ucidef_add_switch_ports() approach, fixing some logic errors for a few boards
along the way.

Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47717
2015-12-03 15:46:29 +00:00
Jo-Philipp Wich ecf5b4fab7 ramips: hg255d: replace ucidef_set_led_interface() with ucidef_set_led_netdev()
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>

SVN-Revision: 47657
2015-11-26 12:46:04 +00:00
John Crispin 8c1f5141ce ralink: add support for netis WF-2881
netis WF-2881 is an MT7621AT based router with MT7602EN, MT7612EN.
It has 128MB DDR3, 128MB SLC NAND FLASH, 5-port Gbps switch and 1x USB 3.0.
The following patch adds support for this device.

this device only works on top of UBI.

Tested and working:
* ethernet
* both WiFi radios
* USB 3.0
* buttons (reset button)
* ethernet switch and USB diag LEDs
* UART
* GPIOs
* sysupgrade

Tested and not working
* failsafe

Signed-off-by: YounJae Rho <luxflow@live.com>

SVN-Revision: 47619
2015-11-24 18:29:26 +00:00
John Crispin e9baf8265b ramips: add support for Youku YK1
Changes since V1:
I resend this patch for current trunk.The former V1 patch is for CC branch.

Signed-off-by: Shonn Lu <countrysideboy@qq.com>

SVN-Revision: 47617
2015-11-24 18:29:02 +00:00
John Crispin dc699dd547 ramips: minor tweak to the lks7688 baord name
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47388
2015-11-05 10:01:23 +00:00
John Crispin 2350c149b5 ramips: add feature to blink led on sysupgrade
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47373
2015-11-03 13:32:02 +00:00
John Crispin 165244a222 ramips: add support for ZBT WG2626
Signed-off-by: Daniel Golle <daniel@makrotopia.org>

SVN-Revision: 47351
2015-11-02 10:18:19 +00:00
John Crispin 907c67fa87 ramips: preinit: use iproute2 instead of vconfig
Replace use of vconfig with the corresponding iproute2 syntax in
/lib/preinit/07_set_preinit_iface_ramips

The switch reset work-around needed on some ramips targets used the
deprecated vconfig tool to bring up the pre-init/failsafe interface.
This doesn't work on recent builds where vconfig is no longer being
deployed, resulting in the device being unreachable when triggered
into failsafe mode.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>

SVN-Revision: 47349
2015-11-02 10:18:02 +00:00
John Crispin 3760b95702 ramips: add support for Dovado tiny AC
Add support for Dovado tiny AC wifi router.

Soc: mt7620a
ram: 64MB
flash: 8MB
1x usb 2.0
two gigabit lan ports

5ghz wlan is not supported on this board since there is no gpl driverfor mt7610e wifi chip.

Signed-off-by: Andrej Vlasic <andrej.vlasic0@gmail.com>

SVN-Revision: 47348
2015-11-02 10:17:51 +00:00
John Crispin 83693c911a ramips: add function to change rt2x00 wifi eeprom mac
Some boards like dovado tiny ac have generic ralink mac in onflash wifi eeprom.
Add eeprom_set_macaddr function to rt2x00 eeprom extract script which changes mac addr insde eeprom dump.

Signed-off-by: Andrej Vlasic <andrej.vlasic0@gmail.com>

SVN-Revision: 47347
2015-11-02 10:17:41 +00:00
John Crispin 8fa6927415 ramips: add support for the Asus RP-N53 in the "02_network" boot script
This patch adds a case for the Asus RP-N53 in the "02_network" boot script. Without this, the lan interface does not get configured on startup, effectively bricking the device.

Signed-off-by:  Alberto Mattea <alberto@mattea.info>

SVN-Revision: 47345
2015-11-02 10:17:26 +00:00
John Crispin 51dd991d39 ramips: add LinkIt Smart7688 support
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 47203
2015-10-19 10:07:38 +00:00
John Crispin c10bdf11ff ramips: Add base-files for HiWiFi HC5x61 models
HiWiFi HC5661/5761/5861 models are manufactured by http://www.hiwifi.com. These models have similar hardware specs(MT7620A + 128M DDR2 + 16M flash). This patch adds support for them.

The original author is Justin Liu (rssnsj@gmail.com). I ported the patch to trunk and submitted it here with his approval.

v3 fix
   1: Fixed model order
   2: Remove manufacturer name from model name
   3: Use a hacky but prettier way to get mac address.

Signed-off-by: Xiaoning Kang <kangxn@163.com>

SVN-Revision: 47111
2015-10-05 10:25:47 +00:00
John Crispin 86a1e46b63 ramips: add proper mt7688 detection
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 46957
2015-09-16 08:31:00 +00:00
John Crispin 57c5910535 ramips: Added WIZnet WizFi630A Platform based on Ralink RT5350
This patch is to add the WIZnet WizFi630A board as a new platform. The board is in mini pci express form factor.

Signed-off-by: Tobias Welz <tw@wiznet.eu>

SVN-Revision: 46921
2015-09-14 20:09:31 +00:00
John Crispin 2efdc7c896 ramips: add support for Planex DB-WRT01
This patch add support for Planex DB-WRT01. DANBOARD route on
 the MT7620A SoC with two Ethernet port and a 802.11n 2.4 GHz radio.
 DANBOARD is Cartoon character.

Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>

SVN-Revision: 46918
2015-09-14 20:08:55 +00:00
John Crispin 0f155a330e ramips: base-files: optimize etc/diag.sh and etc/board.d/01_leds scripts
Instead of using board name provided explicitly as text in LED name, ex.:

[...]
mlwg2)
	status_led="mlwg2:blue:system"
[...]

use $board variable, which allows to combine together multiple boards with same color and LED names, ex:

[...]
mlw221|\
mlwg2)
	status_led="$board:blue:system"
[...]

The above approach allows to shrink size of code in base-files/etc/board.d/01_leds and base-files/etc/diag.sh scripts dramatically.
One thing to keep in mind here is that we assume to use proper and consistent LED naming scheme ("device:color:led-name").

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46665
2015-08-17 06:24:47 +00:00
John Crispin 1a392636a5 ramips: use consistent naming scheme for LEDs
The upstream LED naming convention is "device:color:led-name", but it seems that many of supported boards in OpenWrt don't follow this approach.
The following patch fixes this inconsistency in dts{,i} files and updates base-files scripts for ramips target:
 * fixes wrong indentation
 * keeps case statements structure in same convention as in other scripts (no empty line after ";;", no indentation for case...esac body)
 * fixes wrong LED names for some of boards (makes them the same as in dts{,i} files)
 * combines boards with same configuration (ex. set_wifi_led "rt2800pci-phy0::radio" in 01_leds)

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46664
2015-08-17 06:24:34 +00:00
John Crispin eba4a143c6 ramips: reorder the sysupgrade script
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 46660
2015-08-17 06:18:38 +00:00
John Crispin f32116987f ramips: remove unnecessary LED declaration for WT1520 in diag.sh
This device doesn't have defined LEDs in its dts file.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46635
2015-08-17 06:03:42 +00:00
John Crispin 2f0449419f ramips: fix indentation, case statements structure and optimize base-files/etc/board.d/02_network
The following patch:
 * fixes wrong indentation
 * combines together boards with same configuration
 * removes unnecessary spaces
 * removes empty lines after ";;" and uses only "|\" (for consistency)
 * orders boards alphabetically

in base-files/etc/board.d/02_network script.

One bug was left untouched: freestation5 board is listed twice in case statement, in ramips_setup_macs().

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46634
2015-08-17 06:02:59 +00:00
John Crispin 4069a8e49c ramips: be consistent with case statement in base-files/lib/upgrade/platform.sh
Always use "|\" (without spaces) and keep boards in alphabetical order.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46633
2015-08-17 06:01:49 +00:00
John Crispin a18b35a2f1 ramips: remove leading spaces, sort boards and optimize base-files/lib/ramips.sh
This patch:
 * fixes various mistakes (leading spaces, wrong or missing model names)
 * shortens model strings (we don't need to use whole model string from dts file, make it for consistency and as optimization)
 * sorts boards alphabetically

in base-files/lib/ramips.sh script.

Case statement was tested after above changes with simple script, which:
 * takes model string from dts{,i} file (model = "...")
 * provides this value as case input ($machine)
 * returns output ($name)

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46632
2015-08-17 06:01:44 +00:00
John Crispin 0d464c360f ramips: remove old code for Edimax BR-6524N
It seems that support for Edimax BR-6524N was dropped long time ago (dts file for this device is missing).
This patch removes remaining code.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46630
2015-08-17 06:01:23 +00:00
John Crispin 2fe5cf2bd6 ramips: fix 7Links PX-4885 dts{, i}, board, image and profile names
The following patch changes 7Links PX-4885 dts{,i} filenames, board, image and profile names from "PX4885" to "PX-4885" (for consistency).

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46629
2015-08-17 06:01:06 +00:00
John Crispin e4b6dcee5e ramips: fix Buffalo WMR-300 dts, board, image and profile names
The following patch changes Buffalo WMR-300 dts filename, board, image and profile names from "WMR300" to "WMR-300" (for consistency).

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46628
2015-08-17 06:00:49 +00:00
John Crispin 713c81e97b ramips: fix Omnima models, images and profiles names
Official names for supported Omnima products are (as on website):
 * Omnima HPM
 * Omnima MiniEMBWiFi
 * Omnima MiniEMBPlug

This patch changes:
 * board names
 * dts filenames
 * profile names
 * image filenames
 * LED names

for Omnima devices, for consistency.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46627
2015-08-17 06:00:11 +00:00
John Crispin 0bb270429d ramips: fix Edimax BR-6425 board name
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46626
2015-08-17 05:59:57 +00:00
John Crispin 633c46a1d4 ramips: fix Olimex models, images and profiles names
Official names for RT5350F based OLinuXino products are "RT5350F-OLinuXino{,-EVB}" as on official manufacturer website.
The following patch:
 * changes board names from "olinuxino-rt5350f{,-evb}" to "rt5350f-olinuxino{,-evb}"
 * changes filenames of dts and profile files
 * changes image filenames

for Olimex RT5350F-OLinuXino{,-EVB} devices.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46623
2015-08-17 05:59:29 +00:00
John Crispin 66f6c9e231 ramips: fix Sitecom WL-341v3 board and image names
The following patch changes:
 * board name from "wl341v3" to "wl-341v3"
 * dts filename
 * LED names in dts file

for Sitecom WL-341v3 device.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46622
2015-08-17 05:59:12 +00:00
John Crispin 102073ca17 ramips: fix Argus ATP-52B board and image names
The following patch:
 * changes board name from "argus-atp52b" to "atp-52b"
 * changes dts filename
 * fixes LED names in dts file and base-files scripts
 * removes manufacturer name from image filename

for Argus ATP-52B device.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46621
2015-08-17 05:58:57 +00:00
John Crispin 7bf1db0dcb ramips: fix UPVEL model names
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46618
2015-08-17 05:58:20 +00:00
John Crispin a0b8c60134 ramips: fix Xiaomi MiWiFi Mini board, image and profile names
The following patch:
 * changes board name from "xiaomi-miwifi-mini" to "miwifi-mini"
 * changes filenames of dts and profile
 * fixes LED names in dts file and base-files scripts
 * removes manufacturer name from image filename

for Xiaomi MiWiFi Mini device.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46617
2015-08-17 05:58:15 +00:00
John Crispin f38db77707 ramips: fix Zbtlink ZBT-WR8305RT board name
There is another Zbtlink board (ZBT-WA05) supported in ramips target, so use the same naming scheme for ZBT-WR8305RT board and its dts file.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46614
2015-08-17 05:57:41 +00:00
John Crispin e04e44a223 ramips: add subtarget for mt7688
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 46473
2015-07-24 09:11:56 +00:00
John Crispin dcae3723fd ramips: add support for STORYLiNK SAP-G3200U3
STORYLiNK SAP-G3200U3 is an AC1200 router based on MT7621AT+MT7602EN+MT7612EN.
It has 128MB DDR3, 8MB NOR FLASH, 5-port Gbps switch and 1x USB 3.0.

The following patch adds support for this device.

Tested and working:
* ethernet
* both WiFi radios
* USB 3.0
* buttons
* ethernet switch and USB diag LEDs
* UART
* GPIOs

Tested and not working:
* LEDs for WiFi radios (connected with WiFi chips, not supported in mt76?)
* failsafe mode (known problem, needs workaround like other MTK based devices)

More information in Wiki: http://wiki.openwrt.org/toh/storylink/sap-g3200u3

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

SVN-Revision: 46454
2015-07-24 09:09:22 +00:00
John Crispin eff79253f2 ramips: add support for Planex MZK-DP150N
This patch add support for Planex MZK-DP150N.
a mini router on the MT7620A SoC with one Ethernet port and a 802.11n 2.4 GHz radio.

Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>

SVN-Revision: 46405
2015-07-17 12:51:08 +00:00
John Crispin b618573815 ramips: adding support for OY-0001 Wireless Router
Adding support for OY-0001 Wireless Router.
OY-0001 is a wireless router made by oyewifi.com. Below is the details:
MT7620A, 128MB DDR2, 16MB FLASH, SD Slot, USB 2.0, 4 x LAN + 1 x WAN.

Signed-off-by: Tom Deng <2579131212@qq.com>

SVN-Revision: 46349
2015-07-14 07:40:22 +00:00
John Crispin 2658b33f68 ramips: a5-v11 board fix power led blinking at boot
Signed-off-by: Konrad Kotowicz <skoti1@go2.pl>

SVN-Revision: 46215
2015-07-07 13:43:37 +00:00
John Crispin cf1fb25e67 ramips: Add Support for the Linksys RE6500
This patch adds support for the Linksys RE6500 Range Extender

http://wiki.openwrt.org/toh/linksys/re6500

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 46043
2015-06-18 18:20:56 +00:00
John Crispin e26ba31f76 ramips: Add support for the D-Link DCS-930 B1
http://wiki.openwrt.org/toh/d-link/dcs-930l

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 46042
2015-06-18 18:20:46 +00:00
John Crispin 640b211b1e ramips: add support for PandoraBox PBR-M1
This patch is for PandoraBox PBR-M1 which is based on mt7621,
all the features work fine, including rtc, leds, button, usb3.0, etc.

Signed-off-by: tymon <banglang.huang@foxmail.com>

SVN-Revision: 46041
2015-06-18 18:20:40 +00:00
Felix Fietkau d5542640d4 ramips: fix Power LED handling for WHR-300HP2, WHR-600D, WHR-1166D
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 45930
2015-06-08 12:51:13 +00:00
John Crispin 0ec720e9a9 ramips: Add support for RT5350F-OLinuXino V2
Version 2 : White spaces and  alphabetical order problems
 fixed
Support for Olimex RT5350F-OLinuXino Boards, tested with RT5350F-OLinuXino and RT5350F-OLinuXino-EVB boards. More Info :
 https://www.olimex.com/Products/OLinuXino/RT5350F/RT5350F-OLinuXino/open-source-hardware

Signed-off-by: Dimitar Gamishev HeHoPMaJIeH <gamishev@gmail.com>

SVN-Revision: 45902
2015-06-05 14:12:25 +00:00
Felix Fietkau 5d6788f773 ramips: extract MAC address on WHR-300HP2, WHR-1166D, WHR-600D
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 45844
2015-05-29 21:42:06 +00:00
Felix Fietkau 8b42d93358 ramips: implement sysupgrade support for whr-300hp2
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 45842
2015-05-29 21:13:28 +00:00
John Crispin 870cd41936 rampis: add support for status led on ASUS RT-N14U
The diag.sh script lacked an entry for the status led on the RT-N14U,
map it to the asus:blue:power led which is also used by the boot loader
to report boot status (eg. TFTP recovery mode VS normal boot)

Signed-off-by: Matteo Panella <m.panella@level28.org>

SVN-Revision: 45725
2015-05-23 15:27:10 +00:00
John Crispin 9c86abae0e ramips: Adding support for AXIMCom MR-102N 3G/4G Travel Mobile Router
MR-102N is a RT3050F based wireless router(32M RAM + 8M NOR flash) with 1 USB
and 1 ethernet port.  The original product information can be found at:
http://www.aximcom.com/en/MR-102N

Signed-off-by:	Tai-hwa Liang <atliang@gmail.com>

SVN-Revision: 45724
2015-05-23 15:27:05 +00:00
John Crispin 5e96c2d541 ramips: add support for Comfast CF-WR800N
This patch adds support for Comfast CF-WR800N, a wall-plug wireless router
based on the MT7620N SoC with one Ethernet port and a 802.11n 2.4 GHz radio.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>

SVN-Revision: 45722
2015-05-23 15:26:39 +00:00
John Crispin b7f19a5b26 ramips: Add support for Microduino MicroWRT
MicroWRT is an wireless router with 2 USB,1 ethernet port. It
has a 16M flash and 64M DDR2 RAM. You can use most interface, such as
i2c, SPI, i2s and PCIe. Besides that there are three expansion borad to
combine with the core board. The detailed information, please refer to
https://www.microduino.cc/wiki/index.php?title=Main_Page

This patch adds support for it.
Because there is only one port,so disabled VLAN and use eth0 as lan
port. and only a power LED control by power pin.

Signed-off-by: 盛凯 <shengkai81@gmail.com>

SVN-Revision: 45331
2015-04-09 10:32:37 +00:00
John Crispin 449c5f7b30 ramips: Add support for ZTE Q7
ZTE Q7 is a wireless router with SD Card,USB,1 ethernet port and a battery.It used MT7620a SoC.
I can,t find any information about this router on ZTE's website.
But I found this : http://en.cctairmobi.com/plus/list.php?tid=40
This router is the same as ZTE Q7 and later I found that both routers are made by the same company:-D

This patch adds support for it.
Because there is only one port,I disabled VLAN and use eth0 as lan port.
I could only create a sysupgrade firmware because I don't know how the orignal webpage check the uploaded image:-(

Signed-off-by: 郭传鈜 <gch981213@gmail.com>

SVN-Revision: 45208
2015-04-01 08:31:46 +00:00
Felix Fietkau 975e1357e6 ramips: fix LAN/WAN MAC address for WSR-600/1166
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 44903
2015-03-20 09:37:07 +00:00
John Crispin 0ba8217008 ramips: nexx wt3020: fix status led
For Nexx WT3020 board_name is wt3020, not nexx-wt3020

root@OpenWrt:~# . /lib/ramips.sh; echo $(ramips_board_name)
wt3020

Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>

SVN-Revision: 44499
2015-02-22 08:28:35 +00:00
John Crispin 3618391514 ramips: Buffalo WZR-AGL300NH target support
I got work with this patch.
Ethernet switch (includes VLAN), WiFi connected via PCIe, LEDs, buttons.

In mtd partion map of DTS file, I renamed Linux firmware regions (kernel + root squashfs) to “firmware”because it allows kernel to split kernel and roots and rootfsdata.

signed-off-by: ngc@ff.iij4u.or.jp
——
——

SVN-Revision: 44470
2015-02-16 21:19:18 +00:00
John Crispin 4ce7053b2b ramips: Kingston MLW221 and MLWG2 cleanup
MLW221 dts use tabs NOT spaces.
MLWG2 dts typo and 1 tab not spaces
01_leds and diag.sh cleanup

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 44356
2015-02-09 12:15:45 +00:00
Luka Perkov 81db848656 targets: base-files: diag.sh does not need to be executable
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 44305
2015-02-07 19:58:58 +00:00
Luka Perkov 92e6e80080 targets: files in uci-defaults do not need to be executables
Signed-off-by: Luka Perkov <luka@openwrt.org>

SVN-Revision: 44304
2015-02-07 19:58:52 +00:00
John Crispin 70db4e4639 ramips: add support for Xiaomi MiWiFi Mini devices
This patch adds support for Xiaomi MiWiFi Mini, a 802.11a/b/g/n/ac dual radio
wireless router based on the MediaTek MT7620a SoC.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>

SVN-Revision: 44238
2015-02-02 09:01:07 +00:00
John Crispin 36d19e46df ramips: add support for Tenda 3G150B
Add suport for Tenda 3G150B:
- cpu: Ralink RT5350F
- flash: 4MB
- ram: 32MB
- 1x USB 2.0
- 1x RJ45
- one reset button
- battery powered (BP-4L, 3.7V 1450mAh)

Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>

SVN-Revision: 44073
2015-01-22 09:35:22 +00:00
John Crispin 607ecb249c ralink: add support for firewrt
this is a mt7621 based board

Signed-off-by: wengbj <linux.c@foxmail.com>

SVN-Revision: 44055
2015-01-20 06:34:28 +00:00
Felix Fietkau 40b740b232 ramips: add preliminary support for DIR-860L B1
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 44016
2015-01-17 21:20:05 +00:00
John Crispin 88df2bd2ff ramips: add support for Intenso Memory 2 Move USB 3.0
This adds support for a rt5350-based "portable nas" solution
from Intenso. The board comes with 32M RAM and 8M Flash, the
built-in HDD is connected/accessible via a usb3.0<->sata
bridge VLI VL701.

The device has 1 Ethernet port (100M/10M), 1 micro b usb 3.0
socket (for charging the battery, or accessing the hdd directly).
Wireless connectivity is provided by the rt5350 SoC [i.e.:
802.11n 1x1 2.4 GHz with a pcb antenna.]

Serial, leds, wifi, ethernet and usb are tested and
as far as I can tell: they are working fine (tm).

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>

SVN-Revision: 44001
2015-01-17 14:06:13 +00:00
John Crispin 7a65864344 ralink: add support for Kingston MLWG2
This patch adds support for the Kingston Mobilelite Wireless G2 (MLWG2)

http://wiki.openwrt.org/toh/kingston/mlwg2

https://github.com/gmacario/kingston-mlwg2-hack/wiki/Testing-OpenWrt-on-MLWG2

Tested-by: Gianpaolo Macario <gmacario@gmail.com>

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 43990
2015-01-17 07:07:36 +00:00
John Crispin 27b82a7990 ramips: fix default led configuration for rt-n14u
use new helper function to generate default led configuration

Signed-off-by: Pavel Löbl <lobl.pavel@gmail.com>

SVN-Revision: 43984
2015-01-17 07:06:51 +00:00
Felix Fietkau 48d8bc4f97 ramips: add preliminary Archer C20i support
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 43898
2015-01-09 15:40:51 +00:00
John Crispin 2120e48e75 ramips: Fix HooToo HT-TM02 support.
- Fix LED definitions.
- Add mode-switch slider definition (at GPIO 14).
- Remove unneeded VLAN now that the ethernet driver is fixed and TCP packets get passed correctly now. (This router only has one port.)
- Fix LAN port MAC address, which is defined in the factory partition as WLAN MAC address + 1.
- Fix board name, as the company name is HooToo and not HOOTOO.
- Remove unnecessary packages from the profile. (The end-user is supposed to use mechanisms such as the ImageBuilder in order to add his own set of packages to his own images... while the precompiled images should just contain the core set of packages needed to run the base functions of a wireless router.)

Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>

SVN-Revision: 43883
2015-01-08 20:26:20 +00:00
John Crispin 2ea64717e2 ramips: update BR-6475ND dts
Update firmware location for 2.4GHz radio on the Edimax BR-6475nD.

Signed-off-by: Christopher Lais <chris+openwrt@zenthought.org>

SVN-Revision: 43881
2015-01-08 20:26:02 +00:00
John Crispin f9dcd95919 ramips: base-files: Whitespace fixes.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>

SVN-Revision: 43880
2015-01-08 20:25:55 +00:00
Felix Fietkau ada0452b14 ramips: fix WSR-{600,1166} names
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 43817
2015-01-03 18:31:11 +00:00
Felix Fietkau ca32b89cc0 ramips: fix wsr-1166 sysupgrade support
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 43816
2015-01-03 18:31:06 +00:00
John Crispin 019ea725aa add "preinit_regular" diag.sh set_state argument
This new argument is used right after starting regular preinit (which
happens if failsafe wasn't triggered). The main purpose of "preinit"
argument is to indicate that failsafe can be triggered, however we were
missing a way to inform user that we don't wait for a trigger anymore.
With this change it's clear when failsafe mode can be triggered.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>

SVN-Revision: 43715
2014-12-15 10:37:00 +00:00
John Crispin 263070a2e7 ramips:Add support for Aigale Ai-BR100
Aigale Ai-BR100 is a router with mt7620a soc.
There are only 2 lights on the board (WAN and WLAN) so I used the wlan light as the status led.

Signed-off-by: 郭传鈜 <gch981213@gmail.com>

SVN-Revision: 43681
2014-12-13 08:07:03 +00:00
John Crispin 6c4e7b22eb ralink: fix lenovo y1 wan port mapping
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 43667
2014-12-12 16:17:31 +00:00
Felix Fietkau 02c319c27a ramips: fix default config breakage on whr-1166d
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 43281
2014-11-16 11:39:19 +00:00
John Crispin 0371dabc13 ralink: add support for WSR-600/1166
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 43244
2014-11-14 16:52:36 +00:00
John Crispin bfcdc8711c ralink: fix up dts for mt7621 eval board
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 43238
2014-11-12 14:55:00 +00:00
Felix Fietkau 07754ac297 ramips: enable sysupgrade for whr-600d, whr-1166d
Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 43213
2014-11-08 12:18:58 +00:00
John Crispin cadf517107 ralink: add support for mt7628
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 43197
2014-11-06 09:31:31 +00:00
Imre Kaloz d738d22bf8 add support for the Linksys E1700
SVN-Revision: 43186
2014-11-05 14:37:13 +00:00
John Crispin cc142739f2 ralink: fix wan port on whr-1166
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 43171
2014-11-03 20:20:40 +00:00
John Crispin cc5194cf03 ramips: add support for Airlink101 AR670W
This is a RT2880-based board, 32MB RAM, 4MB flash. The bootloader
is a hacked u-Boot that reads an LZMA image directly, so we skip
generating the uImage header and enable the lzma mtdsplit parser.

Signed-off-by: Claudio Leite <leitec@staticky.com>

SVN-Revision: 43153
2014-11-03 08:00:13 +00:00
John Crispin 0b64dca49d ralink: load mt7530 driver on the 3 buffalo units
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 43119
2014-10-30 10:10:51 +00:00
John Crispin c0bf47232a ralink: fix switch config on mt7530 evb
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 43105
2014-10-29 18:51:02 +00:00
John Crispin d0bf15f235 ramips: add support for A5-V11 board (resubmit)
(Reposted due to an issue with the patchwork server during original submission)

Unbranded. Silkscreen on PCB is “A5-V11”, believed to be made by Bococom (or at least uses Bococom image encryption - as used on poray devices - but different key)

Signed-off-by: Gareth Bryan <gareth@mx9.org>

SVN-Revision: 43102
2014-10-29 11:01:17 +00:00
John Crispin 7bac455a4c ramips: add support for Nexx WT3020 devices
SVN-Revision: 42983
2014-10-20 06:28:48 +00:00
John Crispin 5b40a150ea ramips: sort boards in upgrade/platform.sh alphabetically
SVN-Revision: 42982
2014-10-20 06:28:39 +00:00
John Crispin 20940138ac scripts: fix wrong usage of '==' operator
[base-files] shell-scripting: fix wrong usage of '==' operator

normally the '==' is used for invoking a regex parser and is a bashism.
all of the fixes just want to compare a string. the used busybox-ash
will silently "ignore" this mistake, but make it portable/clean at least.

this patch does not change the behavior/logic of the scripts.

Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>

SVN-Revision: 42911
2014-10-14 12:21:11 +00:00
John Crispin af1207b58c ramips: add support for Nexx WT1520
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>

SVN-Revision: 42867
2014-10-10 08:56:43 +00:00
John Crispin d76b7e0221 ramips: D-Link DIR-810L: make led naming consistent with other boards
Signed-off-by: Michael Heimpold <mhei@heimpold.de>

SVN-Revision: 42789
2014-10-06 04:52:36 +00:00
John Crispin b04bb3eea7 ramips: Support for RAMIPS based Tripmate HT-TM02 board
Provides support for the Tripmate HT-TM02 personal router including LEDs and
reset button. “Mode” switch is not supported. New profile includes full set
of packages required to enable LEDs, USB, and LUCI. Patches were applied
against trunk snapshot r42649. Functionality has been tested in AP, basic wifi
client, wifi router, and routed client modes - all good.

Signed-off-by: Ron Curry <wingspinner@gmail.com>

SVN-Revision: 42785
2014-10-06 04:52:07 +00:00
John Crispin d4cc995c53 ramips: D-Link DIR-810L. Add support for SoC 2.4 GHz wireless and fix leds naming
SVN-Revision: 42619
2014-09-19 11:07:08 +00:00
John Crispin ff3ea02772 ramips: add omni plug leds
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 42201
2014-08-18 16:09:21 +00:00
John Crispin d04cab8dfc ramips: Add support for Omnima MiniPlug
This patch adds support for the Omnima MiniPlug RT5350 based board, 8MB SPI flash

Signed-off-by: Ivan Ignjatic<ivan@omnima.co.uk>

SVN-Revision: 42200
2014-08-18 16:06:48 +00:00
John Crispin be6bbc7975 ramips: fix switch config for Edimax 3G-6200n
Switch in Edimax 3G-6200n also require full switch reset, not only vlan definitions. Tested on Edimax 3G-6200n.

Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>

SVN-Revision: 42194
2014-08-18 13:10:04 +00:00
John Crispin bb9a23aca2 ramips: Hame: change LED name mpr-x -> hame
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>

SVN-Revision: 42190
2014-08-18 13:09:39 +00:00
John Crispin 0fc4383d69 ramips: make use of the new board detection layer
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 42186
2014-08-18 13:09:20 +00:00
John Crispin 3a9752bbd2 ramips: add a workaround to fix failsafe on RT5350
Due to TCP connections not working when VLAN is disabled, this is
needed to get failsafe functional.

Signed-off-by: Paul Fertser <fercerpav@gmail.com>

SVN-Revision: 42179
2014-08-18 13:08:52 +00:00
John Crispin 04e4ff282a ramips:support Lenovo AC1200 Wireless router
Lenovo AC1200 series has two types, Y1 and Y1S.
Y1S has 256MB DDR2, Y1 only has 128MB and Y1 have no Giga Port.

Signed-off-by: Lintel <lintel.huang@gmail.com>

SVN-Revision: 41961
2014-08-03 11:13:52 +00:00
John Crispin 21845cb45d ramips: Add support for VoCore
This is based and tested on VoCore Alpha, but other stuff like status/eth LEDs are present on the final board revision + VoDock.
All GPIOs are exported, except spi/i2c.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>

SVN-Revision: 41939
2014-08-01 20:51:24 +00:00
John Crispin 9efd7ebd34 ramips: add support for easyacc wizard8800
Signed-off-by: Sebastian Wendel <s.wendel@sourceindex.de>

SVN-Revision: 41936
2014-08-01 11:19:50 +00:00
John Crispin c6674722b9 ramips: Fix LEDs on the Kingston MLW221
LED Fix up for the Kingston Mobilelite Wireless (MLW-221)

http://wiki.openwrt.org/toh/kingston/mlw221

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 41933
2014-08-01 11:19:39 +00:00
John Crispin 5b4abf87d7 ramips: add support for Kingston MLW221
This patch adds support for the Kingston Mobilelite Wireless (MLW-221)

http://wiki.openwrt.org/toh/kingston/mlw221

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 41841
2014-07-26 20:36:22 +00:00
John Crispin b77e92e020 ramips: ethernet mac cleanup
Compile tested all subtargets and profiles.
Unfortunately I don't own any board affected by these changes, so no run tests.

Signed-off-by: Roman Yeryomin <roman@advem.lv>

SVN-Revision: 41839
2014-07-26 20:36:09 +00:00
John Crispin 443aee86bf ramips: fix vlan configuration for asiarf avm003
The earlier r41797 change was missing this part, to enable the right
vlan configuration.

Signed-off-by: Russell Senior <russell@personaltelco.net>

SVN-Revision: 41838
2014-07-26 20:36:01 +00:00
John Crispin 08fb5fb326 ramips: fix sysupgrade for asiarf awm003
Since the earlier r41797 change, the board_name for awm003 has been
miscalculated, and sysupgrade has been broken.  This seems to fix it.

Signed-off-by: Russell Senior <russell@personaltelco.net>

SVN-Revision: 41837
2014-07-26 20:35:46 +00:00
John Crispin e5d4e5dee3 ramips: fix missing inclusion of system.sh for mtd_get_mac_binary and friends.
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>

SVN-Revision: 41810
2014-07-23 07:49:50 +00:00
John Crispin f44d3f9980 ramips: soc wmac eeprom cleanup
Move eeprom extraction from scripts to dts files.
Additionally there are few other changes like:
- whitespace fixes
- add partition labels where needed
- BR6524N board doesn't exist (lost in translation?)
- fix Edimax 3g-6200nl model
- add wmac eeprom to dts for Asus RT-N14U board

Compile tested all subtargets and their profiles.
Run tested on:
- Asus RT-N15
- Asus RT-N14U
- Buffalo WHR-600D
- Argus ATP52B
- Sparklan WCR-150GN

Few problems noted:
- many boards didn't have wmac eeprom information defined at all
- several boards don't have any patitions defined (see FIXME comments in dts)

Signed-off-by: Roman Yeryomin <roman@advem.lv>

SVN-Revision: 41680
2014-07-17 10:55:31 +00:00
John Crispin 74db9511dc ramips: basic support for Planex MZK-750DHP
some gpios are still missing.

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41654
2014-07-14 17:10:39 +00:00
John Crispin 4af1b51ec3 ramips: extract default lan_mac from eth0
The default case of ramips_setup_macs() is useful when mtd-mac-address is defined in dts.
But lan_mac is not set by default, this results in lan and wan having the same mac.

Signed-off-by: Roman Yeryomin <roman@advem.lv>

SVN-Revision: 41632
2014-07-14 07:38:23 +00:00
John Crispin ba3988fb16 ramips: add support for WR8305RT board
Signed-off-by: Jorge Vargas <jorge.vargas@sosvia.com>
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41584
2014-07-12 06:54:03 +00:00
John Crispin 03faf4618e ramips: add support for Zbtlink WA05 router
Signed-off-by: Roman Yeryomin <roman@advem.lv>

SVN-Revision: 41579
2014-07-10 22:02:28 +00:00
John Crispin 3d81a4ef82 ralink: add Wansview NCS601W IP Camera
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41453
2014-07-02 07:42:44 +00:00
John Crispin c749b310ed ralink: register wifi firmware for WRTnode
After r41444 wifi working on WRTnode. Tested.

Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41452
2014-07-01 18:17:55 +00:00
John Crispin 4ddc0f9ff3 ramips: add WHR-1166 support
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41447
2014-07-01 10:26:42 +00:00
John Crispin dc5fe5f73f ramips: RT-N56U support fixes and factory image creation
Signed-off-by: Mikko Hissa <mikko.hissa@werzek.com>

SVN-Revision: 41224
2014-06-16 18:57:20 +00:00
John Crispin 2fe435081d ramips: add vlan configuration for asiarf awm002-evb
Without this, the ports all end up on vlan 1.  This enables a separate
WAN port that works.

Signed-off-by: Russell Senior <russell@personaltelco.net>

SVN-Revision: 41216
2014-06-16 18:54:48 +00:00
John Crispin 6d213a644d ramips: add asiarf awapn2403 support
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 41177
2014-06-13 09:16:15 +00:00
John Crispin 3306a4f9ab ralink: fix asiarf/awm002 switch setup
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 40939
2014-06-02 12:44:57 +00:00
John Crispin f933a741a9 target/linux/*/base-files/lib/upgrade/platform.sh - wrong check for ARGC
ARGC is a 'C-ism', but not known/valid in shell-syntax - insert the correct
var $# (=number of args) here. under normal conditions this had no impact,
but we should at least correct it. the error was observable like this:

root@box:~ [ -e "/etc/functions.sh" ] && . /etc/functions.sh
root@box:~ [ -e "/lib/functions.sh" ] && . /lib/functions.sh
root@box:~ . /lib/upgrade/platform.sh
root@box:~ . /lib/upgrade/common.sh
root@box:~ platform_check_image /tmp/myfirmware.bin
ash: bad number
root@box:~ echo $?
0

Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>

SVN-Revision: 40915
2014-06-02 12:43:22 +00:00
John Crispin 9b728bebfb ramips: fix not set lan/wan mac address
The first switch case is default case. Then it will only
match default case. cause not update the lan/wan mac address.
And in the default switch case the param lan_mac is empty.
it will case error message 'arithmetic syntax error' when
call macaddr_add function.

Signed-off-by: michael lee <igvtee@gmail.com>

SVN-Revision: 40910
2014-06-02 12:43:04 +00:00
John Crispin 813a7c3827 ralink: Add support for samsung cy-swr1100 wireless router
It is base on rt3662 soc with dual band 802.11n
wireless router. Use rtl8367R switch chip.
This patch adds a profile for this board.
It use seama image header. so i also enable it
on kernel config.

Signed-off-by: michael lee <igvtee@gmail.com>

SVN-Revision: 40908
2014-06-02 12:42:52 +00:00
John Crispin efd09832fe ramips: Support for Teltonika RUT5XX
Hi Hartmut,

Thanks for your feedback, I have reformated the patch accordingly.

Added support for Teltonika RUT5XX hardware.

Signed-off-by: Steffen Weinreich <steve@weinreich.org>

SVN-Revision: 40907
2014-06-02 12:42:48 +00:00
John Crispin 4a7a0d2536 ralink: add dir-645 to the eeprom hotplug script
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 40561
2014-04-23 07:52:56 +00:00
John Crispin cd5f3584e2 ramips: Add support for the 7Links PX-4885 wireless router.
The 7Links PX-4885 is a small battery-powered wireless router.
It is based on a RT5350F WiSoC and features one ethernet port and one
USB port. It is a Hame MPR-A1 clone, except it has different GPIOs,
a different battery and more RAM (32 MB).
This patch adds a profile for this board, the corresponding device tree
file and the adequate base-files changes (incl. sysupgrade).

Signed-off-by: Hugo Grostabussiat <bonstra@bonstra.fr.eu.org>

SVN-Revision: 40554
2014-04-22 08:08:51 +00:00
John Crispin cb91087991 ramips: add Airlink101 AR725W userland support
Signed-off-by: Claudio Leite <leitec@staticky.com>

SVN-Revision: 40550
2014-04-22 08:08:35 +00:00
John Crispin 96fa58bafd ralink: add support for wrtnode
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 39786
2014-03-07 09:54:59 +00:00
John Crispin b56bef28d7 ralink: add support for na930
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 39611
2014-02-18 13:33:25 +00:00
John Crispin beb29461ff ramips: Add userspace support for the Edimax BR-6475nD
The rt2x00 wifi driver may still need updating to
function with this device.

Signed-off-by: Christopher Lais <chris+openwrt@zenthought.org>

SVN-Revision: 39298
2014-01-15 18:29:44 +00:00
John Crispin 03ef20ce6f ralink: fix eeprom loading
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 39245
2014-01-12 14:03:15 +00:00
John Crispin 3a64ddd0a1 ralink: add HLK-RM04 support
https://github.com/JiapengLi/OpenWrt-HiLink-HLK-RM04

Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 39237
2014-01-12 12:07:40 +00:00
John Crispin aa2be01076 ralink: switch to askconsole
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 39236
2014-01-12 12:07:34 +00:00
John Crispin 9739a0b41b ramips: add support for RT-N14U (mt7620n based) board
added dts file and userspace scripts modified to support Asus RT-N14U board

current support status:
usb        works
ethernet   works
buttons    reset, wps
leds       asus:blue:[usb|lan|wan|air|power]
i2c        not tested
uart       not tested
wifi       not yet

Signed-off-by: Pavel Löbl <lobl.pavel@gmail.com>

SVN-Revision: 39163
2013-12-25 17:04:50 +00:00
John Crispin 2370126b9b ramips: Fix initial network configuration for few boards
Argus ATP52B:      ethernet didn't work because of unconfigured switch
Sparklan WCR150GN: add switch config and make single port to be LAN
Dlink DIR-645:     seems to be a redundant case

Signed-off-by: Roman Yeryomin <roman@advem.lv>

SVN-Revision: 38960
2013-11-30 08:36:56 +00:00
John Crispin 93e9a71538 base-files: allow users to delect debug level during boot
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 38909
2013-11-25 08:34:55 +00:00
John Crispin 5b437e204f ralink: set the mac addr via the dts file
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 38902
2013-11-25 08:33:42 +00:00
John Crispin d175740783 ralink: set wmr-300 mac properly
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 38872
2013-11-19 21:13:24 +00:00
John Crispin 82e6242798 ralink: add support for ralink mt7620 nand eval board
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 38848
2013-11-18 09:35:41 +00:00
John Crispin 9d4eb0ac91 ralink: make all none 3x5x boards default to a vlan1/2 setup
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 38845
2013-11-18 09:35:14 +00:00
John Crispin 5c2e867460 ramips: fix wmr300 network detection
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 38828
2013-11-17 13:14:46 +00:00
John Crispin dce9b292bf ralink: add mt7620n support
Signed-off-by: John Crispin <blogic@openwrt.org>

SVN-Revision: 38823
2013-11-16 20:28:52 +00:00