I have not found a scenario that would break by setting the source address on
default, but please let me know if any special considerations should be taken.
Signed-off-by: Kristian Evensen <kristian.evensen at gmail.com>
SVN-Revision: 43582
if the initramfs kernel and payload were flashed in one block, the payload might not be at the start of the ubi partition due to bad blocks inside the kernel partition.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43513
KD20 got an IC+ phy, without the driver the phy is not properly
initialized resulting in ethernet not working unless being already
initialized by the vendor loader.
upstream commit 368b4d2b49bbbf379d9334747fbbd2aaaafe4356
drivers: net: remove dead drivers
removed icplus.c due to the lack of in-tree users.
Partially revert that commit adding back the IC+ driver.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43508
it is now possible to flash a initramfs kernel and a sysupgrade tar file inside the ubi partition. on first boot, the takeover script will find the tar file, extract and finally sysupgrade it. this allows us to flash owrt/ubi images in a 2 phase setup using ODM webuis that are not ubi aware. this is needed by some mediatek and brokencom devices.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43505
this can be used on nand flashes and will skip bad blocks and run ecc on the
read data before dumping it.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43500
Added complementary blobmsg_close_table() before returning from function
on error.
Signed-off-by: Sławomir Demeszko <s.demeszko@wireless-instruments.com>
SVN-Revision: 43477
In r41872 and r42787 Dynamic VLAN support was reintroduced, but the vlan_bridge
parameter is not read while setting up the config, so the default is used which
is undesirable for some uses.
Signed-off-by: Ben Franske <ben.mm@franske.com>
SVN-Revision: 43473
create user:group before running postinst-pkg. the postinst hook might require
the user:group to already exist.
Signed-off-by: Christian Schoenebeck <christian.schoenebeck@gmail.com>
SVN-Revision: 43472
Packages fdisk and lsblk were missing dependency for libsmartcols.so.1
Add package for libsmartcols and add dependency from fdisk and lsblk.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43459
perf was in the oldpackages repository, but it makes more sense to have
it part of the default package set since we build it from the Linux
kernel sources.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 43418
Thanks to Dave Taht for debugging and thanks to Comcast for
shipping strangely behaving software so I can fix some corner cases.
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 43415
fixes BeagleBoard C4 detection
error message in serial console was:
"WARNING: Could not determine device tree to use"
change is found in upstream u-boot
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 43392
This adds support for the oxnas target in U-Boot 2014.04
History can be found at https://github.com/kref/u-boot-oxnas up to 2013.10
changes from 2013.10 to 2014.04 can be followed at
https://gitorious.org/openwrt-oxnas
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43389
This is the oxnas target previously developed at
http://gitorious.org/openwrt-oxnas
Basically, this consolidates the changes and addtionas from
http://github.org/kref/linux-oxnas
into a new OpenWrt hardware target 'oxnas' adding support for
PLX Technology NAS7820/NAS7821/NAS7825/...
formally known as
Oxford Semiconductor OXE810SE/OXE815/OX820/...
For now there are 4 supported boards:
Cloud Engines Pogoplug V3 (without PCIe)
fully supported
Cloud Engines Pogoplug Pro (with PCIe)
fully supported
MitraStar STG-212
aka ZyXEL NSA-212,
aka Medion Akoya P89625 / P89636 / P89626 / P89630,
aka Medion MD 86407 / MD 86805 / MD 86517 / MD 86587
fully supported, see http://wiki.openwrt.org/toh/medion/md86587
Shuttle KD-20
partially supported (S-ATA driver lacks support for 2nd port)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43388
mtd.c:544:7: warning: format ‘%x’ expects argument of type ‘unsigned int’, but argument 3 has type ‘ssize_t’ [-Wformat]
mtd.c:602:1: warning: label ‘done’ defined but not used [-Wunused-label]
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43383
1) nand_upgrade_tar: use a simpler condition that matches if () { }
logic and fix check of $kernel_length variable
2) nand_do_upgrade_stage2: use case, otherwise one could believe we
always call nand_upgrade_tar
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 43373
r37490 removed the actual driver but left the kmod definition intact,
causing the build system hapily creating an empty package for it.
Remove it also to not make it seem as if it still exists.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 43316
ldd might be called for shell scrips during sysupgrade, causing it to
complain that they are not a dynamic executables.
This is a harmless error, so supress it to avoid confusing about them
being serious ones.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 43315
ld-musl-*.so* is a symlink "broken" for the hostsystem, so wildcard
will skip it, causing LD_MUSL_NAME to empty and the ldd symlink pointing
to ../../lib directly.
This causes sysupgrade failing to copy any linked libaries and
consequently failing to run anything after switching to ram disk.
Fix this by creating a symlink directly pointing to where ld-musl-*.so*
points to.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 43314
Update nf_conntrack_rtsp to latest version based on http://mike.it-loops.com/rtsp/ (rtsp-module-3.7-v2.tar.gz).
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 43311
* fixes a bug in multipart sms
* adds a new call to read the sim phone number (partially functioanl)
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43310
r36107 ("base-files: sysupgrade fail with eglibc") tried to fix
sysupgrade by changing the ld-soname to what is expected, but only
fixed MIPS while breaking ARM.
The underlying issue is that the ld.so name varies widely across
different architectures for eglibc:
eglibc-2.19-r25243$ grep -r "ld-soname :=" . | awk '{ print $3 }' | sort -u
ld64.so.1
ld64.so.2
ld-linux-aarch64_be.so.1
ld-linux-aarch64.so.1
ld-linux-armhf.so.3
ld-linux-mipsn8.so.1
ld-linux.so.2
ld-linux.so.3
ld-linux-x32.so.2
ld-linux-x86-64.so.2
ld.so.1
Instead of adding each different soname to check for and copy it,
replace the awk script with a sed script to extract it properly and
drop the hardcoded so-name.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 43295
Starting from kernel version 3.15, the crc32c module was renamed to
crc32c_generic.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43291
usb-common.ko was moved to drivers/usb/common starting from kernel 3.16
by upstream commit f4cbd33fd5f0587910fa9db403a1b42f1cabf820
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43290
b52053b 6in4: https support for he.net tunnel api
introduced HTTPS support using wget.
The busybox version of wget, however, doesn't support the -V option,
thus poluting logfiles with a full invalid-parameter-output.
Redirect stderr to fix that.
As libcurl and curl support selecting the SSL library of your choice,
also add support for curl which is more commonly used on OpenWrt than
"real" wget which needs libopenssl.
Also make sure to respect SSL_CERT_DIR and increase timeouts.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43228
setsid is called fixing the pgrp issue
trigger the wdt while modules are being inserted
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 43193
This will ease adding new targets and updating:
* split UBOOTS var into multiple lines
* remove version from TITLE
Signed-off-by: Nicolas Thill <nico@openwrt.org>
SVN-Revision: 43187
This patch adds the userspace and kernelspace for
- match NETFILTER_XT_MATCH_CLUSTER
This match can be used to deploy gateway and back-end load-sharing clusters.
- target IP_NF_TARGET_CLUSTERIP
This module allows you to configure a simple cluster of nodes
that share a certain IP and MAC address
without an explicit load balancer in front of them.
Connections are statically distributed between the nodes in this cluster.
This is used i.e. by strongswan-ha.
Signed-off-by: Christian Scheele <cs@embedd.com>
SVN-Revision: 43174
Generate a random serial from /dev/urandom when creating selfsigned certs.
Fixes "sec_error_reused_issuer_and_serial" with Firefox.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 43168
Note, that licensing stuff is a nightmare: many packages does not clearly
state their licenses, and often multiple source files are simply copied
together - each with different licensing information in the file headers.
I tried hard to ensure, that the license information extracted into the OpenWRT's
makefiles fit the "spirit" of the packages, e.g. such small packages which
come without a dedicated source archive "inherites" the OpenWRT's own license
in my opinion.
However, I can not garantee that I always picked the correct information
and/or did not miss license information.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
SVN-Revision: 43155
Port Debians adaptive LCP echo patch to pppd, make it configurable with UCI
and enable it by default.
When adaptive LCP echo is enabled, LCP echo requests are only sent if the
link is idle, this avoids the common situation where a congested PPP link
(e.g. during torrenting) is falsely detected as disconnected because the
LCP replies are not received in time.
Also bump the copyright year in the Makefile, remove a redundant maintainer
entry and fix the shell processing of the keepalive option when the two-
value syntax is used.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 43143
Only list the kernel versions that do not match so that new kernel
versions will automatically match. This improves support for kernel
3.18.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 43132
This patch added stuff that is already there and if it would be needed
this would result in a compile error.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 43131
More recent kernel versions (>= 3.12) support native VXLAN
support.
The Open VSwitch kernel module tries to build using native VXLAN
support if it detects a kernel version >=3.12.
The build works fine, but during startup the OVS kernel module
does not load.
dmesg output is something like this:
[ 1201.262842] openvswitch: Unknown symbol vxlan_sock_release
[ 1201.262949] openvswitch: Unknown symbol vxlan_xmit_skb
[ 1201.263161] openvswitch: Unknown symbol vxlan_sock_add
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
SVN-Revision: 43126
Using a redirect to a non-empty mtd partition will not erase the
blocks prior to writing to them resulting in broken dsl_fw.
Fix this by piping to mtd write - /dev/mtdX instead.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43125
HE.net tunnel update API requests are now made via https if an
SSL-capable wget is installed. Certificate validation is
conditionally enabled if the CA certs are available.
Signed-off-by: Andrew Skalski <askalski@gmail.com>
SVN-Revision: 43124
I had to use a VDSL-only tone-setup to get show-time.
Handle this in uci by checking if annex is unset.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43114
The DHT11 is a temperature and humidity sensor supported by linux
since 3.14.
This patch is tested on recent mxs with kernel 3.14.18.
Signed-off-by: Harald Geyer <harald@ccbib.org>
SVN-Revision: 43103
Currently busybox utils like "ls" fail to display filenames containing UTF-8
characters, replacing any special characters with "?".
Change libbb's printable_string() function to allow high ASCII characters so
that unicode filenames are displayed correctls.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 43084
* Fixes sending an extraneous message body for 204 and 304 resoponses which
breaks Chrome in keep-alive mode.
* Adds mimetypes for JSON and JSONP.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 43078
Package util-linux-dmesg is broken (at least) in Barrier Breaker git repo
as you can select it within menuconfig, it will compile (as a part of
util-linux) but it will not install as install section is missing from
package Makefile.
Signed-off-by: Tomasz Wasiak <tjwasiak@gmail.com>
SVN-Revision: 43069
- Support HT40 instead of HT40+/HT40- like mac80211
- Enable 11n if htmode is HT20 or HT40
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 43063
Based on bug #18206 sysupgrade can lead to loss of password information in
certain situations. Most likely all users who will upgrade from versions
r43017-43040, will lose their current passwords. :-(
https://dev.openwrt.org/ticket/18206
Currently /etc/shadow is defined as a conffile in base-files:
https://dev.openwrt.org/browser/trunk/package/base-files/Makefile#L37
But it is not defined in the default list of essential files to keep in
sysupgrade:
https://dev.openwrt.org/browser/trunk/package/base-files/files/lib/upgrade/keep.d/base-files-essential
If exporting conffiles info fails, /etc/shadow can get lost.
Shadow passwords are now the default, so saying that preserving /etc/passwd
is essential while /etc/shadow is not, makes no sense.
The attached patch adds /etc/shadow to the list of essential files.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
SVN-Revision: 43061
Attempting to build broadcom_wl (from trunk) with the linaro 4.9.x
toolchain produces the following errors:
<...>/wl_linux.c: In function 'wl_dump_ver':
<...>/wl_linux.c:2302:3: error: macro "__DATE__" might prevent reproducible builds [-Werror=date-time]
__DATE__, __TIME__, EPI_VERSION_STR);
^
<...>/wl_linux.c:2302:13: error: macro "__TIME__" might prevent reproducible builds [-Werror=date-time]
__DATE__, __TIME__, EPI_VERSION_STR);
^
cc1: some warnings being treated as errors
Remove the use of the __DATE__ and __TIME__ macros, as the info is not
really useful.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
SVN-Revision: 43046
This module is required to read the CPU core temperature sensors
on the Alix APU board.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 43027
The wpa_psk_file option offers the possibility to use a different WPA-PSK key for each client. The directive points to a file with the following syntax:
mac_address wpa_passphrase_or_hex_key
Example:
00:11:22:33:44:55 passphrase_for_client_1
00:11:22:33:44:67 passphrase_for_client_2
00:11:22:33:44:89 0123456789abcdef0123456789abcdef0123456789abcdef0123456789abcdef
So it is possible to specify both ASCII passphrases and raw 64-chars hex keys.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 43001
[base-files] failsafe-mode: print short help on commandline
Like mentioned in ticket https://dev.openwrt.org/ticket/11911
this should make the IRC much quieter. Failsafe is somehow
special and even experienced users are helpless, because they
are not used to this seldom situation. Also: likely you have
no internet access in this mode, so you cannot use the wiki.
a failsafe-session now looks like this:
first we see from 'package/base-files/files/bin/login.sh' the hint:
=== IMPORTANT ============================
Use 'passwd' to set your login password
this will disable telnet and enable SSH
------------------------------------------
after this the /etc/banner ("OpenWrt - wireless freedom")
and then the new text:
================= FAILSAFE MODE active ================
special commands:
* firstboot reset settings to factory defaults
* mount_root mount root-partition with config files
after mount_root:
* passwd change root's password
* /etc/config directory with config files
for more help see:
http://wiki.openwrt.org/doc/howto/generic.failsafe
=======================================================
this supersedes the old patches:
http://patchwork.openwrt.org/patch/3337/http://patchwork.openwrt.org/patch/3553/
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
SVN-Revision: 42985
Luka Perkov
Steven Barth
Felix Fietkau
John Crispin
Rafał Miłecki
Florian Fainelli
Imre Kaloz
Jonas Gorski
Matteo Croce
Jo-Philipp Wich
Nicolas Thill
Hauke Mehrtens