0fb1c2d537
bcm63xx: Accept any led with power in its name as power led
...
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 26875
2011-05-11 13:33:45 +00:00
c6af9c23b7
bcm63xx: Decouple Board ID and image name for fixup
...
Make the fixup board ID independent from the image name to allow using
the same board ID for similar devices.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 26874
2011-05-11 13:33:41 +00:00
4ea316216a
switch to 2.6.38
...
SVN-Revision: 26873
2011-05-11 13:33:34 +00:00
3fc33726a5
add missing 2.6.38 touchscreen config symbols
...
SVN-Revision: 26872
2011-05-11 13:33:30 +00:00
44eab3f6c1
package/kernel/modules/other.mk is getting big enough that putting the LEDs stuff into its own file makes sense.
...
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
SVN-Revision: 26868
2011-05-09 20:28:04 +00:00
60c125b8e6
(respin) 802.1Q VLAN support for ADM6996M/ADM6996FC
...
This patch adds 802.1Q VLAN support for the ADM6996M chip.
The driver is loaded for both the FC and M model. It will detect which of the
two chips is connected. The FC model is initialised, but no further
functionality is offered.
The PHY driver will always report "100 Mbit/s, link up", for both the M and FC
models. This reflects the fact that the link between switch chip and Ethernet
MAC is always on[1].
Further documentation can be found in the kernel's
Documentation/networking/adm6996.txt
Signed-of-By: Peter Lebbing <peter@digitalbrains.com>
SVN-Revision: 26865
2011-05-09 15:21:58 +00:00
9b5036a29d
ar71xx: populate LED3 on the JA76PF board
...
Patch-by: Cezary Jackiewicz <cezary@eko.one.pl>
SVN-Revision: 26862
2011-05-08 21:38:51 +00:00
b39eebdf1e
ar71xx: add uci config for the WLAN LED on the WRT160NL
...
Based on a patch by Magyar Szabolcs <mszabi@freemail.hu>
SVN-Revision: 26861
2011-05-08 21:38:49 +00:00
858e2e719b
ar71xx: use phy0tpt trigger for the WLAN LEDs
...
SVN-Revision: 26860
2011-05-08 21:38:48 +00:00
869f3cb718
ar71xx: remove superfluous fifo_cfg overrides
...
SVN-Revision: 26859
2011-05-08 21:38:46 +00:00
bc121d5706
ipv6: restore correct ECN handling on TCP xmit Thanks Dave Taht
...
SVN-Revision: 26858
2011-05-08 17:08:06 +00:00
eb4109ba78
Deployment of IPv6 has opened up many more prefixes than just the 2000::/3 space, so a default route of ::/0 is more correct. Thanks Dave Taht
...
SVN-Revision: 26857
2011-05-08 17:03:07 +00:00
5d77f370d6
ar71xx: ag71xx: make switch register access atomic
...
Reading of the PHY registers occasionally returns with bogus values
under heavy load. This misleads the PHY driver and thus causes false
link/speed change notifications which leads to performance loss.
This is easily noticable during an iperf session:
...
[ 3] 52.0-53.0 sec 11.3 MBytes 94.4 Mbits/sec
[ 3] 53.0-54.0 sec 11.4 MBytes 95.4 Mbits/sec
eth1: link down
br-lan: port 2(eth1) entering forwarding state
eth1: link up (100Mbps/Full duplex)
br-lan: port 2(eth1) entering forwarding state
br-lan: port 2(eth1) entering forwarding state
[ 3] 54.0-55.0 sec 6.75 MBytes 56.6 Mbits/sec
[ 3] 55.0-56.0 sec 0.00 Bytes 0.00 bits/sec
[ 3] 56.0-57.0 sec 10.5 MBytes 88.1 Mbits/sec
...
[ 3] 169.0-170.0 sec 11.4 MBytes 95.4 Mbits/sec
[ 3] 170.0-171.0 sec 11.4 MBytes 95.4 Mbits/sec
eth1: link up (10Mbps/Half duplex)
[ 3] 171.0-172.0 sec 7.63 MBytes 64.0 Mbits/sec
[ 3] 172.0-173.0 sec 9.38 MBytes 78.6 Mbits/sec
eth1: link up (100Mbps/Full duplex)
[ 3] 173.0-174.0 sec 11.3 MBytes 94.4 Mbits/sec
[ 3] 174.0-175.0 sec 11.4 MBytes 95.4 Mbits/sec
SVN-Revision: 26856
2011-05-08 16:32:53 +00:00
3711658281
ar71xx: ag71xx: fix section mismatch warnings
...
The function __devinit ag71xx_probe() references
a function __devexit ag71xx_phy_disconnect().
This is often seen when error handling in the init function
uses functionality in the exit path.
The fix is often to remove the __devexit annotation of
ag71xx_phy_disconnect() so it may be used outside an exit section.
The function ag71xx_phy_disconnect() references a function in an exit
section.
Often the function ag71xx_ar7240_cleanup() has valid usage outside the
exit section
and the fix is to remove the __devexit annotation of
ag71xx_ar7240_cleanup.
SVN-Revision: 26855
2011-05-08 13:30:36 +00:00
ef53029870
ar71xx: ag71xx: fix build error if debugfs is enabled
...
SVN-Revision: 26854
2011-05-08 13:30:26 +00:00
ba1c1e9016
base-files: retrigger usb coldplug after module loading, solves usb_modeswitch on boot and possibly others ( #9352 )
...
SVN-Revision: 26848
2011-05-08 10:25:58 +00:00
732abc44cc
brcm47xx: update patches
...
SVN-Revision: 26846
2011-05-07 12:49:17 +00:00
8b67d748cb
ar71xx: ag71xx: add debugfs entry for [rt]x_ring
...
SVN-Revision: 26845
2011-05-07 12:40:34 +00:00
2166432ba0
ar71xx: ag71xx: add timestamps to ag71xx_buf
...
SVN-Revision: 26844
2011-05-07 12:40:28 +00:00
896e1d1ab4
ar71xx: ag71xx: use dynamically allocated buffer for napi_stats
...
SVN-Revision: 26843
2011-05-07 12:40:26 +00:00
a6708d20d1
ar71xx: ag71xx: use debugfs_remove_recursive
...
SVN-Revision: 26842
2011-05-07 12:40:25 +00:00
3b1b49a49b
base-files: fix a typo in etc/banner
...
SVN-Revision: 26841
2011-05-07 09:23:33 +00:00
c39e5b9360
ar71xx: override wmac device name for the AR934x SoCs
...
SVN-Revision: 26840
2011-05-07 09:23:32 +00:00
fbbe154a48
remove useless patches
...
SVN-Revision: 26837
2011-05-06 12:37:40 +00:00
de02a2795b
fill maintainer infos for a couple of targets
...
SVN-Revision: 26836
2011-05-06 12:37:36 +00:00
1adaa8790d
update to 2.6.38.2
...
SVN-Revision: 26833
2011-05-05 16:35:44 +00:00
fd33dffe60
add missing 2.6.38 symbols
...
SVN-Revision: 26832
2011-05-05 16:35:40 +00:00
fcb1557a3e
brcm47xx: when detecting a ssb pci device without an own sprom write the sprom data from the platform device to the correct pointer.
...
SVN-Revision: 26829
2011-05-05 14:05:21 +00:00
54fb8868fa
brcm47xx: fix typo in patch
...
SVN-Revision: 26828
2011-05-05 13:18:35 +00:00
7fb06ce6cd
linux/ar71xx: add some missing symbols for nand/yaffs targets
...
SVN-Revision: 26827
2011-05-05 07:19:46 +00:00
f3e4c15229
lua: remove posix from Lua core, almost nothing uses it - saves 9k compressed
...
SVN-Revision: 26822
2011-05-04 14:51:06 +00:00
dbea075cd4
ath9k: add noise floor calibration fix that should improve stability
...
SVN-Revision: 26819
2011-05-04 14:35:35 +00:00
c27ffb1912
linux/generic: port yaffs to 2.6.39
...
SVN-Revision: 26818
2011-05-04 09:35:06 +00:00
67339c1329
linux/rb532: use kernel and initramfs tags on image generation
...
SVN-Revision: 26817
2011-05-04 08:47:00 +00:00
9736cfef66
comgt: add tty hotplug remove handling, only iterate each tty once ( #9211 )
...
SVN-Revision: 26816
2011-05-04 08:19:07 +00:00
bba138c671
kernel: revert r26814
...
SVN-Revision: 26815
2011-05-03 21:25:36 +00:00
be2275b8e6
kernel: add kmod-crypto-ipsec kmod-crypto-ipsec bundles some otherwise unprovided kernel crypto modules that are useful for IPSEC. This is an alternative to breaking these modules out into kmod-crypto-wq (crypto_wq.ko), kmod-crypto-rng (rng.ko and krng.ko), and kmod-crypto-iv (eseqiv.ko and chainiv.ko).
...
Signed-off-by: Lars Hjersted <lars@hjersted.com>
SVN-Revision: 26814
2011-05-03 21:22:43 +00:00
3d0ac93274
kernel: add kmod-crypto-{wq,rng,iv} Add kmod-crypto-iv as a dependency for kmod-ipsec. Also remove the extraneous kmod-crypto-core dependency to eliminate recursion.
...
Signed-off-by: Lars Hjersted <lars@hjersted.com>
SVN-Revision: 26813
2011-05-03 21:21:05 +00:00
32f3c920a2
kernel: add kmod-crypto-{wq,rng,iv} This patch adds kmod-crypto-wq, kmod-crypto-rng, and kmod-crypto-iv packages. These packages provide some missing kernel crypto modules which are required for IPSEC. The strongswan4, ipsec-tools, and possibly other IPSEC packages do not work properly without these modules.
...
NOTE: The KCONFIG associated with each of these modules gets selected
whenever CRYPTO_MANAGER (kmod-crypto-manager) is selected so these
modules are already being built.
Signed-off-by: Lars Hjersted <lars@hjersted.com>
SVN-Revision: 26812
2011-05-03 21:19:56 +00:00
ae5435adc9
geos: remove unneeded modules The via-sata and gpio-nsc modules are both unneeded on the Geos platform.
...
SVN-Revision: 26811
2011-05-03 21:18:12 +00:00
29392373f3
comgt: move ifup invocation back into background subshell to prevent hotplug deadlocks
...
SVN-Revision: 26810
2011-05-03 19:45:55 +00:00
549067e2b4
comgt: move 3g hotplug handling to tty subsystem, fixes race on coldplug ( #9211 )
...
SVN-Revision: 26809
2011-05-03 19:39:13 +00:00
ff4203b9bd
base-files: cleanup permissions of device files in common hotplug rules ( #9211 )
...
SVN-Revision: 26808
2011-05-03 19:37:59 +00:00
d66dc5307d
hotplug2: introduce tty subsystem events ( #9211 )
...
SVN-Revision: 26807
2011-05-03 19:35:58 +00:00
2e9e4c435f
firewall: revert accidential committed changes from r26805
...
SVN-Revision: 26806
2011-05-02 12:55:36 +00:00
ad23dd94b6
firewall: provide examples of ssh port relocation on firewall and IPsec passthrough Two examples of potentially useful configurations (commented out, of course):
...
(a) map the ssh service running on the firewall to 22001 externally, without modifying the configuration of the daemon itself. this allows port 22 on the WAN side to then be port-forwarded to a
LAN-based machine if desired, or if not, simply obscures the port from external attack.
(b) allow IPsec/ESP and ISAKMP (UDP-based key exchange) to happen by default. useful for most modern VPN clients you might have on your WAN.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
SVN-Revision: 26805
2011-05-02 12:54:31 +00:00
8324bf036c
quilt: fix building with dash `test x == x` gives a syntax error with dash (standard in Debian). The modified patch reflects the current upstream: http://git.savannah.gnu.org/cgit/quilt.git/commit/?id=38df0b210c3df67f3e784af92232ae1946b98ecd
...
SVN-Revision: 26804
2011-05-02 12:53:32 +00:00
a18ec3c37e
update to 2.6.38
...
SVN-Revision: 26803
2011-05-02 07:57:25 +00:00
af53fa1d91
cns3xxx: remove one of the dma cache patches, it causes a regression in the ethernet driver
...
SVN-Revision: 26802
2011-05-02 00:28:30 +00:00
3dbb8c5088
brcm47xx: add fallback sprom for pci devices without an own sprom.
...
If there is no sprom on an ssb based pci device on the brcm47xx
architecture ssb now asks the architecture code to look into the nvram
to get some sprom data for this device. Now we are able to read out
pci/1/1/ foo or pci/1/3/ foo config options.
This will fix some problems where the wireless devices does not got an
mac address and the following message was show:
ssb: WARNING: Invalid SPROM CRC (corrupt SPROM)
SVN-Revision: 26801
2011-05-01 20:28:35 +00:00
Florian Fainelli
John Crispin
Gabor Juhos
Travis Kemen
Jo-Philipp Wich
Hauke Mehrtens
Alexandros C. Couloumbis
Felix Fietkau