openwrt-owl/target/linux/ar71xx/image/generic.mk

837 lines
26 KiB
Makefile
Raw Normal View History

define Device/ap531b0
DEVICE_TITLE := Rockeetech AP531B0
DEVICE_PACKAGES := kmod-usb-core kmod-usb2
BOARDNAME = AP531B0
IMAGE_SIZE := 16000k
MTDPARTS := spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,16000k(firmware),64k(art)ro
endef
TARGET_DEVICES += ap531b0
define Device/ap90q
DEVICE_TITLE := YunCore AP90Q
BOARDNAME = AP90Q
IMAGE_SIZE = 16000k
MTDPARTS = spi0.0:256k(u-boot)ro,64k(u-boot-env),16000k(firmware),64k(art)ro
endef
TARGET_DEVICES += ap90q
define Device/bsb
DEVICE_TITLE := Smart Electronics Black Swift board
DEVICE_PACKAGES := kmod-usb-core kmod-usb2
BOARDNAME = BSB
IMAGE_SIZE = 16000k
CONSOLE = ttyATH0,115200
MTDPARTS = spi0.0:128k(u-boot)ro,64k(u-boot-env)ro,16128k(firmware),64k(art)ro
endef
TARGET_DEVICES += bsb
define Device/carambola2
DEVICE_TITLE := Carambola2 board from 8Devices
DEVICE_PACKAGES := kmod-usb-core kmod-usb2
BOARDNAME = CARAMBOLA2
IMAGE_SIZE = 16000k
CONSOLE = ttyATH0,115200
MTDPARTS = spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,16000k(firmware),64k(art)ro
endef
TARGET_DEVICES += carambola2
define Device/cf-e316n-v2
DEVICE_TITLE := COMFAST CF-E316N v2
BOARDNAME = CF-E316N-V2
IMAGE_SIZE = 16192k
MTDPARTS = spi0.0:64k(u-boot)ro,64k(art)ro,16192k(firmware),64k(art-backup)ro
endef
TARGET_DEVICES += cf-e316n-v2
define Device/cf-e320n-v2
$(Device/cf-e316n-v2)
DEVICE_TITLE := COMFAST CF-E320N v2
DEVICE_PACKAGES := kmod-usb-core kmod-usb2
BOARDNAME = CF-E320N-V2
endef
TARGET_DEVICES += cf-e320n-v2
define Device/cf-e380ac-v1
DEVICE_TITLE := COMFAST CF-E380AC v1
DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-ath10k ath10k-firmware-qca988x
BOARDNAME = CF-E380AC-V1
IMAGE_SIZE = 16128k
MTDPARTS = spi0.0:128k(u-boot)ro,64k(art)ro,16128k(firmware),64k(art-backup)ro
endef
TARGET_DEVICES += cf-e380ac-v1
define Device/cf-e380ac-v2
$(Device/cf-e380ac-v1)
DEVICE_TITLE := COMFAST CF-E380AC v2
BOARDNAME = CF-E380AC-V2
IMAGE_SIZE = 16000k
MTDPARTS = spi0.0:256k(u-boot)ro,64k(art)ro,16000k(firmware),64k(art-backup)ro
endef
TARGET_DEVICES += cf-e380ac-v2
define Device/cf-e520n
DEVICE_TITLE := COMFAST CF-E520N
DEVICE_PACKAGES := kmod-usb-core kmod-usb2
BOARDNAME = CF-E520N
IMAGE_SIZE = 8000k
MTDPARTS = spi0.0:64k(u-boot)ro,64k(art)ro,8000k(firmware),64k(art-backup)ro
endef
TARGET_DEVICES += cf-e520n
define Device/cf-e530n
$(Device/cf-e520n)
DEVICE_TITLE := COMFAST CF-E530N
BOARDNAME = CF-E530N
endef
TARGET_DEVICES += cf-e530n
ar71xx: add support for P&W R602N and CPE505N P&W (full name: Shenzhen Progress&Win Technologies) R602N (could be also labeled as R602F, R602, etc.) is a simple N300 router with 5-port 10/100 Mbps switch, non-detachable antennas and USB. CPE505 is an outdoor CPE with PoE support and detachable antennas. Both devices are based on Qualcomm/Atheros QCA9531 v2. Common specification: - 650/597/216 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 16 MB of FLASH - UART (J2) header on PCB R602N specification: - 5x 10/100 Mbps Ethernet - 1x USB 2.0 - 2T2R 2.4 GHz with external LNA and PA (SE2576L), up to 28 dBm - 2x external, non-detachable antennas - 7x LED, 1x button CPE505N specification: - 2x 10/100 Mbps Ethernet (both ports support passive PoE 12-24 V) - 2T2R 2.4 GHz with external LNA and PA (SKY65174-21), up to 30 dBm - 2x external, detachable antennas (RP-SMA connectors) - 1x RGB LED, 2x LEDs (in RJ45 sockets), 1x button Flash instructions: It seems that there are many different versions of the firmware which these devices are shipped with. The generic/standard one is based on some modified OpenWrt and LEDE firmware can be flashed directly from vendor's webgui or with sysupgrade (root password is "admin123"). Before flashing, make sure (use "fw_printenv") that the kernel load address in your device is set to "0x9f050000" (bootcmd variable is "bootm 0x9f050000"). If your device uses different load address, you should first change it, under vendor's firmware, with command: fw_setenv bootcmd "bootm 0x9f050000 || bootm OLD_ADDRESS" Where OLD_ADDRESS is previous kernel load address (in CPE505 version I got access to, it was "0x9fe80000"). This will allow you to use both the vendor's and LEDE firmware. If version of your device contains empty U-Boot environment (you will get information about this after issuing "fw_printenv"), you should use U-Boot, serial line access and TFTP to perform firmware upgrade: 1. tftp 0x80060000 lede-ar71xx-generic-...-squashfs-sysupgrade.bin 2. erase 0x9f050000 +$filesize 3. cp.b $fileaddr 0x9f050000 $filesize 4. setenv bootcmd "bootm 0x9f050000 || bootm OLD_ADDRESS" 5. saveenv && reset These devices contain also web recovery mode inside U-Boot. It can be started with pressing the reset button for around 3 seconds just after the device powerup. Web recovery panel is available on "192.168.10.9" and to be able to use it, IP on your PC must be set to "192.168.10.10". Make sure to change kernel load address before using recovery mode or the U-Boot will not be able to load LEDE firmware. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-03-15 23:54:08 +00:00
define Device/cpe505n
DEVICE_TITLE := P&W CPE505N
BOARDNAME = CPE505N
IMAGE_SIZE = 16000k
MTDPARTS = spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,16000k(firmware),64k(art)ro
endef
TARGET_DEVICES += cpe505n
define Device/cpe830
$(Device/ap90q)
DEVICE_TITLE := YunCore CPE830
DEVICE_PACKAGES := rssileds
BOARDNAME = CPE830
endef
TARGET_DEVICES += cpe830
define Device/cpe870
DEVICE_TITLE := YunCore CPE870
DEVICE_PACKAGES := rssileds
BOARDNAME = CPE870
IMAGE_SIZE = 7936k
MTDPARTS = spi0.0:64k(u-boot)ro,64k(u-boot-env),7936k(firmware),64k(config)ro,64k(art)ro
endef
TARGET_DEVICES += cpe870
define Device/dragino2
BOARDNAME := DRAGINO2
CONSOLE := ttyATH0,115200
DEVICE_PACKAGES := kmod-usb-core kmod-usb-ohci kmod-usb2 kmod-usb-ledtrig-usbport
DEVICE_TITLE := Dragino 2 (MS14)
IMAGE_SIZE := 16000k
MTDPARTS := spi0.0:256k(u-boot)ro,16000k(firmware),64k(config)ro,64k(art)ro
endef
TARGET_DEVICES += dragino2
define Device/weio
DEVICE_TITLE := WeIO
DEVICE_PACKAGES := kmod-usb-core kmod-usb2
BOARDNAME = WEIO
IMAGE_SIZE = 16000k
CONSOLE = ttyATH0,115200
MTDPARTS = spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,16000k(firmware),64k(art)ro
endef
TARGET_DEVICES += weio
define Device/gl-ar150
DEVICE_TITLE := GL AR150
DEVICE_PACKAGES := kmod-usb-core kmod-usb2
BOARDNAME = GL-AR150
IMAGE_SIZE = 16000k
CONSOLE = ttyATH0,115200
MTDPARTS = spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,16000k(firmware),64k(art)ro
endef
TARGET_DEVICES += gl-ar150
define Device/gl-ar300
DEVICE_TITLE := GL AR300
DEVICE_PACKAGES := kmod-usb-core kmod-usb2
BOARDNAME = GL-AR300
IMAGE_SIZE = 16000k
MTDPARTS = spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,16000k(firmware),64k(art)ro
endef
TARGET_DEVICES += gl-ar300
define Device/gl-ar300m
DEVICE_TITLE := GL AR300M
DEVICE_PACKAGES := kmod-usb-core kmod-usb2 uboot-envtools
BOARDNAME = GL-AR300M
IMAGE_SIZE = 16000k
MTDPARTS = spi0.0:256k(u-boot)ro,64k(u-boot-env),16000k(firmware),64k(art)ro
endef
TARGET_DEVICES += gl-ar300m
define Device/gl-domino
DEVICE_TITLE := GL Domino Pi
DEVICE_PACKAGES := kmod-usb-core kmod-usb2
BOARDNAME = DOMINO
IMAGE_SIZE = 16000k
CONSOLE = ttyATH0,115200
MTDPARTS = spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,16000k(firmware),64k(art)ro
endef
TARGET_DEVICES += gl-domino
define Device/gl-mifi
DEVICE_TITLE := GL MIFI
DEVICE_PACKAGES := kmod-usb-core kmod-usb2
BOARDNAME = GL-MIFI
IMAGE_SIZE = 16000k
CONSOLE = ttyATH0,115200
MTDPARTS = spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,16000k(firmware),64k(art)ro
endef
TARGET_DEVICES += gl-mifi
define Device/lima
DEVICE_TITLE := Lima board from 8Devices
DEVICE_PACKAGES := kmod-usb-core kmod-usb2
BOARDNAME = LIMA
IMAGE_SIZE = 15616k
MTDPARTS = spi0.0:256k(u-boot)ro,256k(u-boot-env)ro,256k(art)ro,-(firmware)
endef
TARGET_DEVICES += lima
define Device/mr12
DEVICE_TITLE := Meraki MR12
DEVICE_PACKAGES := kmod-spi-gpio
BOARDNAME = MR12
IMAGE_SIZE = 15680k
MTDPARTS = spi0.0:256k(u-boot)ro,256k(u-boot-env)ro,13440k(rootfs),2240k(kernel),64k(mac),128k(art)ro,15680k@0x80000(firmware)
IMAGE/kernel.bin = append-kernel
IMAGE/rootfs.bin = append-rootfs | pad-rootfs
IMAGE/sysupgrade.bin = append-rootfs | pad-rootfs | pad-to 13440k | append-kernel | check-size $$$$(IMAGE_SIZE)
IMAGES := kernel.bin rootfs.bin sysupgrade.bin
endef
TARGET_DEVICES += mr12
define Device/mr16
DEVICE_TITLE := Meraki MR16
DEVICE_PACKAGES := kmod-spi-gpio
BOARDNAME = MR16
IMAGE_SIZE = 15680k
MTDPARTS = spi0.0:256k(u-boot)ro,256k(u-boot-env)ro,13440k(rootfs),2240k(kernel),64k(mac),128k(art)ro,15680k@0x80000(firmware)
IMAGE/kernel.bin = append-kernel
IMAGE/rootfs.bin = append-rootfs | pad-rootfs
IMAGE/sysupgrade.bin = append-rootfs | pad-rootfs | pad-to 13440k | append-kernel | check-size $$$$(IMAGE_SIZE)
IMAGES := kernel.bin rootfs.bin sysupgrade.bin
endef
TARGET_DEVICES += mr16
define Device/dr531
DEVICE_TITLE := Wallys DR531
DEVICE_PACKAGES := kmod-usb-core kmod-usb2
BOARDNAME = DR531
IMAGE_SIZE = 7808k
MTDPARTS = spi0.0:192k(u-boot)ro,64k(u-boot-env),64k(partition-table)ro,7808k(firmware),64k(art)ro
endef
TARGET_DEVICES += dr531
define Device/wndr3700
DEVICE_TITLE := NETGEAR WNDR3700
DEVICE_PACKAGES := kmod-usb-core kmod-usb-ohci kmod-usb2 kmod-usb-ledtrig-usbport kmod-leds-wndr3700-usb
BOARDNAME = WNDR3700
NETGEAR_KERNEL_MAGIC = 0x33373030
NETGEAR_BOARD_ID = WNDR3700
IMAGE_SIZE = 7680k
MTDPARTS = spi0.0:320k(u-boot)ro,128k(u-boot-env)ro,7680k(firmware),64k(art)ro
IMAGES := sysupgrade.bin factory.img factory-NA.img
KERNEL := kernel-bin | patch-cmdline | lzma -d20 | netgear-uImage lzma
IMAGE/default = append-kernel | pad-to $$$$(BLOCKSIZE) | netgear-squashfs | append-rootfs | pad-rootfs
IMAGE/sysupgrade.bin = $$(IMAGE/default) | check-size $$$$(IMAGE_SIZE)
IMAGE/factory.img = $$(IMAGE/default) | netgear-dni | check-size $$$$(IMAGE_SIZE)
IMAGE/factory-NA.img = $$(IMAGE/default) | netgear-dni NA | check-size $$$$(IMAGE_SIZE)
endef
define Device/wndr3700v2
$(Device/wndr3700)
DEVICE_TITLE := NETGEAR WNDR3700 v2
NETGEAR_BOARD_ID = WNDR3700v2
NETGEAR_KERNEL_MAGIC = 0x33373031
NETGEAR_HW_ID = 29763654+16+64
IMAGE_SIZE = 15872k
MTDPARTS = spi0.0:320k(u-boot)ro,128k(u-boot-env)ro,15872k(firmware),64k(art)ro
IMAGES := sysupgrade.bin factory.img
endef
define Device/wndr3800
$(Device/wndr3700v2)
DEVICE_TITLE := NETGEAR WNDR3800
NETGEAR_BOARD_ID = WNDR3800
NETGEAR_HW_ID = 29763654+16+128
endef
define Device/wndr3800ch
$(Device/wndr3800)
DEVICE_TITLE := NETGEAR WNDR3800 (Ch)
NETGEAR_BOARD_ID = WNDR3800CH
endef
define Device/wndrmac
$(Device/wndr3700v2)
DEVICE_TITLE := NETGEAR WNDRMAC
NETGEAR_BOARD_ID = WNDRMAC
endef
define Device/wndrmacv2
$(Device/wndr3800)
DEVICE_TITLE := NETGEAR WNDRMAC v2
NETGEAR_BOARD_ID = WNDRMACv2
endef
TARGET_DEVICES += wndr3700 wndr3700v2 wndr3800 wndr3800ch wndrmac wndrmacv2
define Device/cap324
DEVICE_TITLE := PowerCloud CAP324 Cloud AP
DEVICE_PACKAGES := uboot-envtools
BOARDNAME := CAP324
DEVICE_PROFILE := CAP324
IMAGE_SIZE = 15296k
MTDPARTS = spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,15296k(firmware),640k(certs),64k(nvram),64k(art)ro
endef
TARGET_DEVICES += cap324
define Device/cap324-nocloud
DEVICE_TITLE := PowerCloud CAP324 Cloud AP (No-Cloud)
DEVICE_PACKAGES := uboot-envtools
BOARDNAME := CAP324
DEVICE_PROFILE := CAP324
IMAGE_SIZE = 16000k
MTDPARTS = spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,16000k(firmware),64k(art)ro
endef
TARGET_DEVICES += cap324-nocloud
define Device/cr3000
DEVICE_TITLE := PowerCloud CR3000 Cloud Router
DEVICE_PACKAGES := uboot-envtools
BOARDNAME := CR3000
DEVICE_PROFILE := CR3000
IMAGE_SIZE = 7104k
MTDPARTS = spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,7104k(firmware),640k(certs),64k(nvram),64k(art)ro
endef
TARGET_DEVICES += cr3000
define Device/cr3000-nocloud
DEVICE_TITLE := PowerCloud CR3000 (No-Cloud)
DEVICE_PACKAGES := uboot-envtools
BOARDNAME := CR3000
DEVICE_PROFILE := CR3000
IMAGE_SIZE = 7808k
MTDPARTS = spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,7808k(firmware),64k(art)ro
endef
TARGET_DEVICES += cr3000-nocloud
define Device/cr5000
DEVICE_TITLE := PowerCloud CR5000 Cloud Router
DEVICE_PACKAGES := uboot-envtools kmod-usb2 kmod-usb-ohci kmod-usb-ledtrig-usbport kmod-usb-core
BOARDNAME := CR5000
DEVICE_PROFILE := CR5000
IMAGE_SIZE = 7104k
MTDPARTS = spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,7104k(firmware),640k(certs),64k(nvram),64k(art)ro
endef
TARGET_DEVICES += cr5000
define Device/cr5000-nocloud
DEVICE_TITLE := PowerCloud CR5000 (No-Cloud)
DEVICE_PACKAGES := uboot-envtools kmod-usb2 kmod-usb-ohci kmod-usb-ledtrig-usbport kmod-usb-core
BOARDNAME := CR5000
DEVICE_PROFILE := CR5000
IMAGE_SIZE = 7808k
MTDPARTS = spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,7808k(firmware),64k(art)ro
endef
TARGET_DEVICES += cr5000-nocloud
define Device/pqi-air-pen
DEVICE_TITLE := PQI Air Pen
DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-usb-storage
BOARDNAME = PQI-AIR-PEN
IMAGE_SIZE = 7744k
CONSOLE = ttyATH0,115200
MTDPARTS = spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,64k(art)ro,64k(NVRAM)ro,7680k(firmware),64k(CONF)
endef
TARGET_DEVICES += pqi-air-pen
define Device/antminer-s1
$(Device/tplink-8mlzma)
DEVICE_TITLE := Antminer-S1
DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-crypto-manager kmod-i2c-gpio-custom kmod-usb-hid
BOARDNAME := ANTMINER-S1
DEVICE_PROFILE := ANTMINERS1
TPLINK_HWID := 0x04440101
CONSOLE := ttyATH0,115200
endef
define Device/antminer-s3
$(Device/tplink-8mlzma)
DEVICE_TITLE := Antminer-S3
DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-crypto-manager kmod-i2c-gpio-custom kmod-usb-hid
BOARDNAME := ANTMINER-S3
DEVICE_PROFILE := ANTMINERS3
TPLINK_HWID := 0x04440301
CONSOLE := ttyATH0,115200
endef
define Device/antrouter-r1
$(Device/tplink-8mlzma)
DEVICE_TITLE := Antrouter-R1
DEVICE_PACKAGES := kmod-usb-core kmod-usb2
BOARDNAME := ANTROUTER-R1
DEVICE_PROFILE := ANTROUTERR1
TPLINK_HWID := 0x44440101
CONSOLE := ttyATH0,115200
endef
define Device/el-m150
$(Device/tplink-8mlzma)
DEVICE_TITLE := EasyLink EL-M150
DEVICE_PACKAGES := kmod-usb-core kmod-usb2
BOARDNAME := EL-M150
DEVICE_PROFILE := ELM150
TPLINK_HWID := 0x01500101
CONSOLE := ttyATH0,115200
endef
define Device/el-mini
$(Device/tplink-8mlzma)
DEVICE_TITLE := EasyLink EL-MINI
DEVICE_PACKAGES := kmod-usb-core kmod-usb2
BOARDNAME := EL-MINI
DEVICE_PROFILE := ELMINI
TPLINK_HWID := 0x01530001
CONSOLE := ttyATH0,115200
endef
TARGET_DEVICES += antminer-s1 antminer-s3 antrouter-r1 el-m150 el-mini
define Device/gl-inet-6408A-v1
$(Device/tplink-8mlzma)
DEVICE_TITLE := GL.iNet 6408
DEVICE_PACKAGES := kmod-usb-core kmod-usb2
BOARDNAME := GL-INET
DEVICE_PROFILE := GLINET
TPLINK_HWID := 0x08000001
CONSOLE := ttyATH0,115200
endef
define Device/gl-inet-6416A-v1
$(Device/tplink-16mlzma)
DEVICE_TITLE := GL.iNet 6416
DEVICE_PACKAGES := kmod-usb-core kmod-usb2
BOARDNAME := GL-INET
DEVICE_PROFILE := GLINET
TPLINK_HWID := 0x08000001
CONSOLE := ttyATH0,115200
endef
TARGET_DEVICES += gl-inet-6408A-v1 gl-inet-6416A-v1
define Device/jwap230
DEVICE_TITLE := jjPlus JWAP230
DEVICE_PACKAGES := kmod-usb-core kmod-usb2
BOARDNAME = JWAP230
IMAGE_SIZE = 16000k
MTDPARTS = spi0.0:256k(u-boot)ro,64k(u-boot-env),16000k(firmware),64k(art)ro
endef
TARGET_DEVICES += jwap230
ar71xx: add support for P&W R602N and CPE505N P&W (full name: Shenzhen Progress&Win Technologies) R602N (could be also labeled as R602F, R602, etc.) is a simple N300 router with 5-port 10/100 Mbps switch, non-detachable antennas and USB. CPE505 is an outdoor CPE with PoE support and detachable antennas. Both devices are based on Qualcomm/Atheros QCA9531 v2. Common specification: - 650/597/216 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 16 MB of FLASH - UART (J2) header on PCB R602N specification: - 5x 10/100 Mbps Ethernet - 1x USB 2.0 - 2T2R 2.4 GHz with external LNA and PA (SE2576L), up to 28 dBm - 2x external, non-detachable antennas - 7x LED, 1x button CPE505N specification: - 2x 10/100 Mbps Ethernet (both ports support passive PoE 12-24 V) - 2T2R 2.4 GHz with external LNA and PA (SKY65174-21), up to 30 dBm - 2x external, detachable antennas (RP-SMA connectors) - 1x RGB LED, 2x LEDs (in RJ45 sockets), 1x button Flash instructions: It seems that there are many different versions of the firmware which these devices are shipped with. The generic/standard one is based on some modified OpenWrt and LEDE firmware can be flashed directly from vendor's webgui or with sysupgrade (root password is "admin123"). Before flashing, make sure (use "fw_printenv") that the kernel load address in your device is set to "0x9f050000" (bootcmd variable is "bootm 0x9f050000"). If your device uses different load address, you should first change it, under vendor's firmware, with command: fw_setenv bootcmd "bootm 0x9f050000 || bootm OLD_ADDRESS" Where OLD_ADDRESS is previous kernel load address (in CPE505 version I got access to, it was "0x9fe80000"). This will allow you to use both the vendor's and LEDE firmware. If version of your device contains empty U-Boot environment (you will get information about this after issuing "fw_printenv"), you should use U-Boot, serial line access and TFTP to perform firmware upgrade: 1. tftp 0x80060000 lede-ar71xx-generic-...-squashfs-sysupgrade.bin 2. erase 0x9f050000 +$filesize 3. cp.b $fileaddr 0x9f050000 $filesize 4. setenv bootcmd "bootm 0x9f050000 || bootm OLD_ADDRESS" 5. saveenv && reset These devices contain also web recovery mode inside U-Boot. It can be started with pressing the reset button for around 3 seconds just after the device powerup. Web recovery panel is available on "192.168.10.9" and to be able to use it, IP on your PC must be set to "192.168.10.10". Make sure to change kernel load address before using recovery mode or the U-Boot will not be able to load LEDE firmware. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2017-03-15 23:54:08 +00:00
define Device/r602n
DEVICE_TITLE := P&W R602N
DEVICE_PACKAGES := kmod-usb-core kmod-usb2
BOARDNAME = R602N
IMAGE_SIZE = 16000k
MTDPARTS = spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,16000k(firmware),64k(art)ro
endef
TARGET_DEVICES += r602n
define Device/rnx-n360rt
$(Device/tplink-4m)
DEVICE_TITLE := Rosewill RNX-N360RT
BOARDNAME := TL-WR941ND
DEVICE_PROFILE := RNXN360RT
TPLINK_HWID := 0x09410002
TPLINK_HWREV := 0x00420001
endef
TARGET_DEVICES += rnx-n360rt
define Device/mc-mac1200r
$(Device/tplink-8mlzma)
DEVICE_TITLE := Mercury MAC1200R
DEVICE_PACKAGES := kmod-ath10k ath10k-firmware-qca988x
BOARDNAME := MC-MAC1200R
DEVICE_PROFILE := MAC1200R
TPLINK_HWID := 0x12000001
endef
TARGET_DEVICES += mc-mac1200r
define Device/minibox-v1
$(Device/tplink-16mlzma)
DEVICE_TITLE := Gainstrong MiniBox V1.0
DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-usb-ledtrig-usbport
BOARDNAME := MINIBOX-V1
DEVICE_PROFILE := MINIBOXV1
TPLINK_HWID := 0x3C000201
CONSOLE := ttyATH0,115200
endef
TARGET_DEVICES += minibox-v1
define Device/omy-g1
$(Device/tplink-16mlzma)
DEVICE_TITLE := OMYlink OMY-G1
DEVICE_PACKAGES := kmod-usb-core kmod-usb2
BOARDNAME := OMY-G1
DEVICE_PROFILE := OMYG1
TPLINK_HWID := 0x06660101
endef
define Device/omy-x1
$(Device/tplink-8mlzma)
DEVICE_TITLE := OMYlink OMY-X1
BOARDNAME := OMY-X1
DEVICE_PROFILE := OMYX1
TPLINK_HWID := 0x06660201
endef
TARGET_DEVICES += omy-g1 omy-x1
define Device/onion-omega
$(Device/tplink-16mlzma)
DEVICE_TITLE := Onion Omega
DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-usb-storage kmod-i2c-core kmod-i2c-gpio-custom kmod-spi-bitbang kmod-spi-dev kmod-spi-gpio kmod-spi-gpio-custom kmod-usb-serial
BOARDNAME := ONION-OMEGA
DEVICE_PROFILE := OMEGA
TPLINK_HWID := 0x04700001
CONSOLE := ttyATH0,115200
endef
TARGET_DEVICES += onion-omega
define Device/sc1750
DEVICE_TITLE := Abicom SC1750
DEVICE_PACKAGES := kmod-usb-core kmod-usb-ohci kmod-usb2 kmod-usb-ledtrig-usbport
BOARDNAME = SC1750
IMAGE_SIZE = 15744k
MTDPARTS = spi0.0:256k(u-boot)ro,64k(u-boot-env),15744k(firmware),128k(APConfig),128k(kplog),64k(ART)
endef
TARGET_DEVICES += sc1750
define Device/sc300m
DEVICE_TITLE := Abicom SC300M
DEVICE_PACKAGES := kmod-usb-core kmod-usb-ohci kmod-usb2 kmod-usb-ledtrig-usbport
BOARDNAME = SC300M
IMAGE_SIZE = 15744k
MTDPARTS = spi0.0:256k(u-boot)ro,64k(u-boot-env),15744k(firmware),128k(APConfig),128k(kplog),64k(ART)
endef
TARGET_DEVICES += sc300m
define Device/sc450
DEVICE_TITLE := Abicom SC450
DEVICE_PACKAGES := kmod-usb-core kmod-usb-ohci kmod-usb2 kmod-usb-ledtrig-usbport
BOARDNAME = SC450
IMAGE_SIZE = 15744k
MTDPARTS = spi0.0:256k(u-boot)ro,64k(u-boot-env),15744k(firmware),128k(APConfig),128k(kplog),64k(ART)
endef
TARGET_DEVICES += sc450
define Device/smart-300
$(Device/tplink-8mlzma)
DEVICE_TITLE := NC-LINK SMART-300
BOARDNAME := SMART-300
DEVICE_PROFILE := SMART-300
TPLINK_HWID := 0x93410001
endef
TARGET_DEVICES += smart-300
define Device/som9331
$(Device/tplink-8mlzma)
DEVICE_TITLE := OpenEmbed SOM9331
DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-usb-storage kmod-i2c-core kmod-i2c-gpio-custom kmod-spi-bitbang kmod-spi-dev kmod-spi-gpio kmod-spi-gpio-custom kmod-usb-serial
BOARDNAME := SOM9331
DEVICE_PROFILE := SOM9331
TPLINK_HWID := 0x04800054
CONSOLE := ttyATH0,115200
endef
TARGET_DEVICES += som9331
ar71xx: add support for YunCore SR3200 and XD3200 YunCore SR3200 is a dual-band AC1200 router, based on Qualcomm/Atheros QCA9563+QCA9882+QCA8337N. YunCore XD3200 (FCC ID: 2ADUG-XD3200) is a dual-band AC1200 ceiling mount AP with PoE support, based on Qualcomm/Atheros QCA9563+QCA9882+QCA8334. Common specification: - 775/650/258 MHz (CPU/DDR/AHB) - 128 MB or RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 2T2R 2.4 GHz, with ext. PA (SKY65174-21), up to 30 dBm - 2T2R 5 GHz, with ext. PA (SKY85405-11) and LNA (SKY85601-11), up to 30 dBm SR3200 specification: - 5x 10/100/1000 Mbps Ethernet - 6x ext. RP-SMA antennas (actually, only 4 are connected with radio chips) - 3x LED (+ 5x LED in RJ45 sockets), 1x button - UART header on PCB XD3200 specification: - 2x 10/100/1000 Mbps Ethernet, with 802.3at PoE support (WAN port) - 4x internal antennas - 3 sets of LEDs on external PCB (+ 2x LED near RJ45 sockets), 1x button - UART and JTAG (custom 6-pin, 2 mm pitch) headers on PCB LED for 5 GHz WLAN is currently not supported on both devices as it is connected directly to the QCA9882 radio chip. Flash instruction under vendor firmware, using telnet/SSH: 1. If your firmware does not have root password, go to point 5 2. Connect PC with 192.168.1.x address to LAN or WAN port 3. Power up device, enter failsafe mode with button (no LED indicator!) 4. Change root password and reboot (mount_root, passwd ..., reboot -f) 5. Upload lede-ar71xx-...-sysupgrade.bin to /tmp using SCP 6. Connect PC with 192.168.188.x address to LAN port, SSH to 192.168.188.253 7. Invoke: - cd /tmp - fw_setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000" - mtd -e firmware -r write lede-ar71xx-...-sysupgrade.bin firmware Flash instruction under U-Boot, using UART: 1. tftp 0x80060000 lede-ar71xx-...-sysupgrade.bin 2. erase 0x9f050000 +$filesize 3. cp.b $fileaddr 0x9f050000 $filesize 4. setenv bootcmd "bootm 0x9fe80000 || bootm 0x9f050000" 5. saveenv && reset Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2016-12-02 21:42:41 +00:00
define Device/sr3200
DEVICE_TITLE := YunCore SR3200
DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-ath10k ath10k-firmware-qca988x
BOARDNAME = SR3200
IMAGE_SIZE = 16000k
MTDPARTS = spi0.0:256k(u-boot)ro,64k(u-boot-env),16000k(firmware),64k(art)ro
endef
TARGET_DEVICES += sr3200
define Device/xd3200
$(Device/sr3200)
DEVICE_TITLE := YunCore XD3200
DEVICE_PACKAGES := kmod-ath10k ath10k-firmware-qca988x
BOARDNAME = XD3200
endef
TARGET_DEVICES += xd3200
define Device/tellstick-znet-lite
$(Device/tplink-16mlzma)
DEVICE_TITLE := TellStick ZNet Lite
DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-usb-acm kmod-usb-serial kmod-usb-serial-pl2303
BOARDNAME := TELLSTICK-ZNET-LITE
DEVICE_PROFILE := TELLSTICKZNETLITE
TPLINK_HWID := 0x00726001
CONSOLE := ttyATH0,115200
endef
TARGET_DEVICES += tellstick-znet-lite
define Device/oolite
$(Device/tplink-16mlzma)
DEVICE_TITLE := Gainstrong OOLITE
DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-usb-ledtrig-usbport
BOARDNAME := GS-OOLITE
DEVICE_PROFILE := OOLITE
TPLINK_HWID := 0x3C000101
CONSOLE := ttyATH0,115200
endef
TARGET_DEVICES += oolite
define Device/NBG6616
DEVICE_TITLE := ZyXEL NBG6616
DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-usb-ledtrig-usbport kmod-usb-storage kmod-rtc-pcf8563 kmod-ath10k ath10k-firmware-qca988x
BOARDNAME = NBG6616
KERNEL_SIZE = 2048k
IMAGE_SIZE = 15323k
MTDPARTS = spi0.0:192k(u-boot)ro,64k(env)ro,64k(RFdata)ro,384k(zyxel_rfsd),384k(romd),64k(header),2048k(kernel),13184k(rootfs),15232k@0x120000(firmware)
CMDLINE += mem=128M
IMAGES := sysupgrade.bin
KERNEL := kernel-bin | patch-cmdline | lzma | uImage lzma | jffs2 boot/vmlinux.lzma.uImage
IMAGE/sysupgrade.bin = append-kernel | pad-to $$$$(KERNEL_SIZE) | append-rootfs | pad-rootfs | check-size $$$$(IMAGE_SIZE)
# We cannot currently build a factory image. It is the sysupgrade image
# prefixed with a header (which is actually written into the MTD device).
# The header is 2kiB and is filled with 0xff. The format seems to be:
# 2 bytes: 0x0000
# 2 bytes: checksum of the data partition (big endian)
# 4 bytes: length of the contained image file (big endian)
# 32 bytes: Firmware Version string (NUL terminated, 0xff padded)
# 2 bytes: 0x0000
# 2 bytes: checksum over the header partition (big endian)
# 32 bytes: Model (e.g. "NBG6616", NUL termiated, 0xff padded)
# rest: 0xff padding
#
# The checksums are calculated by adding up all bytes and if a 16bit
# overflow occurs, one is added and the sum is masked to 16 bit:
# csum = csum + databyte; if (csum > 0xffff) { csum += 1; csum &= 0xffff };
# Should the file have an odd number of bytes then the byte len-0x800 is
# used additionally.
# The checksum for the header is calcualted over the first 2048 bytes with
# the firmware checksum as the placeholder during calculation.
#
# The header is padded with 0xff to the erase block size of the device.
endef
TARGET_DEVICES += NBG6616
define Device/c-55
DEVICE_TITLE := AirTight Networks C-55
DEVICE_PACKAGES := kmod-ath9k
BOARDNAME = C-55
KERNEL_SIZE = 2048k
IMAGE_SIZE = 15872k
MTDPARTS = spi0.0:256k(u-boot)ro,128k(u-boot-env)ro,2048k(kernel),13824k(rootfs),13824k(opt)ro,2624k(failsafe)ro,64k(art)ro,15872k@0x60000(firmware)
IMAGE/sysupgrade.bin = append-kernel | pad-to $$$$(KERNEL_SIZE) | append-rootfs | pad-rootfs | check-size $$$$(IMAGE_SIZE)
endef
TARGET_DEVICES += c-55
define Build/uImageHiWiFi
# Field ih_name needs to start with "tw150v1"
mkimage -A $(LINUX_KARCH) \
-O linux -T kernel \
-C $(1) -a $(KERNEL_LOADADDR) -e $(if $(KERNEL_ENTRY),$(KERNEL_ENTRY),$(KERNEL_LOADADDR)) \
-n 'tw150v1 $(call toupper,$(LINUX_KARCH)) LEDE Linux-$(LINUX_VERSION)' -d $@ $@.new
@mv $@.new $@
endef
define Device/hiwifi-hc6361
DEVICE_TITLE := HiWiFi HC6361
DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-usb-storage \
kmod-fs-ext4 kmod-nls-iso8859-1 e2fsprogs
BOARDNAME := HiWiFi-HC6361
DEVICE_PROFILE := HIWIFI_HC6361
IMAGE_SIZE := 16128k
KERNEL := kernel-bin | patch-cmdline | lzma | uImageHiWiFi lzma
CONSOLE := ttyATH0,115200
MTDPARTS := spi0.0:64k(u-boot)ro,64k(bdinfo)ro,16128k(firmware),64k(backup)ro,64k(art)ro
endef
TARGET_DEVICES += hiwifi-hc6361
define Build/seama
$(STAGING_DIR_HOST)/bin/seama -i $@ $(if $(1),$(1),-m "dev=/dev/mtdblock/1" -m "type=firmware")
mv $@.seama $@
endef
define Build/seama-seal
$(call Build/seama,-s $@.seama $(1))
endef
define Device/seama
LOADER_TYPE := bin
BLOCKSIZE := 64k
KERNEL := kernel-bin | patch-cmdline | relocate-kernel | lzma
KERNEL_INITRAMFS := kernel-bin | patch-cmdline | lzma | seama
KERNEL_INITRAMFS_SUFFIX = $$(KERNEL_SUFFIX).seama
IMAGES := sysupgrade.bin factory.bin
# 64 bytes offset:
# - 28 bytes seama_header
# - 36 bytes of META data (4-bytes aligned)
IMAGE/default := append-kernel | pad-offset $$$$(BLOCKSIZE) 64 | append-rootfs
IMAGE/sysupgrade.bin := \
$$(IMAGE/default) | seama | pad-rootfs | \
check-size $$$$(IMAGE_SIZE)
IMAGE/factory.bin := \
$$(IMAGE/default) | seama | pad-rootfs | \
seama-seal -m "signature=$$$$(SEAMA_SIGNATURE)" | \
check-size $$$$(IMAGE_SIZE)
SEAMA_SIGNATURE :=
DEVICE_VARS += SEAMA_SIGNATURE
endef
define Device/dir-869-a1
$(Device/seama)
DEVICE_TITLE := D-Link DIR-869 rev. A1
DEVICE_PACKAGES := kmod-ath10k ath10k-firmware-qca988x
BOARDNAME = DIR-869-A1
IMAGE_SIZE = 15872k
MTDPARTS = spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,64k(devdata)ro,64k(devconf)ro,15872k(firmware),64k(radiocfg)ro
SEAMA_SIGNATURE := wrgac54_dlink.2015_dir869
IMAGE/factory.bin := \
$$(IMAGE/default) | pad-rootfs -x 64 | \
seama | seama-seal -m "signature=$$$$(SEAMA_SIGNATURE)" | \
check-size $$$$(IMAGE_SIZE)
endef
define Device/mynet-n600
$(Device/seama)
DEVICE_TITLE := Western Digital My Net N600
DEVICE_PACKAGES := kmod-usb-core kmod-usb2
BOARDNAME = MYNET-N600
IMAGE_SIZE = 15808k
MTDPARTS = spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,64k(devdata)ro,64k(devconf)ro,15872k(firmware),64k(radiocfg)ro
SEAMA_SIGNATURE := wrgnd16_wd_db600
endef
define Device/mynet-n750
$(Device/seama)
DEVICE_TITLE := Western Digital My Net N750
DEVICE_PACKAGES := kmod-usb-core kmod-usb2
BOARDNAME = MYNET-N750
IMAGE_SIZE = 15808k
MTDPARTS = spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,64k(devdata)ro,64k(devconf)ro,15872k(firmware),64k(radiocfg)ro
SEAMA_SIGNATURE := wrgnd13_wd_av
endef
define Device/qihoo-c301
$(Device/seama)
DEVICE_TITLE := Qihoo C301
DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-usb-ledtrig-usbport kmod-ath10k ath10k-firmware-qca988x
BOARDNAME = QIHOO-C301
IMAGE_SIZE = 15744k
MTDPARTS = spi0.0:256k(u-boot)ro,64k(u-boot-env),64k(devdata),64k(devconf),15744k(firmware),64k(warm_start),64k(action_image_config),64k(radiocfg)ro;spi0.1:15360k(upgrade2),1024k(privatedata)
SEAMA_SIGNATURE := wrgac26_qihoo360_360rg
endef
TARGET_DEVICES += dir-869-a1 mynet-n600 mynet-n750 qihoo-c301
define Build/mkwrggimg
$(STAGING_DIR_HOST)/bin/mkwrggimg -b \
-i $@ -o $@.imghdr -d /dev/mtdblock/1 \
-m $(BOARDNAME) -s $(DAP_SIGNATURE) \
-v LEDE -B $(REVISION)
mv $@.imghdr $@
endef
define Build/wrgg-pad-rootfs
$(STAGING_DIR_HOST)/bin/padjffs2 $(IMAGE_ROOTFS) -c 64 >>$@
endef
define Device/dap-2695-a1
DEVICE_TITLE := D-Link DAP-2695 rev. A1
DEVICE_PACKAGES := ath10k-firmware-qca988x kmod-ath10k uboot-envtools
BOARDNAME = DAP-2695-A1
IMAGES := factory.img sysupgrade.bin
IMAGE_SIZE = 15360k
IMAGE/factory.img = append-kernel | pad-offset 65536 160 | append-rootfs | wrgg-pad-rootfs | mkwrggimg | check-size $$$$(IMAGE_SIZE)
IMAGE/sysupgrade.bin = append-kernel | pad-offset 65536 160 | mkwrggimg | append-rootfs | wrgg-pad-rootfs | check-size $$$$(IMAGE_SIZE)
KERNEL := kernel-bin | patch-cmdline | relocate-kernel | lzma
KERNEL_INITRAMFS := $$(KERNEL) | mkwrggimg
MTDPARTS = spi0.0:256k(bootloader)ro,64k(bdcfg)ro,64k(rgdb)ro,64k(langpack)ro,15360k(firmware),448k(captival)ro,64k(certificate)ro,64k(radiocfg)ro
DAP_SIGNATURE := wapac02_dkbs_dap2695
DEVICE_VARS += DAP_SIGNATURE
endef
TARGET_DEVICES += dap-2695-a1
define Build/mkbuffaloimg
$(STAGING_DIR_HOST)/bin/mkbuffaloimg -B $(BOARDNAME) \
-R $$(($(subst k, * 1024,$(ROOTFS_SIZE)))) \
-K $$(($(subst k, * 1024,$(KERNEL_SIZE)))) \
-i $@ -o $@.new
mv $@.new $@
endef
define Device/bhr-4grv2
DEVICE_TITLE := Buffalo BHR-4GRV2
BOARDNAME := BHR-4GRV2
ROOTFS_SIZE := 14528k
KERNEL_SIZE := 1472k
IMAGE_SIZE := 16000k
MTDPARTS := spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,14528k(rootfs),1472k(kernel),64k(art)ro,16000k@0x50000(firmware)
IMAGES := sysupgrade.bin factory.bin
IMAGE/sysupgrade.bin = append-rootfs | pad-rootfs | pad-to $$$$(ROOTFS_SIZE) | append-kernel | check-size $$$$(IMAGE_SIZE)
IMAGE/factory.bin = append-kernel | pad-to $$$$(KERNEL_SIZE) | append-rootfs | pad-rootfs | mkbuffaloimg
endef
TARGET_DEVICES += bhr-4grv2
define Device/wpj342
DEVICE_TITLE := Compex WPJ342 (16MB flash)
DEVICE_PACKAGES := kmod-usb-core kmod-usb-ohci kmod-usb2 kmod-usb-ledtrig-usbport
BOARDNAME := WPJ342
MTDPARTS := spi0.0:192k(u-boot)ro,16128k(firmware),64k(art)ro
IMAGE_SIZE := 16128k
endef
TARGET_DEVICES += wpj342
define Device/wpj344
DEVICE_TITLE := Compex WPJ344 (16MB flash)
DEVICE_PACKAGES := kmod-usb-core kmod-usb-ohci kmod-usb2 kmod-usb-ledtrig-usbport
BOARDNAME := WPJ344
MTDPARTS := spi0.0:192k(u-boot)ro,16128k(firmware),64k(art)ro
IMAGE_SIZE := 16128k
endef
TARGET_DEVICES += wpj344
define Device/wpj531
DEVICE_TITLE := Compex WPJ531 (16MB flash)
DEVICE_PACKAGES := kmod-usb-core kmod-usb-ohci kmod-usb2 kmod-usb-ledtrig-usbport
BOARDNAME := WPJ531
MTDPARTS := spi0.0:192k(u-boot)ro,16128k(firmware),64k(art)ro
IMAGE_SIZE := 16128k
endef
TARGET_DEVICES += wpj531
define Device/wpj558
DEVICE_TITLE := Compex WPJ558 (16MB flash)
DEVICE_PACKAGES := kmod-usb-core kmod-usb-ohci kmod-usb2 kmod-usb-ledtrig-usbport
BOARDNAME := WPJ558
MTDPARTS := spi0.0:192k(u-boot)ro,16128k(firmware),64k(art)ro
IMAGE_SIZE := 16128k
endef
TARGET_DEVICES += wpj558
define Device/wpj563
DEVICE_TITLE := Compex WPJ563 (16MB flash)
DEVICE_PACKAGES := kmod-usb-core kmod-usb-ohci kmod-usb2 kmod-usb-ledtrig-usbport
BOARDNAME := WPJ563
MTDPARTS := spi0.0:192k(u-boot)ro,16128k(firmware),64k(art)ro
IMAGE_SIZE := 16128k
endef
TARGET_DEVICES += wpj563