mirror of https://github.com/hak5/openwrt-owl.git
98 lines
3.0 KiB
Diff
98 lines
3.0 KiB
Diff
|
From 11aa9df4de06cc257327d783c5cb615989e87286 Mon Sep 17 00:00:00 2001
|
||
|
|
From: Maxime Ripard <maxime.ripard@free-electrons.com>
|
||
|
|
Date: Fri, 23 Jan 2015 15:18:27 +0100
|
||
|
|
Subject: [PATCH v2 1/2] mtd: nand: pxa3xx: Fix PIO FIFO draining
|
||
|
|
|
||
|
|
The NDDB register holds the data that are needed by the read and write
|
||
|
|
commands.
|
||
|
|
|
||
|
|
However, during a read PIO access, the datasheet specifies that after each 32
|
||
|
|
bits read in that register, when BCH is enabled, we have to make sure that the
|
||
|
|
RDDREQ bit is set in the NDSR register.
|
||
|
|
|
||
|
|
This fixes an issue that was seen on the Armada 385, and presumably other mvebu
|
||
|
|
SoCs, when a read on a newly erased page would end up in the driver reporting a
|
||
|
|
timeout from the NAND.
|
||
|
|
|
||
|
|
Cc: <stable@vger.kernel.org> # v3.14
|
||
|
|
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
||
|
|
---
|
||
|
|
drivers/mtd/nand/pxa3xx_nand.c | 45 ++++++++++++++++++++++++++++++++++++------
|
||
|
|
1 file changed, 39 insertions(+), 6 deletions(-)
|
||
|
|
|
||
|
|
diff --git a/drivers/mtd/nand/pxa3xx_nand.c b/drivers/mtd/nand/pxa3xx_nand.c
|
||
|
|
index 96b0b1d27df1..e6918befb951 100644
|
||
|
|
--- a/drivers/mtd/nand/pxa3xx_nand.c
|
||
|
|
+++ b/drivers/mtd/nand/pxa3xx_nand.c
|
||
|
|
@@ -23,6 +23,7 @@
|
||
|
|
#include <linux/mtd/partitions.h>
|
||
|
|
#include <linux/io.h>
|
||
|
|
#include <linux/irq.h>
|
||
|
|
+#include <linux/jiffies.h>
|
||
|
|
#include <linux/slab.h>
|
||
|
|
#include <linux/of.h>
|
||
|
|
#include <linux/of_device.h>
|
||
|
|
@@ -480,6 +481,38 @@ static void disable_int(struct pxa3xx_nand_info *info, uint32_t int_mask)
|
||
|
|
nand_writel(info, NDCR, ndcr | int_mask);
|
||
|
|
}
|
||
|
|
|
||
|
|
+static void drain_fifo(struct pxa3xx_nand_info *info, void *data, int len)
|
||
|
|
+{
|
||
|
|
+ u32 *dst = (u32 *)data;
|
||
|
|
+
|
||
|
|
+ if (info->ecc_bch) {
|
||
|
|
+ while (len--) {
|
||
|
|
+ u32 timeout;
|
||
|
|
+
|
||
|
|
+ *dst++ = nand_readl(info, NDDB);
|
||
|
|
+
|
||
|
|
+ /*
|
||
|
|
+ * According to the datasheet, when reading
|
||
|
|
+ * from NDDB with BCH enabled, after each 32
|
||
|
|
+ * bits reads, we have to make sure that the
|
||
|
|
+ * NDSR.RDDREQ bit is set
|
||
|
|
+ */
|
||
|
|
+ timeout = jiffies + msecs_to_jiffies(5);
|
||
|
|
+ while (!(nand_readl(info, NDSR) & NDSR_RDDREQ)) {
|
||
|
|
+ if (!time_before(jiffies, timeout)) {
|
||
|
|
+ dev_err(&info->pdev->dev,
|
||
|
|
+ "Timeout on RDDREQ while draining the FIFO\n");
|
||
|
|
+ return;
|
||
|
|
+ }
|
||
|
|
+
|
||
|
|
+ cpu_relax();
|
||
|
|
+ }
|
||
|
|
+ }
|
||
|
|
+ } else {
|
||
|
|
+ __raw_readsl(info->mmio_base + NDDB, data, len);
|
||
|
|
+ }
|
||
|
|
+}
|
||
|
|
+
|
||
|
|
static void handle_data_pio(struct pxa3xx_nand_info *info)
|
||
|
|
{
|
||
|
|
unsigned int do_bytes = min(info->data_size, info->chunk_size);
|
||
|
|
@@ -496,14 +529,14 @@ static void handle_data_pio(struct pxa3xx_nand_info *info)
|
||
|
|
DIV_ROUND_UP(info->oob_size, 4));
|
||
|
|
break;
|
||
|
|
case STATE_PIO_READING:
|
||
|
|
- __raw_readsl(info->mmio_base + NDDB,
|
||
|
|
- info->data_buff + info->data_buff_pos,
|
||
|
|
- DIV_ROUND_UP(do_bytes, 4));
|
||
|
|
+ drain_fifo(info,
|
||
|
|
+ info->data_buff + info->data_buff_pos,
|
||
|
|
+ DIV_ROUND_UP(do_bytes, 4));
|
||
|
|
|
||
|
|
if (info->oob_size > 0)
|
||
|
|
- __raw_readsl(info->mmio_base + NDDB,
|
||
|
|
- info->oob_buff + info->oob_buff_pos,
|
||
|
|
- DIV_ROUND_UP(info->oob_size, 4));
|
||
|
|
+ drain_fifo(info,
|
||
|
|
+ info->oob_buff + info->oob_buff_pos,
|
||
|
|
+ DIV_ROUND_UP(info->oob_size, 4));
|
||
|
|
break;
|
||
|
|
default:
|
||
|
|
dev_err(&info->pdev->dev, "%s: invalid state %d\n", __func__,
|
||
|
|
--
|
||
|
|
2.2.2
|
||
|
|
|