774 lines
33 KiB
JavaScript
774 lines
33 KiB
JavaScript
/*
|
||
STM32 F103 serial bus seems to properly initialize with quite a huge auto-baud range
|
||
From 921600 down to 1200, i don't recommend getting any lower then that
|
||
Official "specs" are from 115200 to 1200
|
||
|
||
popular choices - 921600, 460800, 256000, 230400, 153600, 128000, 115200, 57600, 38400, 28800, 19200
|
||
*/
|
||
'use strict';
|
||
|
||
var STM32_protocol = function () {
|
||
this.baud;
|
||
this.options = {};
|
||
this.callback; // ref
|
||
this.hex; // ref
|
||
this.verify_hex;
|
||
|
||
this.receive_buffer;
|
||
|
||
this.bytes_to_read = 0; // ref
|
||
this.read_callback; // ref
|
||
|
||
this.upload_time_start;
|
||
this.upload_process_alive;
|
||
|
||
this.status = {
|
||
ACK: 0x79, // y
|
||
NACK: 0x1F
|
||
};
|
||
|
||
this.command = {
|
||
get: 0x00, // Gets the version and the allowed commands supported by the current version of the bootloader
|
||
get_ver_r_protect_s: 0x01, // Gets the bootloader version and the Read Protection status of the Flash memory
|
||
get_ID: 0x02, // Gets the chip ID
|
||
read_memory: 0x11, // Reads up to 256 bytes of memory starting from an address specified by the application
|
||
go: 0x21, // Jumps to user application code located in the internal Flash memory or in SRAM
|
||
write_memory: 0x31, // Writes up to 256 bytes to the RAM or Flash memory starting from an address specified by the application
|
||
erase: 0x43, // Erases from one to all the Flash memory pages
|
||
extended_erase: 0x44, // Erases from one to all the Flash memory pages using two byte addressing mode (v3.0+ usart).
|
||
write_protect: 0x63, // Enables the write protection for some sectors
|
||
write_unprotect: 0x73, // Disables the write protection for all Flash memory sectors
|
||
readout_protect: 0x82, // Enables the read protection
|
||
readout_unprotect: 0x92 // Disables the read protection
|
||
};
|
||
|
||
// Erase (x043) and Extended Erase (0x44) are exclusive. A device may support either the Erase command or the Extended Erase command but not both.
|
||
|
||
this.available_flash_size = 0;
|
||
this.page_size = 0;
|
||
this.useExtendedErase = false;
|
||
};
|
||
|
||
// no input parameters
|
||
STM32_protocol.prototype.connect = function (port, baud, hex, options, callback) {
|
||
var self = this;
|
||
self.hex = hex;
|
||
self.baud = baud;
|
||
self.callback = callback;
|
||
|
||
// we will crunch the options here since doing it inside initialization routine would be too late
|
||
self.options = {
|
||
no_reboot: false,
|
||
reboot_baud: false,
|
||
erase_chip: false
|
||
};
|
||
|
||
if (options.no_reboot) {
|
||
self.options.no_reboot = true;
|
||
} else {
|
||
self.options.reboot_baud = options.reboot_baud;
|
||
}
|
||
|
||
if (options.erase_chip) {
|
||
self.options.erase_chip = true;
|
||
}
|
||
|
||
if (self.options.no_reboot) {
|
||
serial.connect(port, {bitrate: self.baud, parityBit: 'even', stopBits: 'one'}, function (openInfo) {
|
||
if (openInfo) {
|
||
// we are connected, disabling connect button in the UI
|
||
GUI.connect_lock = true;
|
||
|
||
self.initialize();
|
||
} else {
|
||
GUI.log('<span style="color: red">Failed</span> to open serial port');
|
||
}
|
||
});
|
||
} else {
|
||
serial.connect(port, {bitrate: self.options.reboot_baud}, function (openInfo) {
|
||
if (openInfo) {
|
||
console.log('Sending ascii "R" to reboot');
|
||
|
||
// we are connected, disabling connect button in the UI
|
||
GUI.connect_lock = true;
|
||
|
||
var bufferOut = new ArrayBuffer(1);
|
||
var bufferView = new Uint8Array(bufferOut);
|
||
|
||
bufferView[0] = 0x52;
|
||
|
||
serial.send(bufferOut, function () {
|
||
serial.disconnect(function (result) {
|
||
if (result) {
|
||
// delay to allow board to boot in bootloader mode
|
||
// required to detect if a DFU device appears
|
||
setTimeout(function() {
|
||
// refresh device list
|
||
PortHandler.check_usb_devices(function(dfu_available) {
|
||
if(dfu_available) {
|
||
STM32DFU.connect(usbDevices.STM32DFU, hex, options);
|
||
} else {
|
||
serial.connect(port, {bitrate: self.baud, parityBit: 'even', stopBits: 'one'}, function (openInfo) {
|
||
if (openInfo) {
|
||
self.initialize();
|
||
} else {
|
||
GUI.connect_lock = false;
|
||
GUI.log('<span style="color: red">Failed</span> to open serial port');
|
||
}
|
||
});
|
||
}
|
||
});
|
||
}, 1000);
|
||
} else {
|
||
GUI.connect_lock = false;
|
||
}
|
||
});
|
||
});
|
||
} else {
|
||
GUI.log('<span style="color: red">Failed</span> to open serial port');
|
||
}
|
||
});
|
||
}
|
||
};
|
||
|
||
// initialize certain variables and start timers that oversee the communication
|
||
STM32_protocol.prototype.initialize = function () {
|
||
var self = this;
|
||
|
||
// reset and set some variables before we start
|
||
self.receive_buffer = [];
|
||
self.verify_hex = [];
|
||
|
||
self.upload_time_start = new Date().getTime();
|
||
self.upload_process_alive = false;
|
||
|
||
// reset progress bar to initial state
|
||
self.progress_bar_e = $('.progress');
|
||
self.progress_bar_e.val(0);
|
||
self.progress_bar_e.removeClass('valid invalid');
|
||
|
||
// lock some UI elements TODO needs rework
|
||
$('select[name="release"]').prop('disabled', true);
|
||
|
||
serial.onReceive.addListener(function (info) {
|
||
self.read(info);
|
||
});
|
||
|
||
GUI.interval_add('STM32_timeout', function () {
|
||
if (self.upload_process_alive) { // process is running
|
||
self.upload_process_alive = false;
|
||
} else {
|
||
console.log('STM32 - timed out, programming failed ...');
|
||
|
||
$('span.progressLabel').text('STM32 - timed out, programming: FAILED');
|
||
self.progress_bar_e.addClass('invalid');
|
||
|
||
googleAnalytics.sendEvent('Flashing', 'Programming', 'timeout');
|
||
|
||
// protocol got stuck, clear timer and disconnect
|
||
GUI.interval_remove('STM32_timeout');
|
||
|
||
// exit
|
||
self.upload_procedure(99);
|
||
}
|
||
}, 2000);
|
||
|
||
self.upload_procedure(1);
|
||
};
|
||
|
||
// no input parameters
|
||
// this method should be executed every 1 ms via interval timer
|
||
STM32_protocol.prototype.read = function (readInfo) {
|
||
// routine that fills the buffer
|
||
var data = new Uint8Array(readInfo.data);
|
||
|
||
for (var i = 0; i < data.length; i++) {
|
||
this.receive_buffer.push(data[i]);
|
||
}
|
||
|
||
// routine that fetches data from buffer if statement is true
|
||
if (this.receive_buffer.length >= this.bytes_to_read && this.bytes_to_read != 0) {
|
||
var data = this.receive_buffer.slice(0, this.bytes_to_read); // bytes requested
|
||
this.receive_buffer.splice(0, this.bytes_to_read); // remove read bytes
|
||
|
||
this.bytes_to_read = 0; // reset trigger
|
||
|
||
this.read_callback(data);
|
||
}
|
||
};
|
||
|
||
// we should always try to consume all "proper" available data while using retrieve
|
||
STM32_protocol.prototype.retrieve = function (n_bytes, callback) {
|
||
if (this.receive_buffer.length >= n_bytes) {
|
||
// data that we need are there, process immediately
|
||
var data = this.receive_buffer.slice(0, n_bytes);
|
||
this.receive_buffer.splice(0, n_bytes); // remove read bytes
|
||
|
||
callback(data);
|
||
} else {
|
||
// still waiting for data, add callback
|
||
this.bytes_to_read = n_bytes;
|
||
this.read_callback = callback;
|
||
}
|
||
};
|
||
|
||
// Array = array of bytes that will be send over serial
|
||
// bytes_to_read = received bytes necessary to trigger read_callback
|
||
// callback = function that will be executed after received bytes = bytes_to_read
|
||
STM32_protocol.prototype.send = function (Array, bytes_to_read, callback) {
|
||
// flip flag
|
||
this.upload_process_alive = true;
|
||
|
||
var bufferOut = new ArrayBuffer(Array.length);
|
||
var bufferView = new Uint8Array(bufferOut);
|
||
|
||
// set Array values inside bufferView (alternative to for loop)
|
||
bufferView.set(Array);
|
||
|
||
// update references
|
||
this.bytes_to_read = bytes_to_read;
|
||
this.read_callback = callback;
|
||
|
||
// empty receive buffer before next command is out
|
||
this.receive_buffer = [];
|
||
|
||
// send over the actual data
|
||
serial.send(bufferOut, function (writeInfo) {});
|
||
};
|
||
|
||
// val = single byte to be verified
|
||
// data = response of n bytes from mcu (array)
|
||
// result = true/false
|
||
STM32_protocol.prototype.verify_response = function (val, data) {
|
||
var self = this;
|
||
|
||
if (val != data[0]) {
|
||
var message = 'STM32 Communication failed, wrong response, expected: ' + val + ' (0x' + val.toString(16) + ') received: ' + data[0] + ' (0x' + data[0].toString(16) + ')';
|
||
console.error(message);
|
||
$('span.progressLabel').text(message);
|
||
self.progress_bar_e.addClass('invalid');
|
||
|
||
// disconnect
|
||
this.upload_procedure(99);
|
||
|
||
return false;
|
||
}
|
||
|
||
return true;
|
||
};
|
||
|
||
// input = 16 bit value
|
||
// result = true/false
|
||
STM32_protocol.prototype.verify_chip_signature = function (signature) {
|
||
switch (signature) {
|
||
case 0x412: // not tested
|
||
console.log('Chip recognized as F1 Low-density');
|
||
break;
|
||
case 0x410:
|
||
console.log('Chip recognized as F1 Medium-density');
|
||
this.available_flash_size = 131072;
|
||
this.page_size = 1024;
|
||
break;
|
||
case 0x414: // not tested
|
||
console.log('Chip recognized as F1 High-density');
|
||
break;
|
||
case 0x418: // not tested
|
||
console.log('Chip recognized as F1 Connectivity line');
|
||
break;
|
||
case 0x420: // not tested
|
||
console.log('Chip recognized as F1 Medium-density value line');
|
||
break;
|
||
case 0x428: // not tested
|
||
console.log('Chip recognized as F1 High-density value line');
|
||
break;
|
||
case 0x430: // not tested
|
||
console.log('Chip recognized as F1 XL-density value line');
|
||
break;
|
||
case 0x416: // not tested
|
||
console.log('Chip recognized as L1 Medium-density ultralow power');
|
||
break;
|
||
case 0x436: // not tested
|
||
console.log('Chip recognized as L1 High-density ultralow power');
|
||
break;
|
||
case 0x427: // not tested
|
||
console.log('Chip recognized as L1 Medium-density plus ultralow power');
|
||
break;
|
||
case 0x411: // not tested
|
||
console.log('Chip recognized as F2 STM32F2xxxx');
|
||
break;
|
||
case 0x440: // not tested
|
||
console.log('Chip recognized as F0 STM32F051xx');
|
||
break;
|
||
case 0x444: // not tested
|
||
console.log('Chip recognized as F0 STM32F050xx');
|
||
break;
|
||
case 0x413: // not tested
|
||
console.log('Chip recognized as F4 STM32F40xxx/41xxx');
|
||
break;
|
||
case 0x419: // not tested
|
||
console.log('Chip recognized as F4 STM32F427xx/437xx, STM32F429xx/439xx');
|
||
break;
|
||
case 0x432: // not tested
|
||
console.log('Chip recognized as F3 STM32F37xxx, STM32F38xxx');
|
||
break;
|
||
case 0x422:
|
||
console.log('Chip recognized as F3 STM32F30xxx, STM32F31xxx');
|
||
this.available_flash_size = 0x40000;
|
||
this.page_size = 2048;
|
||
break;
|
||
}
|
||
|
||
if (this.available_flash_size > 0) {
|
||
if (this.hex.bytes_total < this.available_flash_size) {
|
||
return true;
|
||
} else {
|
||
console.log('Supplied hex is bigger then flash available on the chip, HEX: ' + this.hex.bytes_total + ' bytes, limit = ' + this.available_flash_size + ' bytes');
|
||
|
||
return false;
|
||
}
|
||
}
|
||
|
||
console.log('Chip NOT recognized: ' + signature);
|
||
|
||
return false;
|
||
};
|
||
|
||
// first_array = usually hex_to_flash array
|
||
// second_array = usually verify_hex array
|
||
// result = true/false
|
||
STM32_protocol.prototype.verify_flash = function (first_array, second_array) {
|
||
for (var i = 0; i < first_array.length; i++) {
|
||
if (first_array[i] != second_array[i]) {
|
||
console.log('Verification failed on byte: ' + i + ' expected: 0x' + first_array[i].toString(16) + ' received: 0x' + second_array[i].toString(16));
|
||
return false;
|
||
}
|
||
}
|
||
|
||
console.log('Verification successful, matching: ' + first_array.length + ' bytes');
|
||
|
||
return true;
|
||
};
|
||
|
||
// step = value depending on current state of upload_procedure
|
||
STM32_protocol.prototype.upload_procedure = function (step) {
|
||
var self = this;
|
||
|
||
switch (step) {
|
||
case 1:
|
||
// initialize serial interface on the MCU side, auto baud rate settings
|
||
$('span.progressLabel').text('Contacting bootloader ...');
|
||
|
||
var send_counter = 0;
|
||
GUI.interval_add('stm32_initialize_mcu', function () { // 200 ms interval (just in case mcu was already initialized), we need to break the 2 bytes command requirement
|
||
self.send([0x7F], 1, function (reply) {
|
||
if (reply[0] == 0x7F || reply[0] == self.status.ACK || reply[0] == self.status.NACK) {
|
||
GUI.interval_remove('stm32_initialize_mcu');
|
||
console.log('STM32 - Serial interface initialized on the MCU side');
|
||
|
||
// proceed to next step
|
||
self.upload_procedure(2);
|
||
} else {
|
||
$('span.progressLabel').text('Communication with bootloader failed');
|
||
self.progress_bar_e.addClass('invalid');
|
||
|
||
GUI.interval_remove('stm32_initialize_mcu');
|
||
|
||
// disconnect
|
||
self.upload_procedure(99);
|
||
}
|
||
});
|
||
|
||
if (send_counter++ > 3) {
|
||
// stop retrying, its too late to get any response from MCU
|
||
console.log('STM32 - no response from bootloader, disconnecting');
|
||
|
||
$('span.progressLabel').text('No response from the bootloader, programming: FAILED');
|
||
self.progress_bar_e.addClass('invalid');
|
||
|
||
GUI.interval_remove('stm32_initialize_mcu');
|
||
GUI.interval_remove('STM32_timeout');
|
||
|
||
// exit
|
||
self.upload_procedure(99);
|
||
}
|
||
}, 250, true);
|
||
break;
|
||
case 2:
|
||
// get version of the bootloader and supported commands
|
||
self.send([self.command.get, 0xFF], 2, function (data) { // 0x00 ^ 0xFF
|
||
if (self.verify_response(self.status.ACK, data)) {
|
||
self.retrieve(data[1] + 1 + 1, function (data) { // data[1] = number of bytes that will follow [– 1 except current and ACKs]
|
||
console.log('STM32 - Bootloader version: ' + (parseInt(data[0].toString(16)) / 10).toFixed(1)); // convert dec to hex, hex to dec and add floating point
|
||
|
||
self.useExtendedErase = (data[7] == self.command.extended_erase);
|
||
|
||
// proceed to next step
|
||
self.upload_procedure(3);
|
||
});
|
||
}
|
||
});
|
||
break;
|
||
case 3:
|
||
// get ID (device signature)
|
||
self.send([self.command.get_ID, 0xFD], 2, function (data) { // 0x01 ^ 0xFF
|
||
if (self.verify_response(self.status.ACK, data)) {
|
||
self.retrieve(data[1] + 1 + 1, function (data) { // data[1] = number of bytes that will follow [– 1 (N = 1 for STM32), except for current byte and ACKs]
|
||
var signature = (data[0] << 8) | data[1];
|
||
console.log('STM32 - Signature: 0x' + signature.toString(16)); // signature in hex representation
|
||
|
||
if (self.verify_chip_signature(signature)) {
|
||
// proceed to next step
|
||
self.upload_procedure(4);
|
||
} else {
|
||
// disconnect
|
||
self.upload_procedure(99);
|
||
}
|
||
});
|
||
}
|
||
});
|
||
break;
|
||
case 4:
|
||
// erase memory
|
||
|
||
if (self.useExtendedErase) {
|
||
if (self.options.erase_chip) {
|
||
|
||
var message = 'Executing global chip erase (via extended erase)';
|
||
console.log(message);
|
||
$('span.progressLabel').text(message + ' ...');
|
||
|
||
self.send([self.command.extended_erase, 0xBB], 1, function (reply) {
|
||
if (self.verify_response(self.status.ACK, reply)) {
|
||
self.send( [0xFF, 0xFF, 0x00], 1, function (reply) {
|
||
if (self.verify_response(self.status.ACK, reply)) {
|
||
console.log('Executing global chip extended erase: done');
|
||
self.upload_procedure(5);
|
||
}
|
||
});
|
||
}
|
||
});
|
||
|
||
} else {
|
||
var message = 'Executing local erase (via extended erase)';
|
||
console.log(message);
|
||
$('span.progressLabel').text(message + ' ...');
|
||
|
||
self.send([self.command.extended_erase, 0xBB], 1, function (reply) {
|
||
if (self.verify_response(self.status.ACK, reply)) {
|
||
|
||
// For reference: https://code.google.com/p/stm32flash/source/browse/stm32.c#723
|
||
|
||
var max_address = self.hex.data[self.hex.data.length - 1].address + self.hex.data[self.hex.data.length - 1].bytes - 0x8000000,
|
||
erase_pages_n = Math.ceil(max_address / self.page_size),
|
||
buff = [],
|
||
checksum = 0;
|
||
|
||
var pg_byte;
|
||
|
||
pg_byte = (erase_pages_n - 1) >> 8;
|
||
buff.push(pg_byte);
|
||
checksum ^= pg_byte;
|
||
pg_byte = (erase_pages_n - 1) & 0xFF;
|
||
buff.push(pg_byte);
|
||
checksum ^= pg_byte;
|
||
|
||
|
||
for (var i = 0; i < erase_pages_n; i++) {
|
||
pg_byte = i >> 8;
|
||
buff.push(pg_byte);
|
||
checksum ^= pg_byte;
|
||
pg_byte = i & 0xFF;
|
||
buff.push(pg_byte);
|
||
checksum ^= pg_byte;
|
||
}
|
||
|
||
buff.push(checksum);
|
||
console.log('Erasing. pages: 0x00 - 0x' + erase_pages_n.toString(16) + ', checksum: 0x' + checksum.toString(16));
|
||
|
||
self.send(buff, 1, function (reply) {
|
||
if (self.verify_response(self.status.ACK, reply)) {
|
||
console.log('Erasing: done');
|
||
// proceed to next step
|
||
self.upload_procedure(5);
|
||
}
|
||
});
|
||
}
|
||
});
|
||
|
||
|
||
}
|
||
break;
|
||
}
|
||
|
||
if (self.options.erase_chip) {
|
||
var message = 'Executing global chip erase' ;
|
||
console.log(message);
|
||
$('span.progressLabel').text(message + ' ...');
|
||
|
||
self.send([self.command.erase, 0xBC], 1, function (reply) { // 0x43 ^ 0xFF
|
||
if (self.verify_response(self.status.ACK, reply)) {
|
||
self.send([0xFF, 0x00], 1, function (reply) {
|
||
if (self.verify_response(self.status.ACK, reply)) {
|
||
console.log('Erasing: done');
|
||
// proceed to next step
|
||
self.upload_procedure(5);
|
||
}
|
||
});
|
||
}
|
||
});
|
||
} else {
|
||
var message = 'Executing local erase';
|
||
console.log(message);
|
||
$('span.progressLabel').text(message + ' ...');
|
||
|
||
self.send([self.command.erase, 0xBC], 1, function (reply) { // 0x43 ^ 0xFF
|
||
if (self.verify_response(self.status.ACK, reply)) {
|
||
// the bootloader receives one byte that contains N, the number of pages to be erased – 1
|
||
var max_address = self.hex.data[self.hex.data.length - 1].address + self.hex.data[self.hex.data.length - 1].bytes - 0x8000000,
|
||
erase_pages_n = Math.ceil(max_address / self.page_size),
|
||
buff = [],
|
||
checksum = erase_pages_n - 1;
|
||
|
||
buff.push(erase_pages_n - 1);
|
||
|
||
for (var i = 0; i < erase_pages_n; i++) {
|
||
buff.push(i);
|
||
checksum ^= i;
|
||
}
|
||
|
||
buff.push(checksum);
|
||
|
||
self.send(buff, 1, function (reply) {
|
||
if (self.verify_response(self.status.ACK, reply)) {
|
||
console.log('Erasing: done');
|
||
// proceed to next step
|
||
self.upload_procedure(5);
|
||
}
|
||
});
|
||
}
|
||
});
|
||
}
|
||
break;
|
||
case 5:
|
||
// upload
|
||
console.log('Writing data ...');
|
||
$('span.progressLabel').text('Flashing ...');
|
||
|
||
var blocks = self.hex.data.length - 1,
|
||
flashing_block = 0,
|
||
address = self.hex.data[flashing_block].address,
|
||
bytes_flashed = 0,
|
||
bytes_flashed_total = 0; // used for progress bar
|
||
|
||
var write = function () {
|
||
if (bytes_flashed < self.hex.data[flashing_block].bytes) {
|
||
var bytes_to_write = ((bytes_flashed + 256) <= self.hex.data[flashing_block].bytes) ? 256 : (self.hex.data[flashing_block].bytes - bytes_flashed);
|
||
|
||
// console.log('STM32 - Writing to: 0x' + address.toString(16) + ', ' + bytes_to_write + ' bytes');
|
||
|
||
self.send([self.command.write_memory, 0xCE], 1, function (reply) { // 0x31 ^ 0xFF
|
||
if (self.verify_response(self.status.ACK, reply)) {
|
||
// address needs to be transmitted as 32 bit integer, we need to bit shift each byte out and then calculate address checksum
|
||
var address_arr = [(address >> 24), (address >> 16), (address >> 8), address];
|
||
var address_checksum = address_arr[0] ^ address_arr[1] ^ address_arr[2] ^ address_arr[3];
|
||
|
||
self.send([address_arr[0], address_arr[1], address_arr[2], address_arr[3], address_checksum], 1, function (reply) { // write start address + checksum
|
||
if (self.verify_response(self.status.ACK, reply)) {
|
||
var array_out = new Array(bytes_to_write + 2); // 2 byte overhead [N, ...., checksum]
|
||
array_out[0] = bytes_to_write - 1; // number of bytes to be written (to write 128 bytes, N must be 127, to write 256 bytes, N must be 255)
|
||
|
||
var checksum = array_out[0];
|
||
for (var i = 0; i < bytes_to_write; i++) {
|
||
array_out[i + 1] = self.hex.data[flashing_block].data[bytes_flashed]; // + 1 because of the first byte offset
|
||
checksum ^= self.hex.data[flashing_block].data[bytes_flashed];
|
||
|
||
bytes_flashed++;
|
||
}
|
||
array_out[array_out.length - 1] = checksum; // checksum (last byte in the array_out array)
|
||
|
||
address += bytes_to_write;
|
||
bytes_flashed_total += bytes_to_write;
|
||
|
||
self.send(array_out, 1, function (reply) {
|
||
if (self.verify_response(self.status.ACK, reply)) {
|
||
// flash another page
|
||
write();
|
||
}
|
||
});
|
||
|
||
// update progress bar
|
||
self.progress_bar_e.val(Math.round(bytes_flashed_total / (self.hex.bytes_total * 2) * 100));
|
||
}
|
||
});
|
||
}
|
||
});
|
||
} else {
|
||
// move to another block
|
||
if (flashing_block < blocks) {
|
||
flashing_block++;
|
||
|
||
address = self.hex.data[flashing_block].address;
|
||
bytes_flashed = 0;
|
||
|
||
write();
|
||
} else {
|
||
// all blocks flashed
|
||
console.log('Writing: done');
|
||
|
||
// proceed to next step
|
||
self.upload_procedure(6);
|
||
}
|
||
}
|
||
}
|
||
|
||
// start writing
|
||
write();
|
||
break;
|
||
case 6:
|
||
// verify
|
||
console.log('Verifying data ...');
|
||
$('span.progressLabel').text('Verifying ...');
|
||
|
||
var blocks = self.hex.data.length - 1,
|
||
reading_block = 0,
|
||
address = self.hex.data[reading_block].address,
|
||
bytes_verified = 0,
|
||
bytes_verified_total = 0; // used for progress bar
|
||
|
||
// initialize arrays
|
||
for (var i = 0; i <= blocks; i++) {
|
||
self.verify_hex.push([]);
|
||
}
|
||
|
||
var reading = function () {
|
||
if (bytes_verified < self.hex.data[reading_block].bytes) {
|
||
var bytes_to_read = ((bytes_verified + 256) <= self.hex.data[reading_block].bytes) ? 256 : (self.hex.data[reading_block].bytes - bytes_verified);
|
||
|
||
// console.log('STM32 - Reading from: 0x' + address.toString(16) + ', ' + bytes_to_read + ' bytes');
|
||
|
||
self.send([self.command.read_memory, 0xEE], 1, function (reply) { // 0x11 ^ 0xFF
|
||
if (self.verify_response(self.status.ACK, reply)) {
|
||
var address_arr = [(address >> 24), (address >> 16), (address >> 8), address];
|
||
var address_checksum = address_arr[0] ^ address_arr[1] ^ address_arr[2] ^ address_arr[3];
|
||
|
||
self.send([address_arr[0], address_arr[1], address_arr[2], address_arr[3], address_checksum], 1, function (reply) { // read start address + checksum
|
||
if (self.verify_response(self.status.ACK, reply)) {
|
||
var bytes_to_read_n = bytes_to_read - 1;
|
||
|
||
self.send([bytes_to_read_n, (~bytes_to_read_n) & 0xFF], 1, function (reply) { // bytes to be read + checksum XOR(complement of bytes_to_read_n)
|
||
if (self.verify_response(self.status.ACK, reply)) {
|
||
self.retrieve(bytes_to_read, function (data) {
|
||
for (var i = 0; i < data.length; i++) {
|
||
self.verify_hex[reading_block].push(data[i]);
|
||
}
|
||
|
||
address += bytes_to_read;
|
||
bytes_verified += bytes_to_read;
|
||
bytes_verified_total += bytes_to_read;
|
||
|
||
// verify another page
|
||
reading();
|
||
});
|
||
}
|
||
});
|
||
|
||
// update progress bar
|
||
self.progress_bar_e.val(Math.round((self.hex.bytes_total + bytes_verified_total) / (self.hex.bytes_total * 2) * 100));
|
||
}
|
||
});
|
||
}
|
||
});
|
||
} else {
|
||
// move to another block
|
||
if (reading_block < blocks) {
|
||
reading_block++;
|
||
|
||
address = self.hex.data[reading_block].address;
|
||
bytes_verified = 0;
|
||
|
||
reading();
|
||
} else {
|
||
// all blocks read, verify
|
||
|
||
var verify = true;
|
||
for (var i = 0; i <= blocks; i++) {
|
||
verify = self.verify_flash(self.hex.data[i].data, self.verify_hex[i]);
|
||
|
||
if (!verify) break;
|
||
}
|
||
|
||
if (verify) {
|
||
console.log('Programming: SUCCESSFUL');
|
||
$('span.progressLabel').text('Programming: SUCCESSFUL');
|
||
googleAnalytics.sendEvent('Flashing', 'Programming', 'success');
|
||
|
||
// update progress bar
|
||
self.progress_bar_e.addClass('valid');
|
||
|
||
// proceed to next step
|
||
self.upload_procedure(7);
|
||
} else {
|
||
console.log('Programming: FAILED');
|
||
$('span.progressLabel').text('Programming: FAILED');
|
||
googleAnalytics.sendEvent('Flashing', 'Programming', 'fail');
|
||
|
||
// update progress bar
|
||
self.progress_bar_e.addClass('invalid');
|
||
|
||
// disconnect
|
||
self.upload_procedure(99);
|
||
}
|
||
}
|
||
}
|
||
}
|
||
|
||
// start reading
|
||
reading();
|
||
break;
|
||
case 7:
|
||
// go
|
||
// memory address = 4 bytes, 1st high byte, 4th low byte, 5th byte = checksum XOR(byte 1, byte 2, byte 3, byte 4)
|
||
console.log('Sending GO command: 0x8000000');
|
||
|
||
self.send([self.command.go, 0xDE], 1, function (reply) { // 0x21 ^ 0xFF
|
||
if (self.verify_response(self.status.ACK, reply)) {
|
||
var gt_address = 0x8000000,
|
||
address = [(gt_address >> 24), (gt_address >> 16), (gt_address >> 8), gt_address],
|
||
address_checksum = address[0] ^ address[1] ^ address[2] ^ address[3];
|
||
|
||
self.send([address[0], address[1], address[2], address[3], address_checksum], 1, function (reply) {
|
||
if (self.verify_response(self.status.ACK, reply)) {
|
||
// disconnect
|
||
self.upload_procedure(99);
|
||
}
|
||
});
|
||
}
|
||
});
|
||
break;
|
||
case 99:
|
||
// disconnect
|
||
GUI.interval_remove('STM32_timeout'); // stop STM32 timeout timer (everything is finished now)
|
||
|
||
// close connection
|
||
serial.disconnect(function (result) {
|
||
PortUsage.reset();
|
||
|
||
// unlocking connect button
|
||
GUI.connect_lock = false;
|
||
|
||
// unlock some UI elements TODO needs rework
|
||
$('select[name="release"]').prop('disabled', false);
|
||
|
||
// handle timing
|
||
var timeSpent = new Date().getTime() - self.upload_time_start;
|
||
|
||
console.log('Script finished after: ' + (timeSpent / 1000) + ' seconds');
|
||
|
||
if (self.callback) self.callback();
|
||
});
|
||
break;
|
||
}
|
||
};
|
||
|
||
// initialize object
|
||
var STM32 = new STM32_protocol(); |