function tab_initialize_initial_setup() {
    ga_tracker.sendAppView('Initial Setup');
    GUI.active_tab = 'initial_setup';
    
    send_message(MSP_codes.MSP_IDENT, MSP_codes.MSP_IDENT, false, function() {
        send_message(MSP_codes.MSP_ACC_TRIM, MSP_codes.MSP_ACC_TRIM, false, function() {
            send_message(MSP_codes.MSP_MISC, MSP_codes.MSP_MISC, false, function() {
                var yaw_fix = 0.0;
                
                // Fill in misc stuff
                $('input[name="mincellvoltage"]').val(MISC.vbatmincellvoltage);
                $('input[name="maxcellvoltage"]').val(MISC.vbatmaxcellvoltage);
                $('input[name="voltagescale"]').val(MISC.vbatscale);
                
                $('input[name="minthrottle"]').val(MISC.minthrottle);
                $('input[name="maxthrottle"]').val(MISC.maxthrottle);
                $('input[name="failsafe_throttle"]').val(MISC.failsafe_throttle);
                $('input[name="mincommand"]').val(MISC.mincommand);
                
                $('input[name="mag_declination"]').val(MISC.mag_declination / 10);
                
                // Fill in the accel trimms from CONFIG object
                $('input[name="pitch"]').val(CONFIG.accelerometerTrims[0]);
                $('input[name="roll"]').val(CONFIG.accelerometerTrims[1]);
                
                // Display multiType
                var str = '';
                switch (CONFIG.multiType) {
                    case 1: // TRI
                        str = 'TRI';
                        break;
                    case 2: // QUAD +
                        str = 'Quad +';
                        break;
                    case 3: // QUAD X
                        str = 'Quad X';
                        break;
                    case 4: // BI
                        str = 'BI';
                        break;
                    case 5: // GIMBAL
                        str = 'Gimbal';
                        break;
                    case 6: // Y6
                        str = 'Y6';
                        break;
                    case 7: // HEX 6
                        str = 'HEX 6';
                        break;
                    case 8: // FLYING_WING
                        str = 'Flying Wing';
                        break;
                    case 9: // Y4
                        str = 'Y4';
                        break;
                    case 10: // HEX6 X
                        str = 'HEX6 X';
                        break;
                    case 11: // OCTO X8
                    case 12:
                    case 13:
                        str = 'OCTO X8';
                        break;
                    case 14: // AIRPLANE
                        str = 'Airplane';
                        break;
                    case 15: // Heli 120 
                        str = 'Heli 120';
                        break;
                    case 16: // Heli 90 
                        str = 'Heli 90';
                        break;
                    case 17: // Vtail 
                        str = 'Vtail';
                        break;
                    case 18: // HEX6 H
                        str = 'HEX6 H';
                        break;
                    case 19: // PPM to SERVO
                        str = 'PPM to SERVO';
                        break;
                    case 20: // Dualcopter
                        str = 'Dualcopter';
                        break;
                    case 21: //
                        str = 'Singlecopter';
                        break;
                }
                
                $('span.model').html('Model: ' + str);
                
                // UI Hooks
                $('a.calibrateAccel').click(function() {
                    var self = $(this);
                    
                    if (!self.hasClass('calibrating')) {
                        self.addClass('calibrating');
                        
                        // During this period MCU won't be able to process any serial commands because its locked in a for/while loop
                        // until this operation finishes, sending more commands through data_poll() will result in serial buffer overflow
                        GUI.interval_pause('initial_setup_data_pull');
                        send_message(MSP_codes.MSP_ACC_CALIBRATION, MSP_codes.MSP_ACC_CALIBRATION);
                        
                        GUI.timeout_add('button_reset', function() {
                            GUI.interval_resume('initial_setup_data_pull');
                            self.removeClass('calibrating');
                        }, 2000);
                    }
                });
                
                $('a.calibrateMag').click(function() {
                    var self = $(this);
                    
                    if (!self.hasClass('calibrating')) {
                        self.addClass('calibrating');
                    
                        send_message(MSP_codes.MSP_MAG_CALIBRATION, MSP_codes.MSP_MAG_CALIBRATION);
                        
                        GUI.timeout_add('button_reset', function() {
                            self.removeClass('calibrating');
                        }, 30000);
                    }
                });

                $('a.resetSettings').click(function() {
                    send_message(MSP_codes.MSP_RESET_CONF, MSP_codes.MSP_RESET_CONF);
                });

                
                $('a.save_settings').click(function() {
                    CONFIG.accelerometerTrims[0] = parseInt($('input[name="pitch"]').val());
                    CONFIG.accelerometerTrims[1] = parseInt($('input[name="roll"]').val());
                    
                    var buffer_out = new Array();
                    buffer_out[0] = lowByte(CONFIG.accelerometerTrims[0]);
                    buffer_out[1] = highByte(CONFIG.accelerometerTrims[0]);
                    buffer_out[2] = lowByte(CONFIG.accelerometerTrims[1]);
                    buffer_out[3] = highByte(CONFIG.accelerometerTrims[1]); 

                    // Send over the new trims
                    send_message(MSP_codes.MSP_SET_ACC_TRIM, buffer_out);
                    
                    MISC.vbatmincellvoltage = parseFloat($('input[name="mincellvoltage"]').val()) * 10;
                    MISC.vbatmaxcellvoltage = parseFloat($('input[name="maxcellvoltage"]').val()) * 10;
                    MISC.vbatscale = parseInt($('input[name="voltagescale"]').val());
                    
                    MISC.minthrottle = parseInt($('input[name="minthrottle"]').val());
                    MISC.maxthrottle = parseInt($('input[name="maxthrottle"]').val());
                    MISC.failsafe_throttle = parseInt($('input[name="failsafe_throttle"]').val());
                    MISC.mincommand = parseInt($('input[name="mincommand"]').val());
                    
                    MISC.mag_declination = parseFloat($('input[name="mag_declination"]').val()) * 10;
                    
                    // we also have to fill the unsupported bytes
                    var buffer_out = new Array();
                    buffer_out[0] = 0; // powerfailmeter
                    buffer_out[1] = 0;
                    buffer_out[2] = lowByte(MISC.minthrottle);
                    buffer_out[3] = highByte(MISC.minthrottle);
                    buffer_out[4] = lowByte(MISC.maxthrottle);
                    buffer_out[5] = highByte(MISC.maxthrottle);
                    buffer_out[6] = lowByte(MISC.mincommand);
                    buffer_out[7] = highByte(MISC.mincommand);
                    buffer_out[8] = lowByte(MISC.failsafe_throttle);
                    buffer_out[9] = highByte(MISC.failsafe_throttle);
                    buffer_out[10] = 0;
                    buffer_out[11] = 0;
                    buffer_out[12] = 0;
                    buffer_out[13] = 0;
                    buffer_out[14] = 0;
                    buffer_out[15] = 0;
                    buffer_out[16] = lowByte(MISC.mag_declination);
                    buffer_out[17] = highByte(MISC.mag_declination);
                    buffer_out[18] = MISC.vbatscale;
                    buffer_out[19] = MISC.vbatmincellvoltage;
                    buffer_out[20] = MISC.vbatmaxcellvoltage;
                    buffer_out[21] = 0; // vbatlevel_crit (unused)
                    
                    // Send over new misc
                    send_message(MSP_codes.MSP_SET_MISC, buffer_out);
                    
                    // Save changes to EEPROM
                    send_message(MSP_codes.MSP_EEPROM_WRITE, MSP_codes.MSP_EEPROM_WRITE);
                });    

                // reset yaw button hook
                $('div#interactive_block > a.reset').click(function() {
                    yaw_fix = SENSOR_DATA.kinematicsZ * - 1.0;
                    console.log("YAW reset to 0");
                });  

                $('#content .backup').click(configuration_backup);
                
                $('#content .restore').click(configuration_restore);
                
                GUI.interval_add('initial_setup_data_pull', function() {
                    // Update cube
                    var cube = $('div#cube');
                    
                    cube.css('-webkit-transform', 'rotateY(' + ((SENSOR_DATA.kinematicsZ * -1.0) - yaw_fix) + 'deg)');
                    $('#cubePITCH', cube).css('-webkit-transform', 'rotateX(' + SENSOR_DATA.kinematicsY + 'deg)');
                    $('#cubeROLL', cube).css('-webkit-transform', 'rotateZ(' + SENSOR_DATA.kinematicsX + 'deg)'); 

                    // Update Compass
                    $('div#compass .pointer').css('-webkit-transform', 'rotate(' + (SENSOR_DATA.kinematicsZ) + 'deg)'); 
                    $('div#compass .value').html(SENSOR_DATA.kinematicsZ + '°');
                    
                    // Update voltage indicator
                    $('.bat-voltage').html(BATTERY.voltage + ' V');
                    
                    // Request new data
                    send_message(MSP_codes.MSP_STATUS, MSP_codes.MSP_STATUS);
                    send_message(MSP_codes.MSP_ATTITUDE, MSP_codes.MSP_ATTITUDE); 
                    send_message(MSP_codes.MSP_COMP_GPS, MSP_codes.MSP_COMP_GPS);
                    send_message(MSP_codes.MSP_ANALOG, MSP_codes.MSP_ANALOG);
                }, 50, true);
            });
        });
    });
}