"message":"Please click on <strong>\"Request Optional Permissions\"</strong> button to grant application <strong style=\"color: red\">required</strong> <strong>USB</strong> access"
"message":"Due to addition of <strong>Naze32PRO</strong> to the supported hardware family, Configurator <strong style=\"color: red\">requires</strong> USB access to allow firmware flashing via DFU"
"message":"Welcome to <strong>Baseflight - Configurator</strong>, utility designed to simplify updating, configuring and tuning of your flight controller.<br />Application supports complete family of Baseflight hardware (acro naze, naze32, naze32pro and afromini).<br /><br /><strong>Official Resellers & Backers</strong><br />• <a href=\"http://www.abusemark.com/store/\" title=\"www.abusemark.com\" target=\"_blank\">AbuseMark</a> - International (Japan)<br />• <a href=\"http://www.multirotorsuperstore.com/\" title=\"www.multirotorsuperstore.com\" target=\"_blank\">Multirotor Superstore</a> - International (United States)<br /><br />Latest <strong>CP210x Drivers</strong> can be downloaded from <a href=\"http://www.silabs.com/products/mcu/pages/usbtouartbridgevcpdrivers.aspx\" title=\"http://www.silabs.com/\" target=\"_blank\">here</a><br />"
"message":"This utility is fully <strong>open source</strong> and is available free of charge to all <strong>baseflight</strong> users.<br />If you found the utility useful, please consider <strong>supporting</strong> its development by donating."
"message":"Place board or frame on <strong style=\"color: green\">leveled</strong> surface, proceed with calibration, ensure platform is <strong style=\"color: red\">not</strong> moving during calibration period."
},
"initialSetupButtonCalibrateMag":{
"message":"Calibrate Magnetometer"
},
"initialSetupCalibrateMagText":{
"message":"Move multirotor atleast <strong>360</strong> degrees on all axis of rotation. You have <strong style=\"color: red\">30 seconds</strong> to perform this task."
},
"initialSetupButtonReset":{
"message":"Reset Settings"
},
"initialSetupResetText":{
"message":"Restore <span style=\"color: red\">all</span> settings to <strong>default</strong>."
},
"initialSetupButtonBackup":{
"message":"Backup"
},
"initialSetupButtonRestore":{
"message":"Restore"
},
"initialSetupBackupRestoreText":{
"message":"<strong>Backup</strong> your configuration in case of an accident. (<strong>CLI</strong> settings are <strong style=\"color: red\">not</strong> included)."
"message":"<strong>Motor Test Mode Notice:</strong><br />Moving the sliders will cause the motors to <strong>spin up</strong>.<br />In order to prevent injury <strong style=\"color: red\">remove ALL propellers</strong> before using this feature.<br />If you understand these instructions check the <strong>box</strong> below to <strong style=\"color: green\">enable</strong> motor test.<br /><br /><label>Check: <input type=\"checkbox\" /></label>"
"message":"Keep in mind that using fast update periods and rendering multiple graphs at the same time is resource heavy and will burn your battery quicker if you use a laptop.<br />We recommend to only render graphs for sensors you are interested in while using reasonable update periods."
"message":"<span style=\"color: red\">Note</span>: Leaving CLI tab or pressing Disconnect will <strong>automatically</strong> send \"<strong>exit</strong>\" to the board, which will make the controller save all the changes and <span style=\"color: red\">restart</span>."
"message":"Data will be logged in this tab <span style=\"color: red\">only</span>, leaving the tab will <span style=\"color: red\">cancel</span> logging and application will return to its normal <strong>\"configurator\"</strong> state.<br /> You are free to select the global update period, data will be written into the log file every <strong>1</strong> second for performance reasons."
"message":"If you are flashing board with bootloader pins <strong>shorted/connected</strong>, check <strong>No reboot sequence</strong>.<br />If you want configuration data to be wiped, check <strong>Full Chip Erase</strong><br />"
"message":"Please do not try to flash <strong>non-baseflight</strong> hardware with this firmware flasher (it wont work).<br />Do not <strong>disconnect</strong> the board or <strong>turn off</strong> your computer while flashing.<br /><br />Note: <strong>STM32</strong> bootloader is stored in <strong>ROM</strong>, it cannot be bricked.<br />Note: <strong>Auto-Connect</strong> is always disabled while you are inside firmware flasher.<br />"
},
"firmwareFlasherButtonLeave":{
"message":"Leave Firmware Flasher"
},
"firmwareFlasherFirmwareNotLoaded":{
"message":"<span style=\"color: red\">Firmware not loaded</span>"
