hak5
/
wifipineapple-openwrt
mirror of https://github.com/hak5/wifipineapple-openwrt.git
1
0
Fork 0
Code Issues Packages Projects Releases Wiki Activity
wifipineapple-openwrt/target/linux/ixp4xx/patches-2.6.37/110-pronghorn_series_suppor...

384 lines
10 KiB
Diff
Raw Blame History

--- a/arch/arm/configs/ixp4xx_defconfig
+++ b/arch/arm/configs/ixp4xx_defconfig
@@ -15,6 +15,8 @@ CONFIG_ARCH_ADI_COYOTE=y
CONFIG_MACH_GATEWAY7001=y
CONFIG_MACH_WG302V1=y
CONFIG_MACH_WG302V2=y
+CONFIG_MACH_PRONGHORN=y
+CONFIG_MACH_PRONGHORNMETRO=y
CONFIG_ARCH_IXDP425=y
CONFIG_MACH_IXDPG425=y
CONFIG_MACH_IXDP465=y
--- a/arch/arm/mach-ixp4xx/Kconfig
+++ b/arch/arm/mach-ixp4xx/Kconfig
@@ -65,6 +65,22 @@ config MACH_WG302V2
WG302 v2 or WAG302 v2 Access Points. For more information
on this platform, see http://openwrt.org
+config MACH_PRONGHORN
+ bool "ADI Pronghorn series"
+ select PCI
+ help
+ Say 'Y' here if you want your kernel to support the ADI
+ Engineering Pronghorn series. For more
+ information on this platform, see http://www.adiengineering.com
+
+#
+# There're only minimal differences kernel-wise between the Pronghorn and
+# Pronghorn Metro boards - they use different chip selects to drive the
+# CF slot connected to the expansion bus, so we just enable them together.
+#
+config MACH_PRONGHORNMETRO
+ def_bool MACH_PRONGHORN
+
config ARCH_IXDP425
bool "IXDP425"
help
--- a/arch/arm/mach-ixp4xx/Makefile
+++ b/arch/arm/mach-ixp4xx/Makefile
@@ -18,6 +18,7 @@ obj-pci-$(CONFIG_MACH_WG302V1) += wg302
obj-pci-$(CONFIG_MACH_WG302V2) += wg302v2-pci.o
obj-pci-$(CONFIG_MACH_FSG) += fsg-pci.o
obj-pci-$(CONFIG_MACH_ARCOM_VULCAN) += vulcan-pci.o
+obj-pci-$(CONFIG_MACH_PRONGHORN) += pronghorn-pci.o
obj-y += common.o
@@ -35,6 +36,7 @@ obj-$(CONFIG_MACH_WG302V2) += wg302v2-se
obj-$(CONFIG_MACH_FSG) += fsg-setup.o
obj-$(CONFIG_MACH_GORAMO_MLR) += goramo_mlr.o
obj-$(CONFIG_MACH_ARCOM_VULCAN) += vulcan-setup.o
+obj-$(CONFIG_MACH_PRONGHORN) += pronghorn-setup.o
obj-$(CONFIG_PCI) += $(obj-pci-$(CONFIG_PCI)) common-pci.o
obj-$(CONFIG_IXP4XX_QMGR) += ixp4xx_qmgr.o
--- /dev/null
+++ b/arch/arm/mach-ixp4xx/pronghorn-pci.c
@@ -0,0 +1,70 @@
+/*
+ * arch/arch/mach-ixp4xx/pronghorn-pci.c
+ *
+ * PCI setup routines for ADI Engineering Pronghorn series
+ *
+ * Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
+ *
+ * based on coyote-pci.c:
+ * Copyright (C) 2002 Jungo Software Technologies.
+ * Copyright (C) 2003 MontaVista Softwrae, Inc.
+ *
+ * Maintainer: Imre Kaloz <kaloz@openwrt.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/irq.h>
+
+#include <asm/mach-types.h>
+#include <mach/hardware.h>
+
+#include <asm/mach/pci.h>
+
+void __init pronghorn_pci_preinit(void)
+{
+ set_irq_type(IRQ_IXP4XX_GPIO4, IRQ_TYPE_LEVEL_LOW);
+ set_irq_type(IRQ_IXP4XX_GPIO6, IRQ_TYPE_LEVEL_LOW);
+ set_irq_type(IRQ_IXP4XX_GPIO11, IRQ_TYPE_LEVEL_LOW);
+ set_irq_type(IRQ_IXP4XX_GPIO1, IRQ_TYPE_LEVEL_LOW);
+
+ ixp4xx_pci_preinit();
+}
+
+static int __init pronghorn_map_irq(struct pci_dev *dev, u8 slot, u8 pin)
+{
+ if (slot == 13)
+ return IRQ_IXP4XX_GPIO4;
+ else if (slot == 14)
+ return IRQ_IXP4XX_GPIO6;
+ else if (slot == 15)
+ return IRQ_IXP4XX_GPIO11;
+ else if (slot == 16)
+ return IRQ_IXP4XX_GPIO1;
+ else
+ return -1;
+}
+
+struct hw_pci pronghorn_pci __initdata = {
+ .nr_controllers = 1,
+ .preinit = pronghorn_pci_preinit,
+ .swizzle = pci_std_swizzle,
+ .setup = ixp4xx_setup,
+ .scan = ixp4xx_scan_bus,
+ .map_irq = pronghorn_map_irq,
+};
+
+int __init pronghorn_pci_init(void)
+{
+ if (machine_is_pronghorn() || machine_is_pronghorn_metro())
+ pci_common_init(&pronghorn_pci);
+ return 0;
+}
+
+subsys_initcall(pronghorn_pci_init);
--- /dev/null
+++ b/arch/arm/mach-ixp4xx/pronghorn-setup.c
@@ -0,0 +1,241 @@
+/*
+ * arch/arm/mach-ixp4xx/pronghorn-setup.c
+ *
+ * Board setup for the ADI Engineering Pronghorn series
+ *
+ * Copyright (C) 2008 Imre Kaloz <Kaloz@openwrt.org>
+ *
+ * based on coyote-setup.c:
+ * Copyright (C) 2003-2005 MontaVista Software, Inc.
+ *
+ * Author: Imre Kaloz <Kaloz@openwrt.org>
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/device.h>
+#include <linux/serial.h>
+#include <linux/tty.h>
+#include <linux/serial_8250.h>
+#include <linux/slab.h>
+#include <linux/types.h>
+#include <linux/memory.h>
+#include <linux/i2c-gpio.h>
+#include <linux/leds.h>
+
+#include <asm/setup.h>
+#include <mach/hardware.h>
+#include <asm/irq.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/flash.h>
+
+static struct flash_platform_data pronghorn_flash_data = {
+ .map_name = "cfi_probe",
+ .width = 2,
+};
+
+static struct resource pronghorn_flash_resource = {
+ .flags = IORESOURCE_MEM,
+};
+
+static struct platform_device pronghorn_flash = {
+ .name = "IXP4XX-Flash",
+ .id = 0,
+ .dev = {
+ .platform_data = &pronghorn_flash_data,
+ },
+ .num_resources = 1,
+ .resource = &pronghorn_flash_resource,
+};
+
+static struct resource pronghorn_uart_resources [] = {
+ {
+ .start = IXP4XX_UART1_BASE_PHYS,
+ .end = IXP4XX_UART1_BASE_PHYS + 0x0fff,
+ .flags = IORESOURCE_MEM
+ },
+ {
+ .start = IXP4XX_UART2_BASE_PHYS,
+ .end = IXP4XX_UART2_BASE_PHYS + 0x0fff,
+ .flags = IORESOURCE_MEM
+ }
+};
+
+static struct plat_serial8250_port pronghorn_uart_data[] = {
+ {
+ .mapbase = IXP4XX_UART1_BASE_PHYS,
+ .membase = (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET,
+ .irq = IRQ_IXP4XX_UART1,
+ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
+ .iotype = UPIO_MEM,
+ .regshift = 2,
+ .uartclk = IXP4XX_UART_XTAL,
+ },
+ {
+ .mapbase = IXP4XX_UART2_BASE_PHYS,
+ .membase = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET,
+ .irq = IRQ_IXP4XX_UART2,
+ .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
+ .iotype = UPIO_MEM,
+ .regshift = 2,
+ .uartclk = IXP4XX_UART_XTAL,
+ },
+ { },
+};
+
+static struct platform_device pronghorn_uart = {
+ .name = "serial8250",
+ .id = PLAT8250_DEV_PLATFORM,
+ .dev = {
+ .platform_data = pronghorn_uart_data,
+ },
+ .num_resources = 2,
+ .resource = pronghorn_uart_resources,
+};
+
+static struct i2c_gpio_platform_data pronghorn_i2c_gpio_data = {
+ .sda_pin = 9,
+ .scl_pin = 10,
+};
+
+static struct platform_device pronghorn_i2c_gpio = {
+ .name = "i2c-gpio",
+ .id = 0,
+ .dev = {
+ .platform_data = &pronghorn_i2c_gpio_data,
+ },
+};
+
+static struct gpio_led pronghorn_led_pin[] = {
+ {
+ .name = "pronghorn:green:status",
+ .gpio = 7,
+ }
+};
+
+static struct gpio_led_platform_data pronghorn_led_data = {
+ .num_leds = 1,
+ .leds = pronghorn_led_pin,
+};
+
+static struct platform_device pronghorn_led = {
+ .name = "leds-gpio",
+ .id = -1,
+ .dev.platform_data = &pronghorn_led_data,
+};
+
+static struct resource pronghorn_pata_resources[] = {
+ {
+ .flags = IORESOURCE_MEM
+ },
+ {
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .name = "intrq",
+ .start = IRQ_IXP4XX_GPIO0,
+ .end = IRQ_IXP4XX_GPIO0,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct ixp4xx_pata_data pronghorn_pata_data = {
+ .cs0_bits = 0xbfff0043,
+ .cs1_bits = 0xbfff0043,
+};
+
+static struct platform_device pronghorn_pata = {
+ .name = "pata_ixp4xx_cf",
+ .id = 0,
+ .dev.platform_data = &pronghorn_pata_data,
+ .num_resources = ARRAY_SIZE(pronghorn_pata_resources),
+ .resource = pronghorn_pata_resources,
+};
+
+static struct eth_plat_info pronghorn_plat_eth[] = {
+ {
+ .phy = 0,
+ .rxq = 3,
+ .txreadyq = 20,
+ }, {
+ .phy = 1,
+ .rxq = 4,
+ .txreadyq = 21,
+ }
+};
+
+static struct platform_device pronghorn_eth[] = {
+ {
+ .name = "ixp4xx_eth",
+ .id = IXP4XX_ETH_NPEB,
+ .dev.platform_data = pronghorn_plat_eth,
+ }, {
+ .name = "ixp4xx_eth",
+ .id = IXP4XX_ETH_NPEC,
+ .dev.platform_data = pronghorn_plat_eth + 1,
+ }
+};
+
+static struct platform_device *pronghorn_devices[] __initdata = {
+ &pronghorn_flash,
+ &pronghorn_uart,
+ &pronghorn_led,
+ &pronghorn_eth[0],
+ &pronghorn_eth[1],
+};
+
+static void __init pronghorn_init(void)
+{
+ ixp4xx_sys_init();
+
+ pronghorn_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
+ pronghorn_flash_resource.end = IXP4XX_EXP_BUS_BASE(0) + SZ_32M - 1;
+
+ *IXP4XX_EXP_CS0 |= IXP4XX_FLASH_WRITABLE;
+ *IXP4XX_EXP_CS1 = *IXP4XX_EXP_CS0;
+
+ platform_add_devices(pronghorn_devices, ARRAY_SIZE(pronghorn_devices));
+
+ if (machine_is_pronghorn()) {
+ pronghorn_pata_resources[0].start = IXP4XX_EXP_BUS_BASE(2);
+ pronghorn_pata_resources[0].end = IXP4XX_EXP_BUS_END(2);
+
+ pronghorn_pata_resources[1].start = IXP4XX_EXP_BUS_BASE(3);
+ pronghorn_pata_resources[1].end = IXP4XX_EXP_BUS_END(3);
+
+ pronghorn_pata_data.cs0_cfg = IXP4XX_EXP_CS2;
+ pronghorn_pata_data.cs1_cfg = IXP4XX_EXP_CS3;
+ } else {
+ pronghorn_pata_resources[0].start = IXP4XX_EXP_BUS_BASE(3);
+ pronghorn_pata_resources[0].end = IXP4XX_EXP_BUS_END(3);
+
+ pronghorn_pata_resources[1].start = IXP4XX_EXP_BUS_BASE(4);
+ pronghorn_pata_resources[1].end = IXP4XX_EXP_BUS_END(4);
+
+ pronghorn_pata_data.cs0_cfg = IXP4XX_EXP_CS3;
+ pronghorn_pata_data.cs1_cfg = IXP4XX_EXP_CS4;
+
+ platform_device_register(&pronghorn_i2c_gpio);
+ }
+
+ platform_device_register(&pronghorn_pata);
+}
+
+MACHINE_START(PRONGHORN, "ADI Engineering Pronghorn")
+ /* Maintainer: Imre Kaloz <kaloz@openwrt.org> */
+ .map_io = ixp4xx_map_io,
+ .init_irq = ixp4xx_init_irq,
+ .timer = &ixp4xx_timer,
+ .boot_params = 0x0100,
+ .init_machine = pronghorn_init,
+MACHINE_END
+
+MACHINE_START(PRONGHORNMETRO, "ADI Engineering Pronghorn Metro")
+ /* Maintainer: Imre Kaloz <kaloz@openwrt.org> */
+ .map_io = ixp4xx_map_io,
+ .init_irq = ixp4xx_init_irq,
+ .timer = &ixp4xx_timer,
+ .boot_params = 0x0100,
+ .init_machine = pronghorn_init,
+MACHINE_END
--- a/arch/arm/mach-ixp4xx/include/mach/uncompress.h
+++ b/arch/arm/mach-ixp4xx/include/mach/uncompress.h
@@ -41,7 +41,8 @@ static __inline__ void __arch_decomp_set
* Some boards are using UART2 as console
*/
if (machine_is_adi_coyote() || machine_is_gtwx5715() ||
- machine_is_gateway7001() || machine_is_wg302v2())
+ machine_is_gateway7001() || machine_is_wg302v2() ||
+ machine_is_pronghorn() || machine_is_pronghorn_metro())
uart_base = (volatile u32*) IXP4XX_UART2_BASE_PHYS;
else
uart_base = (volatile u32*) IXP4XX_UART1_BASE_PHYS;
Reference in New Issue View Git Blame Copy Permalink