wifipineapple-openwrt/target/linux/ixp4xx/patches-2.6.34/191-cambria_optional_uart.p...

218 lines
6.7 KiB
Diff

--- a/arch/arm/mach-ixp4xx/cambria-setup.c
+++ b/arch/arm/mach-ixp4xx/cambria-setup.c
@@ -34,6 +34,7 @@
#include <asm/mach/arch.h>
#include <asm/mach/flash.h>
#include <asm/setup.h>
+#include <linux/irq.h>
struct cambria_board_info {
unsigned char *model;
@@ -127,6 +128,45 @@ static struct platform_device cambria_ua
.resource = &cambria_uart_resource,
};
+static struct resource cambria_optional_uart_resources[] = {
+ {
+ .start = 0x52000000,
+ .end = 0x52000fff,
+ .flags = IORESOURCE_MEM
+ },
+ {
+ .start = 0x53000000,
+ .end = 0x53000fff,
+ .flags = IORESOURCE_MEM
+ }
+};
+
+static struct plat_serial8250_port cambria_optional_uart_data[] = {
+ {
+ .flags = UPF_BOOT_AUTOCONF,
+ .iotype = UPIO_MEM_DELAY,
+ .regshift = 0,
+ .uartclk = 1843200,
+ .rw_delay = 2,
+ },
+ {
+ .flags = UPF_BOOT_AUTOCONF,
+ .iotype = UPIO_MEM_DELAY,
+ .regshift = 0,
+ .uartclk = 1843200,
+ .rw_delay = 2,
+ },
+ { },
+};
+
+static struct platform_device cambria_optional_uart = {
+ .name = "serial8250",
+ .id = PLAT8250_DEV_PLATFORM1,
+ .dev.platform_data = cambria_optional_uart_data,
+ .num_resources = 2,
+ .resource = cambria_optional_uart_resources,
+};
+
static struct resource cambria_pata_resources[] = {
{
.flags = IORESOURCE_MEM
@@ -283,6 +323,19 @@ static void __init cambria_gw23xx_setup(
static void __init cambria_gw2350_setup(void)
{
+ *IXP4XX_EXP_CS2 = 0xBFFF3C43;
+ set_irq_type(IRQ_IXP4XX_GPIO3, IRQ_TYPE_EDGE_RISING);
+ cambria_optional_uart_data[0].mapbase = 0x52FF0000;
+ cambria_optional_uart_data[0].membase = (void __iomem *)ioremap(0x52FF0000, 0x0fff);
+ cambria_optional_uart_data[0].irq = IRQ_IXP4XX_GPIO3;
+
+ *IXP4XX_EXP_CS3 = 0xBFFF3C43;
+ set_irq_type(IRQ_IXP4XX_GPIO4, IRQ_TYPE_EDGE_RISING);
+ cambria_optional_uart_data[1].mapbase = 0x53FF0000;
+ cambria_optional_uart_data[1].membase = (void __iomem *)ioremap(0x53FF0000, 0x0fff);
+ cambria_optional_uart_data[1].irq = IRQ_IXP4XX_GPIO4;
+
+ platform_device_register(&cambria_optional_uart);
platform_device_register(&cambria_npec_device);
platform_device_register(&cambria_npea_device);
@@ -294,6 +347,19 @@ static void __init cambria_gw2350_setup(
static void __init cambria_gw2358_setup(void)
{
+ *IXP4XX_EXP_CS3 = 0xBFFF3C43;
+ set_irq_type(IRQ_IXP4XX_GPIO3, IRQ_TYPE_EDGE_RISING);
+ cambria_optional_uart_data[0].mapbase = 0x53FC0000;
+ cambria_optional_uart_data[0].membase = (void __iomem *)ioremap(0x53FC0000, 0x0fff);
+ cambria_optional_uart_data[0].irq = IRQ_IXP4XX_GPIO3;
+
+ set_irq_type(IRQ_IXP4XX_GPIO4, IRQ_TYPE_EDGE_RISING);
+ cambria_optional_uart_data[1].mapbase = 0x53F80000;
+ cambria_optional_uart_data[1].membase = (void __iomem *)ioremap(0x53F80000, 0x0fff);
+ cambria_optional_uart_data[1].irq = IRQ_IXP4XX_GPIO4;
+
+ platform_device_register(&cambria_optional_uart);
+
platform_device_register(&cambria_npec_device);
platform_device_register(&cambria_npea_device);
--- a/include/linux/serial_8250.h
+++ b/include/linux/serial_8250.h
@@ -27,6 +27,7 @@ struct plat_serial8250_port {
void *private_data;
unsigned char regshift; /* register shift */
unsigned char iotype; /* UPIO_* */
+ unsigned int rw_delay; /* udelay for slower busses IXP4XX Expansion Bus */
unsigned char hub6;
upf_t flags; /* UPF_* flags */
unsigned int type; /* If UPF_FIXED_TYPE */
--- a/include/linux/serial_core.h
+++ b/include/linux/serial_core.h
@@ -288,6 +288,7 @@ struct uart_port {
#define UPIO_TSI (5) /* Tsi108/109 type IO */
#define UPIO_DWAPB (6) /* DesignWare APB UART */
#define UPIO_RM9000 (7) /* RM9000 type IO */
+#define UPIO_MEM_DELAY (8)
unsigned int read_status_mask; /* driver specific */
unsigned int ignore_status_mask; /* driver specific */
@@ -330,6 +331,7 @@ struct uart_port {
unsigned int mctrl; /* current modem ctrl settings */
unsigned int timeout; /* character-based timeout */
+ unsigned int rw_delay; /* udelay for slow busses, IXP4XX Expansion Bus */
unsigned int type; /* port type */
const struct uart_ops *ops;
unsigned int custom_divisor;
--- a/drivers/serial/8250.c
+++ b/drivers/serial/8250.c
@@ -410,6 +410,20 @@ static void mem_serial_out(struct uart_p
writeb(value, p->membase + offset);
}
+static unsigned int memdelay_serial_in(struct uart_port *p, int offset)
+{
+ struct uart_8250_port *up = (struct uart_8250_port *)p;
+ udelay(up->port.rw_delay);
+ return mem_serial_in(p, offset);
+}
+
+static void memdelay_serial_out(struct uart_port *p, int offset, int value)
+{
+ struct uart_8250_port *up = (struct uart_8250_port *)p;
+ udelay(up->port.rw_delay);
+ mem_serial_out(p, offset, value);
+}
+
static void mem32_serial_out(struct uart_port *p, int offset, int value)
{
offset = map_8250_out_reg(p, offset) << p->regshift;
@@ -503,6 +517,11 @@ static void set_io_from_upio(struct uart
p->serial_out = mem32_serial_out;
break;
+ case UPIO_MEM_DELAY:
+ p->serial_in = memdelay_serial_in;
+ p->serial_out = memdelay_serial_out;
+ break;
+
#ifdef CONFIG_SERIAL_8250_AU1X00
case UPIO_AU:
p->serial_in = au_serial_in;
@@ -535,6 +554,7 @@ serial_out_sync(struct uart_8250_port *u
switch (p->iotype) {
case UPIO_MEM:
case UPIO_MEM32:
+ case UPIO_MEM_DELAY:
#ifdef CONFIG_SERIAL_8250_AU1X00
case UPIO_AU:
#endif
@@ -2460,6 +2480,7 @@ static int serial8250_request_std_resour
case UPIO_MEM32:
case UPIO_MEM:
case UPIO_DWAPB:
+ case UPIO_MEM_DELAY:
if (!up->port.mapbase)
break;
@@ -2497,6 +2518,7 @@ static void serial8250_release_std_resou
case UPIO_MEM32:
case UPIO_MEM:
case UPIO_DWAPB:
+ case UPIO_MEM_DELAY:
if (!up->port.mapbase)
break;
@@ -2995,6 +3017,7 @@ static int __devinit serial8250_probe(st
port.serial_in = p->serial_in;
port.serial_out = p->serial_out;
port.dev = &dev->dev;
+ port.rw_delay = p->rw_delay;
port.irqflags |= irqflag;
ret = serial8250_register_port(&port);
if (ret < 0) {
@@ -3144,6 +3167,7 @@ int serial8250_register_port(struct uart
uart->port.iotype = port->iotype;
uart->port.flags = port->flags | UPF_BOOT_AUTOCONF;
uart->port.mapbase = port->mapbase;
+ uart->port.rw_delay = port->rw_delay;
uart->port.private_data = port->private_data;
if (port->dev)
uart->port.dev = port->dev;
--- a/drivers/serial/serial_core.c
+++ b/drivers/serial/serial_core.c
@@ -2144,6 +2144,7 @@ uart_report_port(struct uart_driver *drv
snprintf(address, sizeof(address),
"I/O 0x%lx offset 0x%x", port->iobase, port->hub6);
break;
+ case UPIO_MEM_DELAY:
case UPIO_MEM:
case UPIO_MEM32:
case UPIO_AU:
@@ -2557,6 +2558,7 @@ int uart_match_port(struct uart_port *po
case UPIO_HUB6:
return (port1->iobase == port2->iobase) &&
(port1->hub6 == port2->hub6);
+ case UPIO_MEM_DELAY:
case UPIO_MEM:
case UPIO_MEM32:
case UPIO_AU: