wifipineapple-openwrt/target/linux/generic-2.6/patches-2.6.23/210-mac80211_include_wirele...

807 lines
25 KiB
Diff

--- a/include/linux/ieee80211.h
+++ b/include/linux/ieee80211.h
@@ -106,6 +106,75 @@
} __attribute__ ((packed));
+struct ieee80211_ht_capability {
+ __le16 capabilities_info;
+ u8 mac_ht_params_info;
+ u8 supported_mcs_set[16];
+ __le16 extended_ht_capability_info;
+ __le32 tx_BF_capability_info;
+ u8 antenna_selection_info;
+}__attribute__ ((packed));
+
+struct ieee80211_ht_additional_info {
+ u8 control_chan;
+ u8 ht_param;
+ __le16 operation_mode;
+ __le16 stbc_param;
+ u8 basic_set[16];
+}__attribute__ ((packed));
+
+
+#define IEEE80211_TSINFO_TYPE(a) ((a.byte1 & 0x01) >> 0)
+#define IEEE80211_TSINFO_TSID(a) ((a.byte1 & 0x1E) >> 1)
+#define IEEE80211_TSINFO_DIR(a) ((a.byte1 & 0x60) >> 5)
+#define IEEE80211_TSINFO_POLICY(a) ((a.byte1 & 0x80) >> 7 + \
+ (a.byte2 & 0x01) << 1)
+#define IEEE80211_TSINFO_AGG(a) ((a.byte2 & 0x02) >> 1)
+#define IEEE80211_TSINFO_APSD(a) ((a.byte2 & 0x04) >> 2)
+#define IEEE80211_TSINFO_UP(a) ((a.byte2 & 0x38) >> 3)
+#define IEEE80211_TSINFO_ACK(a) ((a.byte2 & 0xC0) >> 6)
+#define IEEE80211_TSINFO_SCHEDULE(a) ((a.byte3 & 0x01) >> 0)
+
+#define IEEE80211_SET_TSINFO_TYPE(i, d) (i.byte1 |= (d << 0) & 0x01)
+#define IEEE80211_SET_TSINFO_TSID(i, d) (i.byte1 |= (d << 1) & 0x1E)
+#define IEEE80211_SET_TSINFO_DIR(i, d) (i.byte1 |= (d << 5) & 0x60)
+#define IEEE80211_SET_TSINFO_POLICY(i, d) \
+do { \
+ i.byte1 |= (d & 0x01) << 7; \
+ i.byte2 |= (d & 0x02) >> 1; \
+} while(0)
+#define IEEE80211_SET_TSINFO_AGG(i, d) (i.byte2 |= (d << 1) & 0x02)
+#define IEEE80211_SET_TSINFO_APSD(i, d) (i.byte2 |= (d << 2) & 0x04)
+#define IEEE80211_SET_TSINFO_UP(i, d) (i.byte2 |= (d << 3) & 0x38)
+#define IEEE80211_SET_TSINFO_ACK(i, d) (i.byte2 |= (d << 6) & 0xC0)
+#define IEEE80211_SET_TSINFO_SCHEDULE(i, d) (i.byte3 |= (d << 0) & 0x01)
+
+struct ieee80211_ts_info {
+ u8 byte1;
+ u8 byte2;
+ u8 byte3;
+} __attribute__ ((packed));
+
+struct ieee80211_elem_tspec {
+ struct ieee80211_ts_info ts_info;
+ __le16 nominal_msdu_size;
+ __le16 max_msdu_size;
+ __le32 min_service_interval;
+ __le32 max_service_interval;
+ __le32 inactivity_interval;
+ __le32 suspension_interval;
+ __le32 service_start_time;
+ __le32 min_data_rate;
+ __le32 mean_data_rate;
+ __le32 peak_data_rate;
+ __le32 burst_size;
+ __le32 delay_bound;
+ __le32 min_phy_rate;
+ __le16 surplus_band_allow;
+ __le16 medium_time;
+} __attribute__ ((packed));
+
+
struct ieee80211_mgmt {
__le16 frame_control;
__le16 duration;
@@ -173,9 +242,51 @@
struct {
u8 action_code;
u8 dialog_token;
+ u8 variable[0];
+ } __attribute__ ((packed)) addts_req;
+ struct {
+ u8 action_code;
+ u8 dialog_token;
+ __le16 status_code;
+ u8 variable[0];
+ } __attribute__ ((packed)) addts_resp;
+ struct {
+ u8 action_code;
+ struct ieee80211_ts_info ts_info;
+ __le16 reason_code;
+ } __attribute__ ((packed)) delts;
+ struct {
+ u8 action_code;
+ u8 dialog_token;
u8 status_code;
u8 variable[0];
} __attribute__ ((packed)) wme_action;
+ struct {
+ u8 action_code;
+ u8 dest[6];
+ u8 src[6];
+ __le16 capab_info;
+ __le16 timeout;
+ /* Followed by Supported Rates and
+ * Extended Supported Rates */
+ u8 variable[0];
+ } __attribute__ ((packed)) dls_req;
+ struct {
+ u8 action_code;
+ __le16 status_code;
+ u8 dest[6];
+ u8 src[6];
+ /* Followed by Capability Information,
+ * Supported Rates and Extended
+ * Supported Rates */
+ u8 variable[0];
+ } __attribute__ ((packed)) dls_resp;
+ struct {
+ u8 action_code;
+ u8 dest[6];
+ u8 src[6];
+ __le16 reason_code;
+ } __attribute__ ((packed)) dls_teardown;
struct{
u8 action_code;
u8 element_id;
@@ -184,6 +295,25 @@
u8 new_chan;
u8 switch_count;
} __attribute__((packed)) chan_switch;
+ struct{
+ u8 action_code;
+ u8 dialog_token;
+ __le16 capab;
+ __le16 timeout;
+ __le16 start_seq_num;
+ } __attribute__((packed)) addba_req;
+ struct{
+ u8 action_code;
+ u8 dialog_token;
+ __le16 status;
+ __le16 capab;
+ __le16 timeout;
+ } __attribute__((packed)) addba_resp;
+ struct{
+ u8 action_code;
+ __le16 params;
+ __le16 reason_code;
+ }__attribute__((packed)) delba;
} u;
} __attribute__ ((packed)) action;
} u;
@@ -270,6 +400,18 @@
WLAN_STATUS_UNSUPP_RSN_VERSION = 44,
WLAN_STATUS_INVALID_RSN_IE_CAP = 45,
WLAN_STATUS_CIPHER_SUITE_REJECTED = 46,
+ /* 802.11e */
+ WLAN_STATUS_UNSPECIFIED_QOS = 32,
+ WLAN_STATUS_ASSOC_DENIED_NOBANDWIDTH = 33,
+ WLAN_STATUS_ASSOC_DENIED_LOWACK = 34,
+ WLAN_STATUS_ASSOC_DENIED_UNSUPP_QOS = 35,
+ WLAN_STATUS_REQUEST_DECLINED = 37,
+ WLAN_STATUS_INVALID_QOS_PARAM = 38,
+ WLAN_STATUS_CHANGE_TSPEC = 39,
+ WLAN_STATUS_WAIT_TS_DELAY = 47,
+ WLAN_STATUS_NO_DIRECT_LINK = 48,
+ WLAN_STATUS_STA_NOT_PRESENT = 49,
+ WLAN_STATUS_STA_NOT_QSTA = 50,
};
@@ -300,9 +442,50 @@
WLAN_REASON_INVALID_RSN_IE_CAP = 22,
WLAN_REASON_IEEE8021X_FAILED = 23,
WLAN_REASON_CIPHER_SUITE_REJECTED = 24,
+ /* 802.11e */
+ WLAN_REASON_DISASSOC_UNSPECIFIED_QOS = 32,
+ WLAN_REASON_DISASSOC_QAP_NO_BANDWIDTH = 33,
+ WLAN_REASON_DISASSOC_LOW_ACK = 34,
+ WLAN_REASON_DISASSOC_QAP_EXCEED_TXOP = 35,
+ WLAN_REASON_QSTA_LEAVE_QBSS = 36,
+ WLAN_REASON_QSTA_NOT_USE = 37,
+ WLAN_REASON_QSTA_REQUIRE_SETUP = 38,
+ WLAN_REASON_QSTA_TIMEOUT = 39,
+ WLAN_REASON_QSTA_CIPHER_NOT_SUPP = 45,
};
+/* Category Code */
+enum ieee80211_category {
+ WLAN_CATEGORY_SPECTRUM_MGMT = 0,
+ WLAN_CATEGORY_QOS = 1,
+ WLAN_CATEGORY_DLS = 2,
+ WLAN_CATEGORY_BACK = 3,
+ WLAN_CATEGORY_WMM = 17,
+};
+
+/* QoS Action Code */
+enum ieee80211_qos_actioncode {
+ WLAN_ACTION_QOS_ADDTS_REQ = 0,
+ WLAN_ACTION_QOS_ADDTS_RESP = 1,
+ WLAN_ACTION_QOS_DELTS = 2,
+ WLAN_ACTION_QOS_SCHEDULE = 3,
+};
+
+/* DLS Action Code */
+enum ieee80211_dls_actioncode {
+ WLAN_ACTION_DLS_REQ = 0,
+ WLAN_ACTION_DLS_RESP = 1,
+ WLAN_ACTION_DLS_TEARDOWN = 2,
+};
+
+/* BACK Action Code */
+enum ieee80211_back_actioncode {
+ WLAN_ACTION_ADDBA_REQ = 0,
+ WLAN_ACTION_ADDBA_RESP = 1,
+ WLAN_ACTION_DELBA = 2,
+};
+
/* Information Element IDs */
enum ieee80211_eid {
WLAN_EID_SSID = 0,
@@ -318,6 +501,15 @@
WLAN_EID_HP_PARAMS = 8,
WLAN_EID_HP_TABLE = 9,
WLAN_EID_REQUEST = 10,
+ /* 802.11e */
+ WLAN_EID_QBSS_LOAD = 11,
+ WLAN_EID_EDCA_PARAM_SET = 12,
+ WLAN_EID_TSPEC = 13,
+ WLAN_EID_TCLAS = 14,
+ WLAN_EID_SCHEDULE = 15,
+ WLAN_EID_TS_DELAY = 43,
+ WLAN_EID_TCLAS_PROCESSING = 44,
+ WLAN_EID_QOS_CAPA = 46,
/* 802.11h */
WLAN_EID_PWR_CONSTRAINT = 32,
WLAN_EID_PWR_CAPABILITY = 33,
@@ -332,6 +524,9 @@
/* 802.11g */
WLAN_EID_ERP_INFO = 42,
WLAN_EID_EXT_SUPP_RATES = 50,
+ /* 802.11n */
+ WLAN_EID_HT_CAPABILITY = 45,
+ WLAN_EID_HT_EXTRA_INFO = 61,
/* 802.11i */
WLAN_EID_RSN = 48,
WLAN_EID_WPA = 221,
@@ -340,6 +535,9 @@
WLAN_EID_QOS_PARAMETER = 222
};
+/* 80211n */
+#define IEEE80211_QOS_CONTROL_A_MSDU_PRESENT 0x0080
+
/* cipher suite selectors */
#define WLAN_CIPHER_SUITE_USE_GROUP 0x000FAC00
#define WLAN_CIPHER_SUITE_WEP40 0x000FAC01
@@ -350,4 +548,37 @@
#define WLAN_MAX_KEY_LEN 32
+enum ieee80211_tsinfo_direction {
+ WLAN_TSINFO_UPLINK = 0,
+ WLAN_TSINFO_DOWNLINK = 1,
+ WLAN_TSINFO_DIRECTLINK = 2,
+ WLAN_TSINFO_BIDIRECTIONAL = 3,
+};
+
+enum ieee80211_tsinfo_access {
+ WLAN_TSINFO_EDCA = 1,
+ WLAN_TSINFO_HCCA = 2,
+ WLAN_TSINFO_HEMM = 3,
+};
+
+enum ieee80211_tsinfo_psb {
+ WLAN_TSINFO_PSB_LEGACY = 0,
+ WLAN_TSINFO_PSB_APSD = 1,
+};
+
+
+/* WI-FI Alliance OUI Type and Subtype */
+enum wifi_oui_type {
+ WIFI_OUI_TYPE_WPA = 1,
+ WIFI_OUI_TYPE_WMM = 2,
+ WIFI_OUI_TYPE_WSC = 4,
+ WIFI_OUI_TYPE_PSD = 6,
+};
+
+enum wifi_oui_stype_wmm {
+ WIFI_OUI_STYPE_WMM_INFO = 0,
+ WIFI_OUI_STYPE_WMM_PARAM = 1,
+ WIFI_OUI_STYPE_WMM_TSPEC = 2,
+};
+
#endif /* IEEE80211_H */
--- a/include/linux/nl80211.h
+++ b/include/linux/nl80211.h
@@ -7,6 +7,217 @@
*/
/**
+ * enum nl80211_commands - supported nl80211 commands
+ * @NL80211_CMD_UNSPEC: unspecified command to catch errors
+ * @NL80211_CMD_RENAME_WIPHY: rename a wiphy, needs
+ * %NL80211_ATTR_WIPHY and %NL80211_ATTR_WIPHY_NAME
+ * @NL80211_CMD_WIPHY_NEWNAME: rename notification
+ * @NL80211_CMD_GET_CMDLIST: TO BE DEFINED PROPERLY. currently the code makes
+ * it depend on the wiphy only but it really should depend on the
+ * interface type too....
+ * @NL80211_CMD_NEW_CMDLIST: command list result
+ * @NL80211_CMD_ADD_VIRTUAL_INTERFACE: create a virtual interface for the
+ * wiphy identified by an %NL80211_ATTR_WIPHY attribute with the given
+ * %NL80211_ATTR_IFTYPE and %NL80211_ATTR_IFNAME.
+ * @NL80211_CMD_DEL_VIRTUAL_INTERFACE: destroy a virtual interface identified
+ * by %NL80211_ATTR_IFINDEX.
+ * @NL80211_CMD_CHANGE_VIRTUAL_INTERFACE: change type of virtual interface to
+ * the type given by %NL80211_ATTR_IFTYPE, the interface is identified by
+ * %NL80211_ATTR_IFINDEX.
+ * @NL80211_CMD_GET_WIPHYS: request a list of all wiphys present in the system
+ * @NL80211_CMD_NEW_WIPHYS: returned list of all wiphys
+ * @NL80211_CMD_GET_INTERFACES: request a list of all interfaces belonging to
+ * the wiphy identified by %NL80211_ATTR_WIPHY
+ * @NL80211_CMD_NEW_INTERFACES: result for %NL80211_CMD_GET_INTERFACES
+ * @NL80211_CMD_INITIATE_SCAN: initiate a scan with the passed parameters. THe
+ * parameters may contain %NL80211_ATTR_FLAG_SCAN_ACTIVE,
+ * %NL80211_ATTR_PHYMODE and a list of channels in an
+ * %NL80211_ATTR_CHANNEL_LIST attribute (an array of nested attributes)
+ * containing %NL80211_ATTR_CHANNEL, %NL80211_ATTR_PHYMODE, and possibly
+ * %NL80211_ATTR_FLAG_SCAN_ACTIVE. The outer %NL80211_ATTR_FLAG_SCAN_ACTIVE
+ * is ignored when a channel list is present.
+ * @NL80211_CMD_SCAN_RESULT: scan result, contains an array in
+ * %NL80211_ATTR_BSS_LIST.
+ * @NL80211_CMD_ASSOCIATE: associate with the given parameters
+ * (%NL80211_ATTR_SSID is mandatory, %NL80211_ATTR_TIMEOUT_TU,
+ * %NL80211_ATTR_BSSID, %NL80211_ATTR_CHANNEL, %NL80211_ATTR_PHYMODE,
+ * and %NL80211_ATTR_IE may be given)
+ * @NL80211_CMD_ADD_KEY: add a key with given %NL80211_ATTR_KEY_DATA,
+ * %NL80211_ATTR_KEY_ID, %NL80211_ATTR_KEY_TYPE, %NL80211_ATTR_MAC and
+ * %NL80211_ATTR_KEY_CIPHER attributes.
+ * @NL80211_CMD_DEL_KEY: delete a key identified by %NL80211_ATTR_KEY_ID,
+ * %NL80211_ATTR_KEY_TYPE and %NL80211_ATTR_MAC or all keys.
+ * @__NL80211_CMD_AFTER_LAST: internal use
+ */
+enum nl80211_commands {
+/* don't change the order or add anything inbetween, this is ABI! */
+ NL80211_CMD_UNSPEC,
+ /* %input: wiphy, wiphy_name */
+ NL80211_CMD_RENAME_WIPHY,
+ NL80211_CMD_WIPHY_NEWNAME,
+ /* %input: wiphy|ifindex */
+ NL80211_CMD_GET_CMDLIST,
+ NL80211_CMD_NEW_CMDLIST,
+ /* %input: wiphy, ifname, {iftype} */
+ NL80211_CMD_ADD_VIRTUAL_INTERFACE,
+ /* %input: wiphy, ifindex */
+ NL80211_CMD_DEL_VIRTUAL_INTERFACE,
+ /* %input: ifindex, iftype */
+ NL80211_CMD_CHANGE_VIRTUAL_INTERFACE,
+ /* %input: */
+ NL80211_CMD_GET_WIPHYS,
+ NL80211_CMD_NEW_WIPHYS,
+ /* %input: wiphy */
+ NL80211_CMD_GET_INTERFACES,
+ NL80211_CMD_NEW_INTERFACES,
+ NL80211_CMD_INITIATE_SCAN,
+ NL80211_CMD_SCAN_RESULT,
+ NL80211_CMD_GET_ASSOCIATION,
+ NL80211_CMD_ASSOCIATION_CHANGED,
+ NL80211_CMD_ASSOCIATE,
+ NL80211_CMD_DISASSOCIATE,
+ NL80211_CMD_DEAUTH,
+ NL80211_CMD_GET_AUTH_LIST,
+ NL80211_CMD_NEW_AUTH_LIST,
+ NL80211_CMD_AUTHENTICATION_CHANGED,
+ NL80211_CMD_AP_SET_BEACON,
+ NL80211_CMD_AP_ADD_STA,
+ NL80211_CMD_AP_UPDATE_STA,
+ NL80211_CMD_AP_GET_STA_INFO,
+ NL80211_CMD_AP_SET_RATESETS,
+ NL80211_CMD_ADD_KEY,
+ NL80211_CMD_DEL_KEY,
+
+ /* add commands here */
+
+ /* used to define NL80211_CMD_MAX below */
+ __NL80211_CMD_AFTER_LAST
+};
+#define NL80211_CMD_MAX (__NL80211_CMD_AFTER_LAST - 1)
+
+
+/**
+ * enum nl80211_attrs - nl80211 netlink attributes
+ * @NL80211_ATTR_UNSPEC: unspecified attribute to catch errors
+ * @NL80211_ATTR_IFINDEX: network interface index of the device to operate on
+ * @NL80211_ATTR_IFNAME: network interface name
+ * @NL80211_ATTR_WIPHY: index of wiphy to operate on, cf.
+ * /sys/class/ieee80211/<phyname>/index
+ * @NL80211_ATTR_WIPHY_NAME: wiphy name (used for renaming)
+ * @NL80211_ATTR_CMDS: list of u8's identifying commands a device supports
+ * @NL80211_ATTR_IFTYPE: type of virtual interface, see &enum nl80211_iftype
+ * @NL80211_ATTR_INTERFACE_LIST: interface array, nested netlink attribute
+ * @NL80211_ATTR_WIPHY_LIST: wiphy array, nested netlink attribute
+ * @NL80211_ATTR_BSSID: BSSID (must be 6 bytes)
+ * @NL80211_ATTR_SSID: SSID (1-32 bytes)
+ * @NL80211_ATTR_CHANNEL: channel number
+ * @NL80211_ATTR_PHYMODE: PHY mode, see &enum nl80211_phymode
+ * @NL80211_ATTR_CHANNEL_LIST: netlink nested attribute array containing scan
+ * parameters for channels
+ * @NL80211_ATTR_BSS_LIST: nested attribute containing an array
+ * @NL80211_ATTR_BSSTYPE: BSS type, see &enum nl80211_bsstype
+ * @NL80211_ATTR_BEACON_PERIOD: beacon period
+ * @NL80211_ATTR_DTIM_PERIOD: DTIM period
+ * @NL80211_ATTR_TIMESTAMP: 64-bit timestamp of received beacon/probe response
+ * @NL80211_ATTR_IE: information element(s), maximum length %NL80211_MAX_IE_LEN
+ * @NL80211_ATTR_AUTH_ALGORITHM: authentication algorithm
+ * @NL80211_ATTR_TIMEOUT_TU: timeout in TU (TO BE USED)
+ * @NL80211_ATTR_REASON_CODE: 802.11 reason code
+ * @NL80211_ATTR_ASSOCIATION_ID: association ID (u16, 1-2007)
+ * @NL80211_ATTR_DEAUTHENTICATED: TO BE USED
+ * @NL80211_ATTR_RX_SENSITIVITY: receiver sensitivity in dBm
+ * @NL80211_ATTR_TRANSMIT_POWER: transmit power in mW
+ * @NL80211_ATTR_FRAG_THRESHOLD: fragmentation threshold (bytes)
+ * @NL80211_ATTR_FLAG_SCAN_ACTIVE: netlink flag indiciating active scan
+ * @NL80211_ATTR_KEY_DATA: temporal key data
+ * @NL80211_ATTR_KEY_ID: key ID (u8, 0-3)
+ * @NL80211_ATTR_KEY_TYPE: key type (see &enum nl80211_keytype)
+ * @NL80211_ATTR_MAC: MAC address
+ * @NL80211_ATTR_KEY_CIPHER: key cipher suite (u32)
+ * @__NL80211_ATTR_AFTER_LAST: internal use
+ */
+enum nl80211_attrs {
+/* don't change the order or add anything inbetween, this is ABI! */
+ NL80211_ATTR_UNSPEC,
+ /* %type: u32 */
+ NL80211_ATTR_IFINDEX,
+ /* %type: nulstring */
+ NL80211_ATTR_IFNAME,
+ /* %type: u32 */
+ NL80211_ATTR_WIPHY,
+ /* %type: nulstring */
+ NL80211_ATTR_WIPHY_NAME,
+ NL80211_ATTR_CMDS,
+ /* %type: u32 */
+ NL80211_ATTR_IFTYPE,
+ NL80211_ATTR_INTERFACE_LIST,
+ NL80211_ATTR_WIPHY_LIST,
+ NL80211_ATTR_BSSID,
+ NL80211_ATTR_SSID,
+ NL80211_ATTR_CHANNEL,
+ NL80211_ATTR_PHYMODE,
+ NL80211_ATTR_CHANNEL_LIST,
+ NL80211_ATTR_BSS_LIST,
+ NL80211_ATTR_BSSTYPE,
+ NL80211_ATTR_BEACON_PERIOD,
+ NL80211_ATTR_DTIM_PERIOD,
+ NL80211_ATTR_TIMESTAMP,
+ NL80211_ATTR_IE,
+ NL80211_ATTR_AUTH_ALGORITHM,
+ NL80211_ATTR_TIMEOUT_TU,
+ NL80211_ATTR_REASON_CODE,
+ NL80211_ATTR_ASSOCIATION_ID,
+ NL80211_ATTR_DEAUTHENTICATED,
+ NL80211_ATTR_RX_SENSITIVITY,
+ NL80211_ATTR_TRANSMIT_POWER,
+ NL80211_ATTR_FRAG_THRESHOLD,
+ NL80211_ATTR_FLAG_SCAN_ACTIVE,
+
+ NL80211_ATTR_KEY_DATA,
+ NL80211_ATTR_KEY_ID,
+ NL80211_ATTR_KEY_TYPE,
+ NL80211_ATTR_MAC,
+ NL80211_ATTR_KEY_CIPHER,
+
+ NL80211_ATTR_BEACON_HEAD,
+ NL80211_ATTR_BEACON_TAIL,
+
+ /* add attributes here, update the policy in nl80211.c */
+
+ /* used to define NL80211_ATTR_MAX below */
+ __NL80211_ATTR_AFTER_LAST,
+};
+#define NL80211_ATTR_MAX (__NL80211_ATTR_AFTER_LAST - 1)
+
+/**
+ * enum nl80211_multicast_groups - multicast groups for nl80211
+ * @NL80211_GROUP_CONFIG: members of this group are notified of
+ * configuration changes
+ */
+enum nl80211_multicast_groups {
+ /* be notified of configuration changes like wiphy renames */
+ NL80211_GROUP_CONFIG,
+
+ /* add groups here */
+
+ /* keep last */
+ __NL80211_GROUP_AFTER_LAST
+};
+#define NL80211_GROUP_MAX (__NL80211_GROUP_AFTER_LAST - 1)
+
+/*
+ * maximum length of IE(s) passed in an NL80211_ATTR_IE.
+ * this is an arbitrary limit, 774 means three full-length
+ * IEs would fit... increase if necessary */
+#define NL80211_MAX_IE_LEN 774
+
+/*
+ * maximum number of items in an ATTR_CHANNEL_LIST,
+ * just to avoid too large allocations
+ */
+#define NL80211_MAX_CHANNEL_LIST_ITEM 200
+
+/**
* enum nl80211_iftype - (virtual) interface types
* @NL80211_IFTYPE_UNSPECIFIED: unspecified type, driver decides
* @NL80211_IFTYPE_ADHOC: independent BSS member
@@ -35,4 +246,56 @@
};
#define NL80211_IFTYPE_MAX (__NL80211_IFTYPE_AFTER_LAST - 1)
+/**
+ * enum nl80211_phymode - PHY modes
+ * @NL80211_PHYMODE_A: 5 GHz PHY
+ * @NL80211_PHYMODE_B: 2.4 GHz PHY (B mode)
+ * @NL80211_PHYMODE_G: 2.4 GHz PHY (G, compatible with B)
+ * @__NL80211_PHYMODE_AFTER_LAST: internal use
+ *
+ * These values are used for %NL80211_ATTR_PHYMODE.
+ */
+enum nl80211_phymode {
+ NL80211_PHYMODE_A,
+ NL80211_PHYMODE_B,
+ NL80211_PHYMODE_G,
+
+ /* keep last */
+ __NL80211_PHYMODE_AFTER_LAST
+};
+#define NL80211_PHYMODE_MAX (__NL80211_PHYMODE_AFTER_LAST - 1)
+
+/**
+ * enum nl80211_bsstype - BSS types
+ * @NL80211_BSSTYPE_INFRASTRUCTURE: infrastructure BSS
+ * @NL80211_BSSTYPE_INDEPENDENT: independent BSS (ad-hoc network)
+ * @__NL80211_BSSTYPE_AFTER_LAST: internal use
+ *
+ * These values are used for %NL80211_ATTR_BSSTYPE.
+ */
+enum nl80211_bsstype {
+ NL80211_BSSTYPE_INFRASTRUCTURE,
+ NL80211_BSSTYPE_INDEPENDENT,
+
+ /* keep last */
+ __NL80211_BSSTYPE_AFTER_LAST
+};
+#define NL80211_BSSTYPE_MAX (__NL80211_BSSTYPE_AFTER_LAST - 1)
+
+/**
+ * enum nl80211_keytype - key types
+ * @NL80211_KEYTYPE_GROUP: group key
+ * @NL80211_KEYTYPE_PAIRWISE: pairwise key
+ * @NL80211_KEYTYPE_PEER: peer key
+ */
+enum nl80211_keytype {
+ NL80211_KEYTYPE_GROUP,
+ NL80211_KEYTYPE_PAIRWISE,
+ NL80211_KEYTYPE_PEER,
+
+ /* keep last */
+ __NL80211_KEYTYPE_AFTER_LAST
+};
+#define NL80211_KEYTYPE_MAX (__NL80211_KEYTYPE_AFTER_LAST - 1)
+
#endif /* __LINUX_NL80211_H */
--- a/include/net/cfg80211.h
+++ b/include/net/cfg80211.h
@@ -3,6 +3,7 @@
#include <linux/netlink.h>
#include <linux/skbuff.h>
+#include <linux/nl80211.h>
#include <net/genetlink.h>
/*
@@ -49,6 +50,69 @@
struct ieee80211_radiotap_iterator *iterator);
+/**
+ * struct scan_channel - describes a single channel to scan
+ * @phymode: PHY mode for this channel
+ * @channel: channel number (1-14, ...)
+ * @active: scan actively or passively on this channel
+ */
+struct scan_channel {
+ enum nl80211_phymode phymode;
+ u32 channel;
+ int active;
+};
+
+/**
+ * struct scan_params - describes scan parameters
+ * @n_channels: number of items in @channels array or -1 to indicate all
+ * channels should be scanned (in that case @channels will be %NULL)
+ * @active: when n_channels is -1 this determines active/passive scanning.
+ * @phymode: when n_channels is -1 this determines PHY mode to scan. It is
+ * not possible to scan different PHY modes in one request w/o giving
+ * a channel list.
+ * @channels: array containing @n_channels &struct scan_channel items
+ */
+struct scan_params {
+ int n_channels;
+ int active;
+ enum nl80211_phymode phymode;
+ struct scan_channel *channels;
+};
+
+/**
+ * struct association_params - describes association parameters
+ * @valid: this member contains flags which items are valid
+ * @bssid: the BSSID of the BSS to associate [%ASSOC_PARAMS_BSSID]
+ * @timeout: timeout (in TU) [%ASSOC_PARAMS_TIMEOUT]
+ * @ie: information element(s) to include in the association frames [%ASSOC_PARAMS_IE]
+ * @ie_len: length of the information element(s)
+ * @ssid: the SSID, always valid.
+ * @ssid_len: length of the SSID
+ */
+struct association_params {
+ u8 *bssid;
+ u32 timeout;
+ u8 *ie;
+ int ie_len;
+ u8 *ssid;
+ int ssid_len;
+
+ unsigned int valid;
+};
+#define ASSOC_PARAMS_TIMEOUT (1<<0)
+
+/**
+ * struct key_params - key information
+ */
+struct key_params {
+ u8 *key;
+ int key_len;
+ int key_id;
+ u32 key_type;
+ u8 *macaddress;
+ u32 cipher;
+};
+
/* from net/wireless.h */
struct wiphy;
@@ -68,11 +132,62 @@
* @add_virtual_intf: create a new virtual interface with the given name
*
* @del_virtual_intf: remove the virtual interface determined by ifindex.
+ *
+ * @change_virtual_intf: change type of virtual interface
+ *
+ * @associate: associate with given parameters
+ *
+ * @disassociate: disassociate from current AP
+ *
+ * @deauth: deauth from current AP
+ *
+ * @initiate_scan: scan with the given information (see &struct scan_params above)
+ *
+ * @get_association: get BSSID of the BSS that the device is currently
+ * associated to and return 1, or return 0 if not
+ * associated (or a negative error code)
+ * @get_auth_list: get list of BSSIDs of all BSSs the device has
+ * authenticated with, must call next_bssid for each,
+ * next_bssid returns non-zero on error, the given data
+ * is to be passed to that callback
+ * @add_key: add a key using &struct key_params
+ * @del_key: delete a key using info from &struct key_params
*/
struct cfg80211_ops {
int (*add_virtual_intf)(struct wiphy *wiphy, char *name,
- unsigned int type);
+ enum nl80211_iftype type);
int (*del_virtual_intf)(struct wiphy *wiphy, int ifindex);
+ int (*change_virtual_intf)(struct wiphy *wiphy, int ifindex,
+ enum nl80211_iftype type);
+
+ int (*associate)(struct wiphy *wiphy, struct net_device *dev,
+ struct association_params *params);
+ int (*disassociate)(struct wiphy *wiphy, struct net_device *dev);
+ int (*deauth)(struct wiphy *wiphy, struct net_device *dev);
+
+
+ int (*initiate_scan)(struct wiphy *wiphy, struct net_device *dev,
+ struct scan_params *params);
+
+
+ int (*get_association)(struct wiphy *wiphy, struct net_device *dev,
+ u8 *bssid);
+
+ int (*get_auth_list)(struct wiphy *wiphy, struct net_device *dev,
+ void *data,
+ int (*next_bssid)(void *data, u8 *bssid));
+
+ int (*add_key)(struct wiphy *wiphy, struct net_device *dev,
+ struct key_params *params);
+ int (*del_key)(struct wiphy *wiphy, struct net_device *dev,
+ struct key_params *params);
};
+
+/* helper functions specific to nl80211 */
+extern void *nl80211hdr_put(struct sk_buff *skb, u32 pid,
+ u32 seq, int flags, u8 cmd);
+extern void *nl80211msg_new(struct sk_buff **skb, u32 pid,
+ u32 seq, int flags, u8 cmd);
+
#endif /* __NET_CFG80211_H */
--- a/include/net/iw_handler.h
+++ b/include/net/iw_handler.h
@@ -431,7 +431,13 @@
* Those may be called only within the kernel.
*/
-/* functions that may be called by driver modules */
+/* First : function strictly used inside the kernel */
+
+/* Handle /proc/net/wireless, called in net/code/dev.c */
+extern int dev_get_wireless_info(char * buffer, char **start, off_t offset,
+ int length);
+
+/* Second : functions that may be called by driver modules */
/* Send a single event to user space */
extern void wireless_send_event(struct net_device * dev,
--- a/include/net/mac80211.h
+++ b/include/net/mac80211.h
@@ -300,7 +300,6 @@
/* Following five fields are used for IEEE 802.11H */
unsigned int radar_detect;
unsigned int spect_mgmt;
- /* All following fields are currently unused. */
unsigned int quiet_duration; /* duration of quiet period */
unsigned int quiet_offset; /* how far into the beacon is the quiet
* period */
@@ -521,6 +520,9 @@
* per-packet RC4 key with each TX frame when doing hwcrypto */
#define IEEE80211_HW_TKIP_REQ_PHASE2_KEY (1<<14)
+ /* The device capable of supporting 11n */
+#define IEEE80211_HW_SUPPORT_HT_MODE (1<<15)
+
u32 flags; /* hardware flags defined above */
/* Set to the size of a needed device specific skb headroom for TX skbs. */
@@ -649,8 +651,7 @@
* used if the wlan hardware or low-level driver implements PAE.
* 80211.o module will anyway filter frames based on authorization
* state, so this function pointer can be NULL if low-level driver does
- * not require event notification about port state changes.
- * Currently unused. */
+ * not require event notification about port state changes. */
int (*set_port_auth)(struct ieee80211_hw *hw, u8 *addr,
int authorized);
@@ -702,8 +703,9 @@
/* Get statistics of the current TX queue status. This is used to get
* number of currently queued packets (queue length), maximum queue
* size (limit), and total number of packets sent using each TX queue
- * (count).
- * Currently unused. */
+ * (count). This information is used for WMM to find out which TX
+ * queues have room for more packets and by hostapd to provide
+ * statistics about the current queueing state to external programs. */
int (*get_tx_stats)(struct ieee80211_hw *hw,
struct ieee80211_tx_queue_stats *stats);
@@ -713,12 +715,25 @@
* Must be atomic. */
u64 (*get_tsf)(struct ieee80211_hw *hw);
+ /* Call low level driver with 11n Block Ack action */
+ int (*handle_ba_action)(struct ieee80211_hw *hw,
+ struct ieee80211_mgmt *mgmt);
+
/* Reset the TSF timer and allow firmware/hardware to synchronize with
* other STAs in the IBSS. This is only used in IBSS mode. This
* function is optional if the firmware/hardware takes full care of
* TSF synchronization. */
void (*reset_tsf)(struct ieee80211_hw *hw);
+ /* Configure ht parameters. */
+ int (*conf_ht)(struct ieee80211_hw *hw,
+ struct ieee80211_ht_capability *ht_cap_param,
+ struct ieee80211_ht_additional_info *ht_extra_param);
+
+ /* Get ht capabilities from the device */
+ void (*get_ht_capab)(struct ieee80211_hw *hw,
+ struct ieee80211_ht_capability *ht_cap_param);
+
/* Setup beacon data for IBSS beacons. Unlike access point (Master),
* IBSS uses a fixed beacon frame which is configured using this
* function. This handler is required only for IBSS mode. */