wifipineapple-openwrt/target/linux/brcm47xx/patches-2.6.23/602-ssb-fix-serial-on-new-d...

91 lines
3.9 KiB
Diff

Index: linux-2.6.23.16/drivers/ssb/driver_chipcommon.c
===================================================================
--- linux-2.6.23.16.orig/drivers/ssb/driver_chipcommon.c 2008-02-19 14:37:26.000000000 +0100
+++ linux-2.6.23.16/drivers/ssb/driver_chipcommon.c 2008-02-19 14:37:27.000000000 +0100
@@ -403,6 +403,7 @@ int ssb_chipco_serial_init(struct ssb_ch
unsigned int irq;
u32 baud_base, div;
u32 i, n;
+ unsigned int ccrev = cc->dev->id.revision;
plltype = (cc->capabilities & SSB_CHIPCO_CAP_PLLT);
irq = ssb_mips_irq(cc->dev);
@@ -414,14 +415,39 @@ int ssb_chipco_serial_init(struct ssb_ch
chipco_read32(cc, SSB_CHIPCO_CLOCK_M2));
div = 1;
} else {
- if (cc->dev->id.revision >= 11) {
+ if (ccrev == 20) {
+ /* BCM5354 uses constant 25MHz clock */
+ baud_base = 25000000;
+ div = 48;
+ /* Set the override bit so we don't divide it */
+ chipco_write32(cc, SSB_CHIPCO_CORECTL,
+ chipco_read32(cc, SSB_CHIPCO_CORECTL)
+ | SSB_CHIPCO_CORECTL_UARTCLK0);
+ } else if ((ccrev >= 11) && (ccrev != 15)) {
/* Fixed ALP clock */
baud_base = 20000000;
+ if (cc->capabilities & SSB_CHIPCO_CAP_PMU) {
+ /* FIXME: baud_base is different for devices with a PMU */
+ SSB_WARN_ON(1);
+ }
div = 1;
+ if (ccrev >= 21) {
+ /* Turn off UART clock before switching clocksource. */
+ chipco_write32(cc, SSB_CHIPCO_CORECTL,
+ chipco_read32(cc, SSB_CHIPCO_CORECTL)
+ & ~SSB_CHIPCO_CORECTL_UARTCLKEN);
+ }
/* Set the override bit so we don't divide it */
chipco_write32(cc, SSB_CHIPCO_CORECTL,
- SSB_CHIPCO_CORECTL_UARTCLK0);
- } else if (cc->dev->id.revision >= 3) {
+ chipco_read32(cc, SSB_CHIPCO_CORECTL)
+ | SSB_CHIPCO_CORECTL_UARTCLK0);
+ if (ccrev >= 21) {
+ /* Re-enable the UART clock. */
+ chipco_write32(cc, SSB_CHIPCO_CORECTL,
+ chipco_read32(cc, SSB_CHIPCO_CORECTL)
+ | SSB_CHIPCO_CORECTL_UARTCLKEN);
+ }
+ } else if (ccrev >= 3) {
/* Internal backplane clock */
baud_base = ssb_clockspeed(bus);
div = chipco_read32(cc, SSB_CHIPCO_CLKDIV)
@@ -433,7 +459,7 @@ int ssb_chipco_serial_init(struct ssb_ch
}
/* Clock source depends on strapping if UartClkOverride is unset */
- if ((cc->dev->id.revision > 0) &&
+ if ((ccrev > 0) &&
!(chipco_read32(cc, SSB_CHIPCO_CORECTL) & SSB_CHIPCO_CORECTL_UARTCLK0)) {
if ((cc->capabilities & SSB_CHIPCO_CAP_UARTCLK) ==
SSB_CHIPCO_CAP_UARTCLK_INT) {
@@ -455,7 +481,7 @@ int ssb_chipco_serial_init(struct ssb_ch
cc_mmio = cc->dev->bus->mmio + (cc->dev->core_index * SSB_CORE_SIZE);
uart_regs = cc_mmio + SSB_CHIPCO_UART0_DATA;
/* Offset changed at after rev 0 */
- if (cc->dev->id.revision == 0)
+ if (ccrev == 0)
uart_regs += (i * 8);
else
uart_regs += (i * 256);
Index: linux-2.6.23.16/include/linux/ssb/ssb_driver_chipcommon.h
===================================================================
--- linux-2.6.23.16.orig/include/linux/ssb/ssb_driver_chipcommon.h 2008-02-19 14:37:26.000000000 +0100
+++ linux-2.6.23.16/include/linux/ssb/ssb_driver_chipcommon.h 2008-02-19 14:37:27.000000000 +0100
@@ -51,9 +51,12 @@
#define SSB_CHIPCO_CAP_JTAGM 0x00400000 /* JTAG master present */
#define SSB_CHIPCO_CAP_BROM 0x00800000 /* Internal boot ROM active */
#define SSB_CHIPCO_CAP_64BIT 0x08000000 /* 64-bit Backplane */
+#define SSB_CHIPCO_CAP_PMU 0x10000000 /* PMU available (rev >= 20) */
+#define SSB_CHIPCO_CAP_ECI 0x20000000 /* ECI available (rev >= 20) */
#define SSB_CHIPCO_CORECTL 0x0008
#define SSB_CHIPCO_CORECTL_UARTCLK0 0x00000001 /* Drive UART with internal clock */
#define SSB_CHIPCO_CORECTL_SE 0x00000002 /* sync clk out enable (corerev >= 3) */
+#define SSB_CHIPCO_CORECTL_UARTCLKEN 0x00000008 /* UART clock enable (rev >= 21) */
#define SSB_CHIPCO_BIST 0x000C
#define SSB_CHIPCO_OTPS 0x0010 /* OTP status */
#define SSB_CHIPCO_OTPS_PROGFAIL 0x80000000