51 lines
2.1 KiB
Diff
51 lines
2.1 KiB
Diff
From 4c1ae9f272bf34388d0fbdc99aa18af2b6c9eda1 Mon Sep 17 00:00:00 2001
|
|
From: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
|
|
Date: Wed, 29 May 2013 09:32:47 +0000
|
|
Subject: [PATCH 24/29] net: mv643xx_eth: proper initialization for Kirkwood
|
|
SoCs
|
|
|
|
Ethernet controllers found on Kirkwood SoCs not only suffer from loosing
|
|
MAC address register contents on clock gating but also some important
|
|
registers are reset to values that would break ethernet. This patch
|
|
clears the CLK125_BYPASS_EN bit for DT enabled Kirkwood only by using
|
|
of_device_is_compatible() instead of #ifdefs. Non-DT Kirkwood is not
|
|
affected as it installs a clock gating workaround because of the MAC
|
|
address issue above. Other Orion SoCs do not suffer from register reset,
|
|
do not have the bit in question, or do not have the register at all.
|
|
Moreover, system controllers on PPC using this driver should also be
|
|
protected from clearing that bit.
|
|
|
|
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
---
|
|
drivers/net/ethernet/marvell/mv643xx_eth.c | 11 +++++++++++
|
|
1 file changed, 11 insertions(+)
|
|
|
|
--- a/drivers/net/ethernet/marvell/mv643xx_eth.c
|
|
+++ b/drivers/net/ethernet/marvell/mv643xx_eth.c
|
|
@@ -116,6 +116,8 @@ static char mv643xx_eth_driver_version[]
|
|
#define LINK_UP 0x00000002
|
|
#define TXQ_COMMAND 0x0048
|
|
#define TXQ_FIX_PRIO_CONF 0x004c
|
|
+#define PORT_SERIAL_CONTROL1 0x004c
|
|
+#define CLK125_BYPASS_EN 0x00000010
|
|
#define TX_BW_RATE 0x0050
|
|
#define TX_BW_MTU 0x0058
|
|
#define TX_BW_BURST 0x005c
|
|
@@ -2700,6 +2702,15 @@ static int mv643xx_eth_probe(struct plat
|
|
|
|
mp->dev = dev;
|
|
|
|
+ /* Kirkwood resets some registers on gated clocks. Especially
|
|
+ * CLK125_BYPASS_EN must be cleared but is not available on
|
|
+ * all other SoCs/System Controllers using this driver.
|
|
+ */
|
|
+ if (of_device_is_compatible(pdev->dev.of_node,
|
|
+ "marvell,kirkwood-eth-port"))
|
|
+ wrlp(mp, PORT_SERIAL_CONTROL1,
|
|
+ rdlp(mp, PORT_SERIAL_CONTROL1) & ~CLK125_BYPASS_EN);
|
|
+
|
|
/*
|
|
* Start with a default rate, and if there is a clock, allow
|
|
* it to override the default.
|