165 lines
2.5 KiB
Plaintext
165 lines
2.5 KiB
Plaintext
/dts-v1/;
|
|
|
|
/include/ "mt7620a.dtsi"
|
|
|
|
/ {
|
|
compatible = "ralink,mt7620a-eval-board", "ralink,mt7620a-soc";
|
|
model = "Sercomm NA930";
|
|
|
|
chosen {
|
|
bootargs = "console=ttyS1,57600";
|
|
};
|
|
|
|
pinctrl {
|
|
state_default: pinctrl0 {
|
|
gpio {
|
|
ralink,group = "i2c", "rgmii2", "spi", "ephy";
|
|
ralink,function = "gpio";
|
|
};
|
|
uartf_gpio {
|
|
ralink,group = "uartf";
|
|
ralink,function = "gpio uartf";
|
|
};
|
|
};
|
|
};
|
|
|
|
palmbus@10000000 {
|
|
uart@500 {
|
|
status = "okay";
|
|
};
|
|
|
|
gpio@638 {
|
|
status = "okay";
|
|
};
|
|
|
|
gpio@660 {
|
|
status = "okay";
|
|
};
|
|
};
|
|
|
|
nand {
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
compatible = "mtk,mt7620-nand";
|
|
partition@0 {
|
|
label = "u-boot";
|
|
reg = <0x0 0x20000>;
|
|
read-only;
|
|
};
|
|
partition@200000 {
|
|
label = "factory";
|
|
reg = <0x200000 0x40000>;
|
|
read-only;
|
|
};
|
|
partition@240000 {
|
|
label = "Config";
|
|
reg = <0x240000 0x400000>;
|
|
read-only;
|
|
};
|
|
partition@640000 {
|
|
label = "firmware";
|
|
reg = <0x640000 0x1400000>;
|
|
};
|
|
};
|
|
|
|
ethernet@10100000 {
|
|
status = "okay";
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&rgmii1_pins &mdio_pins>;
|
|
|
|
ralink,port-map = "llllw";
|
|
|
|
port@4 {
|
|
status = "okay";
|
|
phy-handle = <&phy4>;
|
|
phy-mode = "rgmii";
|
|
};
|
|
|
|
port@5 {
|
|
status = "okay";
|
|
phy-handle = <&phy5>;
|
|
phy-mode = "rgmii";
|
|
};
|
|
|
|
mdio-bus {
|
|
status = "okay";
|
|
|
|
phy4: ethernet-phy@4 {
|
|
reg = <4>;
|
|
phy-mode = "rgmii";
|
|
};
|
|
|
|
phy5: ethernet-phy@5 {
|
|
reg = <5>;
|
|
phy-mode = "rgmii";
|
|
};
|
|
};
|
|
};
|
|
|
|
gpio-keys-polled {
|
|
compatible = "gpio-keys-polled";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
poll-interval = <20>;
|
|
reset {
|
|
label = "reset";
|
|
gpios = <&gpio0 11 1>;
|
|
linux,code = <0x198>;
|
|
};
|
|
zwave {
|
|
label = "zwave";
|
|
gpios = <&gpio0 12 1>;
|
|
linux,code = <0x100>;
|
|
};
|
|
wps {
|
|
label = "wps";
|
|
gpios = <&gpio0 14 1>;
|
|
linux,code = <0x211>;
|
|
};
|
|
};
|
|
|
|
gpio-leds {
|
|
compatible = "gpio-leds";
|
|
zwave {
|
|
label = "na930:blue:zwave";
|
|
gpios = <&gpio2 0 1>;
|
|
};
|
|
status {
|
|
label = "na930:blue:status";
|
|
gpios = <&gpio2 26 1>;
|
|
};
|
|
service {
|
|
label = "na930:blue:service";
|
|
gpios = <&gpio2 28 1>;
|
|
};
|
|
power {
|
|
label = "na930:blue:power";
|
|
gpios = <&gpio2 29 1>;
|
|
};
|
|
};
|
|
|
|
gpio_export {
|
|
compatible = "gpio-export";
|
|
#size-cells = <0>;
|
|
|
|
telit {
|
|
gpio-export,name = "telit";
|
|
gpio-export,output = <1>;
|
|
gpios = <&gpio0 13 0>;
|
|
};
|
|
};
|
|
|
|
gsw@10110000 {
|
|
ralink,port4 = "gmac";
|
|
};
|
|
|
|
ehci@101c0000 {
|
|
status = "okay";
|
|
};
|
|
|
|
ohci@101c1000 {
|
|
status = "okay";
|
|
};
|
|
};
|