478 lines
12 KiB
C
478 lines
12 KiB
C
/* CF-mips driver
|
|
This is a block driver for the direct (mmaped) interface to the CF-slot,
|
|
found in Routerboard.com's RB532 board
|
|
See SDK provided from routerboard.com.
|
|
|
|
Module adapted By P.Christeas <p_christeas@yahoo.com>, 2005-6.
|
|
Cleaned up and adapted to platform_device by Felix Fietkau <nbd@openwrt.org>
|
|
|
|
This work is redistributed under the terms of the GNU General Public License.
|
|
*/
|
|
|
|
#include <linux/kernel.h> /* printk() */
|
|
#include <linux/module.h> /* module to be loadable */
|
|
#include <linux/delay.h>
|
|
#include <linux/sched.h>
|
|
#include <linux/pci.h>
|
|
#include <linux/ioport.h> /* request_mem_region() */
|
|
|
|
#include <asm/gpio.h>
|
|
#include <asm/unaligned.h> /* ioremap() */
|
|
#include <asm/io.h> /* ioremap() */
|
|
#include <asm/rc32434/rb.h>
|
|
|
|
#include "ata.h"
|
|
|
|
#define REQUEST_MEM_REGION 0
|
|
#define DEBUG 1
|
|
|
|
#if DEBUG
|
|
#define DEBUGP printk
|
|
#else
|
|
#define DEBUGP(format, args...)
|
|
#endif
|
|
|
|
#define SECS 1000000 /* unit for wait_not_busy() is 1us */
|
|
|
|
unsigned cf_head = 0;
|
|
unsigned cf_cyl = 0;
|
|
unsigned cf_spt = 0;
|
|
unsigned cf_sectors = 0;
|
|
static unsigned cf_block_size = 1;
|
|
static void *baddr = 0;
|
|
|
|
#define DBUF32 ((volatile u32 *)((unsigned long)dev->baddr | ATA_DBUF_OFFSET))
|
|
|
|
|
|
static void cf_do_tasklet(unsigned long dev_l);
|
|
|
|
|
|
static inline void wareg(u8 val, unsigned reg, struct cf_mips_dev* dev)
|
|
{
|
|
writeb(val, dev->baddr + ATA_REG_OFFSET + reg);
|
|
}
|
|
|
|
static inline u8 rareg(unsigned reg, struct cf_mips_dev* dev)
|
|
{
|
|
return readb(dev->baddr + ATA_REG_OFFSET + reg);
|
|
}
|
|
|
|
static inline int cfrdy(struct cf_mips_dev *dev)
|
|
{
|
|
return gpio_get_value(dev->pin);
|
|
}
|
|
|
|
static inline void prepare_cf_irq(struct cf_mips_dev *dev)
|
|
{
|
|
rb500_gpio_set_int_level(1, dev->pin); /* interrupt on cf ready (not busy) */
|
|
rb500_gpio_set_int_status(0, dev->pin); /* clear interrupt status */
|
|
}
|
|
|
|
static inline int cf_present(struct cf_mips_dev* dev)
|
|
{
|
|
/* TODO: read and configure CIS into memory mapped mode
|
|
* TODO: parse CISTPL_CONFIG on CF+ cards to get base address (0x200)
|
|
* TODO: maybe adjust power saving setting for Hitachi Microdrive
|
|
*/
|
|
int i;
|
|
|
|
/* setup CFRDY GPIO as input */
|
|
rb500_gpio_set_func(dev->pin, 0);
|
|
gpio_direction_input(dev->pin);
|
|
|
|
for (i = 0; i < 0x10; ++i) {
|
|
if (rareg(i,dev) != 0xff)
|
|
return 1;
|
|
}
|
|
return 0;
|
|
}
|
|
|
|
static inline int is_busy(struct cf_mips_dev *dev)
|
|
{
|
|
return !cfrdy(dev);
|
|
}
|
|
|
|
static int wait_not_busy(int to_us, int wait_for_busy,struct cf_mips_dev *dev)
|
|
{
|
|
int us_passed = 0;
|
|
if (wait_for_busy && !is_busy(dev)) {
|
|
/* busy must appear within 400ns,
|
|
* but it may dissapear before we see it
|
|
* => must not wait for busy in a loop
|
|
*/
|
|
ndelay(400);
|
|
}
|
|
|
|
do {
|
|
if (us_passed)
|
|
udelay(1); /* never reached in async mode */
|
|
if (!is_busy(dev)) {
|
|
if (us_passed > 1 * SECS) {
|
|
printk(KERN_WARNING "cf-mips: not busy ok (after %dus)"
|
|
", status 0x%02x\n", us_passed, (unsigned) rareg(ATA_REG_ST,dev));
|
|
}
|
|
return CF_TRANS_OK;
|
|
}
|
|
if (us_passed == 1 * SECS) {
|
|
printk(KERN_WARNING "cf-mips: wait not busy %dus..\n", to_us);
|
|
}
|
|
if (dev->async_mode) {
|
|
dev->to_timer.expires = jiffies + (to_us * HZ / SECS);
|
|
dev->irq_enable_time = jiffies;
|
|
prepare_cf_irq(dev);
|
|
if (is_busy(dev)) {
|
|
add_timer(&dev->to_timer);
|
|
enable_irq(dev->irq);
|
|
return CF_TRANS_IN_PROGRESS;
|
|
}
|
|
continue;
|
|
}
|
|
++us_passed;
|
|
} while (us_passed < to_us);
|
|
|
|
printk(KERN_ERR "cf-mips: wait not busy timeout (%dus)"
|
|
", status 0x%02x, state %d\n",
|
|
to_us, (unsigned) rareg(ATA_REG_ST,dev), dev->tstate);
|
|
return CF_TRANS_FAILED;
|
|
}
|
|
|
|
static irqreturn_t cf_irq_handler(int irq, void *dev_id)
|
|
{
|
|
/* While tasklet has not disabled irq, irq will be retried all the time
|
|
* because of ILEVEL matching GPIO pin status => deadlock.
|
|
* To avoid this, we change ILEVEL to 0.
|
|
*/
|
|
struct cf_mips_dev *dev=dev_id;
|
|
|
|
rb500_gpio_set_int_level(0, dev->pin);
|
|
rb500_gpio_set_int_status(0, dev->pin);
|
|
|
|
del_timer(&dev->to_timer);
|
|
tasklet_schedule(&dev->tasklet);
|
|
return IRQ_HANDLED;
|
|
}
|
|
|
|
static int do_reset(struct cf_mips_dev *dev)
|
|
{
|
|
printk(KERN_INFO "cf-mips: resetting..\n");
|
|
|
|
wareg(ATA_REG_DC_SRST, ATA_REG_DC,dev);
|
|
udelay(1); /* FIXME: how long should we wait here? */
|
|
wareg(0, ATA_REG_DC,dev);
|
|
|
|
return wait_not_busy(30 * SECS, 1,dev);
|
|
}
|
|
|
|
static int set_multiple(struct cf_mips_dev *dev)
|
|
{
|
|
if (dev->block_size <= 1)
|
|
return CF_TRANS_OK;
|
|
|
|
wareg(dev->block_size, ATA_REG_SC,dev);
|
|
wareg(ATA_REG_DH_BASE | ATA_REG_DH_LBA, ATA_REG_DH,dev);
|
|
wareg(ATA_CMD_SET_MULTIPLE, ATA_REG_CMD,dev);
|
|
|
|
return wait_not_busy(10 * SECS, 1,dev);
|
|
}
|
|
|
|
static int set_cmd(struct cf_mips_dev *dev)
|
|
{
|
|
//DEBUGP(KERN_INFO "cf-mips: ata cmd 0x%02x\n", dev->tcmd);
|
|
// sector_count should be <=24 bits..
|
|
BUG_ON(dev->tsect_start>=0x10000000);
|
|
// This way, it addresses 2^24 * 512 = 128G
|
|
|
|
if (dev->tsector_count) {
|
|
wareg(dev->tsector_count & 0xff, ATA_REG_SC,dev);
|
|
wareg(dev->tsect_start & 0xff, ATA_REG_SN,dev);
|
|
wareg((dev->tsect_start >> 8) & 0xff, ATA_REG_CL,dev);
|
|
wareg((dev->tsect_start >> 16) & 0xff, ATA_REG_CH,dev);
|
|
}
|
|
wareg(((dev->tsect_start >> 24) & 0x0f) | ATA_REG_DH_BASE | ATA_REG_DH_LBA,
|
|
ATA_REG_DH,dev); /* select drive on all commands */
|
|
wareg(dev->tcmd, ATA_REG_CMD,dev);
|
|
return wait_not_busy(10 * SECS, 1,dev);
|
|
}
|
|
|
|
static int do_trans(struct cf_mips_dev *dev)
|
|
{
|
|
int res;
|
|
unsigned st;
|
|
int transfered;
|
|
|
|
//printk("do_trans: %d sectors left\n",dev->tsectors_left);
|
|
while (dev->tsectors_left) {
|
|
transfered = 0;
|
|
|
|
st = rareg(ATA_REG_ST,dev);
|
|
if (!(st & ATA_REG_ST_DRQ)) {
|
|
printk(KERN_ERR "cf-mips: do_trans without DRQ (status 0x%x)!\n", st);
|
|
if (st & ATA_REG_ST_ERR) {
|
|
int errId = rareg(ATA_REG_ERR,dev);
|
|
printk(KERN_ERR "cf-mips: %s error, status 0x%x, errid 0x%x\n",
|
|
(dev->tread ? "read" : "write"), st, errId);
|
|
}
|
|
return CF_TRANS_FAILED;
|
|
}
|
|
do { /* Fill/read the buffer one block */
|
|
u32 *qbuf, *qend;
|
|
qbuf = (u32 *)dev->tbuf;
|
|
qend = qbuf + CF_SECT_SIZE / sizeof(u32);
|
|
if (dev->tread) {
|
|
while (qbuf!=qend)
|
|
put_unaligned(*DBUF32,qbuf++);
|
|
//*(qbuf++) = *DBUF32;
|
|
}
|
|
else {
|
|
while(qbuf!=qend)
|
|
*DBUF32 = get_unaligned(qbuf++);
|
|
}
|
|
|
|
dev->tsectors_left--;
|
|
dev->tbuf += CF_SECT_SIZE;
|
|
dev->tbuf_size -= CF_SECT_SIZE;
|
|
transfered++;
|
|
} while (transfered != dev->block_size && dev->tsectors_left > 0);
|
|
|
|
res = wait_not_busy(10 * SECS, 1,dev);
|
|
if (res != CF_TRANS_OK)
|
|
return res;
|
|
};
|
|
|
|
st = rareg(ATA_REG_ST,dev);
|
|
if (st & (ATA_REG_ST_DRQ | ATA_REG_ST_DWF | ATA_REG_ST_ERR)) {
|
|
if (st & ATA_REG_ST_DRQ) {
|
|
printk(KERN_ERR "cf-mips: DRQ after all %d sectors are %s"
|
|
", status 0x%x\n", dev->tsector_count, (dev->tread ? "read" : "written"), st);
|
|
} else if (st & ATA_REG_ST_DWF) {
|
|
printk(KERN_ERR "cf-mips: write fault, status 0x%x\n", st);
|
|
} else {
|
|
int errId = rareg(ATA_REG_ERR,dev);
|
|
printk(KERN_ERR "cf-mips: %s error, status 0x%x, errid 0x%x\n",
|
|
(dev->tread ? "read" : "write"), st, errId);
|
|
}
|
|
return CF_TRANS_FAILED;
|
|
}
|
|
return CF_TRANS_OK;
|
|
}
|
|
|
|
static int cf_do_state(struct cf_mips_dev *dev)
|
|
{
|
|
int res;
|
|
switch (dev->tstate) { /* fall through everywhere */
|
|
case TS_IDLE:
|
|
dev->tstate = TS_READY;
|
|
if (is_busy(dev)) {
|
|
dev->tstate = TS_AFTER_RESET;
|
|
res = do_reset(dev);
|
|
if (res != CF_TRANS_OK)
|
|
break;
|
|
}
|
|
case TS_AFTER_RESET:
|
|
if (dev->tstate == TS_AFTER_RESET) {
|
|
dev->tstate = TS_READY;
|
|
res = set_multiple(dev);
|
|
if (res != CF_TRANS_OK)
|
|
break;
|
|
}
|
|
case TS_READY:
|
|
dev->tstate = TS_CMD;
|
|
res = set_cmd(dev);
|
|
if (res != CF_TRANS_OK)
|
|
break;;
|
|
case TS_CMD:
|
|
dev->tstate = TS_TRANS;
|
|
case TS_TRANS:
|
|
res = do_trans(dev);
|
|
break;
|
|
default:
|
|
printk(KERN_ERR "cf-mips: BUG: unknown tstate %d\n", dev->tstate);
|
|
return CF_TRANS_FAILED;
|
|
}
|
|
if (res != CF_TRANS_IN_PROGRESS)
|
|
dev->tstate = TS_IDLE;
|
|
return res;
|
|
}
|
|
|
|
static void cf_do_tasklet(unsigned long dev_l)
|
|
{
|
|
struct cf_mips_dev* dev=(struct cf_mips_dev*) dev_l;
|
|
int res;
|
|
|
|
disable_irq(dev->irq);
|
|
|
|
if (dev->tstate == TS_IDLE)
|
|
return; /* can happen when irq is first registered */
|
|
|
|
#if 0
|
|
DEBUGP(KERN_WARNING "cf-mips: not busy ok (tasklet) status 0x%02x\n",
|
|
(unsigned) rareg(ATA_REG_ST,dev));
|
|
#endif
|
|
|
|
res = cf_do_state(dev);
|
|
if (res == CF_TRANS_IN_PROGRESS)
|
|
return;
|
|
cf_async_trans_done(dev,res);
|
|
}
|
|
|
|
static void cf_async_timeout(unsigned long dev_l)
|
|
{
|
|
struct cf_mips_dev* dev=(struct cf_mips_dev*) dev_l;
|
|
disable_irq(dev->irq);
|
|
/* Perhaps send abort to the device? */
|
|
printk(KERN_ERR "cf-mips: wait not busy timeout (%lus)"
|
|
", status 0x%02x, state %d\n",
|
|
jiffies - dev->irq_enable_time, (unsigned) rareg(ATA_REG_ST,dev), dev->tstate);
|
|
dev->tstate = TS_IDLE;
|
|
cf_async_trans_done(dev,CF_TRANS_FAILED);
|
|
}
|
|
|
|
int cf_do_transfer(struct cf_mips_dev* dev,sector_t sector, unsigned long nsect,
|
|
char* buffer, int is_write)
|
|
{
|
|
BUG_ON(dev->tstate!=TS_IDLE);
|
|
if (nsect > ATA_MAX_SECT_PER_CMD) {
|
|
printk(KERN_WARNING "cf-mips: sector count %lu out of range\n",nsect);
|
|
return CF_TRANS_FAILED;
|
|
}
|
|
if (sector + nsect > dev->sectors) {
|
|
printk(KERN_WARNING "cf-mips: sector %lu out of range\n",sector);
|
|
return CF_TRANS_FAILED;
|
|
}
|
|
dev->tbuf = buffer;
|
|
dev->tbuf_size = nsect*512;
|
|
dev->tsect_start = sector;
|
|
dev->tsector_count = nsect;
|
|
dev->tsectors_left = dev->tsector_count;
|
|
dev->tread = (is_write)?0:1;
|
|
|
|
dev->tcmd = (dev->block_size == 1 ?
|
|
(is_write ? ATA_CMD_WRITE_SECTORS : ATA_CMD_READ_SECTORS) :
|
|
(is_write ? ATA_CMD_WRITE_MULTIPLE : ATA_CMD_READ_MULTIPLE));
|
|
|
|
return cf_do_state(dev);
|
|
}
|
|
|
|
static int do_identify(struct cf_mips_dev *dev)
|
|
{
|
|
u16 sbuf[CF_SECT_SIZE >> 1];
|
|
int res;
|
|
char tstr[17]; //serial
|
|
BUG_ON(dev->tstate!=TS_IDLE);
|
|
dev->tbuf = (char *) sbuf;
|
|
dev->tbuf_size = CF_SECT_SIZE;
|
|
dev->tsect_start = 0;
|
|
dev->tsector_count = 0;
|
|
dev->tsectors_left = 1;
|
|
dev->tread = 1;
|
|
dev->tcmd = ATA_CMD_IDENTIFY_DRIVE;
|
|
|
|
DEBUGP(KERN_INFO "cf-mips: identify drive..\n");
|
|
res = cf_do_state(dev);
|
|
if (res == CF_TRANS_IN_PROGRESS) {
|
|
printk(KERN_ERR "cf-mips: BUG: async identify cmd\n");
|
|
return CF_TRANS_FAILED;
|
|
}
|
|
if (res != CF_TRANS_OK)
|
|
return 0;
|
|
|
|
dev->head = sbuf[3];
|
|
dev->cyl = sbuf[1];
|
|
dev->spt = sbuf[6];
|
|
dev->sectors = ((unsigned long) sbuf[7] << 16) | sbuf[8];
|
|
dev->dtype=sbuf[0];
|
|
memcpy(tstr,&sbuf[12],16);
|
|
tstr[16]=0;
|
|
printk(KERN_INFO "cf-mips: %s detected, C/H/S=%d/%d/%d sectors=%u (%uMB) Serial=%s\n",
|
|
(sbuf[0] == 0x848A ? "CF card" : "ATA drive"), dev->cyl, dev->head,
|
|
dev->spt, dev->sectors, dev->sectors >> 11, tstr);
|
|
return 1;
|
|
}
|
|
|
|
static void init_multiple(struct cf_mips_dev * dev)
|
|
{
|
|
int res;
|
|
DEBUGP(KERN_INFO "cf-mips: detecting block size\n");
|
|
|
|
dev->block_size = 128; /* max block size = 128 sectors (64KB) */
|
|
do {
|
|
wareg(dev->block_size, ATA_REG_SC,dev);
|
|
wareg(ATA_REG_DH_BASE | ATA_REG_DH_LBA, ATA_REG_DH,dev);
|
|
wareg(ATA_CMD_SET_MULTIPLE, ATA_REG_CMD,dev);
|
|
|
|
res = wait_not_busy(10 * SECS, 1,dev);
|
|
if (res != CF_TRANS_OK) {
|
|
printk(KERN_ERR "cf-mips: failed to detect block size: busy!\n");
|
|
dev->block_size = 1;
|
|
return;
|
|
}
|
|
if ((rareg(ATA_REG_ST,dev) & ATA_REG_ST_ERR) == 0)
|
|
break;
|
|
dev->block_size /= 2;
|
|
} while (dev->block_size > 1);
|
|
|
|
printk(KERN_INFO "cf-mips: multiple sectors = %d\n", dev->block_size);
|
|
}
|
|
|
|
int cf_init(struct cf_mips_dev *dev)
|
|
{
|
|
tasklet_init(&dev->tasklet,cf_do_tasklet,(unsigned long)dev);
|
|
dev->baddr = ioremap_nocache((unsigned long)dev->base, CFDEV_BUF_SIZE);
|
|
if (!dev->baddr) {
|
|
printk(KERN_ERR "cf-mips: cf_init: ioremap for (%lx,%x) failed\n",
|
|
(unsigned long) dev->base, CFDEV_BUF_SIZE);
|
|
return -EBUSY;
|
|
}
|
|
|
|
if (!cf_present(dev)) {
|
|
printk(KERN_WARNING "cf-mips: cf card not present\n");
|
|
iounmap(dev->baddr);
|
|
return -ENODEV;
|
|
}
|
|
|
|
if (do_reset(dev) != CF_TRANS_OK) {
|
|
printk(KERN_ERR "cf-mips: cf reset failed\n");
|
|
iounmap(dev->baddr);
|
|
return -EBUSY;
|
|
}
|
|
|
|
if (!do_identify(dev)) {
|
|
printk(KERN_ERR "cf-mips: cf identify failed\n");
|
|
iounmap(dev->baddr);
|
|
return -EBUSY;
|
|
}
|
|
|
|
/* set_apm_level(ATA_APM_WITH_STANDBY); */
|
|
init_multiple(dev);
|
|
|
|
init_timer(&dev->to_timer);
|
|
dev->to_timer.function = cf_async_timeout;
|
|
dev->to_timer.data = (unsigned long)dev;
|
|
|
|
prepare_cf_irq(dev);
|
|
if (request_irq(dev->irq, cf_irq_handler, 0, "CF Mips", dev)) {
|
|
printk(KERN_ERR "cf-mips: failed to get irq\n");
|
|
iounmap(dev->baddr);
|
|
return -EBUSY;
|
|
}
|
|
/* Disable below would be odd, because request will enable, and the tasklet
|
|
will disable it itself */
|
|
//disable_irq(dev->irq);
|
|
|
|
dev->async_mode = 1;
|
|
|
|
return 0;
|
|
}
|
|
|
|
void cf_cleanup(struct cf_mips_dev *dev)
|
|
{
|
|
iounmap(dev->baddr);
|
|
free_irq(dev->irq, NULL);
|
|
#if REQUEST_MEM_REGION
|
|
release_mem_region((unsigned long)dev->base, CFDEV_BUF_SIZE);
|
|
#endif
|
|
}
|
|
|
|
|
|
/*eof*/
|