128 lines
2.0 KiB
Plaintext
128 lines
2.0 KiB
Plaintext
/dts-v1/;
|
|
|
|
/include/ "mt7620a.dtsi"
|
|
|
|
/ {
|
|
compatible = "ralink,mt7620a-eval-board", "ralink,mt7620a-soc";
|
|
model = "Ralink MT7620a + MT7610e evaluation board";
|
|
|
|
memory@0 {
|
|
reg = <0x0 0x2000000>;
|
|
};
|
|
|
|
chosen {
|
|
bootargs = "console=ttyS0,57600";
|
|
};
|
|
|
|
palmbus@10000000 {
|
|
sysc@0 {
|
|
ralink,pinmux = "spi", "uartlite", "mdio", "wled", "ephy", "rgmii1", "rgmii2";
|
|
ralink,gpiomux = "i2c", "jtag";
|
|
ralink,uartmux = "gpio";
|
|
ralink,wdtmux = <1>;
|
|
};
|
|
|
|
gpio0: gpio@600 {
|
|
status = "okay";
|
|
};
|
|
|
|
spi@b00 {
|
|
status = "okay";
|
|
|
|
m25p80@0 {
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
compatible = "en25q64";
|
|
reg = <0 0>;
|
|
linux,modalias = "m25p80", "en25q64";
|
|
spi-max-frequency = <10000000>;
|
|
|
|
partition@0 {
|
|
label = "u-boot";
|
|
reg = <0x0 0x30000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@30000 {
|
|
label = "u-boot-env";
|
|
reg = <0x30000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
factory: partition@40000 {
|
|
label = "factory";
|
|
reg = <0x40000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@50000 {
|
|
label = "firmware";
|
|
reg = <0x50000 0x7b0000>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
ethernet@10100000 {
|
|
status = "okay";
|
|
|
|
port@4 {
|
|
compatible = "lantiq,mt7620a-gsw-port", "ralink,eth-port";
|
|
reg = <4>;
|
|
phy-mode = "rgmii";
|
|
phy-handle = <&phy4>;
|
|
};
|
|
|
|
port@5 {
|
|
compatible = "lantiq,mt7620a-gsw-port", "ralink,eth-port";
|
|
reg = <5>;
|
|
phy-mode = "rgmii";
|
|
phy-handle = <&phy5>;
|
|
};
|
|
|
|
mdio-bus {
|
|
status = "okay";
|
|
|
|
phy4: ethernet-phy@4 {
|
|
reg = <4>;
|
|
phy-mode = "rgmii";
|
|
};
|
|
|
|
phy5: ethernet-phy@5 {
|
|
reg = <5>;
|
|
phy-mode = "rgmii";
|
|
};
|
|
};
|
|
};
|
|
|
|
gsw@10110000 {
|
|
status = "okay";
|
|
ralink,port4 = "gmac";
|
|
};
|
|
|
|
sdhci@10130000 {
|
|
status = "okay";
|
|
};
|
|
|
|
pcie@10140000 {
|
|
status = "okay";
|
|
};
|
|
|
|
gpio-keys-polled {
|
|
compatible = "gpio-keys";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
poll-interval = <20>;
|
|
s2 {
|
|
label = "S2";
|
|
gpios = <&gpio0 1 1>;
|
|
linux,code = <0x100>;
|
|
};
|
|
s3 {
|
|
label = "S3";
|
|
gpios = <&gpio0 2 1>;
|
|
linux,code = <0x101>;
|
|
};
|
|
};
|
|
};
|