sorry, forgot to make target/update before commiting the last patch
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43374 3c298f89-4303-0410-b956-a3cf2f4a3e73
still no sound but the codec is properly detected now, powers up and i can hear
noise on the speakers.
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43305 3c298f89-4303-0410-b956-a3cf2f4a3e73
sdhci failed to init because of this
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43293 3c298f89-4303-0410-b956-a3cf2f4a3e73
some old mt7620a uboots dont reset the pcie core properly. work around this
issue in the kernel driver.
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43292 3c298f89-4303-0410-b956-a3cf2f4a3e73
this makes gpio-poweroff work
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43254 3c298f89-4303-0410-b956-a3cf2f4a3e73
the new driver handles newer SoCs
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43250 3c298f89-4303-0410-b956-a3cf2f4a3e73
somehow all switch ports still come up as 10mbit.
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43237 3c298f89-4303-0410-b956-a3cf2f4a3e73
i accidentally dropped 2 lines while adding mt7628 support
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43216 3c298f89-4303-0410-b956-a3cf2f4a3e73
this caused a crash on boot
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43120 3c298f89-4303-0410-b956-a3cf2f4a3e73
some bootloaders (linksys e1700) set wonky hw trap values. reset this upon boot to make all ports work.
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43117 3c298f89-4303-0410-b956-a3cf2f4a3e73
latest mt7530 silicon seems to have a different phy id.
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43113 3c298f89-4303-0410-b956-a3cf2f4a3e73
Change list:
* add tx scatter gather function.
* add software rx vlan offload to let GRO work.
* add jumbo frame support. because use build_skb so max MTU is 3812.
* enable hardware tx vlan.
* enable GRO and remove LRO. because it can improve performance and can work on forwarding.
* enable/fix tx padding function.
* let napi handle tx clean up.
* support ethtool operation. now support message level, hardware status and coalesce.
* ethtool support use mdio to get phy status only on mt7620. need modify dts file and add phy info to support it.
Notes:
* build and test on rt2880, rt3052, rt3352, rt3662, rt5350 and mt7620a.
* TCP NAT performance improve. test with netperf.
- rt2880(gigabit) from 5x to 12x Mbps.
- rt3x5x from 6x to 94 Mbps.
- rt5250 from 5x to 8x Mbps.
- rt3662(gigabit) from 6x to 42x Mbps with GRO. 23x Mbps without GRO. 66x Mbps with jumbo frame.
- mt7620 still 94Mbps.
* TSO function not tested. because i don't have mt7620 with eco >= 5. and the hardware don't support to set MSS. it will have problem.
Signed-off-by: michael lee <igvtee@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43108 3c298f89-4303-0410-b956-a3cf2f4a3e73
0x8100000c vs 0x810000c0 int he pvc register this caused the cascade with an external mt7530 to fail.
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@43104 3c298f89-4303-0410-b956-a3cf2f4a3e73
the driver did not handle all states correctly causing a deadlock of the i2c hw block.
Signed-off-by: Ing.Michele Mogioni <michele.mogioni@unimc.it>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42807 3c298f89-4303-0410-b956-a3cf2f4a3e73
Targets were build tested and patches are refreshed.
Signed-off-by: Luka Perkov <luka@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42463 3c298f89-4303-0410-b956-a3cf2f4a3e73
the ohci phy was not reset properly
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42291 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is based on Jon Smirl's patch with the following changes:
- Set CS polarity as low by default.
- Add support for changing CS polarity.
- Add support for changing LSB/MSB.
- Add support for changing SPI mode.
- Fix indentations.
I tested it on a VoCore. Works fine connected to a second flash, but fails to detect MMC/SD cards due to SPI clock speed.
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42276 3c298f89-4303-0410-b956-a3cf2f4a3e73
John Crispin
Luka Perkov