These patches add support for the Astoria ARV7519RW aka Livebox 2.1
The PCI and PCIe interfaces have been disabled. Also, because there are
two revisions of this board with different GPHY firmwares, two targets
were defined.
V2: rewrote partitions to work with an u-boot specifically made for
these boards.
Signed off by: Esteban Benito <estebanjbs@gmail.com>
Signed off by: Carles Gadea <carlesgrg@gmail.com>
Tested by: José Vázquez Fernández <ppvazquezfer@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40329 3c298f89-4303-0410-b956-a3cf2f4a3e73
ARV7510PW22, ARV752DPW and ARV752DPW22 have the RT2860 eeprom stored in
flash as big-endian, but the driver needs it in little-endian format. We
have to swab it before handing it over. This requires my earlier patch
for busybox.
Funnily enough, ARV752DPW works also with the incorrect eeprom, but
undoubtedly unoptimally. I have a hunch that also the final remaining
Lantiq board would require this swabbing, but I'm not sure, so I just
swab it in the three boards that I know about.
v2:
* Swab also on ARV7510PW22 based on feedback from Alvaro Rojas
* Fix the offset with bs=2
Signed-off-by: Matti Laakso <malaakso at elisanet.fi>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40328 3c298f89-4303-0410-b956-a3cf2f4a3e73
The existing code only tries to split a parition with name "rootfs"
while actually looking for kernel+rootfs, where usually "firmware" is
used as a partition name. This doesn't make sense, as even if there
was a partition 'rootfs' given by mtdparts or via device-tree, this
code would lead to another partition called 'rootfs' being created
which would not be properly distinguished in the current user-space
code.
While potentially we could use CONFIG_MTD_SPLIT_FIRMWARE_NAME to make
that configurable, the lack of users of brnboot and the fact that we
can freely decide the partition name made me simply change the
hard-coded string constant from "rootfs" to "firmware".
(I'm going to add support for ARV7506PW which run brnboot and needs
this change)
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40324 3c298f89-4303-0410-b956-a3cf2f4a3e73
- Set correct AltSel for STP pins
- Set front button to rfkill
Signed-off-by: Antonios Vamporakis <ant@area128.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40320 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds almost full support for this board.
- WiFi is still not working
- USB will not power up. According to some reports, it may be a passive port
Signed-off-by: Antonios Vamporakis <ant@area128.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40319 3c298f89-4303-0410-b956-a3cf2f4a3e73
If gphys are not reset upstream uboot can not use them anymore.
Signed-off-by: Antonios Vamporakis <ant@area128.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40318 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds almost full support for this board. WiFi is still not working.
The FXS ports are not functional due to missing support for the TAPI driver on
VR9 SoC.
Signed-off-by: Antonios Vamporakis <ant@area128.com>
Tested-by: Luka Perkov <luka@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40317 3c298f89-4303-0410-b956-a3cf2f4a3e73
Both the GPL driver from ZyXEL and the xrx200 driver have this error. The flags
are reversed. Full duplex is marked as half and the other way around. With this
fix the switch will push full GBit speeds.
Signed-off-by: Antonios Vamporakis <ant@area128.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40312 3c298f89-4303-0410-b956-a3cf2f4a3e73
Some ARV4510PW units seem to have unstable PCI due to missing pull-up
resistors. This patch makes sure that the GPIO lines are driven properly.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39587 3c298f89-4303-0410-b956-a3cf2f4a3e73
This board is pretty similar to ARV752DPW22.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39303 3c298f89-4303-0410-b956-a3cf2f4a3e73
Arcadyan ARV4510PW has already a build profile in OpenWrt, but it is
severely lacking. This patch brings it up-to-date.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39230 3c298f89-4303-0410-b956-a3cf2f4a3e73
this was caused by not honoured error return codes of of_gpio_count()
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38878 3c298f89-4303-0410-b956-a3cf2f4a3e73
Just fixing up a few things for the Netgear DGN3500.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38733 3c298f89-4303-0410-b956-a3cf2f4a3e73
The switch is renamed to "switch0" in newer (3.10) linux kernels.
Configure the switch using vlans by default and only configure
the physical switch ports that are present.
Signed-off-by: Richard Mortimer <richm@oldelvet.org.uk>
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38673 3c298f89-4303-0410-b956-a3cf2f4a3e73
init no longer exists as a parameter
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38342 3c298f89-4303-0410-b956-a3cf2f4a3e73
John Crispin
Gabor Juhos
Luka Perkov
Hauke Mehrtens
Felix Fietkau