Read back the actual rootfs length from the image tag.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@25938 3c298f89-4303-0410-b956-a3cf2f4a3e73
I wrote a patch to add 96348SV board (aka MAGIC) support to trunk.
In my case I've found it in a Telsey "Alice W-Gate" router, fairly common
(in the past) in Italy.
I used the board definition (GPIOs, leds, ...) from the Broadcom GPL-2
relased code (here is a mirror: http://beghiero.myftp.org/sorgenti/boardparms.c )
Thanks to KanjiMonster for the support on the IRC channel.
Signed-off-by: Laurento Frittella <laurento.frittella@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@25584 3c298f89-4303-0410-b956-a3cf2f4a3e73
The device is called SPW500V, not SP500W.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@25431 3c298f89-4303-0410-b956-a3cf2f4a3e73
The fallback needs to be exported for bcm63xx, too. Runtime tested with a
BCM4322 on a BCM6358.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@25420 3c298f89-4303-0410-b956-a3cf2f4a3e73
Since bcm636x platform embeds two spi master device,
the attached patch removes static bcm_rset usage, replaced by
"bs->regs" field for all I/O operation.
Signed-off-by: Miguel Gaio <miguel.gaio@efixo.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24840 3c298f89-4303-0410-b956-a3cf2f4a3e73
This reverts commit 43511418ae2771a6662a83a254f06e37f4ac19e5.
It belongs in generic not brcm63xx.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24308 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add support for the T-Com Speedport W 500V using a special tagged image as it
identifies itself as a 96348GW, but has some gpios wired differently, and also
has only one ethernet port without a switch attached to it.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24190 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add a fixup for the kernel to check the bcm tag of the image for a boardid in
the information1 field, and use that instead of the supplied one by cfe. This
is triggered by a + at the start of the information1 field.
Also modify the image generation to generate apropriately tagged images.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24189 3c298f89-4303-0410-b956-a3cf2f4a3e73
The DSL-2740B/DSL-2741B rev C2 support was missing the board definition,
resulting in a kernel panic on boot.
This patch adds it, and also renames the generated image name to properly
reflect that it is for the revision C2, and for both the DSL-2740B and
DSL-2741B.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24188 3c298f89-4303-0410-b956-a3cf2f4a3e73
Since some devices have more than one power led, they might be separated by
their color in the name. To also allow them to be on after leaving preinit,
set any status led starting with 'power' to on instead of only those with
the exact name of 'power'.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24187 3c298f89-4303-0410-b956-a3cf2f4a3e73
Currently eth1 is hardcoded as the expected interface switches in diagmode.
This patch replaces the eth1 with the ifname, and also directly tests if
the interface specified by ifname has a switch attached.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24186 3c298f89-4303-0410-b956-a3cf2f4a3e73
Port the mechanism for different default configurations from ar71xx and
use the old configuration as the default configuration. This should have
no functional differences to before.
While we are at it, remove the obsolete nat option.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24185 3c298f89-4303-0410-b956-a3cf2f4a3e73
* Rewrote commandline parsing code using gengetopt
- We now get long options
- We have more options including use of the info section for
board information (e.g. to add the same boardid but
different GPIOs on different routers)
* Added back the ability to write stock images (this is useful, for example,
when copying the firmware from the in-memory flash, and then being
able to create an image that will let you revert to/test stock firmware
* Fixed copying of CRCs to use memcpy instead of strncpy (strncpy stops at 0)
* Added ability to use all sections of the imagetag, including custom magic
signatures (e.g. for the Telsey router I'm adding soon), info sections,
and reserved sections
* Added putting the router type (as defined in the image generating Makefile)
into the info1 section and the filesystem type in the info2 section.
This will be used by mtd (when I add the code) to return the name of
image used to flash this router. (As requested by Jo, as well as being
useful for same boardid different board scenario described above).
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24011 3c298f89-4303-0410-b956-a3cf2f4a3e73
Hauke Mehrtens
Daniel Dickinson
Florian Fainelli
Imre Kaloz
Claudio Mignanti