The RB91x boards are suffering from ethernet packet loss after a cold
boot. The cause of the problem is that the AR8035 PHYs requires special
register settings to work reliably on these boards.
Enable the RGMII TX, RX delays and disable SmartEE functionality of
the AR8035 PHYs. Also enable the RXD delay in the ETH_CFG register
to fix the issue.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40509 3c298f89-4303-0410-b956-a3cf2f4a3e73
It will be used on the RB91x boards.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40508 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add a patch for the at803x phy driver, in order to be able
to configure some register settings via platform data.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40507 3c298f89-4303-0410-b956-a3cf2f4a3e73
Forgotten patch to fix ethernet for rt2880.
Based on previously submitted patch from Claudio.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40504 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: André Valentin <avalentin@marcant.net>
Patchwork: http://patchwork.openwrt.org/patch/5101/
[juhosg: use zyxel prefix in LED names]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40500 3c298f89-4303-0410-b956-a3cf2f4a3e73
With this patch OpenWRT supports the following on the ZyXEL NBG 6716:
-WiFi 2G (ath9k)
-WiFi 5G (ath10k)
-NAND flash
-2 Ethernet interfaces
-USB 2.0
-LEDs including switch
-reasonale defaults at first boot
Signed-off-by: André Valentin <avalentin@marcant.net>
Patchwork: http://patchwork.openwrt.org/patch/5101/
[juhosg:
- rename and refresh kernel patch,
- fix a few typos,
- change button key codes,
- use zyxel prefix in LED names]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40499 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch implements support for 802.11s protected mesh wireless networks (using authsae) in the netifd framework.
Until meshd-nl80211 implements a proper -P option for the PID file, this uses shell backgrounding in order to be able to get the PID for the process.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40497 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is required to make object "session" procedure "access" dump ACLs
when no "object" or no "function" parameters are passed.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40496 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch moves ARV7519RW definitions to VR9 section from the AR9 section and removes a whitespace that breaks jffs2 image generation.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40495 3c298f89-4303-0410-b956-a3cf2f4a3e73
* add pinctrl
* fix ethernet port
* make wifi available by default
Signed-off-by: Roman Yeryomin <roman@advem.lv>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40493 3c298f89-4303-0410-b956-a3cf2f4a3e73
The last arg to FUNC() is count, not last pin.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40492 3c298f89-4303-0410-b956-a3cf2f4a3e73
This change does multiple things, all related to enable sparse usage as
a static analysis tool selectable from the OpenWrt configuration:
*add a KERNEL_SPARSE option in the config to add sparse to the kernel
build (through the C=1 option usage)
*add sparse as a new host tools. It will get selected automatically when
the above option will be enabled
Signed-off-by: Mathieu Olivari <mathieu@qca.qualcomm.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40490 3c298f89-4303-0410-b956-a3cf2f4a3e73
Patches created from tree:
git@github.com:danielschwierzeck/u-boot-lantiq.git
v2013.10..u-boot-lantiq-v2013.10-openwrt4
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40482 3c298f89-4303-0410-b956-a3cf2f4a3e73
Based on the the WNDR3700v4 support patch from Ralph Perlich:
http://patchwork.openwrt.org/patch/4763/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40481 3c298f89-4303-0410-b956-a3cf2f4a3e73
Apart from the wireless chip, the WNDR3700 v4 and the WNDR4300
is the same device. Indicate this in the kernel files.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40479 3c298f89-4303-0410-b956-a3cf2f4a3e73
The 5V power of the USB is controlled by a GPIO pin of
the external WiFi chip. Setup the GPIO bitmasks in the
platform data of the WiFi chip to ensure that the 5V
power gets enabled by the ath9k driver.
Based on the the WNDR3700v4 support patch from Ralph Perlich:
http://patchwork.openwrt.org/patch/4763/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40478 3c298f89-4303-0410-b956-a3cf2f4a3e73
Based on the the WNDR3700v4 support patch from Ralph Perlich:
http://patchwork.openwrt.org/patch/4763/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40477 3c298f89-4303-0410-b956-a3cf2f4a3e73
Based on the the WNDR3700v4 support patch from Ralph Perlich:
http://patchwork.openwrt.org/patch/4763/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40475 3c298f89-4303-0410-b956-a3cf2f4a3e73
The bootloader does not initializes the output function
correctly for all LEDs. DO that from the board setup code.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40474 3c298f89-4303-0410-b956-a3cf2f4a3e73
The hardware manual says amber so change the color part of
the LED names to reflect that. Also update the constant names.
Based on the the WNDR3700v4 support patch from Ralph Perlich:
http://patchwork.openwrt.org/patch/4763/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40473 3c298f89-4303-0410-b956-a3cf2f4a3e73
Adds support for the received signal strength indicator LEDs of the
Bullet M, Nanostation M and Rocket M devices.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/5108/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40471 3c298f89-4303-0410-b956-a3cf2f4a3e73
r39995 introduced a new parameter wps_pbc_in_m1 to wifi wps config, but
apparently did not provide a default value 0.
When that option's non-existing value is later evaluated in
/lib/netifd/hostapd.sh, it causes the "bad number" error to be logged in
syslog if user has not set the wps_pbc_in_m1 option. The error materialises
only if user has enabled wps.
Sat Apr 12 13:25:01 2014 daemon.notice netifd: radio1 (1254): sh: bad number
Sat Apr 12 13:25:01 2014 daemon.notice netifd: radio0 (1253): sh: bad number
Discussion in bug 15508: https://dev.openwrt.org/ticket/15508#comment:3
Error is caused by line 282:
https://dev.openwrt.org/browser/trunk/package/network/services/hostapd/files/netifd.sh#L282
My patch sets the parameter's default value to 0, which does nothing. The
default might also be set a bit later in the function, but this felt like the
most clear place to do that.
Signed-off-by hnyman <hannu.nyman@iki.fi>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40469 3c298f89-4303-0410-b956-a3cf2f4a3e73
According to Christophe, the kernel boots on the Soekris net5501
board.
Reported-by: Christophe Prevotaux <cprevotaux@nltinc.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40468 3c298f89-4303-0410-b956-a3cf2f4a3e73
Move the comments out from the shell script to fix build
breakage introduced in r40464.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40466 3c298f89-4303-0410-b956-a3cf2f4a3e73
John Crispin
Zoltan HERPAI
Steven Barth
Gabor Juhos
Felix Fietkau