This patch adds support for HAME MPR-A2 router using a DTS file.
The platform is Ralink RT5350.
http://wiki.openwrt.org/toh/hame/mpr-a2
Signed-off-by: Dmitry Shmygov <shmygov@rambler.ru>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36898 3c298f89-4303-0410-b956-a3cf2f4a3e73
The TP-LINK TL-MR3220 v2 has a button on the left side
labeled "WIFI". This is GPIO 24. This patch adds the
support for this button.
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36848 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds swlib attributes to the RTL8366RB switch/PHY found in the
TL-WR1043ND router that allow to mirror ethernet packets to a monitor port.
Signed-off-by: Colin Leitner <colin.leitner@googlemail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36847 3c298f89-4303-0410-b956-a3cf2f4a3e73
submitter was informed of a endinaess swap regression and replied with "works on my board"
revert the patch and make arv7518 wifi work again
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36807 3c298f89-4303-0410-b956-a3cf2f4a3e73
The port 6 of the switch is connected to the SFP
cage on the RB2011*S boards. Add a helper function
to correctly initialize the switch configuration
data on those boards to make the SFP port usable.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36799 3c298f89-4303-0410-b956-a3cf2f4a3e73
The GPIO buttons of ARV752DPW are active low.
Treating them as active high caused a reboot loop as a reset-button
press is detected by gpio-button-hotplug/gpio-keys-polled on startup.
This fixes: https://dev.openwrt.org/ticket/12642
Signed-off-by: Rafael Gieschke <rafael@gieschke.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36783 3c298f89-4303-0410-b956-a3cf2f4a3e73
On linux 3.8 the switch is named as "switch0", but the network configuration script names it as "eth0", causing no communication over ethernet due to no proper VLAN config.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36782 3c298f89-4303-0410-b956-a3cf2f4a3e73
This requires all the preceding patches and finishes support for the
DGN3500, also removing an obsolete file.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36781 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch is a device tree enhancement that IMHO is worthy of mainline.
It allows the bootloader's commandline to be preserved even when the
device tree specifies one.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36780 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch enables retrieving the wifi calibration data from an MTD
partition. It requires the previous patch.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36779 3c298f89-4303-0410-b956-a3cf2f4a3e73
This postpones the initialization of PCI and wifi until after the MTD
initialization, so that calibration data may be loaded from there.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36778 3c298f89-4303-0410-b956-a3cf2f4a3e73
This reassigns the PPPoE status to the LED that was intended to indicate
it, rather than the DSL sync light.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36777 3c298f89-4303-0410-b956-a3cf2f4a3e73
John Crispin
Luka Perkov
Felix Fietkau
Florian Fainelli
Jonas Gorski
Imre Kaloz
Gabor Juhos