Disables gluebi and enables ubiblock on lantiq xway. Squashfs
images on nand use ubifs instead of jffs2 for the overlay.
I'll leave the equivalent patch for xrx200 to someone who has a
board to test.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41565 3c298f89-4303-0410-b956-a3cf2f4a3e73
With help of this script the ath10k board.bin settings are loaded from
flash and saved to the ath10k firmware directory. The driver reads it
later in the boot process.
Signed-off-by: André Valentin <avalentin@marcant.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41562 3c298f89-4303-0410-b956-a3cf2f4a3e73
Since kernel 3.11, the third parameter passed to notifier_call()
is of type struct netdev_notifier_info. This patch fixes an oops
when setting a netdev LED trigger.
Signed-off-by: Claudio Leite <leitec@staticky.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41552 3c298f89-4303-0410-b956-a3cf2f4a3e73
Move defines and board_info structs back to their proper locations so
(de-)selecting SOC support won't break the build.
Reported-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41550 3c298f89-4303-0410-b956-a3cf2f4a3e73
A reboot is issued by setting the watchdog timer to a low value, when
the value is decreased from 1 to 0 by the hardware the system will
reboot. Setting this value to 1 does not work every time, it is a
little bit more reliable when setting it to 3. This timer runs with
some MHz or KHz so nobody will notice the increased waiting.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41548 3c298f89-4303-0410-b956-a3cf2f4a3e73
broadcom-wl now builds in the mips74k profile, so remove these chips
from the generic profile.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41546 3c298f89-4303-0410-b956-a3cf2f4a3e73
The previous attempt (r40717) to fix squashfx made the system bootable but
overlayfs remained broken.
This enables block2mtd again using the right partition number and naming
and adds MTD_ROOTFS_SPLIT option.
However onboard rootfs partition name had to be renamed to place overlay on
CF instead of onboard NAND.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41541 3c298f89-4303-0410-b956-a3cf2f4a3e73
No config option should be set to m in the default config, because
there is also some script needed which picks the module up into the
image and that is missing this way. Always create a kmod when building
a module.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41539 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is compile tested only, please run test and report back.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41538 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is compile tested only, please run test and report back.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41537 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is compile tested only, please run test and report back.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41534 3c298f89-4303-0410-b956-a3cf2f4a3e73
Most ar7 devices have only 16 MiB RAM, so select low_mem to give them
a chance to work.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41532 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is compile tested only, please run test and report back.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41531 3c298f89-4303-0410-b956-a3cf2f4a3e73
When the Ethernet controller is powered down and someone wants to
access the mdio bus like the witch driver (b53) the system crashed if
PCI_D3hot was set before. This patch deactivates this power sawing mode
when a switch driver is in use.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41527 3c298f89-4303-0410-b956-a3cf2f4a3e73
According to the thread https://forum.openwrt.org/viewtopic.php?id=48281
b53 uses GPIO 7:
[ 4.470000] b53_common: [DBG] b53_switch_reset_gpio using 7
and causes device to self-reboot. GPIO 8 was found in CFE boot log:
"Reset switch via GPIO 8 ..."
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41526 3c298f89-4303-0410-b956-a3cf2f4a3e73
Now the mac address is increased by two for the first fallback mac
address. It could be that the address increased should be used for the
wan port.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41515 3c298f89-4303-0410-b956-a3cf2f4a3e73
The address prefix 00:90:4C is used by Broadcom in their initial
configuration. When a mac address with the prefix 00:90:4C is used
all devices from the same series are sharing the same mac address.
To prevent mac address collisions we replace them with a mac address
based on the base address.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41513 3c298f89-4303-0410-b956-a3cf2f4a3e73
Without this patch the switch config for the adm switch did not worked,
because hey are not names eth0.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41512 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch deactivates the statistics, adds a missing lock
initialization and fixes a waring.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41511 3c298f89-4303-0410-b956-a3cf2f4a3e73
Reduces kernel size by about 24k (6k compressed).
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41506 3c298f89-4303-0410-b956-a3cf2f4a3e73
Old OpenWrt releases were using network configs that are not valid
anymore. They were specifying ports tagging in a different way (or were
not tagging CPU at all) and were using VID 0 which is a reserved value.
Modifying network configuration to apply all needed changes would be
pretty tricky. Script /etc/init.d/netconfig that generates new config is
quite complex itself.
So instead let's save the most important settings, regenerate config
from the scratch and restore values. This should work for 99% of users.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41500 3c298f89-4303-0410-b956-a3cf2f4a3e73
Realview is mostly used as a QEMU development platform, which will provide a
built-in DHCP server to NAT or bridge the connection outside of the emulated
environment.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41495 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is not needed since our toolchain produces the expected binaries for the
target CPU.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41494 3c298f89-4303-0410-b956-a3cf2f4a3e73
CONFIG_LEDS_GPIO_REGISTER is selected by the bcm47xx arch code.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41488 3c298f89-4303-0410-b956-a3cf2f4a3e73
this fixes the mpc85xx build error
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41477 3c298f89-4303-0410-b956-a3cf2f4a3e73
New make target in lantiq to use UbinizeImage and SysupgradeNand.
Only enabled for BTHOMEHUBV2B for the moment but should be useable
for other lantiq nand boards.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41474 3c298f89-4303-0410-b956-a3cf2f4a3e73
this broke CONFIG_ALL builds for mt7620
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41471 3c298f89-4303-0410-b956-a3cf2f4a3e73
After r41444 wifi working on WRTnode. Tested.
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41452 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds support for the MikroTik RouterBOARD SXT Lite.
The new RB911L series is also supported as a result.
v2 of this patch fixes the wmac offset to match what is on the sticker.
v3 refreshes the patch against r41148 and defines the power led as the status led in diag.sh
v4 refreshes the patch against r41353 and fixes the patch path issue to make git am work correctly
v5 selects the kernel config option in the mikrotik profile rather than in the main ar71xx config
Signed-off-by: Matthew Reeve <mreeve@tenxnetworks.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41450 3c298f89-4303-0410-b956-a3cf2f4a3e73
Enable LANTIQ_PHY and LANTIQ_XRX200 only in XRX200 subtarget.
These drivers are not needed for ASE, Danube and AR9.
As side effect PHY11G and PHY22F firmwares are not included in the
kernel image, which saves 64 KB.
Signed off by: José Vázquez Fernández <ppvazquezfer@gmail.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41449 3c298f89-4303-0410-b956-a3cf2f4a3e73
The Livebox 1 support is currently broken. Fixed with this patch
Fixes:
- Redboot partitioning broken: fixed
- Replaced custom ephy reset with platform code
- USB code breaks the building process: fixed
- Led colors
- Removed unneded EHCI code since bcm6348 only has OHCI
Signed-off-by: Daniel Gonzalez <dgcbueu@gmail.com>
[jogo: drop unneded parts since merge, fixup to apply to current head]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41424 3c298f89-4303-0410-b956-a3cf2f4a3e73
There have been no reported regressions, so backport it to 3.10.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41422 3c298f89-4303-0410-b956-a3cf2f4a3e73
Some fixes for Telsey CPVA502+ bcm6348 routers:
- reset the external PHY (eth1) with proper platform code, not using a led definiton
- eth1 is an external phy, not a switch, deleted forced link speed
- fixed led color
Patch made for 3.14 kernel patches.
Signed-off-by: Daniel Gonzalez <dgcbueu@gmail.com>
[jogo: also fix 3.14, refresh patches]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41420 3c298f89-4303-0410-b956-a3cf2f4a3e73
Spotted by several buildbots.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Patchwork: http://patchwork.openwrt.org/patch/5768/
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41391 3c298f89-4303-0410-b956-a3cf2f4a3e73
205-fix-headers_install.patch is obseleted by upstream commit 3246a0352e3d58380b9386570f1db1faf7edf8a8
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41351 3c298f89-4303-0410-b956-a3cf2f4a3e73
sorry, the downside when applying patches with patch
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41350 3c298f89-4303-0410-b956-a3cf2f4a3e73
This enables the procd nand upgrade for ZyXEL NBG 6716. Also the ubi config
is cleaned up to match the wndr4300.
Signed-off-by: André Valentin <avalentin@marcant.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41346 3c298f89-4303-0410-b956-a3cf2f4a3e73
The /lib/mvebu.sh script can now handle this task.
Signed-off-by: Luka Perkov <luka@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41341 3c298f89-4303-0410-b956-a3cf2f4a3e73
- Support set VLAN ID of each vlan.
- Support untag feature.
- Replace register address with C MACRO.
- There are 8 ports for MT7530 actually.
Signed-off-by: Xiongfei Guo <xfguo@credosemi.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41331 3c298f89-4303-0410-b956-a3cf2f4a3e73
add missing kernelnames to Makefile because those files are needed in 'target/linux/mpc83xx/image/Makefile'. Without them a compilation for mpc83xx is not possible - the buildbot stops with the error "No such file or directory"
Signed-off-by: Claudio Thomas <ct@xmodus-systems.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41330 3c298f89-4303-0410-b956-a3cf2f4a3e73
also add quotes to paths
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41326 3c298f89-4303-0410-b956-a3cf2f4a3e73
Make id more specific and consistent with others platform drivers.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41324 3c298f89-4303-0410-b956-a3cf2f4a3e73
We do not need global access to it, so move it from arch include to the
mtd subdir.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41321 3c298f89-4303-0410-b956-a3cf2f4a3e73
Pass I/O memory regions (flash read and MMR) via platform device
resources array and use them inside spiflash driver.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41320 3c298f89-4303-0410-b956-a3cf2f4a3e73
Moving the start of IO mem to 0x10000000 leads to allocation conflict
with SPI flash memory region, which starts at 0x08000000.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41319 3c298f89-4303-0410-b956-a3cf2f4a3e73
We should not detect actual flash size during board initialization to
find board config at the end of the flash, just use large enough mapping
size (currently 128 mbit). If mapping size is larger than the actual
flash size, than flash will simply be mapped multiple times. This change
simplifies code by removing duplication and saves about 200 bytes of
uncompressed kernel :)
Tested with Ubnt LS2 board equipped with STM 25p32v6p NOR flash (32 mbit).
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41317 3c298f89-4303-0410-b956-a3cf2f4a3e73
Merge 3_10-updates.patch into the ar2313_ethernet.patch since it contains
only one ethernet driver fix.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41316 3c298f89-4303-0410-b956-a3cf2f4a3e73
As far as I am aware, amongst the lantiq boards, jffs2_nand was
only used on the BTHOMEHUBV2B. Ubi-related modifications to the
device tree for that board mean that the resulting jffs2 images
no longer work, and are no longer required anyway. So I suggest
removing the related configuration, which this patch does.
If anyone else is using jffs2_nand on a lantiq target please speak
up!
Incidentally, for a jffs2 rootfs partition concatenated to the
kernel image to be recognised and mounted correctly on nand
this patch or something equivalent is required:
http://patchwork.openwrt.org/patch/5110/
It is marked as accepted in patchwork but doesn't seem to have
been committed. As far as I am concerned it too is deprecated.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41312 3c298f89-4303-0410-b956-a3cf2f4a3e73
Setting this flag allows rootfs_data to expand on first boot
to fill remaining free space on nand.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41310 3c298f89-4303-0410-b956-a3cf2f4a3e73
Use the CFE_EPTSEAL to tell them apart at runtime. Added for now only
for the 3.14 until properly tested.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41296 3c298f89-4303-0410-b956-a3cf2f4a3e73
The variant id field shift was wrong, causing the variant detection
to fail.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41295 3c298f89-4303-0410-b956-a3cf2f4a3e73
move both asus boards to asus.mk
rename HW5503G profile to HW550-3G to match name in image/Makefile
(fixes#16599)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41271 3c298f89-4303-0410-b956-a3cf2f4a3e73
At the moment, an rootfs.ubi is copied over to bin/lantiq
but rootfs-overlay.ubi is not. This adds it.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41270 3c298f89-4303-0410-b956-a3cf2f4a3e73
Revision r41256 introduced a typo (wandaboard => wandboard), but later
revisions expect to match on "wandboard"
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41262 3c298f89-4303-0410-b956-a3cf2f4a3e73
WAN and LAN are swapped the wrong way around. This patch fixes that by adding the 951Ui-2HnD to ar71xx.sh and the relevant entry in 02_network.
This patch also defines the ACT LED as the status LED in diag.sh.
Signed-off-by: Matthew Reeve <mreeve@tenxnetworks.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41255 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds factory image building for the DGN3500, all variants,
and fixes sysupgrade images to make them play nice with the sercomm
secondary boot loader.
The factory images can be used directly in the update dialog in the
interface of the stock firmware and via the special Sercomm bootmode
and a special windows flashing utility (allegedly present in the CD
that came with the device -- but it's also compatible with the NSLU2
Upgrade_207_XP utility.) The special bootmode can be activated by
turning the device on while holding the reset button pressed, then
releasing it when the power led starts blinking red and green. Please
notice that if using the 207 utility, it will always report that the
flashing failed even though it completed successfully. Just power
cycle the router manually after the utility reports the failure and
OpenWRT will boot. This same utility (despite reporting failure in
this case too) can revert a DGN3500 (any variant) to the appropriate
stock Netgear firmware.
This patch is a heavily modified version of a package I found on the
OpenWRT forum with a couple fixes and features added -- mainly the
generation of all the different image variants to support all known
models directly, atm known variants are AnnexA-WW, AnnexA-NA and
AnnexB-DE/GR.
I tested the patch successfully on my device.
Signed-off-by: Marco Antonio Mauro <marcus90@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41236 3c298f89-4303-0410-b956-a3cf2f4a3e73
This flash is used in newer Ubnt UniFi AP Pro
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41219 3c298f89-4303-0410-b956-a3cf2f4a3e73
A modified version of 552-ubifs-respect-silent-mount-flag.patch has
been merged upstream. Replace the patch in OpenWrt with the version
which has been merged.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41218 3c298f89-4303-0410-b956-a3cf2f4a3e73
Without this, the ports all end up on vlan 1. This enables a separate
WAN port that works.
Signed-off-by: Russell Senior <russell@personaltelco.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41216 3c298f89-4303-0410-b956-a3cf2f4a3e73
In a recent revision (r41177) John Crispin removed the profile for the
AsiaRF AWM002 eval board while adding another AsiaRF board. This
patch restores AWM002 and also corrects a misspelling and an
apparently errant reference to an Allnet ALL0239-3G device.
Signed-off-by: Galen Seitz <galens@seitzassoc.com>
Signed-off-by: Russell Senior <russell@personaltelco.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41215 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patches the BTHOMEHUB2B device tree to make use of the
new code for automatic detection of the ubi partition and the
rootfs type within it. Gets rid of the ugly alternative bootargs
lines.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
Acked-by: Daniel Golle <daniel@makrotopia.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41214 3c298f89-4303-0410-b956-a3cf2f4a3e73
Similar to the rootfs hacks on NOR flash devices, this series
introduces support for auto-attaching (ubi device), auto-creating
(ubiblock device) and mounting the "rootfs" (ubifs or squashfs)
volume.
This is needed so OpenWrt can start without relying on the bootloader
to pass the ubi.mtd, ubi.block, rootfs and rootfstype parameters, but
instead auto-detect the root filesystem according to a simple convention.
OpenWrt-specific:
490-ubi-auto-attach-mtd-device-named-ubi-or-data-on-boot.patch
491-ubi-auto-create-ubiblock-device-for-rootfs.patch
492-try-auto-mounting-ubi0-rootfs-in-init-do_mounts.c.patch
493-ubi-set-ROOT_DEV-to-ubiblock-rootfs-if-unset.patch
sent upstream:
552-ubifs-respect-silent-mount-flag.patch
http://lists.infradead.org/pipermail/linux-mtd/2014-May/053893.html
v2: actually retry with MS_RDONLY when mounting read-only ubifs root
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41119 3c298f89-4303-0410-b956-a3cf2f4a3e73
Use msleep(20) instead of msleep(10) to make code closer to reality
since msleep can sleep for up to 20ms even we request shorter delay.
All updated calls are located in PCI initialization routine which is
called only once upon device boot. So there should be no performance
issues caused by more longer delay.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41096 3c298f89-4303-0410-b956-a3cf2f4a3e73
Wrap lines over 80 chars or make them shorter by other ways.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41095 3c298f89-4303-0410-b956-a3cf2f4a3e73
Constify some static structures as suggested by checkpatch.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41094 3c298f89-4303-0410-b956-a3cf2f4a3e73
Use __func__ instead of gcc specific __FUNCTION__ as suggested by
checkpatch.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41093 3c298f89-4303-0410-b956-a3cf2f4a3e73
Move trailing statements to next line with indentation as suggested by
checkpatch.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41092 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add missed spaces and remove odd space as suggested by checkpatch.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41091 3c298f89-4303-0410-b956-a3cf2f4a3e73
Various indent fixes suggested by checkpatch: use tabs, use same level
of indentation for switch and case, correct indentation levels.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41090 3c298f89-4303-0410-b956-a3cf2f4a3e73
Remove some unnecessary includes and use <linux/foo.h> instead of
<asm/foo.h> when it possible as suggested by checkpatch.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41089 3c298f89-4303-0410-b956-a3cf2f4a3e73
Use more particular functions dev_<level> or pr_<level>(...) insead of
direct printk(...) call. Add KERN_LEVEL to calls what missed it.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41088 3c298f89-4303-0410-b956-a3cf2f4a3e73
Fix braces location, remove unnecessary empty lines before or after code
block, remove useless braces. All cases are detected by checkpatch.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41087 3c298f89-4303-0410-b956-a3cf2f4a3e73
Remove assignments from if conditions as suggested by checkpatch.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41084 3c298f89-4303-0410-b956-a3cf2f4a3e73
Remove parentheses around return values since return is no a function,
as suggested by checkpatch.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41083 3c298f89-4303-0410-b956-a3cf2f4a3e73
Use parenthesis around complex macroses value as suggested by
checkpatch.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41082 3c298f89-4303-0410-b956-a3cf2f4a3e73
Fix comment issues detected by checkpatch. Convert C99 // comments to
ordinary /* ... */ comments. Correct block comments style or convert
them to single line comments.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41081 3c298f89-4303-0410-b956-a3cf2f4a3e73
Change fooBar variables names to foo_bar as suggested by checkpatch,
write few tables names in lower case and correctly place __initdata
keyword.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41080 3c298f89-4303-0410-b956-a3cf2f4a3e73
With this patch the mips74k subtarget will be compiled with optimized
compiler options to generated smaller and faster code. This currently
breaks broadcom-wl, because the binary blob is only compiled with
mipsr1 support.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41050 3c298f89-4303-0410-b956-a3cf2f4a3e73
These were only used by broadcom-diag any more.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41048 3c298f89-4303-0410-b956-a3cf2f4a3e73
This fixes some strange problems with tg3. I assume that the Ethernet
driver was not brought up if the switch was named switch0.
This was reported and tested by ernesto (Faulp3lz).
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41042 3c298f89-4303-0410-b956-a3cf2f4a3e73
All new devices (with MIPS 74K CPU) are based on BCMA SoC and have
Ethernet core supported by bgmac. Create a new subtarget to generate
optimized builds.
This is just a beginning, further tweaks (like kernel configuration)
are still possible. This decreases default root.squashfs by ~128 kB.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41025 3c298f89-4303-0410-b956-a3cf2f4a3e73
Remove old irq map patch and replace it with the propper upstream patches
allowing IMX6 PCIe devices behind PCIe switches to work properly.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41004 3c298f89-4303-0410-b956-a3cf2f4a3e73
ath5k fix in wifi and ethernet eeprom handling patch.
Without the line that adds the patch of_ath5k_eeprom_probe cause a
kernel panic, at least with the ARV4518PW.
Tested only in the modem-router mentioned above.
This patch is based in Bruno's hack present in patch #5454.
Signed off by: Bruno Rodríguez <bruno.rodriguez.1980@gmail.com>
Signed off by: José Vázquez Fernández <ppvazquezfer@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40999 3c298f89-4303-0410-b956-a3cf2f4a3e73
The canutils package is in the packages repo and not part of trunk, so we
should not enable them by default.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40991 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add the following kernel modules by default (which are present on most Ventana
baseboards):
- kmod-leds-gpio (user leds)
- kmod-sound-core (required as a dependency of the other sound modules)
- kmod-pps-gpio (Pulse-Per-Second)
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40990 3c298f89-4303-0410-b956-a3cf2f4a3e73
The Gateworks Ventana board names have been adjusted per upstream patches
to include all IMX6 SoC variants.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40989 3c298f89-4303-0410-b956-a3cf2f4a3e73
update the Ventana DTS files with upstream fixes:
- The 'model' property in the imx-audio-sgtl5000 binding specifies the
user-visible name of the audio device. This should be something common and
not baseboard specific.
- removed obsolete crts
- fix include typo: The imx6q-gw51xx needs to include imx6qdl-gw51xx.dtsi
- fix gw52xx clock for sgtl5000 ananlog audio codec
- fix LVDS mapping for Ventana GW52xx/GW53xx/GW54xx
- add LVDS backlight for Ventana
- update model descriptions for all processor variants
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40988 3c298f89-4303-0410-b956-a3cf2f4a3e73
update the Ventana DTS files with upstream fixes:
- The 'model' property in the imx-audio-sgtl5000 binding specifies the
user-visible name of the audio device. This should be something common an
not baseboard specific.
- update model descriptions for all processor variants
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40987 3c298f89-4303-0410-b956-a3cf2f4a3e73
It was augmented by CONFIG_USB_GADGET...
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Tim Harvey <tharvey@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40986 3c298f89-4303-0410-b956-a3cf2f4a3e73
I added WIFI LED support (so now AP blinks nicely), I removed WPS
button GPIO (as it doesn't exist) and changed GPIO for reset button.
Signed-off-by: Jacek Kikiewicz <jaceq@aol.pl>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40976 3c298f89-4303-0410-b956-a3cf2f4a3e73
This board manufactured by HiWiFi has the following features.
- Atheros 9331 SoC.
- 16MB flash and 64MB RAM.
- 4GB eMMC storage via SK6226 USB 2.0 controller.
- 2 LAN and 1 WAN ethernet ports with LEDs on them.
- 3 blue LEDs on the front panel.
- 1 button labeled as "reset".
- Powered by a USB cable.
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40973 3c298f89-4303-0410-b956-a3cf2f4a3e73
The TL-WA730RE seems to be almost identical to TL-WA701ND, just
that it comes without PoE and a stock-firmware claiming the device
to be a "Range Extender".
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40972 3c298f89-4303-0410-b956-a3cf2f4a3e73
Detect TL-WA7510N v1 by the board name as defined in mach-tl-wa901nd.c
and add hardware ID to tplink_board_detect
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40971 3c298f89-4303-0410-b956-a3cf2f4a3e73
Dlink dir-615-e1 can use dir-600-a1's image, but the image can't be
uploaded through dlink's normal firmware update web page.
Add profile for dir-615-e1 so the generated image can be uploaded
through the firmware update web page.
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40969 3c298f89-4303-0410-b956-a3cf2f4a3e73
this patch got messed up by the last rebase
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40948 3c298f89-4303-0410-b956-a3cf2f4a3e73
modified version of -> http://patchwork.openwrt.org/patch/5535/
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40947 3c298f89-4303-0410-b956-a3cf2f4a3e73
generate sysupgrade image by combine two images.
one is kernel image with seama header.
another is root fs image.
Signed-off-by: michael lee <igvtee@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40922 3c298f89-4303-0410-b956-a3cf2f4a3e73
ARGC is a 'C-ism', but not known/valid in shell-syntax - insert the correct
var $# (=number of args) here. under normal conditions this had no impact,
but we should at least correct it. the error was observable like this:
root@box:~ [ -e "/etc/functions.sh" ] && . /etc/functions.sh
root@box:~ [ -e "/lib/functions.sh" ] && . /lib/functions.sh
root@box:~ . /lib/upgrade/platform.sh
root@box:~ . /lib/upgrade/common.sh
root@box:~ platform_check_image /tmp/myfirmware.bin
ash: bad number
root@box:~ echo $?
0
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40915 3c298f89-4303-0410-b956-a3cf2f4a3e73
The first switch case is default case. Then it will only
match default case. cause not update the lan/wan mac address.
And in the default switch case the param lan_mac is empty.
it will case error message 'arithmetic syntax error' when
call macaddr_add function.
Signed-off-by: michael lee <igvtee@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40910 3c298f89-4303-0410-b956-a3cf2f4a3e73
It is base on rt3662 soc with dual band 802.11n
wireless router. Use rtl8367R switch chip.
This patch adds a profile for this board.
It use seama image header. so i also enable it
on kernel config.
Signed-off-by: michael lee <igvtee@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40908 3c298f89-4303-0410-b956-a3cf2f4a3e73
Hi Hartmut,
Thanks for your feedback, I have reformated the patch accordingly.
Added support for Teltonika RUT5XX hardware.
Signed-off-by: Steffen Weinreich <steve@weinreich.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40907 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds "Asus RT-N10+" as a target option in menuconfig. The device has been supported for a while but is currently missing a profile (.mk).
Signed-off-by: Randolph Kuntz <8D961920@galaxymail.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40903 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds support for the PCIe controller
In addition to the PCIe controller a sprom is now provided by a device
tree driver to bcma from some nvram.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40880 3c298f89-4303-0410-b956-a3cf2f4a3e73
Support is added only for kernel 3.14 - do not show it until
the switch is made.
Following uboot env changes are needed to make it work on stock uboot:
---
setenv owrt_bootargs_root ubi.mtd=3 root=ubi0:rootfs rootfstype=ubifs rw
setenv owrt_mtdparts mtdparts=orion_nand:0x80000@0x0(uboot),0x20000@0x80000(uboot_env),0x200000@0x200000(kernel),-@0x400000(root)
setenv owrt_boot nand read.e \${loadaddr} 0x200000 0x200000 \; setenv bootargs \$(console) \$(owrt_mtdparts) \${owrt_bootargs_root} \; bootm \${loadaddr}
setenv bootcmd run owrt_boot
saveenv
---
Signed-off-by: Luka Perkov <luka@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40871 3c298f89-4303-0410-b956-a3cf2f4a3e73
550-ubifs-symlink-xattr-support.patch contains a reference to the
by now obsolete config symbol CONFIG_UBIFS_FS_XATTR which leads to
the functionality originally added by the patch in r30794 being
left-out during compile since commit 1bdcc63112a0
("UBIFS: remove xattr Kconnfig option") in v3.5.
Fix this by removing the #ifdef from all affected kernels as XATTR
support is now always enabled for UBIFS as well.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40864 3c298f89-4303-0410-b956-a3cf2f4a3e73
Revert the tagged + untagged rework for now due to regressions in
vlan setup on certain AR83xx switches.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40842 3c298f89-4303-0410-b956-a3cf2f4a3e73
The most important one is qca_force_host_mode, which also sets the
'Stream Disable' bit in the usbmode register.
Fixes usb stability issues on AR933x and AR7241/AR7242
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40841 3c298f89-4303-0410-b956-a3cf2f4a3e73
This also fixes a typo in the UBIFS_OPTS
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40827 3c298f89-4303-0410-b956-a3cf2f4a3e73
* support for pogoplug_e02 is missing
Signed-off-by: Luka Perkov <luka@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40808 3c298f89-4303-0410-b956-a3cf2f4a3e73
Replace the global "vlan_tagged" variable with an array storing the
tagging state per vlan.
The code was taken from #12181, tested and cleaned up by Saverio Proto
with additional bug fixes supplied by Álvaro Fernández.
Tested-by: Jo-Philipp Wich <jow@openwrt.org>
Signed-off-by: Saverio Proto <zioproto@gmail.com>
Signed-off-by: Álvaro Fernández <noltari@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40777 3c298f89-4303-0410-b956-a3cf2f4a3e73
We should be more careful and don't generate 128K JFFS2 images for
devices with flashes using 64K blocks (nor the other way).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40762 3c298f89-4303-0410-b956-a3cf2f4a3e73
The change is the same as ("kernel/generic: modify mtd related
patches"). Since these files are under files directory, not a files
directory of specific kernel version, better to also change them. So
it will avoid adding files to future specific files directory
(e.g. files-3.14) for this mtd related change.
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40732 3c298f89-4303-0410-b956-a3cf2f4a3e73
Function register_mtd_parser always returned 0 (at least since v3.3)
before being changed to return void in v3.14-rc1~65^2~93 (mtd: make
register_mtd_parser return void), so it's not needed to check the
return value of this function. Also add __init flag to caller.
This fix compile errors in 3.14 kernel like:
drivers/mtd/mtdsplit_seama.c: In function 'mtdsplit_seama_init':
drivers/mtd/mtdsplit_seama.c:99:2: error: void value not ignored as it ought to be
return register_mtd_parser(&mtdsplit_seama_parser);
^
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40731 3c298f89-4303-0410-b956-a3cf2f4a3e73
While at it, make spelling at little bit more consistent,
at least for my taste :-)
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40679 3c298f89-4303-0410-b956-a3cf2f4a3e73
There are two packages with the name kmod-usb-mxs-phy in OpenWrt which
causes warnings on every build.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40663 3c298f89-4303-0410-b956-a3cf2f4a3e73
These options are missing and were spotted by the buildbots.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40661 3c298f89-4303-0410-b956-a3cf2f4a3e73
With gcc-4.8 I get a compile error with kernel 3.3.
This patch fixes this problem by backporting a patch from a more recent kernel version.
CC arch/mips/mm/page.o
arch/mips/mm/page.c:89:6: error: 'clear_page' alias in between function and variable is not supported
void clear_page(void *page) __attribute__((alias("clear_page_array")));
^
arch/mips/mm/page.c:84:12: error: 'clear_page_array' aliased declaration [-Werror]
static u32 clear_page_array[0x120 / 4];
^
arch/mips/mm/page.c:108:6: error: 'copy_page' alias in between function and variable is not supported
void copy_page(void *to, void *from) __attribute__((alias("copy_page_array")));
^
arch/mips/mm/page.c:102:12: error: 'copy_page_array' aliased declaration [-Werror]
static u32 copy_page_array[0x540 / 4];
^
arch/mips/mm/page.c:108:6: error: 'copy_page' alias in between function and variable is not supported
void copy_page(void *to, void *from) __attribute__((alias("copy_page_array")));
^
arch/mips/mm/page.c:102:12: error: 'copy_page_array' aliased declaration [-Werror]
static u32 copy_page_array[0x540 / 4];
^
arch/mips/mm/page.c:89:6: error: 'clear_page' alias in between function and variable is not supported
void clear_page(void *page) __attribute__((alias("clear_page_array")));
^
arch/mips/mm/page.c:84:12: error: 'clear_page_array' aliased declaration [-Werror]
static u32 clear_page_array[0x120 / 4];
^
cc1: all warnings being treated as errors
make[7]: *** [arch/mips/mm/page.o] Error 1
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40619 3c298f89-4303-0410-b956-a3cf2f4a3e73
From 9158e3282db592e78fb32a2c8a0903ef21b97f5c Mon Sep 17 00:00:00 2001
From: Owen Kirby <osk@exegin.com>
Date: Fri, 11 Apr 2014 18:28:56 -0700
Subject: [PATCH 3/3] [at91] Add AT91 board and model name to /tmp/sysinfo.
This patch extracts the board name and model information from the /proc/device-tree
node in order to provide something a little more friendly on the LuCI sysinfo page
than just "AT91SAM9 (Device Tree)"
Signed-off-by: Owen Kirby <osk@exegin.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40598 3c298f89-4303-0410-b956-a3cf2f4a3e73
From 272f548fe8d0b811e0589e535f650f0507f6bccd Mon Sep 17 00:00:00 2001
From: Owen Kirby <osk@exegin.com>
Date: Fri, 11 Apr 2014 17:59:55 -0700
Subject: [PATCH 2/3] [at91] AT91SAM9G20-EK fixes.
While testing the 3.10 kernel update, I found that the out-of-the-box device tree for the
the AT91SAM9G20EK uses a UBIFS rootfs and stores the DTB separately from the zImage.
Signed-off-by: Owen Kirby <osk@exegin.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40597 3c298f89-4303-0410-b956-a3cf2f4a3e73
Remove get_c0_compare_int fix which is useless for latest kernels.
Tested on Ubnt Bullet2, which could successfully boot without this
workaround.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40593 3c298f89-4303-0410-b956-a3cf2f4a3e73
This reverts commit 0772ab938c0aedd7f4cc7127059d6ce8cf929dfa.
Trying to optimize calls to eth_complete_tx in this fasion causes a regression
where when sending only the tx queue can get disabled until a packet is
received. This original call to eth_schedule_poll() is scheduled so it
should not cause a performance issue.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40592 3c298f89-4303-0410-b956-a3cf2f4a3e73
r40587 added some kernel config options, on which these two ones depend.
This fixes the build of the buildbots.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40588 3c298f89-4303-0410-b956-a3cf2f4a3e73
This scripts adds a default config for the switch.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40565 3c298f89-4303-0410-b956-a3cf2f4a3e73
The 7Links PX-4885 is a small battery-powered wireless router.
It is based on a RT5350F WiSoC and features one ethernet port and one
USB port. It is a Hame MPR-A1 clone, except it has different GPIOs,
a different battery and more RAM (32 MB).
This patch adds a profile for this board, the corresponding device tree
file and the adequate base-files changes (incl. sysupgrade).
Signed-off-by: Hugo Grostabussiat <bonstra@bonstra.fr.eu.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40554 3c298f89-4303-0410-b956-a3cf2f4a3e73
BT Home Hub 2B: use overlayfs on top of ubi.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40553 3c298f89-4303-0410-b956-a3cf2f4a3e73
vr9_phy22f_a2x.bin needs to be linked in order to get ethernet support.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40543 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds port status information and MIB counters to the ADM6996
switch driver.
The driver supports also the older ADM6996L-variant, but I'm not able to
test this patch on that chip. According to the datasheet the same
registers exist there as well, so I think it should work, but any
feedback is appreciated.
Signed-off-by: Matti Laakso <malaakso at elisanet.fi>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40542 3c298f89-4303-0410-b956-a3cf2f4a3e73
The total ethernet frame length should be written to the hardware
register LTQ_ETOP_IGPLEN instead of just the value of the MTU. This
patch fixes network issues on various Danube boards, especially when
VLAN tagging is enabled.
Signed-off-by: Matti Laakso <malaakso at elisanet.fi>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40541 3c298f89-4303-0410-b956-a3cf2f4a3e73
The canbus package was recently changed to a more active project. This patch
updates the default package names to include the same functionality as before.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40531 3c298f89-4303-0410-b956-a3cf2f4a3e73
The RB91x boards are suffering from ethernet packet loss after a cold
boot. The cause of the problem is that the AR8035 PHYs requires special
register settings to work reliably on these boards.
Enable the RGMII TX, RX delays and disable SmartEE functionality of
the AR8035 PHYs. Also enable the RXD delay in the ETH_CFG register
to fix the issue.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40509 3c298f89-4303-0410-b956-a3cf2f4a3e73
It will be used on the RB91x boards.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40508 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add a patch for the at803x phy driver, in order to be able
to configure some register settings via platform data.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40507 3c298f89-4303-0410-b956-a3cf2f4a3e73
Forgotten patch to fix ethernet for rt2880.
Based on previously submitted patch from Claudio.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40504 3c298f89-4303-0410-b956-a3cf2f4a3e73
Signed-off-by: André Valentin <avalentin@marcant.net>
Patchwork: http://patchwork.openwrt.org/patch/5101/
[juhosg: use zyxel prefix in LED names]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40500 3c298f89-4303-0410-b956-a3cf2f4a3e73
With this patch OpenWRT supports the following on the ZyXEL NBG 6716:
-WiFi 2G (ath9k)
-WiFi 5G (ath10k)
-NAND flash
-2 Ethernet interfaces
-USB 2.0
-LEDs including switch
-reasonale defaults at first boot
Signed-off-by: André Valentin <avalentin@marcant.net>
Patchwork: http://patchwork.openwrt.org/patch/5101/
[juhosg:
- rename and refresh kernel patch,
- fix a few typos,
- change button key codes,
- use zyxel prefix in LED names]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40499 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch moves ARV7519RW definitions to VR9 section from the AR9 section and removes a whitespace that breaks jffs2 image generation.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40495 3c298f89-4303-0410-b956-a3cf2f4a3e73
* add pinctrl
* fix ethernet port
* make wifi available by default
Signed-off-by: Roman Yeryomin <roman@advem.lv>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40493 3c298f89-4303-0410-b956-a3cf2f4a3e73
The last arg to FUNC() is count, not last pin.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40492 3c298f89-4303-0410-b956-a3cf2f4a3e73
Based on the the WNDR3700v4 support patch from Ralph Perlich:
http://patchwork.openwrt.org/patch/4763/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40481 3c298f89-4303-0410-b956-a3cf2f4a3e73
Apart from the wireless chip, the WNDR3700 v4 and the WNDR4300
is the same device. Indicate this in the kernel files.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40479 3c298f89-4303-0410-b956-a3cf2f4a3e73
The 5V power of the USB is controlled by a GPIO pin of
the external WiFi chip. Setup the GPIO bitmasks in the
platform data of the WiFi chip to ensure that the 5V
power gets enabled by the ath9k driver.
Based on the the WNDR3700v4 support patch from Ralph Perlich:
http://patchwork.openwrt.org/patch/4763/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40478 3c298f89-4303-0410-b956-a3cf2f4a3e73
Based on the the WNDR3700v4 support patch from Ralph Perlich:
http://patchwork.openwrt.org/patch/4763/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40477 3c298f89-4303-0410-b956-a3cf2f4a3e73
Based on the the WNDR3700v4 support patch from Ralph Perlich:
http://patchwork.openwrt.org/patch/4763/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40475 3c298f89-4303-0410-b956-a3cf2f4a3e73
The bootloader does not initializes the output function
correctly for all LEDs. DO that from the board setup code.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40474 3c298f89-4303-0410-b956-a3cf2f4a3e73
The hardware manual says amber so change the color part of
the LED names to reflect that. Also update the constant names.
Based on the the WNDR3700v4 support patch from Ralph Perlich:
http://patchwork.openwrt.org/patch/4763/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40473 3c298f89-4303-0410-b956-a3cf2f4a3e73
Adds support for the received signal strength indicator LEDs of the
Bullet M, Nanostation M and Rocket M devices.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/5108/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40471 3c298f89-4303-0410-b956-a3cf2f4a3e73
John Crispin
Imre Kaloz
Felix Fietkau
Luka Perkov
Jonas Gorski
Hauke Mehrtens
Florian Fainelli
Jo-Philipp Wich
Steven Barth
Zoltan HERPAI
Gabor Juhos