Targets were build tested and patches are refreshed.
Signed-off-by: Luka Perkov <luka@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42463 3c298f89-4303-0410-b956-a3cf2f4a3e73
It it used by brcm47xx and bcm53xx targets, so put patches in generic.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42212 3c298f89-4303-0410-b956-a3cf2f4a3e73
we should check for ssb here.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42164 3c298f89-4303-0410-b956-a3cf2f4a3e73
This adds some code based on code from the Broadcom GPL tar to fix the
reboot problems on BCM4705/BCM4785. I tried rebooting my device for ~10
times and have never seen a problem. This reverts the changes in the
previous commit and adds the real fix as suggested by Rafał.
Setting bit 22 in Reg 22, sel 4 puts the BIU (Bus Interface Unit) into
async mode.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42088 3c298f89-4303-0410-b956-a3cf2f4a3e73
A reboot is issued by setting the watchdog timer to a low value, when
the value is decreased from 1 to 0 by the hardware the system will
reboot. Setting this value to 1 does not work every time, it is a
little bit more reliable when setting it to 3. This timer runs with
some MHz or KHz so nobody will notice the increased waiting.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41548 3c298f89-4303-0410-b956-a3cf2f4a3e73
When the Ethernet controller is powered down and someone wants to
access the mdio bus like the witch driver (b53) the system crashed if
PCI_D3hot was set before. This patch deactivates this power sawing mode
when a switch driver is in use.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41527 3c298f89-4303-0410-b956-a3cf2f4a3e73
Now the mac address is increased by two for the first fallback mac
address. It could be that the address increased should be used for the
wan port.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41515 3c298f89-4303-0410-b956-a3cf2f4a3e73
The address prefix 00:90:4C is used by Broadcom in their initial
configuration. When a mac address with the prefix 00:90:4C is used
all devices from the same series are sharing the same mac address.
To prevent mac address collisions we replace them with a mac address
based on the base address.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41513 3c298f89-4303-0410-b956-a3cf2f4a3e73
Handle it by creating a new patch for simple database changes.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40345 3c298f89-4303-0410-b956-a3cf2f4a3e73
Rafał Miłecki
Felix Fietkau
Luka Perkov
Hauke Mehrtens