On UBI enabled devices, U-Boot might store it's environment on
UBI volume(s). Support this in uboot-envtools, so fw_setenv and
fw_printenv can work on these platforms.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40929 3c298f89-4303-0410-b956-a3cf2f4a3e73
Use InstallDev to make libubi-utils available for linking in
uboot-envtools.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40928 3c298f89-4303-0410-b956-a3cf2f4a3e73
The find(1) -perm +mode is no longer supported and has been deprecated since
2005.
This could resolve#13855 ticket.
Signed-off-by: Rocco Folino <lordzen87@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40927 3c298f89-4303-0410-b956-a3cf2f4a3e73
generate sysupgrade image by combine two images.
one is kernel image with seama header.
another is root fs image.
Signed-off-by: michael lee <igvtee@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40922 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch series is extracted from
http://ftp.de.debian.org/debian/pool/main/g/genext2fs/genext2fs_1.4.1-4.debian.tar.gz
The patches are used in Debian for quite a long time, so I assume that
this is solid material. At least, my Ubuntu host fsck.ext4 does not bark :-)
The goal is to allow building filesystems with larger blocksizes instead of the
current default of 1k. This should improve performance and lifetime when the
filesystem is stored e.g. on a SD card (on Raspberry Pi/I2SE Duckbill for example)
which uses internal flash memory. Writing to flash memory is slow because writing
the data of one block results in erasing a whole erase block of the flash memory.
Thus it is preferable to align the filesystem block size on a flash device with
the erase blocksize, or at least bring it closer to the later one, to avoid
unnecessary write amplification.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40921 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds support for building the kernel modules for gadget serial devices.
Signed-off-by: Owen Kirby <osk@exegin.com>
Acked-by: Tim Harvey <tharvey@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40917 3c298f89-4303-0410-b956-a3cf2f4a3e73
when disabling ipv6, the iptables build breaks without a manul clean or this patch
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40916 3c298f89-4303-0410-b956-a3cf2f4a3e73
ARGC is a 'C-ism', but not known/valid in shell-syntax - insert the correct
var $# (=number of args) here. under normal conditions this had no impact,
but we should at least correct it. the error was observable like this:
root@box:~ [ -e "/etc/functions.sh" ] && . /etc/functions.sh
root@box:~ [ -e "/lib/functions.sh" ] && . /lib/functions.sh
root@box:~ . /lib/upgrade/platform.sh
root@box:~ . /lib/upgrade/common.sh
root@box:~ platform_check_image /tmp/myfirmware.bin
ash: bad number
root@box:~ echo $?
0
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40915 3c298f89-4303-0410-b956-a3cf2f4a3e73
When using the options EXTERNAL_KERNEL_TREE or KERNEL_GIT_CLONE_URI,
the command "make downloads" fails as it tries to download the kernel
tarball despite the option. This doesn't happen during a regular build
as in that case, the dependency is conditionned through the LINUX_SITE
variable, which is not set in these cases.
Below is a snapshot of the error for an target using a 3.14 kernel:
make[3]: *** No rule to make target `.../dl/linux-3.14.tar.xz',
needed by `download'. Stop.
Change-Id: I1244969c1bbf9c81a6a64d68ae88ac58b0f8e79e
Signed-off-by: Mathieu Olivari <mathieu@qca.qualcomm.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40913 3c298f89-4303-0410-b956-a3cf2f4a3e73
Function service_kill is deprecated and has no user, so remove it.
Signed-off-by: Zhao, Gang <gamerh2o@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40912 3c298f89-4303-0410-b956-a3cf2f4a3e73
The first switch case is default case. Then it will only
match default case. cause not update the lan/wan mac address.
And in the default switch case the param lan_mac is empty.
it will case error message 'arithmetic syntax error' when
call macaddr_add function.
Signed-off-by: michael lee <igvtee@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40910 3c298f89-4303-0410-b956-a3cf2f4a3e73
Since svn rev [38557] we support power buttons, for example
the ACPI power button on x86 machines.
Add a simple shutdown script to /etc/rc.button, to gracefully shutdown
the machine after the power button is pressed.
Tested on x86 and x86_64 in a kvm virtual machine.
Signed-off-by: Stefan Hellermann <stefan@the2masters.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40909 3c298f89-4303-0410-b956-a3cf2f4a3e73
It is base on rt3662 soc with dual band 802.11n
wireless router. Use rtl8367R switch chip.
This patch adds a profile for this board.
It use seama image header. so i also enable it
on kernel config.
Signed-off-by: michael lee <igvtee@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40908 3c298f89-4303-0410-b956-a3cf2f4a3e73
Hi Hartmut,
Thanks for your feedback, I have reformated the patch accordingly.
Added support for Teltonika RUT5XX hardware.
Signed-off-by: Steffen Weinreich <steve@weinreich.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40907 3c298f89-4303-0410-b956-a3cf2f4a3e73
Before this patch, doing `/e/c/network restart' will emit the folloing
error by `ubus network.wireless down "{}"' because netifd already quit
by that time.
Command failed: not found
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40906 3c298f89-4303-0410-b956-a3cf2f4a3e73
The chipidea USB OTG controller is dual-role and supports both host and device
modes. Enable device mode.
Tested on Gateworks Ventana imx6 board with g_ether.
Are there any other targets out there that use the CHIPIDEA controller? If so
testing is needed for those.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40905 3c298f89-4303-0410-b956-a3cf2f4a3e73
Since logd haven't started at this point, logging does not work.
Signed-off-by: Nuno Goncalves <nunojpg@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40904 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds "Asus RT-N10+" as a target option in menuconfig. The device has been supported for a while but is currently missing a profile (.mk).
Signed-off-by: Randolph Kuntz <8D961920@galaxymail.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40903 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch adds support for the PCIe controller
In addition to the PCIe controller a sprom is now provided by a device
tree driver to bcma from some nvram.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40880 3c298f89-4303-0410-b956-a3cf2f4a3e73
Patch sets the source IP address of DHCP request messages during rebind to the IP address
assigned to the udhcpc client. Source address 0.0.0.0 can only be used by a client prior
to obtaining its IP address (see RFC2131 § 4.1). Source IP address behavior lines up now with
the ISC dhcp client implementation for DHCP request messages during rebind and DHCP release
messages.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40878 3c298f89-4303-0410-b956-a3cf2f4a3e73
John Crispin
Felix Fietkau
Luka Perkov
Steven Barth
Zoltan HERPAI
Hauke Mehrtens
Jo-Philipp Wich