Commit Graph

25 Commits (e6653d50fb83c9f522b2f4d819dbb5d3ebe481cd)

Author SHA1 Message Date
Hauke Mehrtens 020ac4da2b brcm47xx: don't create named switch_vlan sections
It doesn't seem to be used anywhere, it's incompatible with other
targets and can be confusing. People may think they need to update
section name every time they change VLAN ID (well, even I was doing
that).

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>


git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41835 3c298f89-4303-0410-b956-a3cf2f4a3e73
2014-07-26 12:33:48 +00:00
Hauke Mehrtens 8e570d48b0 brcm47xx: fix special board handling for some devices
Some devices were renamed when converted from diag to in kernel board detection and it was not changed in netconfig. Devices not in the 
kernel board detection are removed now.

This should close: #17111, #16968, #13202

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>



git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41663 3c298f89-4303-0410-b956-a3cf2f4a3e73
2014-07-14 22:16:19 +00:00
Hauke Mehrtens 8b171622cd brcm47xx: get switch name from swconfig first
Without this patch the switch config for the adm switch did not worked, 
because hey are not names eth0.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>


git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41512 3c298f89-4303-0410-b956-a3cf2f4a3e73
2014-07-05 12:15:03 +00:00
Hauke Mehrtens 0f7a9d7a21 brcm47xx: migrate basic network settings from old releases
Old OpenWrt releases were using network configs that are not valid
anymore. They were specifying ports tagging in a different way (or were
not tagging CPU at all) and were using VID 0 which is a reserved value.

Modifying network configuration to apply all needed changes would be
pretty tricky. Script /etc/init.d/netconfig that generates new config is
quite complex itself.
So instead let's save the most important settings, regenerate config
from the scratch and restore values. This should work for 99% of users.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>


git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41500 3c298f89-4303-0410-b956-a3cf2f4a3e73
2014-07-03 21:40:59 +00:00
Hauke Mehrtens 6143a2a98d bcm47xx: use eth0 for switch name
This fixes some strange problems with tg3. I assume that the Ethernet 
driver was not brought up if the switch was named switch0.

This was reported and tested by ernesto (Faulp3lz).

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>


git-svn-id: svn://svn.openwrt.org/openwrt/trunk@41042 3c298f89-4303-0410-b956-a3cf2f4a3e73
2014-06-07 15:41:41 +00:00
Hauke Mehrtens fbc1c16f1b brcm47xx: parse model from cpuinfo
Instead of looking into the proc entry provided by broadcom-diag use
the board info from /proc/cpuinfo to get the board we are on.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>


git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39256 3c298f89-4303-0410-b956-a3cf2f4a3e73
2014-01-12 18:56:57 +00:00
Hauke Mehrtens 3d734a755e brcm47xx: fix led indication
Use the new led api also on brcm47xx.
The led for failsafe indication is searched for.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>


git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39255 3c298f89-4303-0410-b956-a3cf2f4a3e73
2014-01-12 18:56:36 +00:00
Hauke Mehrtens a51770782a brcm47xx: use "firmware" partition name
Some time ago, after switching to the mainline bcm47xxpart driver
following patch has been applied:

commit 03cef8725d2062335ffc3de50fc037b294fd458c
Author: hauke <hauke@3c298f89-4303-0410-b956-a3cf2f4a3e73>
Date:   Sat Apr 6 22:22:26 2013 +0000

    brcm47xx: use old partition names again for kernel 3.8

    This fixes sysupgrade. The partition names are used all over the Internet in various howtos.

    Thank you russell for spotting this problem.

I propose to revert this change and make sysupgrade use "firmware"
instead. This makes brcm47xx compatible with widely used ar71xx and
after all "firmware" sounds like a much better name for... the firmware.

This change doesn't affect "sysupgrade" usage, because it never takes a
partition name as a parameter. This change only affects users using mtd
tool directly. Hopefully there are not many howtos using "mtd" command.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>


git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38973 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-12-01 16:32:32 +00:00
Hauke Mehrtens 92de1b3c56 brcm47xx: fix netconfig for inverted vlan?ports in nvram
This was observed on the Belkin Share F7D7302.


git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38769 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-11-11 23:04:47 +00:00
Hauke Mehrtens 32654ebc00 brcm47xx: add support for ipv6 in default network config
Modify /etc/init.d/netconfig to use UCI defaults for building the
default network config, which includes appropriate defaults for IPV6.

Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>


git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38294 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-10-02 23:22:18 +00:00
Hauke Mehrtens 7809178e44 brcm47xx: run mtd fixtrx linux every time
With this patch it is possible to boot a device with kernel 3.10 a second time.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>


git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37625 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-07-31 17:41:52 +00:00
Hauke Mehrtens 4cd2167005 brcm47xx: use b53 phy driver for the switch in kernel 3.10
This makes it possible to use swconfig to controll the switch.

This was tested with devices using b43 and bgmac.
This was not tested on devices using tg3.
This does not support the adm switch used in some very old devices.


git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37304 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-07-14 14:11:17 +00:00
Hauke Mehrtens 94d356b7e1 brcm47xx: use old partition names again for kernel 3.8
This fixes sysupgrade. The partition names are used all over the Internet in various howtos.

Thank you russell for spotting this problem.


git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36235 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-04-06 22:22:26 +00:00
Hauke Mehrtens a5d279ddec brcm47xx: netconfig: add bacis support for swconfig
Parse the cpu port from swconfig and explicitly mark the cpu port as tagged.


git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35911 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-03-09 19:24:43 +00:00
Hauke Mehrtens 9f5d8143f7 brcm47xx: do not use vlan0 any more.
The Broadcom switch driver says that vlan0 should not be used with any switch other than bcm5325.

This makes OpenWrt always use vlan1 and vlan2 instead.



git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35704 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-20 15:31:43 +00:00
Hauke Mehrtens 9f9982c1f7 brcm47xx: add initial support for kernel 3.8
This contains the following new bigger changes:
 * new partition parser which still could lake some features or have bugs
 * new nand flash driver
 * using physmap-flash flash driver for parallel flash
 * some changes to the serial flash driver

With these changes OpenWrt starts using more of the mainline flash drivers.


git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35632 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-16 20:28:24 +00:00
Hauke Mehrtens 28fd5cda23 brcm47xx: fix network config on simpleshare
The included patch will generate a correct network configuration on the simpletech simpleshare.

Thank you for the patch Will Holmes (RealOpty)

This closes #12361.


git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35623 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-16 15:24:48 +00:00
Hauke Mehrtens 117f7697ec brcm47xx: try to automatically detect if the wan port is at port 4 and not at port 0.
This should fix #13000.


git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35617 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-16 12:37:24 +00:00
Hauke Mehrtens 8f8b2b4cd0 brcm47xx: if the cpuport of the switch is port 8 assume vlan0ports: "1 2 3 4 8" and vlan0ports: "0 8"
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35597 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-14 12:38:16 +00:00
Hauke Mehrtens 6891eecd2a brcm47xx: configure vlan correctly on some recent devices.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35587 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-13 16:05:52 +00:00
Hauke Mehrtens b753276ff5 brcm47xx: Fix switch config on 4716/53115 devices
Signed-off-by: Jonathan McCrohan <jmccrohan@gmail.com>


git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35490 3c298f89-4303-0410-b956-a3cf2f4a3e73
2013-02-04 22:38:37 +00:00
Hauke Mehrtens e6ea8f615c brcm47xx: Additional BCM4716 support
Additional BCM4716 support.  Still needs working ethernet driver.

Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>


git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34672 3c298f89-4303-0410-b956-a3cf2f4a3e73
2012-12-13 18:57:38 +00:00
Florian Fainelli eb0d293c25 [brcm47xx]: add vlan definitions for Siemens SE505v2
Hi,

this patch adds the correct vlan definitions for the Siemens SE505v2. It
applies to trunk as well as backfire (please apply here too). On
backfire this also patches brcm-2,4, because brcm47xx base-files is just
symlinked to brcm-2.4.

It also fixes two whitespace issues.

Tested with brcm47xx on both trunk and backfire branch and works as
expected.

Signed-off-by: Manuel Munz <freifunk@somakoma.de>

git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28336 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-09-30 12:55:33 +00:00
Jo-Philipp Wich 7dd8956343 [brcm47xx] fix the default network configuration for the ASUS WL-330gE (#8751)
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@28024 3c298f89-4303-0410-b956-a3cf2f4a3e73
2011-08-17 03:16:59 +00:00
Felix Fietkau 19a9284b9a add back the base-files/image code from brcm-2.4 to brcm47xx
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@21945 3c298f89-4303-0410-b956-a3cf2f4a3e73
2010-06-26 20:41:49 +00:00