This allows IPv6 to set up without IPv4 being up thus
IPv6-only or IPv6+DS-Lite working with the default config.
Signed-off-by: Steven Barth <steven@midlink.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@42848 3c298f89-4303-0410-b956-a3cf2f4a3e73
According to Christophe, the kernel boots on the Soekris net5501
board.
Reported-by: Christophe Prevotaux <cprevotaux@nltinc.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40468 3c298f89-4303-0410-b956-a3cf2f4a3e73
Place the previous selection (3.3.8) into the only subtarget that did
not override it to 3.10
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40454 3c298f89-4303-0410-b956-a3cf2f4a3e73
Backport net5501 platform driver from 3.4.
Remove vestiges of old (pre-2.6.30) leds-net5501.c driver.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30021 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patches the CFLAGS for Geode LX CPUs for 4.3 and new GGC versions. This creates more compatible code and allowed me to boot my system first time with no troubles. Also, the missing kmod is added in.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@30013 3c298f89-4303-0410-b956-a3cf2f4a3e73
Remove packages which are dependencies of other packages
Remove packages which are part of the default package list
Remove DSL specific packages from net5501
Remove bridge package, we use the busybox applet
Replace hostapd with wpad
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29999 3c298f89-4303-0410-b956-a3cf2f4a3e73
Bump to version 3.2.
Simplify and correct kernel config (based on x86/config-3.2).
Designate eth0 as wan interface, and bridge eth1/eth2/eth3.
Add heartbeat LED trigger.
Use correct CS5535 GPIO driver.
Use correct USB drivers (OHCI not UHCI).
Add MSR and HW clock support.
Add GPIO mask definition.
Add correct SATA drivers.
Add LED triggers.
[Patch from Philipp Prindeville, via http://patchwork.openwrt.org/patch/1802/]
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@29994 3c298f89-4303-0410-b956-a3cf2f4a3e73
CONFIG_X86_GENERIC obscures CONFIG_MGEODE_LX, etc. and causes it to use wrong cache-line size.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@24071 3c298f89-4303-0410-b956-a3cf2f4a3e73
Since the net5501 doesn't have a VGA port, it doesn't need HID support either --
all console access will be over a serial port.
Also add FEATURES to it as well.
Signed-of-by: Philip Prindeville <philip@redfish-solutions.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@23916 3c298f89-4303-0410-b956-a3cf2f4a3e73
Makes the builds run slightly faster on multicores.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@23495 3c298f89-4303-0410-b956-a3cf2f4a3e73
This patch brings up the net5501 platform.
Note that the x86/ target included support for all x86/ class
processors. That's not technically correct. This should be constrained
only to the "generic" subtarget. Every x86-class target that isn't
generic should be able to select only the optimizations/capabilities
applicable to that architectural variant.
It's also assumed that all x86 processors have keyboard & mouse ports,
ISA, DMI, ACPI... the embedded ones typically don't. Again, moving
that to the generic subtarget.
Fortunately, this was a fairly benign tweak.
The net5501 board includes the following logic:
Geode/LX processor
CS5535 super-I/O chip
PC87360 sensor chip
Via Rhine Ethernet controllers
Via Sata controllers
USB, LEDS, I2C
Signed-off-by: Philip Prindeville <philipp_subx@redfish-solutions.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@20794 3c298f89-4303-0410-b956-a3cf2f4a3e73
Steven Barth
Gabor Juhos
Felix Fietkau
Jonas Gorski
Jo-Philipp Wich
Florian Fainelli
Nicolas Thill