BCM6358 requires further work due to its shared TLB.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36526 3c298f89-4303-0410-b956-a3cf2f4a3e73
/proc/irq is needed for changing the SMP affinity of interrupts.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36525 3c298f89-4303-0410-b956-a3cf2f4a3e73
Use busnum 1 for HSSPI so it won't conflict on chips having both SPI
controllers.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36524 3c298f89-4303-0410-b956-a3cf2f4a3e73
This change is based on a patch by Karl Palsson <karlp@remake.is>
See http://patchwork.openwrt.org/patch/3536/.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36513 3c298f89-4303-0410-b956-a3cf2f4a3e73
And while at it, also include a define check for BCM6328, thanks to
Gabor for spotting this.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36506 3c298f89-4303-0410-b956-a3cf2f4a3e73
Thanks to Emilio Arias for reporting it.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36505 3c298f89-4303-0410-b956-a3cf2f4a3e73
Update the numbering of kernel patch for supporting
Netgear WNR2000v3 from 617 to 618.
Signed-off-by: yousong <yszhou4tech@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36498 3c298f89-4303-0410-b956-a3cf2f4a3e73
It is forced to 'y' since r36342.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36490 3c298f89-4303-0410-b956-a3cf2f4a3e73
I recently picked up a WNDR3700 to put OpenWRT on, and only after tearing into the box did I find it
was one of the v3 boards, with poor OpenWRT support. This patch should add the board detection and
LED/button control to the broadcom-diag module, and should generate a netgear .chk image that the
bootloader and stock firmware will accept.
The changes to the broadcom-diag module are more than a few lines because the WNDR3700v3 is driving
its LEDs through an HC164 8-bit shift register.
Signed-off-by: Owen Kirby <osk@exegin.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36482 3c298f89-4303-0410-b956-a3cf2f4a3e73
The biggest change with this kernel is a new partition parser.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36480 3c298f89-4303-0410-b956-a3cf2f4a3e73
allocate_partition() copies all the content of dpart into a new struct.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36475 3c298f89-4303-0410-b956-a3cf2f4a3e73
Fixes build failure when having kmod-mmc and brcmfmac selected.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36468 3c298f89-4303-0410-b956-a3cf2f4a3e73
Network connectivity works fine (LAN and WAN).
For GPIOs, only pwr led and the green wan leds are supported for now.
Signed-off-by: Mathieu Olivari <mathieu.olivari@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36459 3c298f89-4303-0410-b956-a3cf2f4a3e73
Add support for TPLINK WR720N v3 which has 4MB flash,
32MB ram, 2 ethernet interfaces, 1 USB 2.0 port.
The patch is mostly a modification from mach-tl-wr703n.c.
GPIO numbers for the slider switch is from mach-tl-mr3020n.c.
Tested on my device and they worked fine.
Signed-off-by: yousong <yszhou4tech@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36456 3c298f89-4303-0410-b956-a3cf2f4a3e73
Only difference between Generic and P1020 is that P1020
enables SMP with two CPUs in the kernel config.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36454 3c298f89-4303-0410-b956-a3cf2f4a3e73
This upgrades the AT91 target to 3.8.7, and migrates to device tree.
This allows a single kernel to be built for most at91 variants which
simplifies things quite a bit. The immediate result is that all
subtargets are nuked, and any boards without dts files are no longer
supported, though the target now includes more boards than before. The
adc driver was also nuked as 3.8.7 includes a new one under the IIO
subsystem.
Signed-off-by: Adam Porter <porter.adam@gmail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36452 3c298f89-4303-0410-b956-a3cf2f4a3e73
drivers/net/phy/rtl8366_smi.c: In function 'rtl8366_sw_set_vlan_ports':
drivers/net/phy/rtl8366_smi.c:1125:6: warning: 'pvid' may be used uninitialized in this function [-Wuninitialized]
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36442 3c298f89-4303-0410-b956-a3cf2f4a3e73
Now that ALL5002 and ALL5003 each got their own DTS and board names, remove
the now no longer needed user-space part which previously differentiated between
ALL5002 and ALL5003.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
Patchwork: http://patchwork.openwrt.org/patch/3558/
Acked-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36436 3c298f89-4303-0410-b956-a3cf2f4a3e73
Prior to the switch to 3.8, ALL5002 and ALL5003 boards shared mach-all5002.c.
With the change to DTS, this is no longer accurate, as ALL5002 is based on
Rt3352 SoC while ALL5003 is based on Rt5350 SoC, therefore the corresponding
rt5350.dtsi need to be included for ALL5003.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
Patchwork: http://patchwork.openwrt.org/patch/3557/
Acked-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36435 3c298f89-4303-0410-b956-a3cf2f4a3e73
This makes any ramips device accessible via ethernet in failsafe mode.
Based on: https://dev.openwrt.org/changeset/36322
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/3567/
Acked-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36434 3c298f89-4303-0410-b956-a3cf2f4a3e73
This board uses a TrendChip SOC with its own RAM/Flash for ADSL support.
We know both SOCs are connected through ethernet and use some kind of protocol for UART communication, but due to the lack of GPL sources we couldn't get it to work. For this reason the network is configured only for LAN.
There are two versions (Chile 8MB and Spain 16MB).
Wiki: http://wiki.openwrt.org/toh/alpha/asl26555
Signed-off-by: Esteban Benito <estebanjbs@gmail.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/3571/
Acked-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36433 3c298f89-4303-0410-b956-a3cf2f4a3e73
Jonas Gorski
Jo-Philipp Wich
Gabor Juhos
Florian Fainelli
John Crispin
Hauke Mehrtens