This prevents private traffic from leaking out to the internet
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35012 3c298f89-4303-0410-b956-a3cf2f4a3e73
Allow bcm63xxpart to receive a caldata offset if calibration data is contained in flash.
Tested-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35010 3c298f89-4303-0410-b956-a3cf2f4a3e73
3.6 is tested enough to be considered stable.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35009 3c298f89-4303-0410-b956-a3cf2f4a3e73
remove firmware for LP-Phy core rev 14, I have never seen such a device.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35000 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is based on a patch send by Nathan Hintz <nlhintz@hotmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34997 3c298f89-4303-0410-b956-a3cf2f4a3e73
This adds diag leds/buttons support for Linksys E1000 V1. It worked on
my router, however it may need some tweaking by people more familiar
with openwrt and c to make it fit for commiting.
Thank you hhm for this patch.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34996 3c298f89-4303-0410-b956-a3cf2f4a3e73
This Ethernet driver is in early development stage and still has some problems.
This was working on my bcm4716 based device.
Thanks to Rafał Miłecki <zajec5@gmail.com> for writing this driver.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34995 3c298f89-4303-0410-b956-a3cf2f4a3e73
In addition check_module is not needed, nobody checks the return value.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34993 3c298f89-4303-0410-b956-a3cf2f4a3e73
I wrote this patch some time ago because I had a need for one of the
Gigabit ports (Linksys E3000) to be forced to 100FD. This is based
on the robocfg sources included w/ the RT-N16 sources from ASUS.
Since work is progressing on a BGMAC driver that could be included in
OpenWRT, this may be useful to someone else.
In testing, forcing the speed to 10/100 or 1000 worked fine; however,
when trying to force full-duplex mode, the result was always
half-duplex. I was not able to isolate the source of the problem
(this patch, driver or H/W limitation). The only way I could get it
to work was to set the port to Auto, but then only advertise 100FD
(not included in this patch).
I have a modified version of the robocfg package as well, I'd have to
clean it up a little first (remove the full-duplex hack) before
submitting it if there is interest.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34992 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is in part based on a patch send by Nathan Hintz <nlhintz@hotmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34991 3c298f89-4303-0410-b956-a3cf2f4a3e73
Adjust the IRQ Flag value from 8 to 7 for I2S Core for BCM4716 and
BCM4748 (per the Broadcom SDK). IRQ Flag values greater than 7 are
ignored when setting the interrupt masks.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34990 3c298f89-4303-0410-b956-a3cf2f4a3e73
This was party inspirited by patches send by Nathan Hintz <nlhintz@hotmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34989 3c298f89-4303-0410-b956-a3cf2f4a3e73
This is the version like it was send for mainline inclusion.
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34988 3c298f89-4303-0410-b956-a3cf2f4a3e73
* Add support for blocking forwarding while address assignments
* Fix relay restarting function
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34985 3c298f89-4303-0410-b956-a3cf2f4a3e73
Neither --create-backup nor --restore-backup need an image name (following
the backup filename). Treat them in uniform way.
Mostly fixes#12346.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34974 3c298f89-4303-0410-b956-a3cf2f4a3e73
- introduce "list interface" options to specify the ifaces to listen on, takes uci- or network device name
- set the default system description to distrib @ hostname, e.g. "OpenWrt Barrier Breaker r34744 @ vbox"
- introduce "option lldp_description" to override the automatically generated description
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34970 3c298f89-4303-0410-b956-a3cf2f4a3e73
The folder layout changed between 3.6 and 3.7
Signed-off-by: John Crispin <blogic@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34960 3c298f89-4303-0410-b956-a3cf2f4a3e73
Based on a patch from #12711
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34956 3c298f89-4303-0410-b956-a3cf2f4a3e73
Based on a patch from #12711
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34955 3c298f89-4303-0410-b956-a3cf2f4a3e73
Also add a compatibility patch for 3.3.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@34950 3c298f89-4303-0410-b956-a3cf2f4a3e73
Steven Barth
Jonas Gorski
Jo-Philipp Wich
John Crispin
Felix Fietkau
Hauke Mehrtens
Gabor Juhos